SEARCH · Search NASA
Results for “Liquid printing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
On the effect of strain rate during the cyclic compressive loading of liquid crystal elastomers and their 3D printed lattices
Nematic liquid crystal elastomers (LCEs) are a unique class of network polymers with the potential for enhanced mechanical energy absorption and dissipation capacity over conventional network polymers because they exhibit both conventional viscoelastic behavior and soft-elastic behavior (nematic director changes under shear loading). This additional inelastic mechanism makes them appealing as candidate damping materials in a variety of applications from vibration to impact. The lattice structures made from the LCEs provide further mechanical energy absorption and dissipation capacity associated with packing out the porosity under compressive loading. Understanding the extent of mechanical energy absorption, which is the work per unit mass (or volume) absorbed during loading, versus dissipation, which is the work per unit mass (or volume) dissipated during a loading cycle, requires measurement of both loading and unloading response. Here, in this study, a bench-top linear actuator was employed to characterize the loading-unloading compressive response of polydomain and monodomain LCE polymers and polydomain LCE lattice structures with two different porosities (nominally, 62% and 85%) at both low and intermediate strain rates at room temperature. As a reference material, a bisphenol-A (BPA) polymer with a similar glass transition temperature (9 °C) as the nematic LCE (4 °C) was also characterized at the same conditions for comparing to the LCE polymers. Based on the loading-unloading stress-strain curves, the energy absorption and dissipation for each material at different strain rates (0.001, 0.1, 1, 10 and 90 s -1 ) were calculated with considerations of maximum stress and material mass/density. The strain-rate effect on the mechanical response and energy absorption and dissipation behaviors was determined. The energy dissipation ratio was also calculated from the resultant loading and unloading stress-strain curves. All five materials showed significant but different strain rate effects on energy dissipation ratio. The solid LCE and BPA materials showed greater energy dissipation capabilities at both low (0.001 s -1 ) and high (above 1 s -1 ) strain rates, but not at the strain rates in between. The polydomain LCE lattice structure showed superior energy dissipation performance compared with the solid polymers especially at high strain rates.
Visualizing Assembly Dynamics of All‐Liquid 3D Architectures
Abstract To better exploit all‐liquid 3D architectures, it is essential to understand dynamic processes that occur during printing one liquid in a second immiscible liquid. Here, the interfacial assembly and transition of 5,10,15,20‐tetrakis(4‐sulfonatophenyl) porphyrin (H 6 TPPS) over time provides an opportunity to monitor the interfacial behavior of nanoparticle surfactants (NPSs) during all‐liquid printing. The formation of J‐aggregates of H 4 TPPS 2− at the interface and the interfacial conversion of the J‐aggregates of H 4 TPPS 2− to H‐aggregates of H 2 TPPS 4− is demonstrated by interfacial rheology and in situ atomic force microscopy. Equally important are the chromogenic changes that are characteristic of the state of aggregation, where J‐aggregates are green in color and H‐aggregates are red in color. In all‐liquid 3D printed structures, the conversion in the aggregate state with time is reflected in a spatially varying change in the color, providing a simple, direct means of assessing the aggregation state of the molecules and the mechanical properties of the assemblies, linking a macroscopic observable (color) to mechanical properties.
3D Printed Microfluidic Supported Liquid Membrane Module for Radionuclide Separations
Microfluidic supported liquid membrane extraction is a promising technique for microliter-scale radionuclide separations because it requires very small reagent volumes and combines extraction and stripping in a single unit operation. Flat sheet supported liquid membrane (FS-SLM) modules with 100, 200, 300, and 400 μm deep channels were fabricated at a cost of less than 5 USD in material using a commercially available resin three-dimensional (3D) printer. The performance of these modules was characterized by quantifying uranium transport across a 15 v/v% tributyl phosphate (TBP) liquid membrane at flow rates between 5 and 60 μL min –1 and developing a two-dimensional (2D) numerical transport model for the system. The extent of uranium extraction was found to increase with increasing residence time and decreasing channel depth, with quantitative extraction occurring at the slowest flow rates and shallowest channel depths. The numerical model agreed well with the experimental extraction results. Time-dependent calculations showed that the modules reach steady state in fewer than 9 min and that there is a considerable buildup of uranium in the membrane during that time.
Direct Functionalization of Established 3D-Printed Aza-Michael Liquid Crystal Elastomers with Donor–Acceptor Stenhouse Adducts
Extrusion 3D printing has advanced the manufacturing of complex liquid crystal elastomer (LCE) architectures. In parallel, donor–acceptor Stenhouse adducts (DASAs), a class of white-light-responsive photoswitches, have enabled both photochemical and photothermal LCE actuation. However, DASA–LCEs have yet to be extruded and 3D-printed. Two key challenges exist: DASA’s inherent sensitivity to heat and radicals can lead to degradation during ink preparation and printing, and small changes in the concentration of the added DASA component impact the properties of the extrudable ink, requiring reoptimization of well-established 3D-printing protocols. To overcome these challenges, we present a post-printing functionalization strategy that circumvents these limitations. Residual secondary amines, inherent to inks synthesized via standard aza-Michael addition, serve as active sites for covalent attachment of DASA photoresponsive groups following printing and cross-linking. Our method means that DASAs can be directly grafted onto 3D-printed aza-Michael LCEs without modifying the ink formulation or processing. The resulting DASA–LCEs exhibit wavelength tunability within the visible range and a variety of photothermal and photochemical responses. The post-functionalization can occur within 2 min and enables spatial control of the DASA concentration, producing films with tunable color gradients and locally varied photothermal and photochemical responses under visible light. In conclusion, this approach enables the rapid fabrication of DASA-based light-responsive LCEs using established ink formulations with the potential for the design of complex 3D architectures.
A combined numerical and experimental study to elucidate primary breakup dynamics in liquid metal droplet-on-demand printing
Droplet-on-demand liquid metal jetting is emerging as a powerful technology for the additive manufacturing of metallic parts. The success of this method hinges on overcoming several technological challenges. Additionally, the principal one among these challenges is the controlled repeatable ejection of single uniform droplets. Due to the high density and surface tension of liquid metals, the droplet ejection process occurs near the minimal extremes of the printability phase diagram, defined by acceptable ranges for the Weber (We) and Ohnesorge (Oh) numbers. In this work, we experimentally demonstrate the satellite-free ejection of pneumatically actuated molten tin droplets in this extreme corner of printability and use a combination of high-speed video analysis and volume-of-fluid modeling to elucidate the droplet dynamics. While the simulations at low Oh and We can correctly describe several aspects of the breakup process, such as an increasing tail and pinch-point near the nozzle, no single parameter set can completely capture the droplet shape at breakup. Instead, the experimental droplet dynamics appear to include features from both high and low Oh breakup. This disagreement is ascribed to the incomplete description of the droplet ejection process including wetting and exit effects near the nozzle opening and surface effects such as transient cooling and oxide formation.
Digital Light Process 3D Printing of Magnetically Aligned Liquid Crystalline Elastomer Free–forms
Liquid crystalline elastomers (LCEs) are anisotropic soft materials capable of large dimensional changes when subjected to a stimulus. The magnitude and directionality of the stimuli-induced thermomechanical response is associated with the alignment of the LCE. Recent reports detail the preparation of LCEs by additive manufacturing (AM) techniques, predominately using direct ink write printing. Another AM technique, digital light process (DLP) 3D printing, has generated significant interest as it affords LCE free-forms with high fidelity and resolution. However, one challenge of printing LCEs using vat polymerization methods such as DLP is enforcing alignment. Here, we document the preparation of aligned, main-chain LCEs via DLP 3D printing using a 100 mT magnetic field. Systematic examination isolates the contribution of magnetic field strength, alignment time, and build layer thickness on the degree of orientation in 3D printed LCEs. Informed by this fundamental understanding, DLP is used to print complex LCE free-forms with through-thickness variation in both spatial orientations. Further, the hierarchical variation in spatial orientation within LCE free-forms is used to produce objects that exhibit mechanical instabilities upon heating. DLP printing of aligned LCEs opens new opportunities to fabricate stimuli-responsive materials in form factors optimized for functional use in soft robotics and energy absorption.
Mass transfer intensification through increased surface wetting and liquid turbulence using 3D printing structured packing for CO2 capture
The absorber column is one of the most expensive pieces of equipment to construct in the solvent-based post-combustion carbon capture unit. In order to decrease the absorber size and reduce capital costs, novel polymer packings were proposed by enhancing surface wettability and local turbulence within liquid solvent. The novel packings intensify the mass transfer in CO2 absorption and show better separation efficiency than traditional structured packings. In this work, the economic influence of applying the more efficient packing with a shorter absorber column is studied in a techno-economic analysis for a carbon capture unit at a coal-fired power plant. The baseline case includes CO2 capture unit in a supercritical pulverized coal power plant to generate 650 MWe (net) of electricity, where the additional CO2 capture unit leads to 63.4% increase of LCOE. While implementing UK PCC with traditional and novel packings, there will be 47.2% and 46.4% LCOE increase separately, both of which are lower than the baseline value. Applying more efficient packing and smaller absorber could further lessen the LCOE increase. The UK PCC with traditional packings reduces CO2 capture cost by 23.4% and the application of the advanced packings allows to the reduction increases to 24.4%.
3D Printing of Aqueous Two-Phase Systems with Linear and Bottlebrush Polyelectrolytes
In this study, we formed core–shell-like polyelectrolyte complexes (PECs) from an anionic bottlebrush polymer with poly (acrylic acid) side chains with a cationic linear poly (allylamine hydrochloride). By varying the pH, the number of side chains of the polyanionic BB polymers (Nbb), the charge density of the polyelectrolytes, and the salt concentration, the phase separation behavior and salt resistance of the complexes could be tuned by the conformation of the BBs. By combining the linear/bottlebrush polyelectrolyte complexation with all-liquid 3D printing, flow-through tubular constructs were produced that showed selective transport across the PEC membrane comprising the walls of the tubules. These tubular constructs afford a new platform for flow-through delivery systems.
Separating a multicomponent and multiphase liquid mixture with a 3D-printed membrane device
3D printed membrane device, supported ionic liquid membrane, hydrogel-coated hydrophilic/oleophobic membrane, multi-component multi-phase separation.
Controlled thermal expansion printed wiring boards based on liquid crystal polymer dielectrics
Dielectric materials based on innovative Liquid Crystal Polymers (LCP's) have been used to fabricate surface mount printed wiring boards (PWB's) with a coefficient of thermal expansion matched to leadless ceramic chip carriers. Proprietary and patented polymer processing technology has resulted in self reinforcing material with balanced in-plane mechanical properties. In addition, LCP's possess excellent electrical properties, including a low dielectric constant (less than 2.9) and very low moisture absorption (less than 0.02%). LCP-based multilayer boards processed with conventional drilling and plating processes show improved performance over other materials because they eliminate the surface flatness problems of glass or aramid reinforcements. Laser drilling of blind vias in the LCP dielectric provides a very high density for use in direct chip attach and area array packages. The material is ideally suited for MCM-L and PCMCIA applications fabricated with very thin dielectric layers of the liquid crystal polymer.
A Versatile Approach to Stabilize Liquid–Liquid Interfaces using Surfactant Self-Assembly
Stabilizing liquid–liquid interfaces, whether between miscible or immiscible liquids, is crucial for a wide range of applications, including energy storage, microreactors, and biomimetic structures. Here, in this study, a versatile approach for stabilizing the water-oil interface is presented using the morphological transitions that occur during the self-assembly of anionic, cationic, and nonionic surfactants mixed with fatty acid oils. The morphological transitions underlying this approach are characterized and extensively studied through small-angle X-ray scattering (SAXS), rheometry, and microscopy techniques. Dissipative particle dynamics (DPD) as a simulation tool is adopted to investigate these morphological transitions both in the equilibrium ternary system as well as in the dynamic condition of the water-oil interface. Such a versatile strategy holds promise for enhancing applications such as liquid-in-liquid 3D printing. Moreover, it has the potential to revolutionize a wide range of fields where stabilizing liquid–liquid interfaces not only offers unprecedented opportunities for fine-tuning nanostructural morphologies but also imparts interesting practical features to the resulting liquid shapes. These features include perfusion capabilities, self-healing, and porosity, which could have significant implications for various industries.
A versatile approach to stabilize liquid-liquid interfaces using surfactant self-assembly
Stabilizing liquid–liquid interfaces, whether between miscible or immiscible liquids, is crucial for a wide range of applications, including energy storage, microreactors, and biomimetic structures. In this study, a versatile approach for stabilizing the water-oil interface is presented using the morphological transitions that occur during the self-assembly of anionic, cationic, and nonionic surfactants mixed with fatty acid oils. The morphological transitions underlying this approach are characterized and extensively studied through small-angle X-ray scattering (SAXS), rheometry, and microscopy techniques. Dissipative particle dynamics (DPD) as a simulation tool is adopted to investigate these morphological transitions both in the equilibrium ternary system as well as in the dynamic condition of the water-oil interface. Such a versatile strategy holds promise for enhancing applications such as liquid-in-liquid 3D printing. Moreover, it has the potential to revolutionize a wide range of fields where stabilizing liquid–liquid interfaces not only offers unprecedented opportunities for fine-tuning nanostructural morphologies but also imparts interesting practical features to the resulting liquid shapes. These features include perfusion capabilities, self-healing, and porosity, which could have significant implications for various industries.
Rapid Quantification of 237 U Specific Activity for Nuclear Forensics
In the event of an unattributed nuclear explosion, rapid assessment of the short-lived uranium isotope activity and mass can provide valuable information for subsequent forensic analysis. Rapid analysis in the field is enabled by using microfluidic chemistry and deployable instrumentation. Here, this work presents a flow chemistry system, controlled in LabVIEW, that integrates three functionalities: (1) selective extraction of uranium from the sample matrix via a 3D-printed supported liquid membrane module; (2) UV–visible absorbance spectrophotometry to measure the total uranium concentration in the strip flow; and (3) a portable CdTe γ-ray spectrometer coupled to a 3D-printed flow cell to measure 237 U activity concentration in the strip solution. The system was calibrated using standard solutions, and its functionality was demonstrated using a solution of depleted uranium spiked with 237 U. Uranium concentrations of 40–5000 μg/mL were directly quantified online using a 100 mm optical flow cell, while concentrations of 0.5–10 μg/mL were quantified online using a colorimetric reagent. The mass concentration measurement takes approximately 60 min while the activity concentration via γ-ray spectrometry varies depending on the activity of 237 U, with 1 kBq/mL requiring about 30 min of acquisition time to obtain <10% uncertainty at 1σ. This platform provides a fieldable approach for quantifying uranium mass and radioactivity relevant to postdetonation nuclear debris.
Repairable and Reconfigurable Structured Liquid Circuits
The advance of printed electronics is significantly bolstered by the development of liquid-state electronics that overcome the inherent limitations in flexibility and reconfigurability of solid-state electronics. By integrating the biocompatibility and conductivity of sulfonated polyaniline (S-PANI) and phytic acid (PA) with the reconfigurability of structured liquids, highly conductive all-liquid threads are developed. The dense packing and overlap of PA/S-PANI complexes at an oil/water interface promotes in-plane electron transport, and standard four-point probe measurements of PA/S-PANI interfacial assemblies demonstrate enhanced electrical properties. Notably, the rapid jetting of the ink phase into the matrix phase allows for liquid threads to be printed, enabling the fabrication of large-scale, conductive pathways between two electrodes and liquid circuits. Upon mechanical cleavage of the liquid wires, circuits can be broken, but will easily self-repair using an electric field, making this motif useful in the design of switches as well as restoring conductive pathways in series or in parallel. In conclusion, the demonstrated flexibility and reconfigurability these PA/S-PANI wires possess hold significant promise for their practical use in the design of flexible and adaptive bioelectronics that can be repaired on demand, signifying a transformative step in the evolution of liquid electronic materials.
Millimeter-wave electromagnetic monitoring for liquid metal droplet-on-demand printing
As new printing approaches emerge, in situ diagnostics to monitor the print quality in real-time become essential for long-term monitoring and feedback control. In this article, we present a millimeter-wave electromagnetic monitoring approach for liquid metal droplet-on-demand printing to support the high-speed and real-time evaluation of droplet ejection. An open-ended rectangular waveguide is placed perpendicular to a jetted droplet stream and operated at a continuous-wave frequency of 40 GHz. Liquid metal droplets with diameters as low as 1.2 mm are characterized, and droplet jetting events on the order of 500 μm are detected at ejection rates up to 80 Hz. The measured results demonstrate that trends at the macro-level (large-scale print variation and anomalies at the nozzle tip) as well as micro-level (droplet size, position, and dynamics) can be detected using this technique.
Heterojunction Transistors Printed via Instantaneous Oxidation of Liquid Metals
Not provided.
Initial Assessment of 3D-Printed Molybdenum Lattices as a Substrate for Liquid Metal Plasma-Facing Components
Many liquid metal plasma-facing component concepts for fusion reactors require a capillary porous material to wick the liquid metal to the surface of the component. In this work, samples of 3D-printed molybdenum lattices designed to have pore sizes ranging from 100 to 1000 µm were fabricated by two different suppliers. The dimensions of the lattice structures were characterized using an optical microscope, revealing that the lattice walls were almost systematically thicker than they were designed to be and in turn the pores are all smaller than they were designed to be. In many cases the pores were completely clogged. Several spectroscopic techniques were used to characterize the chemical composition of the materials, collectively indicating the presence of a thick layer of oxygen-rich material extending more than 1 µm below the surface. Compression testing revealed significant asymmetry in the mechanical behavior depending on which direction the force was applied relative to the print direction. Lastly, lithium wetting tests of several lattice samples were performed, and a sample with ~250-µm pores was found to soak up lithium quickly after initial wetting of the surface occurred. The implications of these results for future liquid metal plasma-facing component design are discussed.