Search NASA⌕ Search

SEARCH · Search NASA

Results for “RECTANGULAR PANEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Noise transmission through flat rectangular panels into a closed cavity

Five panels backed by a closed cavity were studied experimentally and analytically to determine the noise transmission characteristics of the coupled panel-cavity system. The closed cavity was studied both with and without fiber-glass lining to provide either an absorbent or a reverberant acoustic space. The effects on noise reduction of cavity absorption, measurement location within the cavity, panel mass, and panel stiffness were examined. Results indicated that both measurement location and absorption in the cavity have significant effects on the noise reduction. Increasing panel mass improves the noise reduction at almost all frequencies, and increasing panel stiffness improves nose reduction below the fundamental resonance frequency. A simple, one dimensional analytical model was developed which provided good agreement with the experimental results.

Barton, C. K.↗
NASA NTRS1987

Effect of boundary conditions on dynamic strain response of rectangular panels

An analytical and experimental research program has been initiated at NASA Langley to investigate the strain response of panels under severe thermal and/or acoustic loads. The overall purpose of this program is to develop an analytical model that predicts the stresses and strains leading to sonic fatigue failure in advanced aircraft and aerospace structures. Previous experiments, analyses, and results of this program are reviewed. The analytical modeling refinements and their effects on the calculation of strain are discussed, considering the inclusion of in-plane motion at the panel boundary; the use of the multiterm, multimode Ritz method; and the introduction of transverse stiffness at the boundary. Finally, the findings of the analytical modeling investigation are summarized.

Roussos, Louis A.↗
NASA NTRS2005

Enhancements of Tow-Steering Design Techniques: Design of Rectangular Panel Under Combined Loads

An extension to existing design tools that utilize tow-steering is presented which is used to investigate the use of elastic tailoring for a flat panel with a central hole under combined loads of compression and shear. The elastic tailoring is characterized by tow-steering within individual lamina as well as a novel approach based on selective reinforcement, which attempts to minimize compliance through the use of Cellular Automata design concepts. The selective reinforcement designs lack any consideration of manufacturing constraints, so a new tow-steered path definition was developed to translate the prototype selective reinforcement designs into manufacturable plies. The minimum weight design of a flat panel under combined loading was based on a model provided by NASA-Langley personnel and analyzed by STAGS within the OLGA design environment. Baseline designs using traditional straight fiber plies were generated, as well as tow-steered designs which incorporated parallel, tow-drop, and overlap plies within the laminate. These results indicated that the overlap method provided the best improvement with regards to weight and performance as compared to traditional constant stiffness monocoque panels, though the laminates did not measure up to similar designs from the literature using sandwich and isogrid constructions. Further design studies were conducted using various numbers of the selective reinforcement plies at the core and outer surface of the laminate. None of these configurations exhibited notable advantages with regard to weight or buckling performance. This was due to the fact that the minimization of the compliance tended to direct the major stresses toward the center of the panel, which decreased the ability of the structure to withstand loads leading to instability.

Tatting, Brian F.↗
NASA NTRS2007

Mechanical Properties of 17-4PH Stainless Steel Foam Panels

Rectangular 17-4PH stainless steel sandwiched foam panels were fabricated using a commercial manufacturing technique by brazing two sheets to a foam core. Microstructural observations and ultrasonic nondestructive evaluation of the panels revealed large variations in the quality of the brazed areas from one panel to the next as well as within the same panel. Shear tests conducted on specimens machined from the panels exhibited failures either in the brazed region or in the foam core for the poorly brazed and well-brazed samples, respectively. Compression tests were conducted on the foam cores to evaluate their elastic and plastic deformation behavior. These data were compared with published data on polymeric and metallic foams, and with theoretical deformation models proposed for open cell foams.

Raj, S. V.↗
NASA NTRS1960

Flutter Research on Skin Panels

Representative experimental results are presented to show the current status of the panel flutter problem. Results are presented for unstiffened rectangular panels and for rectangular panels stiffened by corrugated backing. Flutter boundaries are established for all types of panels when considered on the basis of equivalent isotropic plates. The effects of Mach number, differential pressure, and aerodynamic heating on panel flutter are discussed. A flutter analysis of orthotropic panels is presented in the appendix.

Kordes, Eldon E.↗
NASA NTRS1994

Mechanical and thermal buckling analysis of rectangular sandwich panels under different edge conditions

The combined load (mechanical or thermal load) buckling equations were established for orthotropic rectangular sandwich panels under four different edge conditions by using the Rayleigh-Ritz method of minimizing the total potential energy of a structural system. Two-dimensional buckling interaction curves and three-dimensional buckling interaction surfaces were constructed for high-temperature honeycomb-core sandwich panels supported under four different edge conditions. The interaction surfaces provide overall comparison of the panel buckling strengths and the domains of symmetrical and antisymmetrical buckling associated with the different edge conditions. In addition, thermal buckling curves of these sandwich panels are presented. The thermal buckling conditions for the cases with and without thermal moments were found to be identical for the small deformation theory.

Ko, William L.↗