SEARCH · Search NASA

Results for “braiding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Effects of Yarn Crimping on Braided Composite Design Allowables

Braided composite materials are currently being evaluated for wing skin stiffeners on commercial aircraft. These carbon-fiber/epoxy materials allow for low-cost manufacturing while maintaining high strength-to-weight and stiffness-to-weight ratios. The proposed braid architecture consists of axial carbon fiber yarns and braider carbon fiber yarns making 60 deg to 70 deg angles with respect to the axial yarns. These 2-D triaxial braids are produced as long, continuous tubes, which are flattened, cut, and stacked to produce the desired part thickness and shape. When infiltrated with epoxy resin and cured under a compaction pressure, the fiber yarns become crimped, allowing for higher fiber packing. Although high fiber packing is desirable, yarn crimping (especially in the axial fiberyarns) is undesirable. Significant axial yarn crimp angles (greater than 10 deg) have been measured in braided composites. Comparable levels of crimping have been found to produce significant compressive strength reductions in laminated composites consisting of planar fiber sheets. Thus, axial yarn crimping is suspected of producing significant reductions in compressive strength allowables for braided composites. The objective of this research is to quantify the reduction in compressive strength as a function of axial yarn crimp severity. Since crimp severity can be reduced by lowering the compaction pressure during curing, the resulting compressive strengths may be used to determine optimum processing conditions. A 'cure-on-the-loom' manufacturing process was developed to produce braided composites with controlled levels of crimping. This method allowed for controlled levels of tension to be placed on the axial yarns and maintained during the curing process. With increasing tension, the crimp severity in the axial yarns was reduced. Thus, varying crimp severities were produced ranging from conventional levels (greater than 10 deg) to virtually straight axial yarns. Test results indicate that a 30% increase in compressive strength is obtainable by eliminating axial yarn crimping. Further compression testing is underway to quantify the relationship between crimp severity and compressive strength. Additional testing is planned to investigate the effect of crimping on the open-hole compressive strength, often considered a more significant design allowable.

Adams, Dan↗

NASA NTRS1995

Evaluation of Braided Stiffener Concepts for Transport Aircraft Wing Structure Applications

Braided composite materials have potential for application in aircraft structures. Stiffeners, wing spars, floor beams, and fuselage frames are examples where braided composites could find application if cost effective processing and damage requirements are met. Braiding is an automated process for obtaining near-net shape preforms for fabrication of components for structural applications. Previous test results on braided composite materials obtained at NASA Langley indicate that damage tolerance requirements can be met for some applications. In addition, the braiding industry is taking steps to increase the material through-put to be more competitive with other preform fabrication processes. Data are presented on the compressive behavior of three braided stiffener preform fabric constructions as determined from individual stiffener crippling test and three stiffener wide panel tests. Stiffener and panel fabrication are described and compression data presented for specimens tested with and without impact damage. In addition, data are also presented on the compressive behavior of the stitched stiffener preform construction currently being used by McDonnell Douglas Aerospace in the NASA ACT wing development program.

Deaton, Jerry W.↗

DOE OSTI2020

Systems and methods for liner braiding and resin application

A method of selecting a braid configuration for a braided liner. The method includes calculating a size ratio based on the smallest first diameter and the largest second diameter of the liner and selecting a braid material having a tensile strength. The method further includes calculating a strength ratio based on the tensile strength of the braid material and a selected target strength threshold for the braided liner and determining an optimal braid angle for the smallest first diameter portions of the liner based on the calculated size ratio.

Wexler, Jason Stein↗

DOE OSTI2021

Systems and methods for liner braiding and resin application

A method of making a tank for storing fluid that includes generating a resinated braid layer on an elongated liner having a plurality of successively alternating rigid and flexible portions along the length of the liner. Generating the resinated braid layer on the liner includes feeding the liner into a braiding machine and applying resin to a plurality of fibers during a braiding process to generate a resinated plurality of fibers and generating, over a length of the liner, by the braiding machine, the resinated braid layer defined by the resinated plurality of fibers.

Wexler, Jason Stein↗

DOE OSTI2021

Engineering hybrid textile braids for tendon and ligament repair application

Abstract Challenges involving tendon and ligament repair have motivated the investigation of new strategies to improve clinical outcomes. These have been mainly based on polymer constructs, which may be non‐biodegradable or biodegradable. The former typically fails due to lack of device integration and the latter demands a complex balance between biodegradability and tissue ingrowth, often failing due to insufficient mechanical properties. This work presents the development of hybrid braids based on polyethylene terephthalate (PET) and polylactic acid (PLA) yarns. A textile technique was used to fabricate braids based on 16 multifilament yarns of varying PLA/PET composition. The composition was varied to maximize biodegradability while ensuring mechanical performance. The braids' morphology, physical and mechanical properties were characterized. As production parameters and architecture were maintained, the braids exhibited similar porosity and wicking ability. The breaking force and stiffness decreased significantly as the number of PLA yarns increased, although strain levels remained constant. Braids containing 10 and 12 PET yarns (out of the total 16 yarns) demonstrated good creep and force‐relaxation behavior, as well as resistance to cyclic loading. These compositions were selected for future work, to be assembled into more elaborate structures to mimic the fibrous organization and tensile properties of different tendons/ligaments.

Peixoto, Tânia↗

DOE OSTI2024

Geometric representations of braid and Yang–Baxter gates

Brick-wall circuits composed of the Yang–Baxter gates are integrable. It becomes an important tool to study the quantum many-body system out of equilibrium. To put the Yang–Baxter gate on quantum computers, it has to be decomposed into the native gates of quantum computers. It is favorable to apply the least number of native two-qubit gates to construct the Yang–Baxter gate. We study the geometric representations of all X-type braid gates and their corresponding Yang–Baxter gates via the Yang–Baxterization. We find that the braid and Yang–Baxter gates can only exist on certain edges and faces of the two-qubit tetrahedron. We identify the parameters by which the braid and Yang–Baxter gates are the Clifford gate, the matchgate, and the dual-unitary gate. The geometric representations provide the optimal decompositions of the braid and Yang–Baxter gates in terms of other two-qubit gates. We also find that the entangling powers of the Yang–Baxter gates are determined by the spectral parameters. Our results provide the necessary conditions to construct the braid and Yang–Baxter gates on quantum computers.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1991

Mechanical properties of 2D and 3D braided textile composites

The purpose of this research was to determine the mechanical properties of 2D and 3D braided textile composite materials. Specifically, those designed for tension or shear loading were tested under static loading to failure to investigate the effects of braiding. The overall goal of the work was to provide a structural designer with an idea of how textile composites perform under typical loading conditions. From test results for unnotched tension, it was determined that the 2D is stronger, stiffer, and has higher elongation to failure than the 3D. It was also found that the polyetherether ketone (PEEK) resin system was stronger, stiffer, and had higher elongation at failure than the resin transfer molding (RTM) epoxy. Open hole tension tests showed that PEEK resin is more notch sensitive than RTM epoxy. Of greater significance, it was found that the 3D is less notch sensitive than the 2D. Unnotched compression tests indicated, as did the tension tests, that the 2D is stronger, stiffer, and has higher elongation at failure than the RTM epoxy. The most encouraging results were from compression after impact. The 3D braided composite showed a compression after impact failure stress equal to 92 percent of the unimpacted specimen. The 2D braided composite failed at about 67 percent of the unimpacted specimen. Higher damage tolerance is observed in textiles over conventional composite materials. This is observed in the results, especially in the 3D braided materials.

Norman, Timothy L.↗

NASA NTRS1993

Mechanical properties of triaxially braided composites - Experimental and analytical results

This paper investigates the unnotched tensile properties of two-dimensional (2D) triaxial braid-reinforced composites both experimentally and analytically. The materials are graphite fibers in an epoxy matrix. Three different reinforcing fiber architectures were considered. There were considerable differences in the observed elastic constants from different size strain gage and extensometer readings. Larger strain gages gave more consistent results and correlated better with the extensometer readings. Experimental strains correlated reasonably well with analytical predictions in the longitudinal, 0 deg, fiber direction but not in the transverse direction. Tensile strength results were not always predictable even in reinforcing directions. Minor changes in braid geometry led to disproportionate strength variations. The unit cell structure of the triaxial braid was discussed with the assistance of computer analysis of the microgeometry. Photomicrographs of braid geometry were used to improve upon the computer graphics representations of unit cells. These unit cells were used to predict the elastic moduli with various degrees of sophistication. The simple and the complex analyses were generally in agreement, but none adequately matched the experimental results for all the braids.

Masters, John E.↗

NASA NTRS1995

Method and apparatus for three dimensional braiding

A machine for three-dimensional braiding of fibers is provided in which carrier members travel on a curved, segmented and movable braiding surface. The carrier members are capable of independent, self-propelled motion along the braiding surface. Carrier member position on the braiding surface is controlled and monitored by computer. Also disclosed is a yarn take-up device capable of maintaining tension in the braiding fiber.

Farley, Gary L.↗

NASA NTRS1997

Method and apparatus for three dimensional braiding

Farley, Gary L.↗

NASA NTRS2008

Full-field Strain Methods for Investigating Failure Mechanisms in Triaxial Braided Composites

Composite materials made with triaxial braid architecture and large tow size carbon fibers are beginning to be used in many applications, including composite aircraft and engine structures. Recent advancements in braiding technology have led to commercially viable manufacturing approaches for making large structures with complex shape. Although the large unit cell size of these materials is an advantage for manufacturing efficiency, the fiber architecture presents some challenges for materials characterization, design, and analysis. In some cases, the static load capability of structures made using these materials has been higher than expected based on material strength properties measured using standard coupon tests. A potential problem with using standard tests methods for these materials is that the unit cell size can be an unacceptably large fraction of the specimen dimensions. More detailed investigation of deformation and failure processes in large unit cell size triaxial braid composites is needed to evaluate the applicability of standard test methods for these materials and to develop alternative testing approaches. In recent years, commercial equipment has become available that enables digital image correlation to be used on a more routine basis for investigation of full field 3D deformation in materials and structures. In this paper, some new techniques that have been developed to investigate local deformation and failure using digital image correlation techniques are presented. The methods were used to measure both local and global strains during standard straight-sided coupon tensile tests on composite materials made with 12 and 24 k yarns and a 0/+60/-60 triaxial braid architecture. Local deformation and failure within fiber bundles was observed, and this local failure had a significant effect on global stiffness and strength. The matrix material had a large effect on local damage initiation for the two matrix materials used in this investigation. Premature failure in regions of the unit cell near the edge of the straight-sided specimens was observed for transverse tensile tests in which the braid axial fibers were perpendicular to the specimen axis and the bias fibers terminated on the cut edges in the specimen gage section. This edge effect is one factor that could contribute to a measured strength that is lower than the actual material strength in a structure without edge effects.

Littell, Justin D.↗

NASA NTRS2010

Modification of a Macromechanical Finite-Element Based Model for Impact Analysis of Triaxially-Braided Composites

A macro level finite element-based model has been developed to simulate the mechanical and impact response of triaxially-braided polymer matrix composites. In the analytical model, the triaxial braid architecture is simulated by using four parallel shell elements, each of which is modeled as a laminated composite. For the current analytical approach, each shell element is considered to be a smeared homogeneous material. The commercial transient dynamic finite element code LS-DYNA is used to conduct the simulations, and a continuum damage mechanics model internal to LS-DYNA is used as the material constitutive model. The constitutive model requires stiffness and strength properties of an equivalent unidirectional composite. Simplified micromechanics methods are used to determine the equivalent stiffness properties, and results from coupon level tests on the braided composite are utilized to back out the required strength properties. Simulations of quasi-static coupon tests of several representative braided composites are conducted to demonstrate the correlation of the model. Impact simulations of a represented braided composites are conducted to demonstrate the capability of the model to predict the penetration velocity and damage patterns obtained experimentally.

Goldberg, Robert K.↗

NASA NTRS2011

Approaches for Tensile Testing of Braided Composites

For angleply composites, lamina tension and compression strengths are commonly determined by applying classical lamination theory to test data obtained from testing of angleply composite specimens. For textile composites such as 2D triaxial braids, analysis is more complex and standard test methods do not always yield reliable strength measurements. This paper describes recent research focused on development of more reliable tensile test methods for braided composites and presents preliminary data for various approaches. The materials investigated in this work have 0deg+/-60 2D triaxial braid architecture with nearly equal fiber volume fraction in each of the three fiber directions. Flat composite panels are fabricated by resin transfer molding (RTM) using six layers of the braided preform aligned along the 0deg fiber direction. Various epoxy resins are used as matrix materials. Single layer panels are also fabricated in order to examine local variations in deformation related to the braid architecture. Specimens are cut from these panels in the shape of standard straight-sided coupons, an alternative bowtie geometry, and an alternative notched geometry. Axial tensile properties are measured using specimens loaded along the 0deg fiber direction. Transverse tensile properties are measured using specimens loaded perpendicular to the 0deg fibers. Composite tubes are also fabricated by RTM. These tubes are tested by internal pressurization using a soft rubbery material sealed between the inside diameter of the tube and the load fixtures. The ends of the tube are unconstrained, so the primary load is in the hoop direction. Tubes are fabricated with the 0deg fibers aligned along the tube axis by overbraiding the preform on a mandrel. Since the loading is in the hoop direction, testing of the overbraided tube provides a measure of transverse tensile strength. Previous work has indicated that straight-sided coupons yield a transverse tensile strength that is much lower than the expected material strength because of premature edge-initiated failure. Full-field strain measured during transverse tensile tests clearly showed accumulation of edge damage prior to failure. In the current work, high speed video and testing of single layer specimens are used to investigate potential failure mechanisms in more detail. High speed video clearly shows the edge initiation in six layer transverse tensile test coupons. Specimens with the bowtie geometry and the notched geometry minimize this edge effect and yield significantly higher transverse tensile strength values compared to the straight-sided coupons. However, bowtie and notched specimens geometries are not ideal because of the non-uniform stress and strain fields in the region of failure. Testing of tubes using internal pressurization eliminates edge-initiated failure and provides a more uniform state of stress and strain. Preliminary results indicate that bowtie, notched, and tube specimens yield comparable values for transverse tensile strength and that these values are much higher than the strength measured using a straight-sided coupon.

Roberts, Gary D.↗

NASA NTRS2012

Characterization and Analysis of Triaxially Braided Polymer Composites under Static and Impact Loads

In order to design impact resistant aerospace components made of triaxially-braided polymer matrix composite materials, a need exists to have reliable impact simulation methods and a detailed understanding of the material behavior. Traditional test methods and specimen designs have yielded unrealistic material property data due to material mechanisms such as edge damage. To overcome these deficiencies, various alternative testing geometries such as notched flat coupons have been examined to alleviate difficulties observed with standard test methods. The results from the coupon level tests have been used to characterize and validate a macro level finite element-based model which can be used to simulate the mechanical and impact response of the braided composites. In the analytical model, the triaxial braid unit cell is approximated by using four parallel laminated composites, each with a different fiber layup, which roughly simulates the braid architecture. In the analysis, each of these laminated composites is modeled as a shell element. Currently, each shell element is considered to be a smeared homogeneous material. Simplified micromechanics techniques and lamination theory are used to determine the equivalent stiffness properties of each shell element, and results from the coupon level tests on the braided composite are used to back out the strength properties of each shell element. Recent improvements to the model include the incorporation of strain rate effects into the model. Simulations of ballistic impact tests have been carried out to investigate and verify the analysis approach.

Goldberg, Robert K.↗

NASA NTRS2015

Experimental and Numerical Analysis of Triaxially Braided Composites Utilizing a Modified Subcell Modeling Approach

A combined experimental and analytical approach was performed for characterizing and modeling triaxially braided composites with a modified subcell modeling strategy. Tensile coupon tests were conducted on a [0deg/60deg/-60deg] braided composite at angles of 0deg, 30deg, 45deg, 60deg and 90deg relative to the axial tow of the braid. It was found that measured coupon strength varied significantly with the angle of the applied load and each coupon direction exhibited unique final failures. The subcell modeling approach implemented into the finite element software LS-DYNA was used to simulate the various tensile coupon test angles. The modeling approach was successful in predicting both the coupon strength and reported failure mode for the 0deg, 30deg and 60deg loading directions. The model over-predicted the strength in the 90deg direction; however, the experimental results show a strong influence of free edge effects on damage initiation and failure. In the absence of these local free edge effects, the subcell modeling approach showed promise as a viable and computationally efficient analysis tool for triaxially braided composite structures. Future work will focus on validation of the approach for predicting the impact response of the braided composite against flat panel impact tests.

Micromechanics↗

NASA NTRS2015

Experimental and Numerical Analysis of Triaxially Braided Composites Utilizing a Modified Subcell Modeling Approach

A combined experimental and analytical approach was performed for characterizing and modeling triaxially braided composites with a modified subcell modeling strategy. Tensile coupon tests were conducted on a [0deg/60deg/-60deg] braided composite at angles [0deg, 30deg, 45deg, 60deg and 90deg] relative to the axial tow of the braid. It was found that measured coupon strength varied significantly with the angle of the applied load and each coupon direction exhibited unique final failures. The subcell modeling approach implemented into the finite element software LS-DYNA was used to simulate the various tensile coupon test angles. The modeling approach was successful in predicting both the coupon strength and reported failure mode for the 0deg, 30deg and 60deg loading directions. The model over-predicted the strength in the 90deg direction; however, the experimental results show a strong influence of free edge effects on damage initiation and failure. In the absence of these local free edge effects, the subcell modeling approach showed promise as a viable and computationally efficient analysis tool for triaxially braided composite structures. Future work will focus on validation of the approach for predicting the impact response of the braided composite against flat panel impact tests.

Polymer Matrix Composites↗

DOE OSTI2020

Quantifying the effect of tow architecture variability on the performance of biaxially braided composite tubes

Targeted experiments are performed with stereoscopic digital image correlation to quantify the effect of irregular braid structure on the local surface mechanical response of carbon-fiber reinforced epoxy composite tubes. Virtual models comparing both nonuniform and uniform tow structure of the outer braid of each specimen are integrated into numerical simulations similar to experiments. Experimental and numerical results agree well. Statistical tests are used to support correlations between as-manufactured braid variation ranges to local increases in stress up to 18% compared to an ideal, uniform structure in the elastic regime. Results support improved manufacturing and modeling efforts of defect sensitive braided composites.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Consolidation of Braided Carbon Fiber/ Thermoplastic Tubes by Induction Heating

Thermoplastic composites have experienced renewed enthusiasm within the U.S. aerospace industry, due in part to opportunities for rapidly manufacturing large structures. Unlike the lengthy cure cycles required by thermosets, the thermoplastic matrix prepreg requires only heat and pressure to consolidate consecutive layers of material; with sufficient inter-ply contact time to develop a strong interface. The manufacturing requirements for thermoplastics provide manufacturing flexibility and of particular interest are in-situ consolidation processes; i.e consolidation during layup on a tool. In-situ consolidation removes the time-consuming and costly secondary processing step of autoclave or press consolidation. Process variables which contribute to laminate quality include temperature, heat transfer, inter-ply contact time, and consolidation pressure. Most of the work to date related to in-situ consolidation has been in conjunction with automated fiber placement (AFP), where prepreg tows are consolidated when placed on the tool. Considering this process for a braided structure adds complexity relative to AFP due to the rapid lay-down rate of the braider and simultaneous placement of a multiple prepreg tows. Processes considered for consolidation during AFP could not be applied to a braided part. Alternatively, a fully braided preform could be consolidated on the tool using well established thermoplastic welding techniques. The goal of this effort was to evaluate the effectiveness of induction welding to consolidate braided carbon fiber/thermoplastic composite tubes up to eight plies in thickness. The manufacturing process, thermal characterization, and initial mechanical property data of the consolidated tubes are reported.

In-situ consolidation, induction heating/welding, ↗