SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Transonic wind tunnel tests of vertical fin loads and rudder hinge moments on M2-F3 lifting body scale model at Mach 0.50 to 1.30
Wind tunnel tests were performed to examine the concept of aircraft controls without moving parts, and aircraft stabilization by means of scoop-fed slots. Results of wind tunnel tests, in the framework of a NASA program, to determine the force-control characteristics of a symmetrical airfoil with scoop-fed slots are discussed. Further tests showed that a fluidic amplifier could be built into the airfoil and operate with ram air. A fluidic rudder was then developed, consisting of cascaded fluidic amplifiers necessary to couple low-level fluidic sensors with slot flow control of the aerodynamic force on the vertical tail.
A hydrogen peroxide fueled rocket system, which is to be used as a research tool in flight studies of stall and spin maneuvers, was installed on a light, four place general aviation airplane. The pilot controlled rocket system produces moments about either the roll or the yaw body axis to augment or oppose the aerodynamic forces and inertial moments acting on the airplane during various flight maneuvers, including the spin. These controlled moments of a known magnitude can be used in various ways to help analyze and interpret the importance of the various factors which influence airplane maneuvers. The rocket system and its installation in the airplane are described, and the results of flight rests used to measure rudder and aileron effectiveness at airspeeds above the stall are presented. These tests also serve to demonstrate the operational readiness of the rocket system for future research operations.
A piloted simulator study was conducted to evaluate an aileron rudder interconnect (ARI) control system for the F-14A airplane in the landing configuration. Effects on pilot performance and handling characteristics were investigated. Two ARI configurations were tested and compared to the standard F-14 fleet control system. A nonlinear aerodynamic model of the F-14 was used in conjunction with a six degree of freedom motion base simulator. The evaluation task, which utilized three subject pilots, consistent of a night carrier approach and landing. Both ARI configurations produced improved pilot performance and pilot ratings when compared to the standard control system. Sideslip due to adverse yaw as considerably reduced by the ARI systems and heading control was more stable and precise. Lateral deviation from centerline was reduced during the approach and lateral touchdown dispersion on the carrier deck was reduced with the ARI control systems.
A flight test was conducted for preliminary evaluation of an aileron-rudder interconnect (ARI) control system for the F-14A airplane in the landing configuration. Two ARI configurations were tested in addition to the standard F-14 flight control system. Results of the flight test showed marked improvement in handling qualities when the ARI systems were used. Sideslip due to adverse yaw was considerably reduced, and airplane turn rate was more responsive to pilot lateral control inputs. Pilot comments substantiated the flight data and indicated that the ARI systems were superior to the standard control system in terms of pilot capability to make lateral offset corrections and heading changes on final approach.
Autonomous modal identification automates the calculation of natural vibration frequencies, damping, and mode shapes of a structure from experimental data. This technology complements damage detection techniques that use continuous or periodic monitoring of vibration characteristics. The approach shown in the paper incorporates the Eigensystem Realization Algorithm (ERA) as a data analysis engine and an autonomous supervisor to condense multiple estimates of modal parameters using ERA's Consistent-Mode Indicator and correlation of mode shapes. The procedure was applied to free-decay responses of a Space Shuttle tail rudder and successfully identified the seven modes of the structure below 250 Hz. The final modal parameters are a condensed set of results for 87 individual ERA cases requiring approximately five minutes of CPU time on a DEC Alpha computer.
Fatigue life analyses were performed using a standard strain-life approach and a linear cumulative damage parameter to assess the effect of a single accidental overload on the fatigue life of the Haynes 230 nickel-base superalloy X-43A rudder spindle. Because of a limited amount of information available about the Haynes 230 material, a series of tests were conducted to replicate the overload and in-service conditions for the spindle and corroborate the analysis. Both the analytical and experimental results suggest that the spindle will survive the anticipated flight loads.
The first major structural component failure of a composite part on a commercial airplane occurred during the crash of American Airlines Flight 587. The fractured composite lugs that attached the vertical stabilizer to the aircraft tail and the fractured composite honeycomb rudder were examined as part of the National Transportation Safety Board investigation of the accident. In this paper the composite fractures are described and the resulting clues to the failure events are discussed.
High performance aircraft, especially those with twin vertical tails, encounter unsteady buffet loads when flying at high angles of attack. These stochastic loads result in significant stresses, which may cause fatigue damage leading to restricted capabilities and availability of the aircraft. An international collaborative research activity among Australia, Canada and the United States, conducted under the auspices of The Technical Cooperation Program (TTCP) contributed resources toward a program that coalesced a broad range of technical knowledge and expertise into a single investigation to demonstrate the enhanced performance and capability of the advanced active Buffet Load Alleviation ( ) control system in preparation for a flight test demonstration. The research team investigated the use of active structural control to alleviate the damaging structural response to these loads by applying advanced directional piezoelectric actuators, the aircraft rudder, switch mode amplifiers, and advanced control strategies on an F/A-18 aircraft empennage. Some results of the full-scale investigation are presented herein.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.