Search NASA⌕ Search

SEARCH · Search NASA

Results for “Freeform”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Arbitrary Achromatic Polarization Control with Reconfigurable Metasurface Systems

Abstract Dynamic control over the polarization state of light is foundational for many scientific and technological applications, yet it remains a challenge to dynamically tailor responses with arbitrary polarization bases over a broad bandwidth. Broadband metasurface systems that utilize microscale displacements between two metasurfaces to enable reconfigurable polarization responses within a predefined polarization basis are reported. The metasurface pairs form an interferometer, and the lateral displacements produce detour phase shifts within the interferometer beam paths that mediate polarization state tuning. It is shown how the metasurface systems can be designed using freeform topology optimization to enable tailorable elliptical birefringence responses over a large bandwidth and how cascaded metasurface systems can enable the mapping of input and output polarization states between any two points on the Poincare sphere. It is anticipated that these concepts will have utility in imaging, display, communications, and metrology applications in classical and quantum optical domains.

Wang, Evan W.↗
DOE OSTI2023

Antireflective Multi‐Dielectric Metasurfaces Operating in the Visible

Abstract As increasingly more demanding photonics applications are brought on‐chip, more complex design solutions are employed to deliver enhanced performance: e.g., meta‐molecules, inverse‐designed freeform structures, and multilayer metasurfaces. Instead, this study introduces anti‐reflective metasurfaces fabricated in a single nanolithography step that follows deposition of multiple dielectrics onto a substrate. Anti‐reflective metasurfaces offer fundamentally better transmission efficiencies compared to conventional equivalents. Conventional and anti‐reflective metalenses, both fabricated in the Ta 2 O 5 /SiO 2 material platform for 461 nm operation, show an improvement in focusing efficiencies from ≈ 55% to ≈ 90% at low numerical apertures and from ≈ 35% to ≈ 65% at high numerical apertures. Simulations of ideal and imperfect metalenses indicate that anti‐reflective metasurfaces not only improve transmission at the design library level, but also reduce spurious diffraction and protect against higher‐order scattering.

Optics↗
DOE OSTI2020

Design of additively manufactured methanol conversion reactor for high throughput production

Additively manufactured methanol conversion reactor was designed and fabricated for high throughput fuel production while capturing carbon dioxide. Here, the reactor designed is part of large effort in integrating electrolyzer and catalytic reactor system. Processing in fabricating the steel, titanium, and nickel alloy reactors were optimized to improve the catalyst deposition process and reaction efficiency. Microstructure of the additively manufactured reactors were characterized. General design is utilized to improve the performance of the reactor while exploring the benefit of freeform in additive manufacturing.

08 HYDROGEN↗
DOE OSTI2022

Laser Additive Manufacturing Process Development for Bismuth Telluride Thermoelectric Material

Thermoelectric generators have strong potential for aerospace and aircraft applications. However, traditional manufacturing methods for thermoelectric devices severely limit device adaptability and consequently marketability. Laser powder bed fusion is an additive manufacturing method which shows promising potential for producing thermoelectric devices. Thermoelectric materials pose unique challenges compared to metals because of low thermal conductivity, brittle fracture characteristics, and irregular powder particle morphologies. Herein, we communicate processing procedures to fabricate thermoelectric parts of Bi 2 Te 3 through laser powder bed fusion. In this study, we identify the successful combination of key process parameters—laser power, scan speed, hatch distance, and powder layer thickness—to achieve high-quality parts in terms of density and physical properties, and we demonstrate the impact of process parameter variation on built part quality. While it cannot exclusively determine part quality, the volumetric energy density is a useful guide in deciding process parameters for thermoelectric materials, and the optimal value is between 9 and 11 J/mm 3 for Bi 2 Te 3 . We demonstrate successful fabrication of different freeform geometries of Bi 2 Te 3 powders. The results suggest it is possible to extend this method more broadly to other semiconductor materials, including thermoelectric power generation materials applicable for space applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Frontal Polymerization of Dihydrofuran Comonomer Facilitates Thermoset Deconstruction

Frontal ring-opening metathesis polymerization (FROMP) is a rapid, low-energy manufacturing reaction that is useful for curing thermosetting materials. FROMP of dicyclopentadiene (DCPD) results in poly(dicyclopentadiene) (p(DCPD)), a tough thermoset with excellent mechanical performance and chemical stability. Like most thermosets, p(DCPD) cannot be reprocessed and is therefore difficult to recycle. Previous work demonstrated that the incorporation of a small quantity of cleavable units in the strand segments of p(DCPD) networks enables their deconstruction. Here, we report that a commercially available multifunctional comonomer, 2,3-dihydrofuran (DHF), both acts as a potent Grubbs catalyst inhibitor during FROMP and introduces acid cleavable units. The resulting materials retain high performance characteristics, including glass-transition temperatures ranging from 115 to 165 °C and ultimate strength ranging from 35 to 40 MPa. The addition of DHF above critical loading levels enables deconstructable thermosets. Here, we further demonstrate freeform three-dimensional (3D) printing of deconstructable thermosets via frontal polymerization.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additive manufacturing of carbon fiber-reinforced thermoset composites via in-situ thermal curing

Fiber-reinforced polymer composites are lightweight structural materials widely used in the transportation and energy industries. Current approaches for the manufacture of composites require expensive tooling and long, energy-intensive processing, resulting in a high cost of manufacturing, limited design complexity, and low fabrication rates. Here, we report rapid, scalable, and energy-efficient additive manufacturing of fiber-reinforced thermoset composites, while eliminating the need for tooling or molds. Use of a thermoresponsive thermoset resin as the matrix of composites and localized, remote heating of carbon fiber reinforcements via photothermal conversion enables rapid, in-situ curing of composites without further post-processing. Rapid curing and phase transformation of the matrix thermoset, from a liquid or viscous resin to a rigid polymer, immediately upon deposition by a robotic platform, allows for the high-fidelity, freeform manufacturing of discontinuous and continuous fiber-reinforced composites without using sacrificial support materials. This method is applicable to a variety of industries and will enable rapid and scalable manufacture of composite parts and tooling as well as on-demand repair of composite structures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Inverse-designed metasurfaces with facile fabrication parameters

Abstract Optical metasurfaces are planar nanostructured devices that are industrially attractive in part because they utilize high-throughput microelectronic fabrication techniques for implementation. It is therefore critical to develop design paradigms that can balance the realization of highly efficient wavefront responses together with device manufacturability. We introduce a gradient-based design framework for freeform metasurfaces in which nanoscale elements are explicitly constrained to feature basic shapes, nearly uniform feature sizes, and exceptionally low aspect ratios. In spite of the apparent uniformity of the metasurface geometric features, the devices are able to utilize nonlocal near-field optical coupling to achieve highly efficient and extreme wavefront scattering beyond conventional design methodologies. Utilizing this approach, we design facile high-numerical-aperture devices such as beam deflectors and large-area metalenses capable of diffraction-limited focusing. We anticipate that these concepts can facilitate the design and integration of metasurfaces into monolithic optical systems.

Optics↗
DOE OSTI2025

Virus species names have been standardized; virus names remain unchanged

Virus taxonomy, comprising classification and nomenclature, is regulated by the International Committee on Taxonomy of Viruses (ICTV). Taxon names are standardized to facilitate recognition and communication, with defined suffixes for each rank (e.g., the names of orders, families, and genera end in -virales, -viridae, and -virus, respectively). However, until recently, a standard format for species names was lacking. In 2021, following extensive discussion and community consultation, the ICTV decided to adopt a standardized binomial (Linnaean) format for virus species names, consisting of the genus name followed by a "freeform" species epithet. Previously assigned virus species names that were non-compliant with the binomial format have been fully updated. In contrast to taxon names regulated by the ICTV, the names of viruses, or "common" names, such as yellow fever virus or human immunodeficiency virus, are not under the remit of the ICTV and have not been changed.

Zerbini, F Murilo↗
DOE OSTI2020

Thermal compensation of molded silicone optics

Optical grade silicone has various properties that make it attractive for solar concentrators, such as excellent transmission across the solar spectrum and flexible moldability for freeform profiles. In this study, a glass–silicone lens structure is proposed to reduce the optothermal effect on the silicone lens. Experimental measurements and simulation modeling results demonstrate that the focal length sensitivity of the glass–silicone lens with respect to temperature can be reduced by a factor of 10 when compared to a silicone lens alone. This model has been extended to the simulation of a proposed two-stage silicone solar concentrator, consisting of an array of acylindrical lenslets and rows of waveguides that focus light onto microphotovoltaic cells. The optical efficiency of the solar concentration system showed a change of less than 10% compared to the efficiency at room temperature for temperature changes from − <#comment/> 10 ∘ <#comment/> C to 70°C.

Lyons, Nicholas P.↗
DOE OSTI2021

Effect of workpiece curvature on the tool influence function during hemispherical sub-aperture tool glass polishing

The influence of workpiece curvature on the tool influence function spot during polishing of fused silica glass with cerium oxide slurry, while using a rotating hemispherical pad-foam tool for a wide variety of process conditions (tool displacement, inclination angle, and rotation rate), has been investigated. (Workpiece curvature ranged from 500 mm radius concave to 43 mm radius convex.) The TIF spot decreases in diameter and increases in the peak removal rate on more convex workpieces. In contrast, the TIF spot increases both in diameter and peak removal rate on more concave workpieces. For the range of workpiece curvatures investigated, both the spot size and the peak removal rate changed significantly, as much as 2 times. An elastic sphere–sphere contact mechanics model, which utilizes both a modified displacement (that leads to a change in the applied load) as well as a mismatch factor (that influences the pressure distribution shape), has been developed. Furthermore, the model was validated using both offline load-displacement measurements and finite-element analysis simulations. The model quantitatively describes the measured change in the relative contact diameter and relative pressure distribution, as well as semiquantitively describes the change in the relative volumetric removal rate on a large variety of TIF spots. The change in the volumetric removal rate for convex workpieces is a result of the balance between a decreasing spot size (reducing removal) and an increasing peak pressure (increasing removal), which usually results in relatively small changes in volumetric removal. In the case of concave workpieces, the volumetric removal rate change is also governed by a similar balance, but the spot size increase contribution dominates, resulting in a significant increase in volumetric removal rate. Understanding these trends can enable methods to add greater determinism during the fabrication of freeform optics by adjusting polishing parameters (such as dwell time) while the tool translates along a workpiece surface with different local curvatures.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Understanding the tool influence function during sub-aperture belt-on-wheel glass polishing

The tool influence function (TIF) during sub-aperture belt-on-wheel polishing has been evaluated as a function of various process conditions (belt use/wear, dwell time, displacement, belt velocity, and wheel modulus and diameter) on fused silica glass workpieces using C e O 2 polishing media. TIF spots are circular or elliptical in shape with a largely flat bottom character. Furthermore, the volumetric removal rate varies significantly with belt use (or wear), stabilizing after ~<!-- ~ --> 15 m i n of use. A modified Preston model, where the pressure dependence is adjusted using a different scaling of the wheel modulus ( E w 0.5 ), largely predicts the volumetric removal rate over the range of process conditions evaluated. The relatively high volumetric removal rate of 30 -<!-- - --> 60 m m 3 / h using a fixed C e O 2 -in-resin-host belt offers a rapid, and hence, more economical, initial polish of aspheric and freeform optics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

A review of materials used in tomographic volumetric additive manufacturing

Abstract Volumetric additive manufacturing is a novel fabrication method allowing rapid, freeform, layer-less 3D printing. Analogous to computer tomography (CT), the method projects dynamic light patterns into a rotating vat of photosensitive resin. These light patterns build up a three-dimensional energy dose within the photosensitive resin, solidifying the volume of the desired object within seconds. Departing from established sequential fabrication methods like stereolithography or digital light printing, volumetric additive manufacturing offers new opportunities for the materials that can be used for printing. These include viscous acrylates and elastomers, epoxies (and orthogonal epoxy-acrylate formulations with spatially controlled stiffness) formulations, tunable stiffness thiol-enes and shape memory foams, polymer derived ceramics, silica-nanocomposite based glass, and gelatin-based hydrogels for cell-laden biofabrication. Here we review these materials, highlight the challenges to adapt them to volumetric additive manufacturing, and discuss the perspectives they present. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2021

Seamless Hybrid-integrated Interconnect NEtwork (SHINE)

Large-scale date centers are becoming increasingly limited by the capacity of interconnects due to the rapid increasing power consumption and bandwidth demands driven by the rigorous down scaling of CMOS critical dimensions in according with the Moore’s Law. As a result of the continuing bandwidth scaling, optical interconnects based on parallel optics, where data are simultaneously transmitted along more than one lane, have becoming a preferred interconnected solution over copper cables. To building an efficient optical interconnect system, optical coupling between different elements, such as optical fibers, photonics chips, is a critical step, which is challenging due to the mode mismatch of varies optical ports. In this project, we proposed and demonstrated an optical interfacing scheme, which provided a light coupling approach with low energy loss, broadband operation, high alignment tolerance and compatible with scalable fabrication and testing. Here, the mode transformation is achieved by a total internal reflection from a chip integrated microscale freefrom surface. Due to the enormous light wavefront manipulating ability associated with the gigantic design space, the freeform couplers platform is universally applicable to a wide range of optical coupling scenarios, such as the interfacing between a waveguide to a fiber, another waveguide, surface normal device, or free space.

42 ENGINEERING↗
DOE OSTI2020

Laser gain media fabricated via direct ink writing (DIW) and ceramic processing

A transparent ceramic optic includes: a lasing region comprising at least one lasing species dopant; and a transparent region transparent to light generated by the lasing species. At least the transparent region is doped with at least one other dopant species such that the lasing region and the transparent region are characterized by a difference in refractive index between the two regions in an amount of about 1.0×10−4 or less. Inventive formulations of inks suitable for fabricating transparent ceramic optics having desirable compositional characteristics such as concentration gradients in desired spatial arrangements, e.g. using additive manufacturing techniques such as direct ink writing and/or extrusion freeform fabrication are also disclosed, along with suitable techniques for forming the transparent ceramic optics from such inks.

Payne, Stephen A.↗
DOE OSTI2021

Additive Manufacturing of Lightweight Structures: Microfibrillated Cellulose – PLA Biofoams

Extrusion-based polymer additive manufacturing (AM) technology is growing rapidly. The introduction of fiber reinforced feedstock materials and recent developments in the manufacturing systems have promulgated large scale AM of composites to create new industries and applications. Synthetic fibers such as carbon and glass fibers are commonly used to reinforce polymer composites. However, increasing environmental and long-term sustainability concerns are leading to new materials using cellulose fiber reinforcement in bio-derived polymers. These materials offer new property sets, new supply chains and have the potential to provide economical solutions leading to new applications. Large scale AM can be attractive for many different applications because of its ability to freeform manufacture complex geometries; each application may require different material properties. One of the novel application areas for large scale AM is 3D printing of lightweight materials via foaming. Although achieving low density is the key in light weighting via foaming, mechanical performance is also important for many applications. In this study the impact of micro-cellulose fibers (MFC) on foaming behavior and the mechanical properties of additively manufactured parts is investigated. MFC-polylactic acid (PLA) feedstock pellets were prepared at varying MFC content (5, 10, 15 and 20 wt.%) to understand the impact of cellulose fiber content on density and mechanical properties of the AM biocomposites. Also, the impact of extrusion speed and foaming agent content on the AM biocomposites is investigated. Although achieving uniform printed foam structure is challenging with the presence of cellulose fibers, promising results were accomplished with density values below 0.5g/cm3.

Tekinalp, Halil↗
DOE OSTI2021

Additive manufacturing of power poles using bamboo-polymer composites: A quick solution for power grid restoration

Polymer additive manufacturing (AM) technology is rapidly growing and its transition to become an advanced manufacturing technique now offers possibilities for unconventional applications. One of these potential applications is on site additive manufacturing of power poles. During natural incidents such as storms and hurricanes, power lines can be severely damaged and there may not be sufficient spare power poles to replace. In such situations, additive manufacturing of power poles on site can offer a fast, temporary solution during emergencies. The ability of freeform manufacturing of parts with complex geometries makes large scale AM attractive for various applications; however, due to residual stress build up and need for different mechanical requirements for different applications, reinforcement of the AM feedstock is necessary. In addition to carbon and glass fibers, bio-derived fibers can also be used as a reinforcing phase, both to utilize the natural resources at the emergency area and in terms of long-term sustainability. In this project, design and additive manufacturing of a 13.1 m power pole was demonstrated. Three different feedstock material options (polystyrene, cellulose ester and polycarbonate reinforced with glass and bamboo fibers) and two different pole designs were investigated. As-printed part tensile properties both in printing and interlayer directions were measured and a power pole was printed as six pieces and put together successfully. Finally, a conceptual design of a portable power pole manufacturing approach was proposed.

Tekinalp, Halil↗
DOE OSTI2025

Laser-assisted additive manufacturing

Laser additive manufacturing apparatus, systems, and methods for the fabrication of high quality freeform high value structures. The apparatus, systems, and methods utilize a material powder having varying particle size and shape as raw material. It can also be adopted to use a wire as the feed material.

Demos, Stavros G.↗
DOE OSTI2021

Impact of neutron irradiation on the thermophysical properties of additively manufactured stainless steel and inconel

The deployment of additive manufacturing (AM) technologies to support the nuclear energy industry is limited by the current lack of data related to the irradiation performance of AM parts. The Colorado School of Mines is conducting a multi-year irradiation and post irradiation examination project to study the impacts of neutron irradiation on stainless steel 316L and Inconel 718 and 625 specimens produced by several commercially available AM techniques and irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). This paper presents initial results on the impact of neutron irradiation on the heat capacity, the thermal diffusivity, and the thermal conductivity of the specimens at temperatures between 100 oC and 400 oC. The unirradiated AM specimens have heat capacity values similar to, or lower than, the reference values, regardless of manufacturing method or material. The irradiated AM specimens have average heat capacities greater than the unirradiated specimens and reference values in every case. Additionally, the thermal diffusivities of the unirradiated AM specimens are either larger or statistically similar to the reference values. The irradiated AM specimens exhibit lower thermal diffusivities compared to the reference thermal diffusivity values. One of the stainless steel 316L laser powder bed fusion samples exhibited thermal diffusivity values with statistically significant anisotropy prior to and after irradiation. The thermal conductivities of the unirradiated AM stainless steel 316L specimens and the unirradiated Inconel 718 specimens are lower or statistically similar to the reference values. The unirradiated Inconel 625 specimens exhibit slightly higher thermal conductivity values than the reference values. The irradiated specimens show a significant increase in thermal conductivity compared to the unirradiated specimens and the reference values for all materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗