Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mars aerobots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

34 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Advanced Communication and Networking Technologies for Mars Exploration

Next-generation Mars communications networks will provide communications and navigation services to a wide variety of Mars science vehicles including: spacecraft that are arriving at Mars, spacecraft that are entering and descending in the Mars atmosphere, scientific orbiter spacecraft, spacecraft that return Mars samples to Earth, landers, rovers, aerobots, airplanes, and sensing pods. In the current architecture plans, the communication services will be provided using capabilities deployed on the science vehicles as well as dedicated communication satellites that will together make up the Mars network. This network will evolve as additional vehicles arrive, depart or end their useful missions. Cost savings and increased reliability will result from the ability to share communication services between missions. This paper discusses the basic architecture that is needed to support the Mars Communications Network part of NASA's Space Science Enterprise (SSE) communications architecture. The network may use various networking technologies such as those employed in the terrestrial Internet, as well as special purpose deep-space protocols to move data and commands autonomously between vehicles, at disparate Mars vicinity sites (on the surface or in near-Mars space) and between Mars vehicles and earthbound users. The architecture of the spacecraft on-board local communications is being reconsidered in light of these new networking requirements. The trend towards increasingly autonomous operation of the spacecraft is aimed at reducing the dependence on resource scheduling provided by Earth-based operators and increasing system fault tolerance. However, these benefits will result in increased communication and software development requirements. As a result, the envisioned Mars communications infrastructure requires both hardware and protocol technology advancements. This paper will describe a number of the critical technology needs and some of the ongoing research activities.

Bhasin, Kul↗
NASA NTRS1997

On-board State Estimation for Planetary Aerobots

Oscillatory balloon systems with telerobotic capabilities are being studied to support future space exploration by probes which will move up and down in a planetary atmosphere, land and explore numerous surface sites.

Planetary↗
NASA NTRS2003

Detecting Near-Surface Water and Hydrate Minerals on Mars from a Rover, Penetrator, or Borehole: The HYDRA Instrument

One of the major goals of near term NASA Mars exploration is to identify exact locations of near-surface water or hydrated minerals on Mars. Evidence for the existence of recent nearsurface water on Mars underscores the need for developing instrumentation that can identify water or hydrated minerals very near the surface. Further encouraging evidence of surface and near-surface water and hydrate minerals on Mars comes from neutron spectrometer measurements aboard Mars Odyssey. Preliminary results show very large regions of high hydrogen content poleward of 60 deg. latitude, as well as interesting features closer to the equator. However, spatial resolution from orbit is very poor, approx. 400 km. The next logical step is to use in-situ or near-surface investigations to map in detail some of the most interesting features. Relatively simple instrumentation based on He-3 gas proportional counters were shown to be highly successful on the Lunar Prospector mission in identifying even low levels of enhanced hydrogen abundances. Here we discuss HYDRA, a water- and hydrate-sensing instrument currently being developed under the NASA Mars Instrument Development Program (MIDP). HYDRA is based on Lunar Prospector technology, and is intended as a rover body-mounted instrument, or an instrument on an aerobot, penetrator, hard lander on the surface of Mars, or for borehole stratigraphy applications. Our proposed instrument would be ideal for such platforms as it would be small (less than 7 cm diameter by 10 cm long), low mass (less than 500 g), low power (less than 1W), and have a low data volume per measurement. We use neutron spectrometry (a) because of its proven ability to uniquely detect and quantify hydrogen abundance, and (b) because the resources required by this approach (weight, power, size, telemetry bandwidth, and measurement time) are extremely low. This compact neutron spectrometer package, comprised of two small He-3 gas proportional counters, offers superior sensitivity, extensive flight heritage, and inherent ruggedness. These tubes have survived approx. 1500 g's of acceleration in penetrator tests. In a landed application, HYDRA would help address many topics of interest to the Mars Exploration and Astrobiology communities: (a) nature and origin of stratified deposits; (b) water cycle(s) and temporal changes; (c) early water oceans, aquifers, precipitation; (d) current extent/location/state of water; (e) polar cap processes and temporal changes; (f) where extremeophiles could survive on Mars; (g) paleoclimate surface signatures and modeling; (h) strategies for future Mars exploration.

R C Elphic↗
NASA NTRS2022

Exploring the Clouds of Venus: Science Driven Aerobot Missions to Our Sister Planet

Venus is essential to our understanding of the evolution and habitability of Earth-size planets throughout the galaxy. The selection of the VERITAS, EnVision, and DAVINCI missions by NASA and ESA in June 2021 is an important step in advancing the science. However, addressing many of the most challenging questions will require in situ platforms that can operate in the Venus environment for extended periods in order to capture the full complexity of our sister planet. Aerobots are aerial vehicles that exploit buoyancy to achieve long-duration operation in the Venus cloud layer where environmental conditions are comparatively benign. Buoyancy control, explained in more detail in a companion paper at this conference, allows aerobots to change altitude with little energy expenditure enabling new scientific measurement opportunities. These include atmospheric chemistry, dynamics, geophysical measurements of the crust and interior and geological investigations enabled by high resolution surface imaging. One aspect to our approach to defining missions that fit within the resource constraints of competitive missions is keeping the scale small. Today’s science-driven appetite for sophisticated measurements and large volumes of data is driving size upwards but advances in technology can enable aerobots that can be delivered to Venus at manageable costs. The other aspect is supporting the aerobot at Venus with orbiters providing data relay, localization and synergistic science. The recently selected orbiters, equipped with low-cost proximity relay systems routinely used at Mars may obviate the need for dedicated orbiters thereby enabling Discovery mission candidates. Four aerobot mission concepts have been defined which fit comfortably within the current New Frontiers (NF) cost cap ($900M in $FY22). One of these concepts would also be a candidate for a Discovery mission if that cost cap ($500M in $FY19) were raised. Raising the NF cost cap would enable more capable aerobot missions combining both altitude control with synergistic orbital observations. Investigations of surface geology at high resolution with subcloud NIR nightside imaging and dropsondes on the dayside of Venus could also benefit from collaborations with foreign contributions.

"O'Rourke, Joseph"↗
NASA NTRS1997

Mars 2001 Aerobot/Balloon System Overview

The purpose of the study was to determine technical feasibiltiy of a long duration 2001 aerobot mission in the Martian atmosphere, to formulate a baseline concept, to identify pre-project technology requirements and to develop a preliminary cost, schedule and plan.

Mars↗
NASA NTRS2005

Autonomous flight control for a Titan exploration aerobot

Robotic lighter-than-air vehicles, or aerobots, provide strategic platform for the exploration of planets and moons with an atmosphere, such as Venus, Mars, Titan and the gas giants. In this paper, we discuss steps towards the development of an autonomy architecture, and concentrate on the autonomous fight control subsystem.

robotic airship↗
NASA NTRS2000

AI in Space: The Era of Autonomous Space Systems

The development of autonomy capabilities is the key to three vastly important strategic technical challenges facing NASA: the reduction of mission costs, the continuing return of quality science products through limited communications bandwidth, and the launching of a new era of solar system exploration characterized by sustained presence and in-depth scientific studies, including the search for life. Autonomy will benefit future NASA missions by migrating routine, traditionally ground-based functions to the spacecraft, by directly supporting the decoupling of spacecraft from the ground through new operations concepts, by enabling direct links between scientists and the space platforms carrying their instruments of investigation, and by the closing, of planning and control loops onboard, enabling space platforms to directly address uncertainty in the real-time mission context. The talk will survey ongoing, autonomy technology development projects at NASA, many of which have been or will soon be the subject of flight technology experiments, or are already targeted for mission use. The talk will also survey the exciting suite of future NASA space exploration missions, and make the case for the central role of autonomy in achieving the goals of these bold, unprecedented missions: cooperating rovers on the surface of Mars, the search for Earth-like planets around nearby stars, asteroid and comet landers, aerobots in planetary atmospheres, and a series of missions to intriguing Europa, perhaps culminating in a submersible to investigate its putative ocean. Finally, the talk will conclude with some farther-reaching speculations on how to create properties such as long-term survivability and evolvability in future space systems, such that they will be well equipped to extend humanity exploratory presence into the interstellar realm.

Doyle, Richard J.↗
NASA NTRS2000

A Light-Weight Inflatable Hypersonic Drag Device for Planetary Entry

The author has analyzed the use of a light-weight inflatable hypersonic drag device, called a ballute, for flight in planetary atmospheres, for entry, aerocapture, and aerobraking. Studies to date include Mars, Venus, Earth, Saturn, Titan, Neptune and Pluto, and data on a Pluto lander and a Mars orbiter will be presented to illustrate the concept. The main advantage of using a ballute is that aero, deceleration and heating in atmospheric entry occurs at much smaller atmospheric density with a ballute than without it. For example, if a ballute has a diameter 10 times as large as the spacecraft, for unchanged total mass, entry speed and entry angle,the atmospheric density at peak convective heating is reduced by a factor of 100, reducing the heating by a factor of 10 for the spacecraft and a factor of 30 for the ballute. Consequently the entry payload (lander, orbiter, etc) is subject to much less heating, requires a much reduced thermal. protection system (possibly only an MLI blanket), and the spacecraft design is therefore relatively unchanged from its vacuum counterpart. The heat flux on the ballute is small enough to be radiated at temperatures below 800 K or so. Also, the heating may be reduced further because the ballute enters at a more shallow angle, even allowing for the increased delivery angle error. Added advantages are less mass ratio of entry system to total entry mass, and freedom from the low-density and transonic instability problems that conventional rigid entry bodies suffer, since the vehicle attitude is determined by the ballute, usually released at continuum conditions (hypersonic for an orbiter, and subsonic for a lander). Also, for a lander the range from entry to touchdown is less, offering a smaller footprint. The ballute derives an entry corridor for aerocapture by entering on a path that would lead to landing, and releasing the ballute adaptively, responding to measured deceleration, at a speed computed to achieve the desired orbiter exit conditions. For a lander an accurate landing point could be achieved by providing the lander with a small gliding capacity, using the large potential energy available from being subsonic at high altitude. Alternatively the ballute can be retained to act as a parachute or soft-landing device, or to float the payload as a buoyant aerobot. As expected, the ballute has smaller size for relatively small entry speeds, such as for Mars and Titan, or for the extensive atmosphere of a low-gravity planet such as Pluto. Details of a ballute to place a small Mars orbiter and a small Pluto lander will be given to illustrate the concept. The author will discuss presently available ballute materials and a development program of aerodynamic tests and materials that would be required for ballutes to achieve their full potential.

McRonald, Angus D.↗
NASA NTRS1995

A Light-Weight Inflatable Hypersonic Drag Device for Planetary Entry

The author has analyzed the use of a light-weight inflatable hypersonic drag device, called a ballute, (balloon + parachute) for flight in planetary atmospheres, for entry, aerocapture, and aerobraking. Studies to date include missions to Mars, Venus, Earth, Saturn, Titan, Neptune and Pluto. Data on a Pluto lander and a Mars orbiter will be presented to illustrate the concept. The main advantage of using a ballute is that aero deceleration and heating in atmospheric entry occurs at much smaller atmospheric density with a ballute than without it. For example, if a ballute has a diameter 10 times as large as the spacecraft, for unchanged total mass, entry speed and entry angle,the atmospheric density at peak convective heating is reduced by a factor of 100, reducing the peak heating by a factor of 10 for the spacecraft, and a factor of about 30 for the ballute. Consequently the entry payload (lander, orbiter, etc) is subject to much less heating, requires a much reduced thermal protection system (possibly only an MLI blanket), and the spacecraft design is therefore relatively unchanged from its vacuum counterpart. The heat flux on the ballute is small enough to be radiated at temperatures below 800 K or so. Also, the heating may be reduced further because the ballute enters at a more shallow angle, even allowing for the increased delivery angle error. Added advantages are a smaller mass ratio of entry system to total entry mass, and freedom from the low-density and transonic instability problems that conventional rigid entry bodies suffer, since the vehicle attitude is determined by the ballute, usually released at continuum conditions (hypersonic for an orbiter, and subsonic for a lander). Also, for a lander the range from entry to touchdown is less, offering a smaller footprint. The ballute derives an entry corridor for aerocapture by entering on a path that would lead to landing, and releasing the ballute adaptively, responding to measured deceleration, at a speed computed to achieve the desired orbiter exit conditions. For a lander an accurate landing point could be achieved by providing the lander with a small gliding capacity, using the large potential energy available from being subsonic at high altitude. Alternatively the ballute can be retained to act as a parachute or soft-landing device, or to float the payload as a buoyant aerobot. As expected, the ballute has smaller size for relatively small entry speeds, such as for Mars, or for the extensive atmosphere of a low-gravity planet such as Pluto. The author will discuss presently available ballute materials and a development program of aerodynamic tests and materials that would be required for ballutes to achieve their full potential.

McRonald, Angus D.↗
NASA NTRS1996

Planetary Aerobots: A Program for Robotic Balloon Exploration

The exploration of the solar system has proceeded in several phases beginning with flyby missions, proceeding to orbiters, then to probes and landers and finally mobile vehicles that operate on the surface and in its atmosphere. For the most accessible planetary bodies, Venus and Mars, we are now entering the phase of mobile exploration of the surface and atmosphere.

robotically-controlled↗
NASA NTRS2001

Recent progress in planetary balloons

In the last 15 years several balloon mission concepts have been proposed for Mars and Venus, one of them - Russian-French Mars Aerostat - was extensively developed in 1988-1995 but was terminated before completion.

planets balloons aerobots↗
NASA NTRS1995

Aerovehicles for Planetary Exploration

Planetary aerobots are described. They are a new type of lightweight and low-cost telerobot that use phase change fluids to ascend and descend, thus allowing data acquisition from multiple sites. Potential near-term missions discussed include those to Venus, Mars, and Titan. Similarities are discussed for missions in the Earth atmosphere and deep sea.

telerobotics aerovehicles autonomous vehicles↗
NASA NTRS2022

Benchmarking and Testing of Qualcomm Snapdragon System-on-Chip for JPL Space Applications and Missions

As some space missions become more challenging due to new environments, greater distances, or more limited size, weight, and power (SWaP) constraints, spacecraft avionics must adapt to allow the spacecraft to be more autonomous and agile---eliminating the Spacecraft-Earth-Spacecraft feedback loop whenever possible. Prime examples of such missions include Aerobots (such as Ingenuity with extremely low SWaP constraints and demanding signal/image processing during flight) and landers in possibly hostile environments (such as a Europa lander mission, with limited communication capacity, high latency, and constrained power budget). To address these challenges, JPL worked with Qualcomm to demonstrate the use of their Snapdragon 801 system-on-chip (SoC) onboard the Ingenuity Helicopter on Mars. The Qualcomm Snapdragon SoC contains various subsystems, including an ARM cluster, a Graphics processing unit, a Digital Signal Processing subsystem, a Neural Processing Engine, Image Signal Processing subsystem, among others. Since the success of Ingenuity, JPL is continuing to work with Qualcomm to address other applications of the Snapdragon SoC technology. This includes the deployment of two 855 Snapdragon development boards onboard the International Space Station (ISS) for successful in-situ benchmarking of applications in space (beyond those tested on Ingenuity). In this paper, we will examine the performance of various applications that have been identified to benefit from greater onboard computational capability. These applications include (among others): machine vision algorithms that are expected to be critical in autonomous entry-descent-and-landing scenarios and real-time Aerobot flight navigation; Hyperspectral compression algorithms; Synthetic Aperture Radar Processing along with various instrument processing algorithms. We discuss how the infusion of Qualcomm's Snapdragon SoC is capable of enabling missions that may not have been able to achieve their goals with traditional flight computing. In addition, we also show that for some algorithms, the software implementation on the Snapdragon SoC outperforms traditional FPGA implementations.

Cretu, Vlad↗
NASA NTRS2010

Coordinating Multiple Spacecraft Assets for Joint Science Campaigns

This paper describes technology to support a new paradigm of space science campaigns. These campaigns enable opportunistic science observations to be autonomously coordinated between multiple spacecraft. Coordinated spacecraft can consist of multiple orbiters, landers, rovers, or other in-situ vehicles (such as an aerobot). In this paradigm, opportunistic science detections can be cued by any of these assets where additional spacecraft are requested to take further observations characterizing the identified event or surface feature. Such coordination will enable a number of science campaigns not possible with present spacecraft technology. Examples from Mars include enabling rapid data collection from multiple craft on dynamic events such as new Mars dark slope streaks, dust-devils or trace gases. Technology to support the identification of opportunistic science events and/or the re-tasking of a spacecraft to take new measurements of the event is already in place on several individual missions such as the Mars Exploration Rover (MER) Mission and the Earth Observing One (EO1) Mission. This technology includes onboard data analysis techniques as well as capabilities for planning and scheduling. This paper describes how these techniques can be cue and coordinate multiple spacecraft in observing the same science event from their different vantage points.

automated commanding↗
NASA NTRS2009

Mars Balloon Flight Test Results

This paper describes a set of four Earth atmosphere flight test experiments on prototype helium superpressure balloons designed for Mars. Three of the experiments explored the problem of aerial deployment and inflation, using the cold, low density environment of the Earth's stratosphere at an altitude of 30-32 km as a proxy for the Martian atmosphere. Auxiliary carrier balloons were used in three of these test flights to lift the Mars balloon prototype and its supporting system from the ground to the stratosphere where the experiment was conducted. In each case, deployment and helium inflation was initiated after starting a parachute descent of the payload at 5 Pa dynamic pressure, thereby mimicking the conditions expected at Mars after atmospheric entry and high speed parachute deceleration. Upward and downward looking video cameras provided real time images from the flights, with additional data provided by onboard temperature, pressure and GPS sensors. One test of a 660 cc pumpkin balloon was highly successful, achieving deployment, inflation and separation of the balloon from the flight train at the end of inflation; however, some damage was incurred on the balloon during this process. Two flight tests of 12 m diameter spherical Mylar balloons were not successful, although some lessons were learned based on the failure analyses. The final flight experiment consisted of a ground-launched 12 m diameter spherical Mylar balloon that ascended to the designed 30.3 km altitude and successfully floated for 9.5 hours through full noontime daylight and into darkness, after which the telemetry system ran out of electrical power and tracking was lost. The altitude excursions for this last flight were +/-75 m peak to peak, indicating that the balloon was essentially leak free and functioning correctly. This provides substantial confidence that this balloon design will fly for days or weeks at Mars if it can be deployed and inflated without damage.

deployment↗