Search NASA⌕ Search

SEARCH · Search NASA

Results for “II-VI compound”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mid-Infrared Photoluminescence from Tellurium Thin Films

Tellurium is an elemental semiconductor with a 0.34 eV optical band gap, showing promise for mid-infrared (MIR) optoelectronics including light-emitting diodes. However, quantitative measurement of the tellurium luminescence efficiency has not yet been investigated, and growing optically active films remain challenging. Here, we demonstrate the low-temperature growth of bright tellurium thin films by using physical vapor transport. The sample morphology is controlled by varying the growth temperature, yielding continuous thin films, microparticles, or nanowires. Additionally, we demonstrated patterned growth by using a seed layer for selective nucleation. Quantitative photoluminescence measurements at room temperature reveal an internal quantum yield of 2.0% at 0.34 eV for the as-grown tellurium films, comparable to the best-reported efficiencies of III-V and II-VI compound semiconductors with similar band gaps. Furthermore, we demonstrate band-gap tunability with Te-Se alloys, where up to 20% selenium incorporation gradually blue-shifts the band gap to 0.55 eV. The work demonstrates the potential use of tellurium for efficient MIR devices.

Wang, Shu↗
NASA NTRS1969

Carrier injection electroluminescence

Carrier injection luminescence properties useful for display medium applications, discussing group II-VI compounds as injection host crystal materials

Haas, R. W.↗
NASA NTRS1981

Far infrared filters for the Galileo-Jupiter and other missions

Progress in the development of FIR multilayer interference filters for the net flux radiometer and photopolarizing radiometer to be carried on board the Galileo mission to Jupiter is reported. The multilayer interference technique has been extended to the region above 40 microns by the use of PbTe/II-VI materials in hard-coated combination, with the thickest layers composed of CdSe QWOT at 74 microns and PbTe QWOT. Improvements have also been obtained in filters below 20 microns on the basis of the Chebyshev stack design. A composite filter cutting on steeply at 40 microns has been designed which employs a thin crystal quartz substrate, shorter wavelength absorption in ZnS and As2S3 thin films, and supplementary multilayer interference. Finally, absorptive filters have been developed based on II-VI compounds in multilayer combination with KRS-5 (or 6) on a KRS-5 (or 6) substrate

Seeley, J. S.↗
NASA NTRS1989

Electronic structures of HgTe and CdTe surfaces and HgTe/CdTe interfaces

A Green's-function method has been used to study the surface and interface electronic structures of the II-VI compounds HgTe and CdTe. Localized surface and resonance states near the cation-terminated (100) surface of CdTe and the anion-terminated surface of HgTe have been found for the ideal surfaces. The energies and strengths of these surface states are altered by surface perturbations. The bulk states near the surface are drastically modified by the creation of the surface, but the band gaps remain unchanged. Numerical evaluation of the local densities of states at the Gamma and J points shows that, at the (100) interface of HgTe/CdTe, the previously observed surface states are no longer present. However, in the interface region, bulk states of one material penetrate some distance into the other material.

Schick, J. T.↗
NASA NTRS1997

Growth of Bulk Wide Bandgap Semiconductor Crystals and Their Potential Applications

Developments in bulk crystal growth research for electro-optical devices in the Center for Photonic Materials and Devices since its establishment have been reviewed. Purification processes and single crystal growth systems employing physical vapor transport and Bridgman methods were assembled and used to produce high purity and superior quality wide bandgap materials such as heavy metal halides and II-VI compound semiconductors. Comprehensive material characterization techniques have been employed to reveal the optical, electrical and thermodynamic properties of crystals, and the results were used to establish improved material processing procedures. Postgrowth treatments such as passivation, oxidation, chemical etching and metal contacting during the X-ray and gamma-ray device fabrication process have also been investigated and low noise threshold with improved energy resolution has been achieved.

Chen, Kuo-Tong↗
NASA NTRS1982

III-V semiconductor solid solution single crystal growth

The feasibility and desirability of space growth of bulk IR semiconductor crystals for use as substrates for epitaxial IR detector material were researched. A III-V ternary compound (GaInSb) and a II-VI binary compound were considered. Vapor epitaxy and quaternary epitaxy techniques were found to be sufficient to permit the use of ground based binary III-V crystals for all major device applications. Float zoning of CdTe was found to be a potentially successful approach to obtaining high quality substrate material, but further experiments were required.

Gertner, E. R.↗
NASA NTRS1990

Vacancy formation and extraction energies in semiconductor compounds and alloys

A model for calculating the extraction energies and vacancy-formation energies in diamond-cubic and zinc-blende semiconductors is developed on the basis of Harrison's (1980, 1983) tight-binding theory. The extraction energies provide a reference from which other final states of the removed atoms can be calculated. The results of calculations show that, in a given compound, the calculated extraction energies are larger for the anion than for the cation, with the difference between the cation and the anion being larger in the II-VI than in the III-V compounds. This is in agreement with experimental results.

Berding, M. A.↗
NASA NTRS1975

Applied research on 2-6 compound materials for heterojunction solar cells

Several II-VI heterojunctions show promise for photovoltaic conversion of solar energy. The three of greatest interest are p-CdTe/n-CdS, p-CdTe/n-ZnSe, and p-ZnTe/n-CdSe. Several p-CdTe/n-CdS heterojunction cells have been prepared by close spaced transport deposition of p-CdTe on single crystal n-CdS, and by two source vacuum evaporation of n-CdS on single crystal p-CdTe. Both types of cells, in an experimental stage, are quite comparable, exhibiting values of quantum efficiency between 0.5 and 0.9, open circuit voltages between 0.50 and 0.66 V, fill factors between 0.4 and 0.6, and solar efficiencies up to 4 percent. Cells of p-ZnTe/n-CdSe have also been made by close spaced vapor transport deposition of n-CdSe on single crystal p-ZnTe.

Bube, R. H.↗
NASA NTRS1987

Issues in the growth of bulk crystals of infrared materials

Attention is given to the relevant criteria governing materials choice in the growth of IR optoelectronic bulk single crystals of III-V and II-VI alloy and I-III-VI2 compound types. The most important considerations concern the control of crystal purity, microstructural perfection, stoichiometry, and uniformity during crystal growth, as well as the control of surface properties in wafer fabrication. Specific examples are given to illustrate the problems encountered and their preferred solutions.

Bachmann, K. J.↗
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
NASA NTRS1998

Crystal Growth of ZnSe and Related Ternary Compound Semiconductors by Vapor Transport

Interest in optical devices which can operate in the visible spectrum has motivated research interest in the II-VI wide band gap semiconductor materials. The recent challenge for semiconductor opto-electronics is the development of a laser which can operate at short visible wavelengths, In the past several years, major advances in thin film technology such as molecular beam epitaxy and metal organic chemical vapor deposition have demonstrated the applicability of II-VI materials to important devices such as light-emitting diodes, lasers, and ultraviolet detectors.The demonstration of its optical bistable properties in bulk and thin film forms also make ZnSe a possible candidate material for the building blocks of a digital optical computer. Despite this, developments in the crystal growth of bulk II-VI semiconductor materials has not advanced far enough to provide the low price, high quality substrates needed for the thin film growth technology. The electrical and optical properties of semiconductor materials depend on the native point defects, (the deviation from stoichiometry), and the impurity or dopant distribution. To date, the bulk growth of ZnSe substrates has been plagued with problems related to defects such as non-uniform distributions of native defects, impurities and dopants, lattice strain, dislocations, grain boundaries, and second phase inclusions which greatly effect the device performance. In the bulk crystal growth of some technologically important semiconductors, such as ZnTe, CdS, ZnSe and ZnS, vapor growth techniques have significant advantages over melt growth techniques due to the high melting points of these materials.

Su, Ching-Hua↗
NASA NTRS1987

II-VI and I-III-VI2 alloy crystals for photovoltaic applications

The results of the photoreflectance, photoconductivity, and photoluminescence studies on Mn(x)Cd(1-x)Te single crystals are discussed from the viewpoint of the utility of these compounds as gap components in multijunction solar cells. Attention is also given to recent results on CuInSe2 and on quaternary I-III-VI2 alloys based on CuInSe2. Recent Kelvin probe and X-ray photoemission spectroscopy studies of the surface properties of CuInSe2 and Mn(x)Cd(1-x)Te, respectively, are described. In addition, recent results on the radiation damage and annealing kinetics of Mn(x)Cd(1-x)Te are considered in the context of future work on the sputtering and ion beam deposition of thin films of this material.

Bachmann, K. J.↗
NASA NTRS1991

FTIR Spectroscopic Characterization Of II-VI Semiconductors

Combination of commercial Fourier-transform infrared (FTIR) spectrometer with computer and special-purpose software constitutes highly automated facility for acquisition and processing of infrared transmission or reflection spectral image data. Intended principally to acquire transmission spectra of some compounds of elements in groups II and VI of periodic table. System used to characterize specimens of II/VI alloy semiconductors grown by directional solidification and quenching. Transmission-edge maps helpful in studies of flows, gradients of temperature, and coefficients of diffusion in solidifying melts. Data acquired by system include optical characteristics, and they both verify and complement data obtained by such other techniques as measurements of density and x-ray-dispersion analysis.

Perry, G. L. E.↗
DOE OSTI2024

Impacts of Non-Ideal Back Contact on Capacitance Measurements in CdTe Solar Cells

CdTe solar cells suffer from a non-ideal back contact which can strongly affect the equivalent circuit model and complicate capacitance measurements. Here, five different back contact materials are deposited on identical CdTe absorbers and their influence on capacitance measurements is characterized. A five-element equivalent circuit model is shown to represent a CdTe solar cell with a non-ideal back contact, and capacitance-frequency (C-f) measurements on each sample clearly show the influence of this contact. Capacitance-voltage (C-V) measurements on each sample show the influence of frequency on measured capacitance. In the AlGaOx/Au sample, temperature dependent C-fs show the back barrier height to be 240 meV, and ongoing measurements will give a comparison of back barrier heights for all samples. This study provides insight into the efficacy of various back contacts and highlights potential errors in the interpretation of capacitance measurements due to the presence of the back contact.

cadmium compounds↗
NASA NTRS1979

Phase transitions in Group III-V and II-VI semiconductors at high pressure

The structures and transition pressures of Group III-V and II-VI semiconductors and of a pseudobinary system (Ga/x/In/1-x/Sb) have been investigated. Results indicate that GaP, InSb, GaSb, GaAs and possible AlP assume Metallic structures at high pressures; a tetragonal, beta-Sn-like structure is adopted by only InSb and GaSb. The rocksalt phase is preferred in InP, InAs, AlSb, ZnO and ZnS. The model of Van Vechten (1973) gives transition pressures which are in good agreement with measured values, but must be refined to account for the occurrence of the ionic rocksalt structure in some compounds. In addition, discrepancies between the theoretical scaling values for volume changes at the semiconductor-to-metal transitions are observed.

Yu, S. C.↗
DOE OSTI2025

Spatial variation of the low-temperature micro-photoluminescence of THM-grown CdZnTeSe

The quaternary compound CdZnTeSe (CZTS) has emerged as a next-generation detector material. Unlike CdZnTe (CZT), CZTS has the distinct advantages of little or no sub-grain boundary networks and a much lower concentration of Te inclusions, plus better compositional homogeneity. Thus, the material is expected to offer better spatial charge-transport homogeneity compared to CZT. However, an inhomogeneous distribution of point defects in both CZT and CZTS, such as Cd vacancies and residual impurities, can impose additional spatial inhomogeneity of the resistivity, carrier mobilities, and carrier lifetimes of the material. To investigate the spatial distribution of such defects in CZTS, low-temperature photoluminescence (PL) spectroscopic studies were performed at different positions along a single crystalline CZTS sample surface, which was grown by the traveling heater method (THM). In conclusion, the intensity variation of the PL emission of excitons bound to a neutral acceptor defect (A 0 , X), which is likely dominated by an acceptor like Cu-related level, with respect to the PL emission line from a neutral donor-bound exciton (D 0 , X) exhibited significant spatial variation, while the peak energy positions were approximately uniform due to the high compositional and bandgap homogeneity of the material.

II-VI semiconductor↗