Search NASA⌕ Search

SEARCH · Search NASA

Results for “bulk absorber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Analysis, design, and test of acoustic treatment in a laboratory inlet duct

A suppression prediction program based on the method of modal analysis for spinning mode propagation in a circular duct was used in the analytical design of optimized, multielement, Kevlar bulk-absorber treatment configurations for an inlet duct. The NASA-Langley ANRL anechoic chamber using the spinning mode synthesizer as a sound source was used to obtain in-duct spinning mode measurements, radial mode measurements, and far-field traverses, as well as aerodynamic measurements. The measured suppression values were compared to predicted values, using the in-duct, forward-traveling, radial-mode content as the source for the prediction. The performance of the treatment panels was evaluated from the predicted and measured data. Although experimental difficulties were encountered at the design condition, sufficient information was obtained to confirm the expectation that it is the panel impedance components which are critical to suppression at a single frequency, not the particular construction materials. The agreement obtained between measurement and prediction indicates that the analytical program can be used as an accurate, reliable, and useful design tool.

Kraft, R. E.↗
NASA NTRS1979

Acoustic behavior of a fibrous bulk material

A semiempirical model is presented describing the acoustic behavior of Kevlar 29, a bulk absorbing material. The model is based on an approximate solution to the one-dimensional equations representing conservation of fluctuating mass, momentum and energy. By treating the material as a momentum sink, theoretical expressions of the material complex propagation constants and characteristic impedance were derived in terms of a single constant. Evaluating the constant at a single frequency for a particular specimen, excellent agreement between prediction and measurement was achieved for a large range of sound frequencies and material porosities and thicknesses. Results show that Kevlar 29 absorbs sound efficiently even at low frequencies. This is explained in terms of a frequency dependent material phase speed.

Hersh, A. S.↗
NASA NTRS1983

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine as measured in the NASA-Ames 40 x 80 foot wind tunnel

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine was investigated in the NASA-Ames 40 x 80 ft wind tunnel. Four inlet designs representative of those found in commercial service were evaluated at a forward velocity of 80 kn. The inlet designs considered were selected to evaluate the importance of circumferential static pressure distortion (SPD) for a diffusing sound suppressing inlet and throat Mach number (Mth) for a hardwall inlet on the acoustic characteristics of the JT15D engine. Several speed points were studied simulating the operating conditions spanning approach to take-off. Results demonstrated that the dependency of the forward radiated noise on inlet aerodynamic design parameters was significant (about 5 dB) for the range of SPD (0.1-3.0%) and Mth (0.3-0.6) tested. The performance of the bulk absorber acoustic treatment used in the diffusing sound suppressing inlet is also discussed.

Holm, R. G.↗
NASA NTRS1999

Advanced Turbofan Duct Liner Concepts

The Advanced Subsonic Technology Noise Reduction Program goal is to reduce aircraft noise by 10 EPNdB by the year 2000 relative, to 1992 technology. The improvement goal for nacelle attenuation is 25% relative to 1992 technology by 1997 and 50% by 2000. The Advanced Turbofan Duct Liner Concepts Task work by Boeing presented in this document was in support of these goals. The basis for the technical approach was a Boeing study conducted in 1993-94 under NASA/FAA contract NAS1-19349, Task 6, investigating broadband acoustic liner concepts. As a result of this work, it was recommended that linear double layer, linear and perforate triple layer, parallel element, and bulk absorber liners be further investigated to improve nacelle attenuations. NASA LaRC also suggested that "adaptive" liner concepts that would allow "in-situ" acoustic impedance control also be considered. As a result, bias flow and high-temperature liner concepts were also added to the investigation. The major conclusion from the above studies is that improvements in nacelle liner average acoustic impedance characteristics alone will not result in 25% increased nacelle noise reduction relative to 1992 technology. Nacelle design advancements currently being developed by Boeing are expected to add 20-40% more acoustic lining to hardwall regions in current inlets, which is predicted to result in and additional 40-80% attenuation improvement. Similar advancements are expected to allow 10-30% more acoustic lining in current fan ducts with 10-30% more attenuation expected. In addition, Boeing is currently developing a scarf inlet concept which is expected to give an additional 40-80% attenuation improvement for equivalent lining areas.

Bielak, Gerald W.↗
NASA NTRS1999

High Temperature Acoustic Liner Technology

This paper describes work currently in progress at Langley on liner concepts that employ structures that may be suitable for broadband exhaust noise attenuation in high speed flow environments and at elevated temperatures characteristic of HSCT applications. Because such liners will need to provide about 10 dB suppression over a 2 to 3 octave frequency range, conventional single-degree-of-freedom resonant structures will not suffice. Bulk absorbers have the needed broadband absorption characteristic; however, at lower frequencies they tend to be inefficient.

Parrott, Tony L.↗
NASA NTRS2000

The Alternative Low Noise Fan

A 106 bladed fan with a design takeoff tip speed of 1100 ft/sec was hypothesized as reducing perceived noise because of the shift of the blade passing harmonics to frequencies beyond the perceived noise rating range. A 22 in. model of this Alternative Low Noise Fan, ALNF, was tested in the NASA Glenn 9x 15 Wind Tunnel. 'Me fan was tested with a 7 vane long chord stator assembly and a 70 vane conventional stator assembly in both hard and acoustically treated configurations. In addition a partially treated 7 vane configuration was tested wherein the acoustic material between the 7 long chord stators was made inactive. The noise data from the 106 bladed fan with 7 long chord stators in a hard configuration was shown to be around 4 EPNdB quieter than a low tip speed Allison fan at takeoff and around 5 EPNdB quieter at approach. Although the tone noise behaved as hypothesized, the majority of this noise reduction was from reduced broadband noise related to the large number of rotor blades. This 106 bladed ALNF is a research fan designed to push the technology limits and as such is probably not a practical device with present materials technology. However, a low tip speed fan with around 50 blades would be a practical device and calculations indicate that it could be 2 to 3 EPNdB quieter at takeoff and 3 to 4 EPNdB quieter at approach than the Allison fan. 7 vane data compared with 70 vane data indicated that the tone noise was controlled by rotor wake-stator interaction but that the broadband noise is probably controlled by the interaction of the rotor with incoming flows. A possible multiple pure tone noise reduction technique for a fan/acoustic treatment system was identified. The data from the fully treated configuration showed significant noise reductions over a large frequency range thereby providing a real tribute to this bulk absorber treatment design. The tone noise data with the partially treated 7 vane configuration indicated that acoustic material in the source noise generation region may be more effective than similar material outside of the generation region.

Dittmar, James H.↗
NASA NTRS1997

Acoustic Barrier Facilitates Inlet Noise Measurements for Aft-Dominated Fans

Noise levels for modern high-bypass-ratio subsonic turbofans tend to be aft dominated. That is, the highest flyover noise levels radiate from the fan exit. Measuring fan inlet sound radiation without aft radiation contamination requires selective suppression of the aft noise. In NASA Lewis Research Center's 9- by 15-Foot Low-Speed Wind Tunnel, an acoustic barrier was used to effectively isolate the inlet noise field for a model of an advanced turbofan. This proof-of-concept test was performed on a model turbofan manufactured for NASA Lewis by the Allison Engine Company as part of the Advanced Subsonic Technology program. The 8-cm-thick acoustic barrier was constructed in sections that were joined upon installation. These sections, which were composed of a wood frame with typically 0.64-cm tempered fiberboard skins, extended from the tunnel's floor to its ceiling and had an axial length of 61 cm. On the fan side of the barrier just downstream of the leading edge, the upstream section had an acoustic treatment--a bulk absorber with a perforated metal skin. It had a nominal full height and an axial length of 46 cm. In addition, an elliptical leading edge was faired into the upstream barrier section. The barrier was mounted on tracks on the tunnel floor and ceiling at a sideline distance of 15 cm from the fan nacelle. Tests were made with the barrier leading edge at the fan inlet highlight plane and 15 cm further aft. The barrier extended downstream essentially to the end of the treated tunnel test section.

Source record↗
NASA NTRS2011

Acoustic Absorption in Porous Materials

An understanding of both the areas of materials science and acoustics is necessary to successfully develop materials for acoustic absorption applications. This paper presents the basic knowledge and approaches for determining the acoustic performance of porous materials in a manner that will help materials researchers new to this area gain the understanding and skills necessary to make meaningful contributions to this field of study. Beginning with the basics and making as few assumptions as possible, this paper reviews relevant topics in the acoustic performance of porous materials, which are often used to make acoustic bulk absorbers, moving from the physics of sound wave interactions with porous materials to measurement techniques for flow resistivity, characteristic impedance, and wavenumber.

Kuczmarski, Maria A.↗
NASA NTRS2008

Post Test Evaluation of HSCT Nozzle Acoustic Liner Subcomponents Subjected to a Hot Acoustic Durability Test

The acoustic liner system designed for use in the High Speed Civil Transport (HSCT) was tested in a thermal-acoustic environment. Five ceramic matrix composite (CMC) acoustic tile configurations, five bulk acoustic absorbers, and one thermal protection system design were tested. The CMC acoustic tiles were subjected to two 2 3/4 hr ambient temperature acoustic exposures to measure their dynamic response. One exposure was conducted on the tiles alone and the second exposure included the tiles and the T-foam bulk absorber. The measured tile RMS strains were small. With or without the T-foam absorber, the dynamic strains were below strain levels that would cause damage during fatigue loading. After the ambient exposure, a 75-hr durability test of the entire acoustic liner system was conducted using a thermal-acoustic cycle that approximated the anticipated service cycle. Acoustic loads up to 139 dB/Hz and temperatures up to 1670 F (910 C) were employed during this 60 cycle test. During the durability test, the CMC tiles were exposed to temperatures up to 1780 F and a transient through thickness gradient up to 490 F. The TPS peak temperatures on the hot side of the panels ranged from 750 to 1000 F during the 60 cycles. The through thickness delta T ranged from 450 to 650 F, varying with TPS location and cycle number. No damage, such as cracks or chipping, was observed in the CMC tiles after completion of the testing. However, on tile warped during the durability test and was replaced after 43 or 60 cycles. No externally observed damage was found in this tile. No failure of the CMC fasteners occurred, but damage was observed. Cracks and missing material occurred, only in the fastener head region. No indication of damage was observed in the T-foam acoustic absorbers. The SiC foam acoustic absorber experienced damage after about 43 cycles. Cracking in the TPS occurred around the attachment holes and under a vent. In spite of the development of damage, the TPS maintained its insulative capability throughout the durability test. The durability test results demonstrate damage-tolerant CMC tile, CMC fastener, TPS, and T-foam absorber designs for the combined thermal and acoustic engine nozzle environment.

Verrilli, Michael J.↗
DOE OSTI2025

X-Ray and Electron Spectroscopy of the CdS/(Ag,Cu)(In,Ga)Se 2 Interface With RbF Treatment

The chemical and electronic structure of the CdS/(Ag,Cu)(In,Ga)Se 2 (CdS/ACIGSe) interface for thin-film solar cells, involving an absorber with a bulk [Ag]/([Ag]+[Cu]) (AAC) ratio of 0.06, a state-of-the-art RbF post-deposition treatment (PDT), and a chemical-bath deposited CdS buffer layer, is studied. To gain a detailed and depth-resolved picture of the CdS/ACIGSe interface, synchrotron- and laboratory-based hard X-ray, soft X-ray, and UV photoelectron spectroscopy, inverse photoemission spectroscopy, and X-ray emission spectroscopy are combined. Compared to the bulk of the absorber, a Cu- and Ga-poor ACIGSe surface is found, with a slightly increased AAC ratio. Strong evidence of a Rb–In–Se species (possibly with some Ag) at the absorber surface is compiled, with a corresponding band gap of 2.79 ± 0.12 eV. This finding is in clear contrast to comparable Ag-free Cu(In,Ga)Se 2 absorbers with RbF-PDT. The Rb–In–Se surface species is not removed by the (wet-chemical) CdS deposition process, while some Se diffuses into the CdS layer and segregates at its surface. The CdS buffer layer shows a band gap of 2.48 ± 0.12 eV, and a cliff (≈ -0.4 eV) is determined in the conduction band alignment at the interface between the Rb–In–Se species and the CdS buffer.

36 MATERIALS SCIENCE↗
NASA NTRS1966

Bellows joint absorbs torsional deflections in duct system

Long, thin-walled bellows compressed into a short length absorbs the same amount of torsional deflection as the same tube in full length condition and saves in cost, complexity and space. This bellows has lower torsional spring rate to absorb the bulk of the duct assembly tortional deflections, leaving the other bellows free to absorb axial and angular deflections.

Daniels, C. M.↗
NASA NTRS2005

Drag Measurements of Porous Plate Acoustic Liners

This paper presents the results of direct drag measurements on a variety of porous plate acoustic liners. The existing literature describes numerous studies of drag on porous walls with injection or suction, but relatively few of drag on porous plates with neither injection nor suction. Furthermore, the porosity of the porous plate in existing studies is much lower than typically used in acoustic liners. In the present work, the acoustic liners consisted of a perforated face sheet covering a bulk acoustic absorber material. Factors that were varied in the experiment were hole diameter, hole pattern, face sheet thickness, bulk material type, and size of the gap (if any) between the face sheet and the absorber material.

Wolter, John D.↗
NASA NTRS1979

Acoustical properties of highly porous fibrous materials

Highly porous, fibrous bulk sound absorbing materials are studied with a view toward understanding their acoustical properties and performance in a wide variety of applications including liners of flow ducts. The basis and criteria for decoupling of acoustic waves in the pores of the frame and compressional waves in the frame structure are established. The equations of motion are recast in a form that elucidates the coupling mechanisms. The normal incidence surface impedance and absorption coefficient of two types of Kevlar 29 and an open celled foam material are studied. Experimental values and theoretical results are brought into agreement when the structure factor is selected to provide a fit to the experimental data. A parametric procedure for achieving that fit is established. Both a bulk material quality factor and a high frequency impedance level are required to characterize the real and imaginary part of the surface impedance and absorption coefficient. A derivation of the concepts of equivalent density and dynamic resistance is presented.

Lambert, R. F.↗
NASA NTRS1975

Prediction of Externally Blown Flap Noise and Turbomachinery Strut Noise

Methods were developed for predicting externally blown flap (EBF) noise and turbomachinery strut noise. Noise radiated by under-the-wing and upper-surface-blowing EBF configurations is calculated as a sum of lift dipole noise, trailing edge noise, and jet quadrupole noise. Resulting predictions of amplitudes and spectra generally were in good agreement with data from small-scale models. These data cover a range of exhaust velocity, flap deflection, exhaust nozzle position, exhaust nozzle shape, and ratio of exhaust nozzle diameter to wing chord. A semi-empirical method for predicting dipole noise radiation from a strut with incident turbulence was in good agreement with data. Leading-edge regions made of perforated plate backed by a bulk acoustic absorber achieved up to 7 db reduction of strut noise caused by incident turbulence at high frequencies. Radial turbulence in a turbofan exit duct was found to have a relatively high level associated with the mean velocity defect in the rotor blade wakes. Use of these turbulence spectra and a dipole noise radiation equation gave general prediction of measured aft-radiated sound power caused by a splitter ring in a full-scale fan exit duct.

Fink, M. R.↗
NASA NTRSDate not supplied

The Two-Cavity Method for Characterizing Acoustical Materials—an Interlaboratory Study

This study focuses on understanding the sound absorption characteristics of porous acoustic materials, which are determined by two key parameters independent of material thickness: characteristic impedance and propagation constant. These parameters can be characterized by testing a porous sample concept in a normal incidence impedance tube using either the two-thickness or the two-cavity method. In the two-thickness method, two samples of varying thicknesses are required. In contrast, the two-cavity method requires testing one sample at two different air cavity depths behind the porous material. This method is particularly advantageous for materials that are costly or challenging to fabricate. This interlaboratory study evaluates the variability of characteristic properties determined using the two-cavity method. Porous acoustic materials were additively manufactured and tested in the Liner Technology Facility(LTF)at NASA Langley Research Center and the Mechanics, Acoustics and Dynamics Lab (MADLab) at Michigan Technological University. The characteristic properties derived from various cavity depth combinations were used to predict the surface impedance of the sample with a rigid backing. The prediction was then compared the measured impedance spectrum. It was also found that the combinations of cavity depths can significantly influence the accuracy of the deduced properties.

acoustic liners↗
NASA NTRS1992

Operational strategies for contamination control of composite materials

Composite materials, used on many instruments, are a potential contamination source for sensitive sensors, especially for sensors or detectors cooled below -80 C. It is a well known fact that composite materials absorb water during fabrication, integration, test, and launch activities and desorb this water under vacuum conditions. Water absorption can be divided into two types: shallow water and deep water. Shallow water is generally about 500 A thick on a clean material surface and is easily desorbed under vacuum conditions. Deep water is a function of the material and is absorbed into the bulk of the material. Deep water can outgas for weeks, months, or years, depending on the vent path, the amount of absorbed water, and the temperature of the material. Several operational strategies have been successfully employed on the Wide Field Planetary Camera. The operational strategies include ultradry gaseous nitrogen purge, dew point of less than -80 C, and vacuum bake-out with verification of outgassing rates. The nitrogen purge is instituted during the fabrication phase and is continued through launch activities. Great care is taken to avoid extended periods of time that the material is exposed to the ambient environment (50 percent relative humidity). On-orbit operational strategies include heat-up and cool-down scenarios which allow the deep water to be sufficiently outgassed before cooling the sensors or detectors.

Hansen, Patricia A.↗