Search NASA⌕ Search

SEARCH · Search NASA

Results for “LITHIUM ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A Holistic Stabilization of the Anode in Lithium‐Sulfur Batteries Through a Ternary Alloy Fusion

The anode in lithium–sulfur batteries (LSBs) is plagued by not only inhomogeneous lithium (Li) deposition, but also by parasitic side-reactions. Often, a thick anode (∼400 µm) is used to compensate for these drawbacks, lowering gravimetric and volumetric energy densities. In this work, we demonstrate a ternary alloy anode fabricated via scalable thermal fusion of Li with aluminum (Al) and tellurium (Te) to cohesively address these issues. The Al–Li skeleton serves to homogenize Li deposition as well as reinforce the anode, allowing it to be rolled down to low thicknesses. Te incorporation suppresses the reaction of Li with polysulfides (Li 2 Sn) to form lithium sulfide (Li 2 S) and electrolyte degradation. It can also facilitate the formation of polytellurosulfides (Li 2 Te x Sy), which are far more conducive to Li + -ion diffusion. Even under a lean electrolyte/sulfur (E/S) ratio of 8 µL mg −1 and a low negative/positive (N/P) ratio of 3, capacities over 900 mA h g −1 at a C/5 rate are obtained in cells with Li–Te–Al anodes with a capacity retention of 80% after 70 cycles. In comparison, the baseline lithium-metal anode retains only 35% after 50 cycles. Furthermore, the Li–Te–Al anodes confer a 24% boost to gravimetric energy density at the pouch cell level.

25 ENERGY STORAGE↗
DOE OSTI2025

The Origin of Improved Performance in Boron‐Alloyed Silicon Nanoparticle‐Based Anodes for Lithium‐Ion Batteries

Stabilizing the solid electrolyte interphase (SEI) remains a key challenge for silicon‐based lithium‐ion battery anodes. Alloying silicon with secondary elements like boron has emerged as a promising strategy to improve the cycle life of silicon anodes, yet the underlying mechanism remains unclear. To address this knowledge gap, how boron concentration influences battery performance is systematically investigated. These results show a near‐monotonic increase in cycle lifetime with higher boron content, with boron‐rich electrodes significantly outperforming pure silicon. Additionally, silicon‐boron alloy anodes exhibit nearly three times longer calendar life than pure silicon. Through detailed mechanistic analysis, alternative contributing factors are systematically ruled out, and it is proposed that improved passivation arises from a strong permanent dipole at the nanoparticle surface. This dipole, formed by undercoordinated and highly Lewis acidic boron, creates a static, ion‐dense layer that stabilizes the electrochemical interface, reducing parasitic electrolyte decomposition and enhancing long‐term stability. These findings suggest that, within the SEI framework, the electric double layer is an important consideration in surface passivation. This insight provides an underexplored parameter space for optimizing silicon anodes in next‐generation lithium‐ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Alloying Interlayers for Anode‐Less Lithium‐Metal Polymer Batteries

Anode‐less lithium‐metal batteries potentially offer further increased energy densities. However, the Coulombic efficiency (CE) of lithium plating and stripping, as a classical measure of Li inventory reversibility, is commonly still insufficient for achieving long‐lasting rechargeable batteries. Herein, the potential benefits of employing thin (20 nm) metal interlayers of Ag, Pt, and Au on Cu to alloy with Li in Cu||Li half‐cells and induce homogeneous Li plating with poly(ethylene oxide)‐based electrolytes are investigated. Interestingly, not all alloying interlayers enable a higher CE compared to neat Cu foil with 84%—specifically Ag@Cu with only 81%, while the best performing one, Au@Cu, provides a substantially increased CE of 91%. While generally the formation of “dead lithium” is found to be the major source of CE, this appears to be less pronounced in the case of Au@Cu, indeed. Further improvement can be achieved by carefully adjusting the cell voltage to a region in which the continuous de‐/alloying is suppressed, yielding a further enhanced CE of 94%, thus highlighting the need for a comprehensive approach to design suitable electrode chemistries and designs beyond a “simple” material improvement.

anode-less battery↗
DOE OSTI2020

Exploration of Sn 70 Li 30 alloy as possible material for flowing liquid metal plasma facing components

As an advanced alternative to solid materials, Liquid Metals (LM) may offer more resilient and feasible Plasma Facing Components (PFCs). Particularly, regarding the unavoidable material erosion/degradation produced by particle/heat fluxes in future fusion devices where much longer duty cycles are expected. Furthermore, configurations that propose a flowing LM surface can add the advantage of a continuously fresh and clean layer facing the plasma. Although lithium is the most widely tested option, tin-lithium (SnLi) alloys have been proposed to attempt to combine the positive characteristics of both pure elements and ameliorate the specific issues of lithium. In this work, the potential use of Sn70Li30 alloy in such flowing concepts has been explored by addressing several preliminary and mandatory aspects for its utilization. Key issues such as wettability and compatibility of the alloy with relevant substrates have been studied in a multidisciplinary approach. The data obtained from deposited liquid tin-lithium droplets indicates approximate wetting temperatures of 360 °C, 390 °C and 405 °C for the fresh alloy on 316 stainless steel, molybdenum, and tungsten, respectively. However, the alloy contamination appeared to strongly affect the wetting characteristics of materials, increasing their wetting temperature by ~130 °C in the worst observed cases. Interestingly, in some instances, the instability of the liquid alloy surface was observed in the form of sudden gaseous ejection. The deposited droplets were posteriorly characterized in terms of absolute composition and depth profile by Inductively Coupled PlasmaOptical Emission Spectroscopy (ICP-OES) and Secondary Ion Mass Spectrometry (SIMS-ToF). Additionally, the nature and composition of the boundaries between the substrates and alloy microparticles was investigated by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), and 3D Laser microscopy. The overall results of this post-mortem characterization revealed that first signs of corrosion induced by both alloy elements (lithium-chromium association and iron-tin intermetallic mixing) were present on 316 stainless steel after short exposures (≤3 h) at temperatures lower than 550 °C. Conversely, molybdenum and tungsten showed good compatibility with the alloy in equivalent conditions. The global implications of these results are finally addressed, focusing on the future perspectives and the more viable scenarios for the eventual utilization of these alloys in flowing liquid metal configurations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Lessons Learned—Lithium Silicide Hydration Fire

Alkali metals, such as lithium, sodium, potassium, etc., are highly reactive elements. While researchers generally handle these metals with caution, less caution is taken when these elements have been “reacted”. In this work, a recent incident is examined in which a pair of researchers ignited a lithium silicide alloy sample that was assumed to be fully hydrated to lithium hydroxide and, thereby, no longer water-reactive. However, variations in the original chemical composition of the lithium compounds examined resulted in select mixtures failing to hydrate and react completely to lithium hydroxide in the time frame allowed. This gave rise to residual unreacted, water-sensitive lithium silicide which resulted in a violent exothermic reaction with water and autoignition of the produced hydrogen gas. This Article describes this incident and improvements that can be implemented to prevent similar incidents from occurring.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Mitigating Interfacial Mismatch between Lithium Metal and Garnet-Type Solid Electrolyte by Depositing Metal Nitride Lithiophilic Interlayer

Solid-state lithium batteries are generally considered as the next-generation battery technology that benefits from inherent nonflammable solid electrolytes and safe harnessing of high-capacity lithium metal. Among various solid-electrolyte candidates, cubic garnet-type Li 7 La 3 Zr 2 O 12 ceramics hold superiority due to their high ionic conductivity (10 –3 to 10 –4 S cm -1 ) and good chemical stability against lithium metal. However, practical deployment of solid-state batteries based on such garnet-type materials has been constrained by poor interfacing between lithium and garnet that displays high impedance and uneven current distribution. Herein, we propose a facile and effective strategy to significantly reduce this interfacial mismatch by modifying the surface of such garnet-type solid electrolyte with a thin layer of silicon nitride (Si 3 N 4 ). This interfacial layer ensures an intimate contact with lithium due to its lithiophilic nature and formation of an intermediate lithium–metal alloy. The interfacial resistance experiences an exponential drop from 1197 to 84.5 Ω cm 2 . Lithium symmetrical cells with Si 3 N 4 -modified garnet exhibited low overpotential and long-term stable plating/stripping cycles at room temperature compared to bare garnet. Furthermore, a hybrid solid-state battery with Si 3 N 4 -modified garnet sandwiched between lithium metal anode and LiFePO 4 cathode was demonstrated to operate with high cycling efficiency, excellent rate capability, and good electrochemical stability. This work represents a significant advancement toward use of garnet solid electrolytes in lithium metal batteries for the next-generation energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2020

Understanding Stabilization in Nanoporous Intermetallic Alloy Anodes for Li-Ion Batteries Using Operando Transmission X-ray Microscopy

Tin-based alloying anodes are exciting due to their high energy density. Unfortunately, these materials pulverize after repetitive cycling due to the large volume expansion during lithiation and delithiation; both nanostructuring and intermetallic formation can help alleviate this structural damage. Here, these ideas are combined in nanoporous antimony–tin (NP-SbSn) powders, synthesized by a simple and scalable selective-etching method. The NP-SbSn exhibits bimodal porosity that facilitates electrolyte diffusion; those void spaces, combined with the presence of two metals that alloy with lithium at different potentials, further provide a buffer against volume change. This stabilizes the structure to give NP-SbSn good cycle life (595 mAh/g after 100 cycles with 93% capacity retention). Operando transmission X-ray microscopy (TXM) showed that during cycling NP-SbSn expands by only 60% in area and then contracts back nearly to its original size with no physical disintegration. The pores shrink during lithiation as the pore walls expand into the pore space and then relax back to their initial size during delithiation with almost no degradation. Importantly, the pores remained open even in the fully lithiated state, and structures are in good physical condition after the 36th cycle. The results of this work should thus be useful for designing nanoscale structures in alloying anodes.

25 ENERGY STORAGE↗
DOE OSTI2026

Minimizing Interfacial Resistance between Polymer Electrolytes and Metal Electrodes Using Applied Current

Reducing the interfacial resistance between different phases in electrochemical systems is crucial for enabling practical applications. In this work, we proposed a process for reducing the interfacial resistance between polymer electrolytes and metal electrodes. Thus far in the literature, the lowest interfacial resistance reported in these systems is 15 Ω·cm2. In this study, assembled and preconditioned symmetric cells with lithium–indium alloy electrodes showed similar values. The current through the cell was increased in steps up to the limiting current. This resulted in a permanent decrease of the interfacial resistance to values as low as 1 Ω·cm2, a value that is comparable to that of optimized lithium-ion batteries. The proposed process is general, and it could be applied to any combination of polymer electrolytes and metal electrodes.

Lee, Jaeyong↗
DOE OSTI2022

Fast and Simple Ag/Cu Ion Exchange on Cu Foil for Anode-Free Lithium-Metal Batteries

Lithium-metal batteries with zero excess lithium on the anode side paired with a fully lithiated cathode are regarded as a form of the highest energy-density configuration. Unfortunately, the continuous lithium loss over cycling from a limited amount of lithium reservoir significantly degrades the overall cell performance in the anode-free system. To mitigate the deterioration, modifying the current collector for enhanced lithium cycling is an indispensable route. Here, we apply a Ag/Cu ion exchange to precipitate micro-sized Ag particles on the Cu current collector to enhance the lithium reversibility via (de)alloying process. Further, we show a smoother morphology of lithium upon alloying, which leads to a lowered nucleation potential as well as increased average Coulombic efficiency in Li||Cu cells regardless of electrolyte formulation. The preferred lithium adsorption on Ag and AgLi over Cu is demonstrated with density functional theory calculations, which supports that Li is forming a gamma-phase alloy in the last stage rather than being deposited beneath the alloy. Lastly, this simple Cu foil modification enhances lithium reversibility and reduces its nucleation barrier, thus mitigating the capacity fade of a Cu||LiFePO 4 with reduced polarization.

25 ENERGY STORAGE↗
DOE OSTI2024

High voltage electrolytes for lithium-ion batteries with micro-sized silicon anodes

Abstract Micro-sized silicon anodes can significantly increase the energy density of lithium-ion batteries with low cost. However, the large silicon volume changes during cycling cause cracks for both organic-inorganic interphases and silicon particles. The liquid electrolytes further penetrate the cracked silicon particles and reform the interphases, resulting in huge electrode swelling and quick capacity decay. Here we resolve these challenges by designing a high-voltage electrolyte that forms silicon-phobic interphases with weak bonding to lithium-silicon alloys. The designed electrolyte enables micro-sized silicon anodes (5 µm, 4.1 mAh cm −2 ) to achieve a Coulombic efficiency of 99.8% and capacity of 2175 mAh g −1 for >250 cycles and enable 100 mAh LiNi 0.8 Co 0.15 Al 0.05 O 2 pouch full cells to deliver a high capacity of 172 mAh g −1 for 120 cycles with Coulombic efficiency of >99.9%. The high-voltage electrolytes that are capable of forming silicon-phobic interphases pave new ways for the commercialization of lithium-ion batteries using micro-sized silicon anodes.

25 ENERGY STORAGE↗
DOE OSTI2019

Boosting Superior Lithium Storage Performance of Alloy-Based Anode Materials via Ultraconformal Sb Coating–Derived Favorable Solid-Electrolyte Interphase

Alloy materials such as Si and Ge are attractive as high-capacity anodes for rechargeable batteries, but such anodes undergo severe capacity degradation during discharge-charge processes. Compared to the over-emphasized efforts on the electrode structure design to mitigate the volume changes, understanding and engineering of the solid-electrolyte interphase (SEI) are significantly lacking. This work demonstrates that modifying the surface of alloy-based anode materials by building an ultraconformal layer of Sb can significantly enhance their structural and interfacial stability during cycling. Combined experimental and theoretical studies consistently reveal that the ultraconformal Sb layer is dynamically converted to Li 3 Sb during cycling, which can selectively adsorb and catalytically decompose electrolyte additives to form a robust, thin, and dense LiF-dominated SEI, and simultaneously restrain the decomposition of electrolyte solvents. Hence, the Sb-coated porous Ge electrode delivers much higher initial Coulombic efficiency of 85% and higher reversible capacity of 1046 mAh g -1 after 200 cycles at 500 mA g -1 , compared to only 72% and 170 mAh g -1 for bare porous Ge. The present finding has indicated that tailoring surface structures of electrode materials is an appealing approach to construct a robust SEI and achieve long-term cycling stability for alloy-based anode materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Prediction of PbLi fluid flow and temperature field in a thermal convection loop for qualification of fusion materials

Two modeling tools, a thermohydraulics code and a computational model in COMSOL Multiphysics, have been developed, tested and then applied to the analysis of fluid flow and heat transfer in a thermal convection loop (TCL). Such a device has recently been used to experimentally evaluate corrosion compatibility of APMT (Fe–21Cr–5Al–3Mo) steel with high-temperature molten eutectic lead-lithium (PbLi) alloy at Oak Ridge National Lab, TN, USA. Here, the 1-D thermohydraulics code allows for rapid calculations of the loop parameters as a function of the applied heat flux. The supplemental COMSOL finite-element computations provide detailed 3-D velocity and temperature field data but are much more time consuming. Both modelling tools demonstrate an excellent agreement in the computed circulation velocity as well as maximum and minimum temperatures. The performed TCL analysis focuses on flow development in the “hot” and “cold” legs, formation of Dean vortices in corner regions, blocking effect of the immersed samples, and radiative and convective cooling effects under the experiment-relevant conditions for Prandtl number Pr = 0.015, Grashof numbers Gr ~10 7 , and Reynolds numbers Re ~10 4 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tracking Spatiotemporal Electric Potential in Batteries Using High-Resolution Operando X‑ray Transmission Imaging

The formation of significant concentration gradients across electrolytes in batteries affects the rate at which electrochemical reactions occur. In this work, we use high-resolution operando X-ray transmission imaging to capture spatiotemporal salt concentration profiles c(x,t) in a symmetric cell comprising a polymer electrolyte sandwiched between two lithium–indium alloy electrodes during a constant-current experiment followed by open-circuit relaxation. The decay of open-circuit potential is related to the concentration dependence of the potential across concentration cells, U. We show how operando c(x,t) data can be used to calculate the spatiotemporal electric potential “inside” the polarized electrolyte. We track the spatial- and time-dependent cell potential during the constant-current step and distinguish its two contributions: a concentration overpotential governed by U. and an ohmic contribution governed by ionic conductivity. Over most of the time window, the concentration overpotential dominates. At steady state, it is a factor of 7 larger than the ohmic contribution. Such findings indicate that efforts to design new polymer electrolytes should focus on minimizing concentration gradients.

Electrical conductivity↗
DOE OSTI2022

Review of Direct Neutron Conversion and Detection Processes

Commercial and laboratory neutron detection systems use indirect neutron response of materials like pressurized helium-3 (via nuclear reaction 3He(n, p)3H) to measure and count neutrons emanating from a source. Recently a host of semiconductors, especially a ternary semiconductor of lithium indium diselenide (6LiInSe2) and a quaternary alloy of enriched lithium-6, indium, phosphorous, and selenium (6LiInP2Se6), have shown promising neutron counting possibilities by directly converting neutrons into charge-carrying elements within the body of the semiconductor. These semiconductors have high thermal neutron capture cross sections, suitable energy bandgaps (~2.0 electron volts) for room-temperature operations, and a favorable electronic band structure for efficient electron charge transport. The article examines the semiconductor properties of these compounds in terms of their neutron counting capabilities and possible ways to extract neutron energy information from them. Lithium-6 and boron-10 (with thermal neutron absorption cross sections of 938 ± 6 and 3855 ± 26 barns, respectively) produce charged particles to be measured via indirect neutron interactions. The efficiency of indirect conversion neutron detectors is limited because of the inefficiencies in conversion mechanism. In case of direct conversion, the neutrons create charged particles in a single material for neutron capture and charge collection, increasing detection efficiency. Unlike 3He proportional counters, which provide no neutron energy information, the semiconductors can be used as neutron energy spectrometer. Fully resolved neutron energy by 6LiInP2Se6 from a plutonium-beryllium source has been reported in the literature. We will discuss the influence of these multilayered semiconductors’ crystallographic structures and growth techniques on neutron energy determination.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2020

Fast-Charging and Ultrahigh-Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm -2 ) and small areal capacity (<5 mAh cm -2 ), which essentially limits their high-power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low-cost Si wafers are used and are chemically etched down to 20-30 mu m membranes. Simply laminating a Si membrane onto Li foil results in the formation of LixSi alloy film fused onto Li metal with mechanical robustness and high Li-ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm -2 and unprecedented areal capacity up to 100 mAh cm -2 . Furthermore, the surface alloyed Li anode is paired with amorphous MoS 3 cathode and achieves remarkable full-cell performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Corrosion characteristics of Mo and TZM alloy for plasma facing components in molten lithium at 623 K

Here, in this study, the corrosion behaviours of molybdenum (Mo) and a Mo-based alloy (TZM) were investigated using a static immersion corrosion technique. Weight loss, surface microstructure, and corrosion depth of Mo and the TZM alloy were correlated with elements. The compatibility of Mo and the TZM alloy in static liquid Li was suitable. Mo demonstrated uniform corrosion with a homogenous dissolution of free C and Mo, and TZM alloy exhibited a nonuniform corrosion behaviour with a preferential grain boundary attack caused by the selective dissolution of free C, Ti, and Zr. When the surface oxidation layer of the samples was consumed, free C from Mo and TZM diffused into molten Li to form Li 2 C 2 and then was captured by Zr, Ti, and Mo to form thermodynamically stable carbides, which resulted in the enrichment of the C layer near the sample surfaces. In addition, Ti and Zr acted as N-trappers in liquid Li; the formation of Zr and Ti nitrides resulted in the enrichment of N, Ti, and Zr elements on the surface and led to TZM corrosion increase. Thus, Zr and Ti depletion, pitting, and grain boundary corrosion were problematic for TZM under long-term exposure to liquid Li. Reducing the content of free C and nonmetallic N and increasing the amount of Ti and Zr carbides on the surface of and inside the raw TZM alloy helped improve the corrosion resistance of TZM in liquid Li.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Identifying Hidden Li–Si–O Phases for Lithium‐Ion Batteries via First‐Principle Thermodynamic Calculations

SiO–based materials are promising alloys and conversion‐type anode materials for lithium‐ion batteries and are recently found to be excellent dendrite‐proof layers for lithium‐metal batteries. However, only a small fraction of the Li–Si–O compositional space has been reported, significantly impeding the understanding of the phase transition mechanisms and the rational design of these materials both as anodes and as protection layers for lithium‐metal anodes. Herein, we identify three new thermodynamically stable phases within the Li–Si–O ternary system (Li 2 SiO 5 , Li 4 SiO 6, and Li 4 SiO 8 ) in addition to the existing records via first‐principle calculations. The electronic structure simulation shows that Li 2 SiO 5 and Li 4 SiO 8 phases are metallic in nature, ensuring high electronic conductivity required as electrodes. Moduli calculations demonstrate that the mechanical strength of Li–Si–O phases is much higher than that of lithium metal. The diffusion barriers of interstitial Li range from 0.1 to 0.6 eV and the interstitial Li hopping serves as the dominating diffusion mechanism in the Li–Si–O ternary systems compared with vacancy diffusion. These findings provide a new strategy for future discovery of improved alloying anodes for lithium‐ion batteries and offer important insight towards the understanding of the phase transformation mechanism of alloy‐type protection layers on lithium‐metal anodes.

Qu, Jiale↗
DOE OSTI2020

Electrolyte design for LiF-rich solid–electrolyte interfaces to enable high-performance microsized alloy anodes for batteries

Lithium batteries with Si, Al or Bi microsized (>10 µm) particle anodes promise a high capacity, ease of production, low cost and low environmental impact, yet they suffer from fast degradation and a low Coulombic efficiency. In this paper, we demonstrate that a rationally designed electrolyte (2.0 M LiPF 6 in 1:1 v/v mixture of tetrahydrofuran and 2-methyltetrahydrofuran) enables 100 cycles of full cells that contain microsized Si, Al and Bi anodes with commercial LiFePO 4 and LiNi 0.8 Co 0.15 Al 0.05 O 2 cathodes. Alloy anodes with areal capacities of more than 2.5 mAh cm -2 achieved >300 cycles with a high initial Coulombic efficiency of >90% and average Coulombic efficiency of >99.9%. These improvements are facilitated by the formation of a high-modulus LiF–organic bilayer interphase, in which LiF possesses a high interfacial energy with the alloy anode to accommodate plastic deformation of the lithiated alloy during cycling. Lastly, this work provides a simple yet practical solution to current battery technology without any binder modification or special fabrication methods.

25 ENERGY STORAGE↗