Search NASA⌕ Search

SEARCH · Search NASA

Results for “FCCI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Fuel-Cladding Eutectic Study of Legacy Fast Flux Test Facility (FFTF) MFF HT9/U-10Zr Metallic Fuel

This report presents the first systematic investigation of fuel-cladding eutectic interaction (FCEI) in irradiated HT9/U-10Zr metallic fuel from the Fast Flux Test Facility (FFTF) Materials Fuels Form (MFF) program, using differential scanning calorimetry (DSC) coupled with scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Two irradiated fuel cross-sections, MNT07H (9.5 at% burnup, x/L = 0.78) and MNT08H (7.0 at% burnup, x/L = 0.93), were subjected to three successive isothermal annealing rounds (R1–R3) at 820°C for 20 minutes each, yielding a cumulative transient duration of one hour. This study directly addresses a recognized gap in the existing FCEI database, which previously lacked irradiated HT9/U-10Zr data at burnup levels above 8 at%. Two principal findings emerge from the study. First, for both samples, FCEI remained spatially confined within the pre-existing fuel-cladding chemical interaction (FCCI) zone boundaries after R3, with no measurable eutectic penetration into unaffected cladding beyond the original FCCI layer. This self-limiting behavior is consistent with historical Fuel Behavior Test Apparatus (FBTA) results and is attributed to the near-eutectic phase composition of the FCCI zone, which rapidly absorb the available eutectic-forming constituents and then stall penetration once the FCCI zone is consumed. A comparison with unirradiated surrogate data further supports this mechanism: whereas a U–34 at.% Fe sample would be expected to show ~176 µm of iron penetration under comparable conditions, the irradiated samples exhibited only ~20 µm, a discrepancy attributed to irradiation-induced interfacial porosity and pre-existing FCCI composition gradients. Second, for MNT08H, FCEI was observed exclusively on the half of the cladding circumference where pre-existing steady-state FCCI was present, with no detectable FCEI on the opposite half. Three hypotheses are proposed to explain this asymmetry: the inhibiting role of a zirconium-rich rind at the fuel-cladding interface; the chemical sequestration of iron by redistributed zirconium within the fuel matrix; and the persistence of fuel-cladding gaps on the FCEI-free half that preclude direct contact. All three hypotheses require further experimental investigation. The results extend the empirical FCEI database into higher-burnup territory and demonstrate the viability of DSC-based testing as a substitute for the no-longer-available FBTA apparatus. Future work will include additional cross-section testing, compilation of the full FCEI dataset, model evaluation, and DSC testing of ternary fuel compositions to broaden the experimental basis for safety assessment of sodium-cooled fast reactor systems.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Small-scale mechanical testing and characterization of fuel cladding chemical interaction between HT9 cladding and advanced U-based metallic fuel alloy

Fuel cladding chemical interactions (FCCI) occurred on the interface between the nuclear metal fuel and cladding is the primary cause of cladding wastage, weakening cladding mechanical integrity, and placing fuel and cladding at risk. Although the microstructural and phase information of FCCI has been fairly understood, mechanical properties remain less studied due to limited reaction volume. Here, through a combining of advanced electron microscopy characterizations and small-scale mechanical testing techniques, including indentation and micro-tensile testing, this study investigated the microscale mechanical properties of FCCI between the ferritic/martensitic (F/M) HT9 cladding and an advanced Uranium (U)-based metallic fuel irradiated at the Advanced Test Reactor to 2.2% FIMA with peak inner cladding temperature reached to 650 °C. Mechanical testing results show significant hardening and embrittlement in the FCCI region. The brittle fracture of FCCI specimen is mainly attributed to the formation of nano-crystallized intermetallic σ-FeCr phase. Whereas mechanical softening was revealed in the unreacted HT9 matrix due to irradiation-induced microstructural and microchemical evolution, specifically, the disappearance of martensitic lath structure and the formation of Fe 2 Mo Laves phase precipitation which consumed the solid solution strengthening Mo from the F/M HT9 matrix. Due to the achieved high cladding temperature, this fuel pin is of particular significance for revealing the high-temperature irradiation effect on the mechanical properties of HT9 cladding. Therefore, the outcomes of this study are expected to contribute to the development of multi-scale mechanical behavior modeling of HT9 cladding for Generation IV reactors which requires cladding to run at higher temperature (above 600 ?).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Innovative coating of nanostructured vanadium carbide on the F/M cladding tube inner surface for mitigating the fuel cladding chemical interactions

Fuel cladding chemical interactions (FCCI) have been acknowledged as a critical issue in a metallic fuel/steel cladding system due to the formation of low melting intermetallic eutectic compounds between the fuel and cladding steel, resulting in reduction in cladding wall thickness as well as a formation of eutectic compounds that can initiate melting in the fuel at lower temperature. In order to mitigate FCCI, diffusion barrier coatings on the cladding inner surface have been considered. In order to generate the required coating techniques, pack cementation, electroplating, and electrophoretic deposition have been investigated. However, these methods require a high processing temperature of above 700 oC, resulting in decarburization and decomposition of the martensites in a ferritic/martensitic (F/M) cladding steel. Alternatively, organometallic chemical vapor deposition (OMCVD) can be a promising process due to its low processing temperature of below 600 oC. The aim of the project is to conduct applied and fundamental research towards the development of diffusion barrier coatings on the inner surface of F/M fuel cladding tubes. Advanced cladding steels such as T91, HT9 and NF616 have been developed and extensively studied as advanced cladding materials due to their excellent irradiation and corrosion resistance. However, the FCCI accelerated by the elevated temperature and high neutron exposure anticipated in fast reactors, can have severe detrimental effects on the cladding steels through the diffusion of Fe into fuel and lanthanides towards into the claddings. To test the functionality of developed coating layer, the diffusion couple experiments were focused on using T91 as cladding and Ce as a surrogate lanthanum fission product. By using the customized OMCVD coating equipment, thin and compact layers with a few micron between 1.5 µm and 8 µm thick and average grain size of 200 nm and 5 µm were successfully obtained at the specimen coated between 300oC and 500 oC, respectively. The coating layer contains both carbon and vanadium elements as quantified by WED, and the phases mainly consist of a mixture of V2C and VC, which was confirmed using X-ray diffraction patterns. In addition, the ratio between V and C varies with processing temperature, and it was observed that a higher temperature promotes the carbon adsorption and increases thickness of the coating. With optimized deposition conditions, we can apply the coating technique toward the actual T91 cladding materials, and provide the possibilities for the real application in sodium-cooled fast reactors (SFRs). Diffusion couple experiments were performed at both 550 oC and 690 oC, which corresponds to normal and aggressive operating temperatures, respectively. The results show that vanadium carbide coating with wider thickness (8 µm) and lower carbon concentration (27 at.%) reduced the width of the inter diffusion region, indicating that vanadium carbide coating can mitigate FCCI effectively. In specific, inter-diffusion between Fe and Ce was prohibited over most area, but Ce diffusion occurred toward the coating and the Fe substrate through thinner coating layer, which needs further optimization in terms of uniform coating thickness. Overall, it is concluded that this coating process can be successfully applied onto the inner surface of HT9 cladding tubes and the FCCI can be effectively mitigated if not totally eliminated.

36 MATERIALS SCIENCE↗

Highlights from the Postirradiation Examination of AFC-3A and AFC-3B

Highlights from the postirradiation examination of the AFC-3A and AFC-3B irradiation test are presented. Baseline non-destructive and destructive examinations of these tests have been completed at this time. Results from visual examination, neutron radiography, gamma spectrometry, dimensional inspection, fission gas release, chemical burnup analysis, and optical microscopy have been collected. All the rodlets from these irradiations appear to have performed well during irradiation. Baseline PIE has been completed on rodlets from AFC- 3A, and AFC-3B. This includes visual exams, neutron radiography, gamma spectrometry. dimensional inspection, fission gas release evaluation, optical microscopy. microhardness evaluation. and chemical analysis. The results compiled here are a sampling of the full results. Baseline PIE provides an engineering or macroscopic scale evaluation of fuel performance and prepares samples for a more detailed phenomenological study of observed performance. Advanced PIE techniques are desired to obtain microscopic elemental and structural information both in the fuel, in the cladding, and in the interface where the composition of the FCCI layer is of great interest. The AFC-3 tests do appear to have performed roughly as designed during the irradiation. The FCCI behavior of Mo alloy metallic fuel versus Zr alloy metallic fuel has been confirmed. Results from this irradiation such as the FCCI observed in AFC-3A R1 and AFC-3A R2 can be used to eliminate Mo alloys as a choice in future irradiations where ultra-high burnup is a stated goal. Annular fuels are a preferred method for many high burnup core designs. The redistribution behavior of the annular U-Zr alloys should be studied further to better understand how this might impact high burnup annular fuel performance. The thermal bonding between annular fuel and cladding should also be studied further as there appear to be localized areas of FCCI forming in both AFC-3A R4 and AFC-3B R2, while no FCCI was observed in the Zr-based Na-bonded or Mo-based low smear density Na-bonded fuel. The performance of the low smear density. solid fuels is less clear. The neutron radiography and optical microscopy cross sections suggest the fuel is not forming a radially symmetric structure which may be causing undesirable localized temperature variations. Further study both by electron microscopy and by simulation to evaluate the implications of the non-symmetric fuel form are needed to better understand whether this fuel form merits further study under irradiation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel-cladding chemical interaction of a prototype annular U-10Zr fuel with Fe-12Cr ferritic/martensitic HT-9 cladding

As an alternative fuel form, the annular metallic fuel design eliminates the liquid sodium bond between the fuel and the cladding, providing back-end fuel cycle and other benefits. The fuel-cladding chemical interaction (FCCI) of annular fuel also presents new features. In this work, state-of-the-art electron microscopy and spectroscopy techniques were used to study the FCCI of a prototype annular U-10wt%Zr (U-10Zr) fuel with ferritic/martensitic HT-9 cladding irradiated to 3.3% fission per initial heavy atom. Compared with sodium-bonded solid fuels, negligible amounts of lanthanides were found in the FCCI layer in the investigated helium-bonded annular fuel. Instead, most lanthanides were retained in the newly formed UZr 2 phase in the fuel center region. The interdiffusion of iron and uranium resulted in tetragonal ( U ,Zr) 6 Fe phase (space group I4/mcm) and cubic ( U ,Zr)( Fe ,Cr) 2 phase (space group Fd 3 ¯ m). The ( U ,Zr)( Fe ,Cr) 2 phase contains a high density of voids and intergranular uranium monocarbides of NaCl-type crystal structure (space group Fm 3 ¯ m). At the interdiffusion zone and inner cladding interface, a porous lamellar structure composed of alternating Cr-rich layers and U-rich layers was observed. Next to the lamellar region, the unexpected phase transformation from body-centered cubic ferrite (α-Fe) to tetragonal binary Fe-Cr σ phase (space group P4 2 /mnm) occurred, and tetragonal Fe-Cr-U-Si phase (space group I4/mmm) was identified. Due to the diffusion of carbon into the interdiffusion zone, carbon depletion inside the HT-9 led to the disappearance of the martensite lath structure, and intergranular U-rich carbides formed as a result of the diffusion of uranium into the cladding. These detailed new findings reveal the unique features of the FCCI behavior of annular U-Zr fuels, which could be a promising alternative fuel form for high burnup fast reactor applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The effect of temperature and burnup on U-10Zr metallic fuel chemical interaction with HT-9: A SEM-EDS study

The fuel cladding chemical interaction (FCCI) between Uranium-Zirconium-based metallic fuel and cladding materials during in-pile service is one of the most constraining phenomena affecting the performance of this fuel system. In this study, we investigated the effect of temperature and burnup on the FCCI development in two U-10 wt.% Zr (U-10Zr) fuel samples with HT-9 cladding irradiated as part of the MFF-3 irradiation test in the Fast Flux Test Facility (FFTF). One sample achieved a burnup of 13.1 at.% and operated with an average inner cladding temperature of 530°C, while the other achieved a burnup of 8.5 at.% and was subjected to an average inner cladding temperature of 615°C. Automated scanning electron microscopy (SEM) back-scattered electron (BSE) imaging of entire fuel cross-sections and SEM energy dispersive x-ray spectroscopy (EDS) analysis on specific fuel-cladding interface regions successfully provided a comprehensive characterization of the depth and type of interaction happening under different irradiation conditions. Further, our analysis shows that FCCI development on both fuel and cladding side is strongly influenced by the inner cladding temperature and, to some extent, the formation and integrity of Zr-rich layers between the fuel and cladding, while the impact of burnup and power is negligible. Measured FCCI thicknesses were compared to BISON simulations using both an empirical model based upon legacy data from the Experimental Breeder Reactor II (EBR II) irradiations and a mechanistic model currently under development for the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, showing satisfactory agreement. Nonetheless, this comparison supports the need for additional microstructural characterization in intermediate ranges of temperature, power, and burnups in prototypic-length pins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improvement of mechanistic fuel-cladding chemical interaction modeling in BISON

This report describes work performed during FY2024 under the auspices of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program to inform and improve mechanistic models of fuel-cladding chemical interaction (FCCI) in metallic fuel. For fuel-side FCCI, atomistic simulations were performed to determine the diffusivity of iron (Fe) in the $\alpha$ and $\gamma$ phases of uranium (U). A model of liquid penetration of cladding due to melting of the fuel-side FCCI region was updated to account for the finite size of the FCCI region, and the model was validated through comparison with tests performed in the Fuel Behavior Test Apparatus (FBTA). For cladding wastage formation, a reduced-order model was improved by comparison with a multi-scale mechanistic model to better quantify the ROM parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Core materials development for the fuel cycle R&D program

The Fuel Cycle Research and Development program is investigating methods of burning minor actinides in a transmutation fuel. One of the challenges of achieving this goal is to develop fuels capable of reaching extreme burnup levels (e.g. 40%). To achieve such high burnup levels’ fast reactor core materials (cladding and duct) must be able to withstand very high doses (>300 dpa design goal) while in contact with the coolant and the fuel. Thus, these materials must withstand radiation effects that promote low temperature embrittlement, radiation induced segregation, high temperature helium embrittlement, swelling, accelerated creep, corrosion with the coolant, and chemical interaction with the fuel (FCCI). To develop and qualify materials to a total fluence greater than 200 dpa requires development of advanced alloys and irradiations in fast reactors to test these alloys. Test specimens of ferritic/martensitic alloys (T91/HT-9) previously irradiated in the FFTF reactor up to 210 dpa at a temperature range of 350– 750 °C are presently being tested. This includes analysis of a duct made of HT-9 after irradiation to a total dose of 155 dpa at temperatures from 370 to 510 °C. Compact tension, charpy and tensile specimens have been machined from this duct and mechanical testing as well as SANS and Mossbauer spectroscopy are currently being performed. Initial results from compression testing and Charpy testing reveal a strong increase in yield stress (~400 MPa) and a large increase in DBTT (up to 230 °C) for specimens irradiated at 383 °C to a dose of 28 dpa. Less hardening and a smaller increase in DBTT was observed for specimens irradiated at higher temperatures up to 500 °C. Advanced radiation tolerant materials are also being developed to enable the desired extreme fuel burnup levels. Specifically, coatings are being developed to minimize FCCI, and research is underway to fabricate large heats of radiation tolerant oxide dispersion steels with homogeneous oxide dispersions.

Maloy, S. A.↗

A Design and Fabrication Options Trade Study for Metallic Fuel without Internal Sodium Bonding

Nuclear fuels using alloys of uranium, or metallic fuels, have many beneficial properties. The classical metallic fuel design uses a loose fitting cylindrical “slug” of fuel placed inside stainless-steel cladding tubes where the gap is filled with sodium. This sodium bond is liquid at operating temperature and conducts heat from the slug to the cladding, especially in early life before fuel swells into contact with the cladding. Despite the benefits of sodium bonding, there is a desire to develop metallic fuel technologies without it chiefly to reduce chemical reaction hazards in spent fuel storage from sodium fast reactors operating on once-through fuel cycles. Elimination of the sodium bond may also help unlock potential benefits for fuel fabrication, reactor neutronics, and compatibility with other types of reactors. Creating a sodium-free metallic fuel revolves around the problem of manufacturing fuel slug geometries which are in close contact with the cladding at beginning of life to facilitate heat transport while alleviating fuel-cladding chemical interactions (FCCI) at this interface and providing enough free volume to accommodate fuel swelling. Accelerating development and qualification of this fuel system will require careful selection of design and manufacturing options. To this end, a design trade-off study was performed to evaluate candidate options. Several design and manufacturing options were assessed, weighted, scored, and ranked with respect to fabrication, normal reactor operation, off-normal scenarios, and back-end considerations. This effort was performed both for “baseline” needs, which represented a once-through fuel cycle at temperatures and burnups known to be viable for sodium-bonded metallic fuel, and for “enhanced” needs to represent opportunities for closed fuel cycles and/or more aggressive temperatures/burnups. The outcomes of this study prioritized a baseline technology using U-Zr alloy with additives to mitigate FCCI, produced in annular slug geometry by continuous casting, clad in austenitic stainless-steel alloy, and followed by a final step to swage the cladding down to close the gap. This study prioritized an enhanced fuel technology using U-Mo alloy, also produced by continuous casting into an annular geometry, followed by coating/plating with an FCCI barrier on the slug, again with a final step to swage the cladding diameter down using oxide dispersion strengthened steel. It was noted that development of the enhanced fuel technology would entail more risk, thus U-Zr alloy was put forth as a backup to U-Mo if challenges are encountered with FCCI barriers, and advanced ferritic/martensitic steels are put forth as a backup to oxide dispersion strengthened steels if swaging and welding are found unworkable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Lanthanides in Metallic Nuclear Fuels: Their Behavior and Methods for Their Control

The thermodynamic and experimental basis is given for using dopant additives to bind lanthanides as intermetallic compounds in metallic nuclear fuels. Lanthanide fission products are a major factor in limiting the lifetime of the fuel, because they migrate to the fuel slug peripheral surface where they participate in fuel-cladding chemical interactions (FCCI) with the steel cladding. Lanthanide carryover in recycled metal fuels can accelerate FCCI, as recycled lanthanides would likely segregate from the fuel phase, putting the lanthanides in prompt contact with the cladding. In out-of-pile tests we examined the use of Pd for binding the lanthanides, with Pd selected because of its known metallurgical properties in fuel related systems and because of its known behavior in irradiated EBR-II fuels. Initial results confirmed that palladium may be expected to mitigate FCCI arising from lanthanides, and it has been recommended for in-pile tests. We also evaluated transport phenomena responsible for lanthanide migration, and identified liquid-like behaviors as being dominant. Liquid-like behaviors include transport with liquid metals, liquid metal solutions, and rapid surface transport of alloys/metals near their melting temperatures. The analysis led to establishing general criteria for selecting alternate dopant additives, and identifying Sn, Sb, and Te as alternates for further testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of U-10Zr-2Sn-2Sb and U-10Zr-2Sn-2Sb-4Ln to assess Sn+Sb as a mixed additive system to bind lanthanides

In this paper, tin and antimony are being investigated as potential additives to metallic fuel to control fuel-cladding chemical interaction (FCCI). A primary cause of FCCI is lanthanide fission products moving to the fuel periphery and interacting with the cladding. This interaction can lead to wastage of the cladding and, given enough time or burn-up, eventually to a cladding breach. The current study involves a microstructural characterization of as-cast and annealed U-10Zr-2Sn-2Sb and U-10Zr-2Sn-2Sb-4Ln, where Ln = 53Nd-25Ce-16Pr-6La, all in wt %, as alloys which could prevent FCCI. Scanning electron microscopy (SEM) analysis and X-ray powder diffraction indicates the additive-Zr compound in U-10Zr-2Sn-2Sb is Zr 5 (Sn,Sb) 3 , while the additive-Ln compound being formed in U-10Zr-2Sn-2Sb-4Ln is Ln 5 (Sn,Sb) 4 , with significantly more Sb than Sn (37 at. % versus 6 at. %, respectively). The bulk of the Sn, with a small amount of Sb, remained as Zr 5 (Sn,Sb) 3 precipitates. Finally, the potential benefits of a mixed additive system, along with relative stabilities of the intermetallic compounds, are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure and diffusion behavior of uranium fuel with minor additives

Fission product lanthanides in metallic fuels are known to cause adverse fuel-cladding chemical interaction (FCCI). Tin (Sn) and palladium (Pd) are being explored as the potential additives to reduce or mitigate lanthanide-induced FCCI by forming stable Sn-Ln and Pd-Ln compounds. The current study is an investigation of the fuel alloys, U–4Sn, U–4Sn-4Ln, U–4Pd, and U–4Pd-4Ln (wt. %), and their diffusion behaviors with Fe. Microstructural analysis was performed using scanning electron microscopy (SEM). Further, the binary phases in the UPd and USn alloys are identified as UPd 3 and suspected U 2 Sn, where U 2 Sn is unknown in the literature. The binary phases in the UPdLn alloy are identified as PdLn and Pd-rich Pd-Ln (Pd 4 Ln 3 and Pd 3 Ln 2 ), and in the USnLn alloy is SnLn. Diffusion of Fe with these binary phases is insignificant compared to the diffusion with U. The Ln-induced FCCI can be mitigated by the additives.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transmission Electron Microscopy Characterization of Fuel Cladding Chemical Interaction between Minor Actinides bearing U-Pu-Zr Fuel and AIM1 Cladding

Minor actinides (MA) significantly contribute to the long-term radiotoxicity of spent nuclear fuel (SNF). Separating MA from SNF and incorporating it into metallic fuels for fast reactor transmutation is a potential method to reduce this radiotoxicity. Here, this study focuses on transmission electron microscopy characterization of two samples from the fuel cladding chemical interaction (FCCI) region of an americium (Am) and neptunium (Np)-bearing (MA-bearing) uranium-plutonium-zirconium (U-Pu-Zr) fuel irradiated in the Phenix fast reactor to 9.5 % FIMA burnup at approximately 550 °C cladding temperature. The results show that despite the complex chemical interactions between MA and AIM1 cladding elements, excessive FCCI was not induced, and Am penetration depth in the cladding limited to less than 4 µm. Np remained mostly inside fuel. The Zr-rich compounds layer effectively limited the accumulation of lanthanide on the inner cladding surface. Overall, the FCCI behavior between investigated MA-bearing U-Pu-Zr fuel and AIM1 cladding is benign.

Chemical interaction↗

Elucidating the effect of minor-actinide addition on fuel-cladding chemical interaction in an HT-9 clad U-Pu-Zr metallic fuel irradiated to 6.15 at.% burnup in EBR-II

Scanning and transmission electron microscopy (S/TEM) were used to characterize the local fuel-cladding chemical interaction (FCCI) in one cross-section taken from a HT-9 clad U-20.3Pu-10Zr-1.2Am-1.3Np (in wt.%) fuel irradiated to 6.15 at.% burnup with inner cladding temperatures ranging between 460–490 °C. Results showed that the total interaction thickness between fuel and cladding was <10 µm. Fe infiltrated the fuel to form U-Zr-Fe phases while fuel elements or lanthanides did not infiltrate into the cladding. Np was not involved in the formation of any phases in the examined locations; however, Am played a role by forming a ∼2 µm thick homogeneous Fe-Pu-Am planar front at the inner cladding wall. An oxidized Na layer existed in the fuel-cladding gap with Fe and lanthanide particles dispersed within, suggesting Na could facilitate the transport of fuel and cladding constituents. Secondary phases, including an FCC Zr-rich phase, lanthanide phases, and α’-Cr(Fe) were identified in the outer fuel and FCCI regions. Furthermore, this study suggests that, for the irradiation conditions specific to this cross-section, minor actinides have little impact on FCCI behavior beyond what would be observed in typical HT-9 clad U-Pu-Zr fuel pins systems.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of Fuel Cladding Chemical Interaction on a High Burnup U-10Zr Metallic Fuel via Electron Energy Loss Spectroscopy Enhanced by Machine Learning

Fuel cladding chemical interaction (FCCI) is one of the main performance limiting factors for metallic nuclear fuels. The interaction destabilizes the martensitic microstructure and deteriorates mechanical properties of HT-9 cladding. The detection of low atomic number elements (Z<10) and overlapping of elemental peaks can be problematic in interpreting energy dispersive X-ray spectroscopy (EDS) data. Electron energy loss spectroscopy (EELS) provides precise elemental edge energy values and can detect elements with a low atomic number. This work utilizes EELS to study the distribution of lanthanides and light elements at the interaction region. The sample was prepared from the FCCI region of a U-10Zr (wt.%) solid fuel with HT-9 cladding, irradiated to a burnup of 13.2 at.%. Processing the EELS data included three major steps: 1) enhance the signal to noise ratio by denoising the spectrum with principal component analysis (PCA) method, removing background and performing deconvolution; 2) identify chemical elements with core energy loss edges; 3) confirm different phases using a popular machine learning method, K-means. This work presents qualitative assessment of lanthanides and light elements like carbon (C) and oxygen (O) enhanced by the application of machine learning algorithms. By comparing with EDS elemental maps, EELS provides higher resolution chemical maps, reveals the distribution of carbon at the interaction region supporting the formation of zirconium carbide, a rind-like microstructure feature that was proposed to mitigate the chemical interaction. Furthermore, the plasmon peak map was also found to indicate an energy shift associated with the formation of phases/compounds. K-means clustering method was used on the processed electron energy loss (EEL) spectrum to automatically reveal different phases. The resulting clustered maps from K-means clustering align well with elemental maps confirming certain phases, especially Fe-Ce and Zr-C, in the FCCI region.

EELS↗

Site specific porosity-thermal performance correlations in neutron irradiated U-10Zr fuel

In this work, we present a site-specific three-dimensional analysis of porosity evolution in neutron-irradiated U–10Zr metallic fuel using high-resolution synchrotron X-ray tomography. Focused ion beam cubic lift-outs from four radial positions—fuel center, middle, edge, and fuel-cladding interaction (FCCI) zones—were imaged, reconstructed, and segmented to quantify pore volume, density, morphology, and pore connectivity. Porosity increased modestly from 5.5% at the center to 10.5% at the edge, yet pore number density increased by over two orders of magnitude in the fuel portion near the FCCI interface (from 4.8 x 10 4 to 6.0 x 10 6 pores/mm 3 ). Morphological classification revealed a progression from small spherical pores at the center to equiaxed and tortuous networks at the periphery, with enhanced orientation along the radial direction. Connectivity and permeability analysis reveal that the FCCI region maintains dense, highly interconnected pores despite a moderate volume fraction, enabling rapid fission gas transport and lanthanide migration. Effective thermal conductivity models incorporating sodium logging confirm that these site-specific pore features critically influenced heat transport during reactor irradiation. These findings demonstrate that pore topology—not just porosity fraction—controls thermal performance and thermal pathways in U–10Zr fuels, impacting fuel thermal performance in a reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and preliminary validation of a mechanistic multiscale model for fuel-cladding chemical interaction in metallic nuclear fuels

Despite decades of fuel rod material and design improvements, fuel-cladding chemical interaction (FCCI) remains the single-most lifetime-limiting behavior for modern metallic fuel rods. Constraining fuel lifetime increases operating costs, limiting the economic viability of commercializing metallic nuclear fuel technology. A mechanistic multiscale model utilizing the finite element method-based MARMOT and BISON codes was developed to more confidently predict cladding-side FCCI and its impact on fuel performance. The new BISON model incorporates mesoscale models for the effects of fuel microstructure evolution on the transport of wastage-inducing lanthanides through the fuel and for the kinetics of cladding wastage layer growth. The mesoscale models, in turn, build on lanthanide transport property data obtained from the atomistic scale. Preliminary validation studies using wastage thickness and cladding profilometry data from four fuel rods irradiated in Experimental Breeder Reactor II experiment X447 and one fuel rod from Fast Flux Test Facility experiment IFR1 show that the new model predicts cladding wastage and its effects on cladding deformation as well as existing empirical FCCI correlations. The new model is expected to aid in the design of new metallic fuel concepts, including fuel additives, cladding liners, and sodium-free annular fuel geometries. In conclusion, future work will focus on broader validation and refinement of the model’s treatment of different fuel alloys and cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Temperature Fuel Cladding Chemical Interactions Between TRIGA Fuels and 304 Stainless Steel

High-temperature fuel-cladding chemical interactions (FCCI) between TRIGA (Training, Research, Isotopes, General Atomics) fuel elements and the 304 stainless steel (304SS) are of interest to develop an understanding of the fuel behavior during transient reactor scenarios. TRIGA fuels are composed of uranium (U) particles dispersed in a zirconium-hydride (Zr-H) matrix. In reactor, the fuel is encased in 304-stainless-steel (304SS) or Incoloy 800 clad tubes. At high temperatures, the fuel can readily interact with the cladding, resulting in FCCI. A number of FCCI can take place in this system. Interactions can be expected between the cladding and the Zr-H matrix, and/or between the cladding and the U-particles. Other interactions may be expected between the Zr-H matrix and the U-particles. Furthermore, the fuel contains erbium-oxide (Er-O) additions. Interactions can also be expected between the Er-O, the cladding, the Zr-H and the U-particles. The overall result is that very complex interactions may take place as a result of fuel and cladding exposures to high temperatures. This report discusses the characterization of the baseline fuel microstructure in the as-received state (prior to exposure to high temperature), characterization of the fuel after annealing at 950C for 24 hours and the results from diffusion couple experiments carries out at 1000C for 5 and 24 hours. Characterization was carried out via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) with sample preparation via focused ion beam in situ-liftout-technique.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗