Search NASA⌕ Search

SEARCH · Search NASA

Results for “DRAWING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Planar Anisotropy, Tension–Compression Asymmetry, and Deep Drawing Behavior of Commercially Pure Titanium at Room Temperature

The planar anisotropy (PA) and tension–compression asymmetry (TCA) of the CP-Ti were investigated via uniaxial tension and compression tests at room temperature. The formability and the earing behavior of the CP-Ti sheet were studied via deep drawing experiment. The deep drawing simulations using the uniaxial tensile and the compressive curves as the hardening rules were compared with each other and with the experimental results. The CP-Ti sheet showed PA and TCA in yielding and strain hardening. The PA was characterized by the plastic strain ratio r{sub 0}, r{sub 45}, and r{sub 90} of 1.47, 2.06, and 2.05. The TCA showed PA, which showed tension–compression yield strength ratios of 1.12, 1.08, and 1.04 in 0°, 45°, and 90° in the rolling direction, and tensile and compressive hardening exponent ratios of 0.86, 0.8, and 0.62. The orientation distribution functions (ODFs) analysis demonstrated that the tensile and the compressive deformation textures were different and showed PA. The simulative results, including the simulated forming force and the earing profiles using the uniaxial tensile and compressive curves as the hardening rules, were not in agreement with each other. The results were not in good agreement with the experimental results, implying that the TCA had an important effect on the formability of the sheet. The TCA tended to reduce the thickness of the deep drawing parts, increase the earing ratio, and affect the drawing force.

36 MATERIALS SCIENCE↗

Study on the Deformation Homogeneity and Electrical Conductivity in Co-Cr-Ni-Mo Wires Drawn with Different Drawing Practices

This study investigates the influence of cold wire drawing practices namely full die drawing (FDD) and half die drawing (HDD) on the deformation homogeneity in Co-35Ni-20Cr-10Mo alloy (MP35N) wires which are used for manufacturing implantable medical products. The inhomogeneous factor was used to assess the level of inhomogeneity in the wires, and electrical conductivity was measured on the wires, after drawn to different cold work (CW) reductions and with different drawing practices. Electron beam scattered diffraction, field emission scanning electron microscope and transmission electron microscope characterization were performed on the wire samples to correlate the mechanical and electrical properties to their texture and grain size. The results of this study conclude that the wires drawn with the FDD practice exhibited homogenous deformation, uniform microstructural and hardness gradient across the wire when compared to HDD wires. The electrical conductivity of the HDD-drawn wires was higher than the FDD wires and the level of inhomogeneity and the variation of conductivity decreased with the increase in CW.

36 MATERIALS SCIENCE↗

Prediction of Central Burst Defects in Copper Wire Drawing Process

In this study, the prediction of chevron cracks (central bursts) in copper wire drawing process is investigated using experimental and numerical approaches. The conditions of the chevron cracks creation along the wire axis depend on (i) the die angle, the friction coefficient between the die and the wire, (ii) the reduction in crosssectional area of the wire, (iii) the material properties and (iv) the drawing velocity or strain rate. Under various drawing conditions, a numerical simulation for the prediction of central burst defects is presented using an axisymmetric finite element model. This model is based on the application of the Cockcroft and Latham fracture criterion. This criterion was used as the damage value to estimate if and where defects will occur during the copper wire drawing. The critical damage value of the material is obtained from a uniaxial tensile test. The results show that the die angle and the reduction ratio have a significant effect on the stress distribution and the maximum damage value. The central bursts are expected to occur when the die angle and reduction ratio reach a critical value. Numerical predictions are compared with experimental observations.

36 MATERIALS SCIENCE↗

Realistic Hot Water Draw Specification for Rating Solar Water Heaters: Preprint

In the United States, annual performance ratings for solar water heaters are simulated, using TMY weather and specified water draw. A more-realistic ratings draw is proposed that eliminates most bias by improving mains inlet temperature and by specifying realistic hot water use. This paper outlines the current and the proposed draws and estimates typical ratings changes from draw specificationchanges for typical systems in four cities.

14 SOLAR ENERGY↗

Springback Analysis of Draw-Bending of 980 MPa Cold Rolled Steel Sheet and Its Experimental Validation

Draw-bending experiment is carried out using a 1.2 mm-thick high strength steel sheet with a tensile strength of 980 MPa and the residual curvature of the draw-bent specimens are precisely measured. The die profile of the draw-bending testing machine rotates, so that the effect of friction force on the curvature data after springback can be neglected. Moreover, in order to quantitatively evaluate the Bauschinger effect of the test material, stress reversal tests are performed using an in-plane stress reversal testing machine. Furthermore, the finite element analyses (FEA) of the draw-bending experiment are carried out. The effect of the work hardening models (isotropic or combined), element types (shell or solid), and the number of integration points in the through-thickness direction on the amount of springback (residual curvature) are investigated in detail.

36 MATERIALS SCIENCE↗

Engineering Drawing Practices: Volume I of I - Aerospace and Ground Support Equipment

KSC-GP-435,Engineering Drawing Practices, Volume I of II, Aerospace and Ground Support Equipment, establishes the conventions to be adhered to by engineering and drafting personnel in the preparation, revision, and completion of engineering digital product definition data sets. This manual sets forth the minimum requirements acceptable at Kennedy Space Center (KSC) for the preparation of model-only, model and dependent drawing, and drawing-only digital product definition data sets based on the engineering drawing and model requirements in the ASME Y14 series.

Wendy Ledezma↗

Drawing 445754 rev5

Drawing 445754 contains the details for fabricating plastic flux wands used in ATR and ATRC. The flux wands are used to position flux wires in fuel elements. The flux wands are basically a tool to position the flux wires. The flux wires are later removed from the flux wands and counted to determine the amount of flux they received. The flux wands come in contact with reactor primary coolant, but do not control the primary coolant (this is in reference to 10 CFR Part 810). Additional wands need to be fabricated. This drawing needs to be sent to a vendor or vendors for procurement of new flux wands as done in the past. LWP-11201 rev 11 (pg. 27) indicates providing information to a vender is not a public release. This drawing does not need to be released to all of the public if that is an option. It just needs to go to a vendors or vendors. A vendor will likely need to see the drawing to determine if they can build the flux wands.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Study of Novel Hexavalent Phosphazene Salts as Draw Solutes in Forward Osmosis

Two novel multi-valent salts based on phosphazene chemistry have been synthesized and characterized as forward osmosis (FO) draw solutes. Commercially obtained hexachlorocyclotriphosphazene was reacted with the sodium salt of 4-ethylhydroxybenzoate to yield hexa(4-ethylcarboxylatophenoxy)phosphazene. Hydrolysis, followed by and neutralization with NaOH or LiOH, of the resulting acidic moieties yielded water soluble sodium and lithium phosphazene salts, respectively. Degrees of dissociation were determined through osmometry over the range of 0.05-0.5 m, giving degrees of 3.08-4.95 per mole, suggesting a high osmotic potential. The Li salt was found to be more ionized in solution than the sodium salt, and this was reflected in FO experiments where the Li salt gave higher initial fluxes (~ 7 L/m2h) as compared to the sodium salt (~6 L/m2h) at identical 0.07 m draw solution concentrations at 30 °C. Longer term experiments revealed no detectable degradation of the salts; however some hydrolysis of the cellulose acetate membrane was observed, presumably due to the pH of the phosphazene salt draw solution (pH = ~8).

36 MATERIALS SCIENCE↗

Evolution of cementite morphology in pearlitic steel wire during wet wire drawing

The evolution of the cementite phase during wet wire drawing of a pearlitic steel wire has been followed as a function of strain. Particular attention has been given to a quantitative characterization of changes in the alignment and in the dimensions of the cementite phase. Scanning electron microscope observations show that cementite plates become increasingly aligned with the wire axis as the drawing strain is increased. Measurements in the transmission electron microscope show that the cementite deforms plastically during wire drawing , with the average thickness of the cementite plates decreasing from 19 nm ({epsilon} = 0) to 2 nm ({epsilon} = 3.7) in correspondence with the reduction in wire diameter. The deformation of the cementite is strongly related to plastic deformation in the ferrite, with coarse slip steps, shear bands and cracks in the cementite plates/particles observed parallel to either {l_brace}110{r_brace}{sub {alpha}} or {l_brace}112{r_brace}{sub {alpha}} slip plane traces in the ferrite.

36 MATERIALS SCIENCE↗

Process metallurgy simulation for metal drawing process optimization by using two-scale finite element method

We developed two-scale FE analysis procedure based on the crystallographic homogenization method by considering the hierarchical structure of poly-crystal aluminium alloy metal. It can be characterized as the combination of two-scale structure, such as the microscopic polycrystal structure and the macroscopic elastic plastic continuum. Micro polycrystal structure can be modeled as a three dimensional representative volume element (RVE). RVE is featured as by 3×3×3 eight-nodes solid finite elements, which has 216 crystal orientations. This FE analysis code can predict the deformation, strain and stress evolutions in the wire drawing processes in the macro- scales, and further the crystal texture and hardening evolutions in the micro-scale. In this study, we analyzed the texture evolution in the wire drawing processes by our two-scale FE analysis code under conditions of various drawing angles of dice. We evaluates the texture evolution in the surface and center regions of the wire cross section, and to clarify the effects of processing conditions on the texture evolution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Community Geothermal: Mechanical, Electrical, and Plumbing Design Report and Drawings - Wallingford, CT

Included here are the mechanical, electrical, and plumbing design report and drawings for the proposed community geothermal system at an affordable housing complex in Wallingford, Connecticut. The report and drawings were developed by LN Consulting, in partnership with the University of Connecticut, which completed the energy modeling that formed the basis of the design work. The drawings can be used as a basis for a Request for Proposals to procure entities to complete construction-ready design documents.

15 GEOTHERMAL ENERGY↗

Process Simulation of Aluminium Sheet Metal Deep Drawing at Elevated Temperatures

Lightweight design is essential for an economic and environmentally friendly vehicle. Aluminium sheet metal is well known for its ability to improve the strength to weight ratio of lightweight structures. One disadvantage of aluminium is that it is less formable than steel. Therefore complex part geometries can only be realized by expensive multi-step production processes. One method for overcoming this disadvantage is deep drawing at elevated temperatures. In this way the formability of aluminium sheet metal can be improved significantly, and the number of necessary production steps can thereby be reduced. This paper introduces deep drawing of aluminium sheet metal at elevated temperatures, a corresponding simulation method, a characteristic process and its optimization. The temperature and strain rate dependent material properties of a 5xxx series alloy and their modelling are discussed. A three dimensional thermomechanically coupled finite element deep drawing simulation model and its validation are presented. Based on the validated simulation model an optimised process strategy regarding formability, time and cost is introduced.

36 MATERIALS SCIENCE↗

Validation of formability of laminated sheet metal for deep drawing process using GTN damage model

In this study, we studied formability of PET/PVC laminated sheet metal which named VCM (Vinyl Coated Metal). VCM offers various patterns and good-looking metal steel used for appliances such as refrigerator and washing machine. But, this sheet has problems which are crack and peeling of film when the material is formed by deep drawing process. To predict the problems, we used finite element method and GTN (Gurson-Tvergaard-Needleman) damage model to represent damage of material. We divided the VCM into 3 layers (PET film, adhesive and steel added PVC) in finite element analysis model to express the crack and peeling phenomenon. The material properties of each layer are determined by reverse engineering based on tensile test result. Furthermore, we performed the simple rectangular deep drawing and simulated it. The simulation result shows good agreement with drawing experiment result in position, punch stroke of crack occurrence. Also, we studied the fracture mechanism of PET film on VCM by comparing the width direction strain of metal and PET film.

97 MATHEMATICS AND COMPUTING↗

Line-drawing algorithms for parallel machines

The fact that conventional line-drawing algorithms, when applied directly on parallel machines, can lead to very inefficient codes is addressed. It is suggested that instead of modifying an existing algorithm for a parallel machine, a more efficient implementation can be produced by going back to the invariants in the definition. Popular line-drawing algorithms are compared with two alternatives; distance to a line (a point is on the line if sufficiently close to it) and intersection with a line (a point on the line if an intersection point). For massively parallel single-instruction-multiple-data (SIMD) machines (with thousands of processors and up), the alternatives provide viable line-drawing algorithms. Because of the pixel-per-processor mapping, their performance is independent of the line length and orientation.

Pang, Alex T.↗

Airborne Laboratory Apparatus Draws Glass Fibers

Glass-fiber-drawing apparatus designed for studies of effect of gravitation on drawing process. Clear plastic housing surrounds fiber-drawing equipment and some of associated electronic instrumentation. External rack holds video monitor, personal computer, keyboard, videotape recorder, and power switch panel. Mounted in research aircraft, apparatus makes continuous video recordings of formation of fiber at effective gravitational accelerations ranging from 0.001 to 2 times normal Earth gravitational acceleration as aircraft dives, then pulls out of dives. Also records pertinent process data on video image.

Tucker, Dennis S.↗

Auto Draw from Excel Input Files

The design process often involves the use of Excel files during project development. To facilitate communications of the information in the Excel files, drawings are often generated. During the design process, the Excel files are updated often to reflect new input. The problem is that the drawings often lag the updates, often leading to confusion of the current state of the design. The use of this program allows visualization of complex data in a format that is more easily understandable than pages of numbers. Because the graphical output can be updated automatically, the manual labor of diagram drawing can be eliminated. The more frequent update of system diagrams can reduce confusion and reduce errors and is likely to uncover symmetric problems earlier in the design cycle, thus reducing rework and redesign.

Strauss, Karl F.↗