Search NASA⌕ Search

SEARCH · Search NASA

Results for “SCREEN PRINTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Detailed investigation of electrical and optical properties of textured n-type and roughened p-type tunnel oxide passivated contacts for screen-printed double-side passivated contact silicon solar cell application

Here, this paper presents detailed characterization and analyses of the optical, electrical, and contact properties of a 35 nm phosphorus-doped (n-type) polysilicon (poly-Si) and a 250 nm boron-doped (p-type) poly-Si deposited respectively on textured and roughed surface. These layers could be applied respectively to the front and rear sides of an n-type Si to produce back junction bifacial screen-printed double-side tunnel oxide passivated contacts (DS-TOPCon) solar cells. Optical and device modeling revealed a short circuit current density loss of 1.5 mA/cm 2 and 0.5 mA/cm 2 due to absorption in the front n-TOPCon and rear side p-TOPCon layers, respectively. The passivation and contact properties including metalized and unmetallized recombination current density (J 0 ), as well as contact resistivity, were determined as a function of contact firing temperature in the range of 700~800°C. The passivation quality of the front thin n-TOPCon was found to deteriorate with increased firing temperature while the rear thick p-TOPCon improved. The study showed that the simulated contact firing at 730°C resulted in the best unmetallized double-side TOPCon precursor, with an excellent implied open-circuit voltage of 730 mV and implied fill factor of ~86 %. However, the metalized J0 increased and contact resistivity decreased monotonically with the increase in the firing temperature. The 2D device simulations revealed that these layers can produce screen-printed DS-TOPCon cells with an efficiency of ~22.5 %. Solar cell modeling also showed that the DS-TOPCon solar cell efficiency can reach 24.1 % by decreasing the n-TOPCon thickness to 20 nm and lowering the full area metalized J 0 to ~100 mA/cm 2 .

14 SOLAR ENERGY↗

>24% screen printed Cu contacted n-TOPCon solar cells with successful implementation of LECO process

In this paper, we report the successful fabrication of >24.0 % efficiency n-TOPCon Si solar cells with screen-printed, fire-through Cu contact to n-TOPCon on the rear side and Ag contacted boron emitter on the front side by implementing optimized firing and LECO conditions. The highest efficiency (24.3%) Cu contacted n-TOPCon cell in this study showed excellent cell performance parameters with V oc >730 mV, J sc of 41.1 mA/cm 2 and FF of 80.8%, resulting in an absolute efficiency gap of 0.2% between Cu-contacted and fully Ag contacted n-TOPCon cells (24.5%). The mini-module fabricated with the Cu contacted n-TOPCon cell showed excellent reliability and durability of open-circuit voltage (V oc ), pseudo fill factor (pFF) and efficiency after prolonged damp-heat tests. Such high efficiency screen printed Cu contacted n-TOPCon cells provide unique opportunity to replace very expensive Ag contact on n-TOPCon with cheaper screen printable Cu metal pastes.

14 SOLAR ENERGY↗

Design, Optimization, and In-Depth Understanding of Front and Rear Junction Screen-Printed Double-Side Passivated Contacts Solar Cells

Investigate the efficiency potential of n-type screen-printed poly-Si based double-side tunnel oxide passivated contacts (DS-TOPCon) silicon solar cells Establish key material/device parameters and technologies to attain practically achievable DS-TOPCon cell efficiency by Quokka 2D Develop fundamental understanding of underlying mechanisms governing cell operation in front junction (FJ) and rear junction (RJ) cell designs to explain why RJ is a better choice for DS-TOPCon structure

14 SOLAR ENERGY↗

Near-Busbar Degradation of Screen-Printed Metallization in Silicon Photovoltaic Modules

We study photovoltaic (PV) module degradation after extended accelerated stress testing including 2000 hours of damp heat followed by a current-injection procedure meant to stabilize defects linked to light-induced degradation. In addition to de-stabilization/recovery of light-induced defects, we observe severe series resistance due to loss of contact between the Si cell and near-busbar screen-printed metallization (i.e. grid finger delamination). Using scanning electron microscopy and energy dispersive x-ray spectroscopy on cell fragments cored from the module, we show poor contact is caused by a gap between the screen-printed Ag metallization and Si due to missing glass frit.

degradation↗

Direct laser immobilization of photosynthetic material on screen printed electrodes for amperometric biosensor

This letter demonstrates the direct laser printing of photosynthetic material onto low cost nonfunctionalized screen printed electrodes for the fabrication of photosynthesis-based amperometric biosensors. The high kinetic energy of the transferred material induces direct immobilization of the thylakoids onto the electrodes without the use of linkers. This type of immobilization is able to establish efficient electrochemical contact between proteins and electrode, stabilizing the photosynthetic biomolecule and transporting electrons to the solid state device with high efficiency. The functionality of the laser printed biosensors was evaluated by the detection of a common herbicide such as Linuron.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct Mercury Detection in Landfill Leachate Using a Novel AuNP-Biopolymer Carbon Screen-Printed Electrode Sensor

A novel Au nanoparticle (AuNP)-biopolymer coated carbon screen-printed electrode (SPE) sensor was developed through the co-electrodeposition of Au and chitosan for mercury (Hg) ion detection. This new sensor showed successful Hg2+ detection in landfill leachate using square wave anodic stripping voltammetry (SWASV) with an optimized condition: a deposition potential of −0.6 V, deposition time of 200 s, amplitude of 25 mV, frequency of 60 Hz, and square wave step voltage of 4 mV. A noticeable peak was observed at +0.58 V associated with the stripping current of the Hg ion. The sensor exhibited a good sensitivity of ~0.09 μA/μg (~0.02 μA/nM) and a linear response over the concentration range of 10 to 100 ppb (50–500 nM). The limit of detection (LOD) was 1.69 ppb, which is significantly lower than the safety limit defined by the United States Environmental Protection Agency (USEPA). The sensor had an excellent selective response to Hg2+ in landfill leachate against other interfering cations (e.g., Zn2+, Pb2+, Cd2+, and Cu2+). Fifteen successive measurements with a stable peak current and a lower relative standard deviation (RSD = 5.1%) were recorded continuously using the AuNP-biopolymer-coated carbon SPE sensor, which showed excellent stability, sensitivity and reproducibility and consistent performance in detecting the Hg2+ ion. It also exhibited a good reliability and performance in measuring heavy metals in landfill leachate.

Hwang, Jae-Hoon (ORCID:0000000220100864)↗

Evaluation of phenolic antioxidant capacity in beverages based on laccase immobilized on screen-printed carbon electrode modified with graphene nanoplatelets and gold nanoparticles

A simple and highly sensitive electrochemical biosensor based on laccase immobilized onto a gold nanoparticles/graphene nanoplatelets-modified screen-printed carbon electrode (LACC/AuNP/GNPl/SPCE) was developed for the determination of hydroquinone (HQ) and other phenolic compounds. The biosensor shows excellent electro-catalytic activity towards oxidation of hydroquinone at a potential of -0.05 V (vs Ag/AgCl, 3 M KCl) in phosphate buffer as supporting electrolyte (0.1 M, pH 7.0) using hydrodynamic amperometry. Analytical characteristics uncover that the LACC/AuNP/GNPl/SPCE comprises a wide linear range for the dependence of the signal on HQ concentrations from 4 to 130 µM with a detection limit (3σ) of 1.5 µM. The repeatability (5 measurements, 100 µM hydroquinone) is ±2% and the reproducibility (5 biosensors, 100 µM hydroquinone) is ±3%. Interference studies of most common compounds with the determination of hydroquinone demonstrated negligible effects. Finally, the biosensor and the analytical method were applied to the determination of phenolic antioxidant capacity (AOC) in wine and blueberry syrup based on Trolox (6‑hydroxy‑2,5,7,8-tetramethylchromane-2-carboxylic acid) and hydroquinone equivalents. The results were evaluated by using their calibration curves which were satisfactory and agreed well with the results obtained by the reference method Trolox Equivalent Antioxidant Capacity assay (TEAC-Assay).

60 APPLIED LIFE SCIENCES↗

Study on mechanically alloyed tin telluride screen-printed films for optoelectronic device applications

Narrow band gap semiconductor tin telluride (SnTe) was synthesized by mechanical alloying and its film was deposited on glass substrates by the economically and commercially feasible screen-printing technique. Deposition of the film was followed by sintering. Different analytical techniques were utilized to study the structure, surface morphology, elemental, optical and electrical characteristics of the film. X-ray diffraction analysis confirms that the film is polycrystalline in nature and exhibits rock salt type structure with preferred orientation of grains along (200) direction. EDAX spectrum confirms the presence of Sn and Te elements in the film. SEM image shows that the film exhibits uniform surface. The energy band gap of the film was determined by reflection spectra. The film is found to have a direct band gap of 0.37 eV. The dark electrical conductivity and activation energy of the film were measured in temperature range 300–380 K. Hall Effect measurement indicates that the film has p-type electrical conductivity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Screen-Printed SHJ Solar Cells with Complex Silver Inks

Metallization using complex metal inks has gained significant research interest due to its cost-effectiveness and ability to achieve performance comparable to traditional nanoparticle pastes. This study introduces the use of complex silver (Ag) inks applied via industrial screen-printing for silicon heterojunction (SHJ) solar cell metallization. The printed Ag lines exhibit a contact resistivity on SHJ tin-doped indium oxide (ITO) surfaces as low as approximately 0.2-12 mO cm2. Photoluminescence imaging reveals minimal surface passivation degradation (iVoc < 3.5 mV), while scanning electron microscopy (SEM) shows a denser structure compared to Ag layer from nanoparticle pastes. The printed Ag grid features thin (approximately 1 micrometer), continuous fingers approximately 100-120 micrometer wide, significantly thinner than conventional approximately 20-30 micrometer fingers produced with nanoparticle-based pastes. Double printing achieves SHJ device efficiencies exceeding 20%, the highest reported for industrial solar cell precursors using this technology. These findings highlight the potential of complex Ag inks as a sustainable alternative to particle-based pastes, reducing Ag consumption and processing temperatures without compromising efficiency.

14 SOLAR ENERGY↗

Large-Scale Synthesis of Semiconducting Cu(In,Ga)Se2 Nanoparticles for Screen Printing Application

During the last few decades, the interest over chalcopyrite and related photovoltaics has been growing due the outstanding structural and electrical properties of the thin-film Cu(In,Ga)Se2 photoabsorber. More recently, thin film deposition through solution processing has gained increasing attention from the industry, due to the potential low-cost and high-throughput production. To this end, the elimination of the selenization procedure in the synthesis of Cu(In,Ga)Se2 nanoparticles with following dispersion into ink formulations for printing/coating deposition processes are of high relevance. However, most of the reported syntheses procedures give access to tetragonal chalcopyrite Cu(In,Ga)Se2 nanoparticles, whereas methods to obtain other structures are scarce. Herein, we report a large-scale synthesis of high-quality Cu(In,Ga)Se2 nanoparticles with wurtzite hexagonal structure, with sizes of 10–70 nm, wide absorption in visible to near-infrared regions, and [Cu]/[In + Ga] ≈ 0.8 and [Ga]/[Ga + In] ≈ 0.3 metal ratios. The inclusion of the synthesized NPs into a water-based ink formulation for screen printing deposition results in thin films with homogenous thickness of ≈4.5 µm, paving the way towards environmentally friendly roll-to-roll production of photovoltaic systems.

36 MATERIALS SCIENCE↗

High-Performance Screen-Printed Thermoelectric Films on Fabrics

Printing techniques could offer a scalable approach to fabricate thermoelectric (TE) devices on flexible substrates for power generation used in wearable devices and personalized thermo-regulation. However, typical printing processes need a large concentration of binder additives, which often render a detrimental effect on electrical transport of the printed TE layers. Here, we report scalable screenprinting of TE layers on flexible fiber glass fabrics, by rationally optimizing the printing inks consisting of TE particles (p-type Bi 0.5 Sb 1.5 Te 3 or n-type Bi 2 Te 2.7 Se 0.3 ), binders, and organic solvents. We identified a suitable binder additive, methyl cellulose, which offers suitable viscosity for printability at a very small concentration (0.45–0.60 wt.%), thus minimizing its negative impact on electrical transport. Following printing, the binders were subsequently burnt off via sintering and hot pressing. We found that the nanoscale defects left behind after the binder burnt off became effective phonon scattering centers, leading to low lattice thermal conductivity in the printed n-type material. With the high electrical conductivity and low thermal conductivity, the screen-printed TE layers showed high room-temperature ZT values of 0.65 and 0.81 for p-type and n-type, respectively.

36 MATERIALS SCIENCE↗

Voltammetric determination of vitamin B{sub 6} (pyridoxine) at a graphite screen-printed electrode modified with graphene oxide/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposite

The preparation and study of electrochemical properties of a graphite screen-printed electrode (SPE) modified with the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} (GO is graphene oxide) nanocomposites are described. The morphologies of the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposites were examined by scanning electron microscopy. The electrochemical oxidation of vitamin B{sub 6} (pyridoxine) on SPE modified with the GO/Fe{sub 3}O{sub 4}@SiO{sub 2} nanocomposite was investigated by cyclic voltammetry, differential pulse voltammetry, and chronoamperometry. Under optimum conditions (pH 7.0), the vitamin B{sub 6} oxidation at the surface of the modified SPE occurs at a potential about 190 mV less positive than that at the unmodified SPE. A linear voltammetric response for vitamin B{sub 6} was obtained in the concentration range 1.0•10 {sup 6}—9.0•10 {sup 4} mol L{sup –1} with a detection limit of 5.2•10 {sup 7} mol L{sup –1} using differential pulse voltammetry. The developed sensor was also successfully applied for determination of trace level of vitamin B{sub 6} in both the standard vitamin B{sub 6} sample and biological samples (urine).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Communication—Improving Intermediate-Temperature Performance of a Screen-Printed LSCF Cathode with Infiltrated LSCF Nanoparticles

Here, the present study investigates the mass loading effect of an infiltrated La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) nanoparticles (NPs) catalyst on the area-specific polarization resistance (Rp) of a screen-printed porous LSCF cathode for solid oxide fuel cells. The results show that R p of the LSCF-NPs decorated LSCF cathode can be substantially reduced by as much as 89.3% after a single-step impregnation of 1.5 M nitrate solution containing La:Sr:Co:Fe = 0.6:0.4:0.2:0.8 with a mass loading of 3 wt%.

25 ENERGY STORAGE↗

Development of Low-Cost, Crack-Tolerant Metallization Using Screen Printing

One of the ways to reduce the cost of solar electricity to 3/kWh, thus reaching parity with fossil-fuel-based generation, is to reduce the degradation rate of solar modules and extend their lifetime well beyond 30 years. The extended module lifetime in turn can positively influence the financial model and the bankability of utility-scale PV projects. Today, the highest-riskpriority solar module degradation mechanism is what is known as hot spots, often induced by cell cracks. In order to address this degradation mechanism, we make use of low-cost, multi-walled carbon nanotubes embedded in commercial screen-printable silver pastes. When the carbon nanotubes are properly functionalized and appropriately incorporated into commercial silver pastes, the resulting metal contacts on solar cells, after screen-printing and firing, show exceptional fracture toughness. These composite metal contacts possess increased ductility, electrical gap-bridging capability up to 50 um, and 'self-healing' to regain electrical continuity even after cycles of complete electrical failure under extreme strain.

14 SOLAR ENERGY↗

Method for formation of high quality back contact with screen-printed local back surface field

A thin silicon solar cell having a back dielectric passivation and rear contact with local back surface field is described. Specifically, the solar cell may be fabricated from a crystalline silicon wafer having a thickness from 50 to 500 micrometers. A barrier layer and a dielectric layer are applied at least to the back surface of the silicon wafer to protect the silicon wafer from deformation when the rear contact is formed. At least one opening is made to the dielectric layer. An aluminum contact that provides a back surface field is formed in the opening and on the dielectric layer. The aluminum contact may be applied by screen printing an aluminum paste having from one to 12 atomic percent silicon and then applying a heat treatment at 750 degrees Celsius.

Rohatgi, Ajeet↗

Novel Process for Screen-Printed Selective Area Front Polysilicon Contacts for TOPCon Cells Using Laser Oxidation

The efficiency potential of double-side tunnel oxide passivated contact (DS-TOPCon) solar cells is limited by parasitic absorption in the front poly-Si layer, despite excellent passivation and high V OC . The use of patterned poly-Si only under the front metal grid lines can significantly reduce the parasitic absorption loss without sacrificing voltage. In this work, we demonstrate a simple, manufacturing-friendly method of patterning the front poly-Si using a nanosecond UV (355 nm) laser. We found that with laser powers ≥3 W at a 400 mm/s scan speed, an estimated 1–4 nm thick stoichiometric SiO 2 layer was grown on TOPCon. This served as a mask for KOH-etching of 200 nm poly-Si, allowing for patterning of poly-Si fingers required for selective TOPCon. While laser powers above 3 W caused substantial deterioration in passivation quality, the resulting damage in J 0 was largely recovered by subsequent PECVD SiN x deposition. At 3 W, the full area J 0 was found to be 36.8 fA·cm –2 . Furthermore, this translates to 1.68 fA·cm –2 for 4.48% coverage from the wing area of the polyfinger lines (100 lines–100 μm wide and 30 μm metal) contributing to a total front J 0 of ~10 fA·cm –2 , well suited for 25% efficient solar cells

42 ENGINEERING↗

Investigation of Local Parameters of PERC Solar Cells Metallized with Screen Printed Cu-Paste

For 40 TW of PV required to transition our planet to 100% renewables, the silver (Ag) should disappear from PV production. Advantages of copper (Cu) over silver (Ag) include: 1) bulk Cu has a similar conductivity to Ag (1.7 one millionth O-cm for Cu, 1.6 one millionth O-cm for Ag, and 2) Cu is -100 times cheaper than Ag, making it an excellent potential replacement. Problems associated with copper contacts include: 1) easy oxidation, and 2) diffusion into the Si cell and recombination activity. To summarize: 1) Rs map shows some regions with very high Rs, indicating no contact in those areas; 2) the histogram shows the peak Rs -5 ohm.cm2, which explains the high FF loss due to Rs; and 3) DLIT indicates non-uniformity in J01 and J02.

copper↗