Search NASA⌕ Search

SEARCH · Search NASA

Results for “heterojunction silicon solar cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Evaluating the Performance and Reliability of Screen-Printable Fire-Through Copper Paste on PERC Solar Cells

A bifacial silicon heterojunction solar cell demands approximately 210 mg usage of silver paste (9 busbars, 24.5%, bifacial, M6 size wafer). Copper is an excellent alternative to silver: 100x cheaper, similar elecvtrical resistivities, and 1000x more abundant. Successful demonstration of large area selective emitter PERC solar cells using Cu fire-through paste with FF approximately 75% and approximately 19%. Paste chemistry results in oxide-based Cu diffusion barrier, leading to good reliability of the devices: 1000h DHT giving a 3.5% efficiency drop. The additional series resistance still needs to be lowered. Printed and fired cell performance is governed mostly by pFF, especially J02 ; same for DHT degradation. Further improvement in printing and firing optimization for lower series resistance and higher FF.

Ag↗
DOE OSTI2020

Polymeric Electron-Selective Contact for Crystalline Silicon Solar Cells with an Efficiency Exceeding 19%

Carrier-selective contacts have become a prominent path forward toward efficient crystalline silicon (c-Si) photovoltaics. Among the proposed contacting materials, organic materials may offer simplified and low-cost processing compared with typical vacuum deposition techniques. In this paper, branched polyethylenimine (b-PEI) is presented as an electron-transport layer (ETL) for c-Si solar cells. The incorporation of a b-PEI interlayer between c-Si(n) and Al leads to a low contact resistivity of 24 mΩ cm 2 . A silicon heterojunction solar cell integrated with b-PEI is demonstrated achieving a power conversion efficiency of 19.4%, which improves the benchmark efficiency of a c-Si solar cell with an organic ETL. This electron selectivity of b-PEI is attributed to its Lewis basicity, i.e., electron-donating ability, promoting favorable band bending at the c-Si surface for electron transport. Moreover, several other Lewis base polymers perform as efficient ETLs in organic/c-Si hybrid devices, indicating Lewis basicity could be a guideline for future organic ETL design.

14 SOLAR ENERGY↗
NASA NTRS1990

Wide-bandgap epitaxial heterojunction windows for silicon solar cells

It is shown that the efficiency of a solar cell can be improved if minority carriers are confined by use of a wide-bandgap heterojunction window. For silicon (lattice constant a = 5.43 A), nearly lattice-matched wide-bandgap materials are ZnS (a = 5.41 A) and GaP (a = 5.45 A). Isotype n-n heterojuntions of both ZnS/Si and GaP/Si were grown on silicon n-p homojunction solar cells. Successful deposition processes used were metalorganic chemical vapor deposition (MO-CVD) for GaP and ZnS, and vacuum evaporation of ZnS. Planar (100) and (111) and texture-etched - (111)-faceted - surfaces were used. A decrease in minority-carrier surface recombination compared to a bare surface was seen from increased short-wavelength spectral response, increased open-circuit voltage, and reduced dark saturation current, with no degradation of the minority carrier diffusion length.

Landis, Geoffrey A.↗
NASA NTRS1983

Microcrystalline silicon growth for heterojunction solar cells

A total of sixteen runs of e-beam vacuum deposition of p type microcrystalline Si (m-Si) films were attempted on n type or p-n junction single crystalline Si (C-Si) substrates. The m-Si film thickness varied from .15 to .7 um and metal contacts were deposited after plasma hydrogenation. The p-m-Si on n-c-Si structure had a Voc of up to 490 m V while no Voc improvements were observed in the p-m-Si on p-n C-Si structure against p-n controls. Both CFF and Jsc were lower than control. Possible problem areas were interfaced between m-Si and C-si and the back contacts due to lack of sintering for fear of dehydrogenation.

Iles, P. A.↗
NASA NTRS1984

Microcrystalline silicon growth for heterojunction solar cells

A single source of evaporation with B mixed with highly doped Si is used instead of the coevaporation of separate Si and B sources to reduce possible carbon contamination. The results of both the heterojunction or heteroface structures, however, are similar when evaporation is used. The best Voc of the heterojunction is about 460mV and no improvement in Voc in the heteroface structure is observed. Slight Voc degradation occurred. A study of the p m-Si/p c-Si structure showed a negative Voc in many cases. The interface properties between the two materials are such that instead of repelling minority carriers from the substrate carrier, collection actually occurred. Another study of cells made in the part of substrates not covered by n-Si results in performance lower than the controls. This indicates possible substrate degradation in the process.

Iles, P. A.↗
NASA NTRS1984

Microcrystalline silicon growth for heterojunction solar cells

Microcrystalline Si (m-Si) films with a 1.7eV energy bandgap and crystal size of several hundred A were e-beam evaporated on single crystalline Si (c-Si) to form a heterojunction with the substrate, or a window layer to a single crystalline p-n junction (heteroface structure). The goal was to enhance Voc by such uses of the larger bandgap m-Si, with the intriguing prospect of forming heterostructures with exact lattice match on each layer. The heterojunction structure was affected by interface and shunting problems and the best Voc achieved was only 482mV, well below that of single crystal Si homojunctions. The heteroface structure showed promise for some of the samples with p m-Si/p-n structure (the complementary structure did not show any improvement). Although several runs with different deposition conditions were run, the results were inconsistent. Any Voc enhancement obtained was too small to compensate for the current loss due to the extra absorption and poor carrier transport properties of the m-Si film.

Leung, D. C.↗
DOE OSTI2023

From Femtoseconds to Gigaseconds: The SolDeg Project to Analyze and Mitigate the Performance Degradation of a-Si:H/c-Si Heterojunction Solar Cells

We pursued two major projects. In the first, we studied the degradation of a-Si/c-Si Heterojunction cells. We substantially expanded our previously developed SolDeg platform, and incorporated hydrogen into it. We also expanded the capabilities of SolDeg by developing a three channel model for a very efficient way to determine long term junction dynamics. The first main result was that we identified hydrogen drifting away from the interface as a key degradation channel. The second was that we developed and proposed the concept of a “reverse silicon density gradient” in the a-Si layer that had the promise of reducing degradation by up to 80%. In the second project, we studied the degradation of TOPCon solar cells. We again identified a key degradation channel, which in these cells was the formation of pinholes across the oxide layer. We then again were able to develop and to propose a way to dramatically reduce degradation by discovering that tuning the hydrogen concentration forms a sharp and deep minimum of the recombination current.

14 SOLAR ENERGY↗
DOE OSTI2024

Laser‐Sintered Silver Metallization for Silicon Heterojunction Photovoltaic Cells

Herein, a novel metallization technique is reported for crystalline silicon heterojunction (SHJ) solar cells in which silver (Ag) fingers are printed on the SHJ substrates by dispensing Ag nanoparticle‐based inks through a needle and then sintered with a continuous‐wave carbon dioxide (CO 2 ) laser. The impact of the Ag ink viscosity on the line quality and the line resistance is investigated on three Ag inks with different viscosities. Increasing ink viscosity yields higher Ag contact heights, larger aspect ratios, and lower line resistance values. The Ag line height increases from less than a micrometer to ≈18.62 ± 3.48 μm with the increasing viscosity. Photoluminescence imaging shows that the low‐resistance Ag metal contacts obtained do not result in any passivation damage of the SHJ substrate. This is because the wavelength of light emitted from the CO 2 laser (i.e., 10.6 μm) leads to optical absorption in the Ag, but this light is effectively transparent to the transparent conductive oxide film, amorphous silicon films, and crystalline silicon substrate. Bulk resistivity values as low as 6.5 μΩ cm are obtained for the laser‐sintered Ag contact and printed using the Ag ink with the highest viscosity in this work.

Mousumi, Jannatul Ferdous↗
DOE OSTI2022

Microdroplet Electrospray Localized Laser Printing and Sintering of Nanoparticles for Passivating, Carrier-Selective Contacts (Final Technical Report)

In this project, the team used a nanoparticle electrospray laser deposition (NELD) process developed at the University of Central Florida (UCF) to address current limitations of passivating, carrier-selective contact technologies for crystalline silicon (c-Si) photovoltaic (PV) cells. The NELD process was used to print low bulk line resistivity Ag contacts directly onto transparent conductive oxides (TCOs), like indium tin oxide (ITO), for hydrogenated amorphous silicon (a-Si:H) based c-Si heterojunction (SHJ) cells without any subsequent contact firing step needed.

14 SOLAR ENERGY↗
DOE OSTI2024

In-situ hydrogen microstructural characterization of Si heterojunction passivation: Addressing V OC degradation and mitigation pathways

Si heterojunction (SHJ) solar cells have demonstrated record efficiency >27%, approaching the theoretical limit of ≈ 29%, primarily due to best surface/interface defect passivation provided by deposited thin layers of hydrogenated amorphous silicon (a-Si:H). Such excellent surface/interface passivation reduces recombination loss and result in >100 mV improvement of cell open circuit voltage (V OC ) to ≈ 750 mV, thus the cell efficiency. However, fielded SHJ modules exhibit loss of V OC and hence efficiency over time in years, presumably due to degradation related to a-Si:H layers. This adversely affects the technology’s market acceptance, and levelized cost of energy (LCOE). It is hypothesized that the origin of a-Si:H degradation is somehow related to the presence of weak Si–Si bonds and hydrogen in a-Si:H films. The objective of this project is to test this hypothesis by directly measuring chemical and structural changes occurring within SHJ component layers and solar cells. This is achieved by developing an innovative in-situ Fourier transform infrared (FTIR) spectrometry apparatus to monitor hydrogen microstructural changes occurring within amorphous silicon and decipher hydrogen evolution kinetics over time when samples are exposed to heat and/or light stress. These in-situ measured hydrogen microstructural changes are correlated to the changes in effective minority carrier lifetime (τ eff ), implied V OC (iV OC ), surface recombination velocity (S), and cell V OC . These mechanistic understandings will provide critical guidance to mitigate the V OC -driven degradation of SHJ solar cell performance. Passivation optimization and degradation analysis of individual SHJ component structures were achieved through systematic deposition of three symmetric structures and the completed SHJ solar cell structure. The three symmetric structures used were intrinsic a-Si:H [(i)a-Si:H] layers in a bilayer structure, intrinsic and p-type doped stacked layers [(i-p)a-Si:H] representing the front heterojunction in the SHJ cell, and intrinsic and n-typed doped stacked layers [(i-n)a-Si:H] representing the back-side back surface field (BSF) in the SHJ cell. State-of-the-art passivation qualities are demonstrated by a champion iV OC of 740 mV for the (i)a-Si:H layers, and the (i-n)a-Si:H symmetric structure. A 725 mV iV OC is observed for the (i-p)a-Si:H symmetric structure. These symmetric passivated SHJ component structures were subsequently subjected to different accelerated lifetime (ALT) stressors to identify which conditions contribute the most to iV OC degradation. Degradation of the thin (10 nm) (i)a-Si:H passivation layers without any additional overlying layers is minimal; complexity of this study arises due to unavoidable surface oxidation of (i)a-Si:H layer during most of the stress application, which is likely irrelevant for a full SHJ cell configuration with overlying protective layers. The iV OC degradation of symmetric structures is found to occur primarily at the (i-p)a-Si:H passivation stack under dark heat stress with associated hydrogen loss from the (p)a-Si:H layer. An activation energy for increase in S (defect creation) of 0.65 eV can be correlated to the activation energy of ≈ 0.4 eV for hydrogen loss from the (i-p)a-Si:H stack. This also suggests the presence of weakly bonded hydrogen in the (p)a-Si:H films, which effuses out of the film stack at such low activation energy. When light and heat stress are applied together, similar hydrogen loss from (i-p)a-Si:H stack is observed, however, does not appreciably degrade iV OC or increase S. This is an important result and departure from direct correlation between hydrogen loss and defect creation. This perhaps indicates additional defect chemistries or annealing that might be occurring in the presence of light requiring further detailed defect measurements. The full SHJ cell structure used for this project is depicted in Fig.1(d). SHJ cells with an initial V OC ≈ 700 mV were fabricated and subjected to similar ALT stress conditions. Cell V OC is found to degrade the most under dark heat stress and is confirmed by observed hydrogen migration out of the (i-p)a-Si:H stack. However, hydrogen cannot escape from the cell stack, it accumulates near the (p)a-Si:H/ITO contact interface, where ITO acts as a barrier preventing hydrogen loss. Furthermore, light-heat combined stress does not degrade V OC appreciably, confirming the occurrence of a defect annealing process.

14 SOLAR ENERGY↗
DOE OSTI2026

Screen-Printed SHJ Solar Cells with Complex Silver Inks

Metallization using complex metal inks has gained significant research interest due to its cost-effectiveness and ability to achieve performance comparable to traditional nanoparticle pastes. This study introduces the use of complex silver (Ag) inks applied via industrial screen-printing for silicon heterojunction (SHJ) solar cell metallization. The printed Ag lines exhibit a contact resistivity on SHJ tin-doped indium oxide (ITO) surfaces as low as approximately 0.2-12 mO cm2. Photoluminescence imaging reveals minimal surface passivation degradation (iVoc < 3.5 mV), while scanning electron microscopy (SEM) shows a denser structure compared to Ag layer from nanoparticle pastes. The printed Ag grid features thin (approximately 1 micrometer), continuous fingers approximately 100-120 micrometer wide, significantly thinner than conventional approximately 20-30 micrometer fingers produced with nanoparticle-based pastes. Double printing achieves SHJ device efficiencies exceeding 20%, the highest reported for industrial solar cell precursors using this technology. These findings highlight the potential of complex Ag inks as a sustainable alternative to particle-based pastes, reducing Ag consumption and processing temperatures without compromising efficiency.

14 SOLAR ENERGY↗
DOE OSTI2024

Screen-Printed Complex Ag Inks for Si HJT Metallization

Metallization using reactive metal inks has recently attracted significant research interest due to its advantages in cost of materials and manufacturing, while still achieving performance comparable to traditional fire-through particle pastes. Here, we present for the first time the use of reactive silver (Ag) inks via industrial screen-printing and inkjet printing methods for the metallization of different Si surfaces used in tunneling oxide passivating contacts (TOPCon) and Silicon heterojunction (SHJ) solar cells. Printed Ag lines exhibit a conductivity of ~5 Mu O·cm, which is approximately 3 times that of bulk Ag (1.59 µO·cm). The printed metal has a thickness of ~0.5-1.5 Mu m, an order of magnitude smaller than the current fire-through metal finger thickness (~15 Mu m). Contact resistivity measurements of the screen-printed and inkjet-printed samples on a transparent conducting oxide (TCO) surface show a very low value of ~0.2-12 mO·cm 2. Photoluminescence images of the metallized samples demonstrate minimal surface passivation degradation compared to the non-metallized areas (?iVoc <3.5 mV). Scanning electron microscopy images (SEM) reveal the structure of the printed metals on the Si surfaces as porous but much denser than fire-through Ag by nanoparticle paste. In the final presentation, we will showcase our results of printing these reactive Ag inks on high-efficiency heterojunction and TOPCon solar cells with full-area M6 wafers. Additionally, the adhesion of these reactive Ag inks on different Si surfaces according to ASTM D3359-17, as well as the performance of solar cells after standard IEC 61215 freeze/thaw and damp heat tests, will be presented. These new metal inks show promising potential as an alternative to the currently dominant particle-based pastes, offering lower Ag consumption and lower processing temperatures without compromising performance.

heterojunction solar cells↗
NASA NTRS1975

Glass-Si heterojunction solar cells

An increase in efficiency from 2% to over 7% was achieved by a solar cell that used polycrystal silicon heterojunction with SnO2 glass. For Single crystal substrates, efficiencies close to 10% were measured. These cells had the same structures as polycrystalline cells. Work on p+/n heterojunction using In2O3 glass resulted in cells of 3% efficiency on polycrystalline material and 4% efficiency on single crystal material.

Ahrons, R. W.↗
DOE OSTI2020

Electroluminescence Characterization of Recombination in Back Junction Silicon Heterojunction Test Structures: Role of the Inversion Layer

Electroluminescence (EL) characterization technique is used to quantify recombination properties in back junction silicon (Si) heterojunction (HJ) solar cell test structures with interdigitated back contact (IBC) emitters and metal contacts. These test structures are three terminal devices that allow the selective biasing and injection of minority carriers into spatially isolated emitter strips having different widths. This allows the study of minority carriers' current transport, flow, and recombination in these regions, which can, then, be applied to full IBC cells. EL is used to verify that emission is proportional to the minority carriers' concentration in the corresponding regions of the device, thus providing information relevant to minority carriers' collection when compared with laser beam induced current technique in considerably less time and with a higher spatial resolution. Current transport through the inversion layer that occurs due to the band bending at the n crystalline Si and p amorphous Si interface is discussed relying on the distance that minority carriers travel in different configurations and on their diffusion length. Laser defect spots (LDS) were, then, introduced in the emitter regions to analyze the spatial profile of minority carriers as they recombine at the LDS due to their high surface recombination velocity. Ideality factors in different configurations are spatially mapped from EL before and after introducing LDS and are used to show the effect of the inversion layer on the different recombination mechanisms. Current transport through the inversion layer is studied at different biasing conditions and correlated with current transport after LDS.

42 ENGINEERING↗
DOE OSTI2026

Microstructure and Composition of Passivating Interfaces in Silicon Heterojunction Solar Modules Weathered in Different Climates

Sanyo/Panasonic patented silicon heterojunction with intrinsic thin layer (HIT) solar cells in the 1990's, which demonstrated world record photovoltaic (PV) efficiency around 2014 and inspired the newer generations of silicon heterojunction technology (SHJ) as well as the current world record back-contact PV cell designs. The high-quality passivation strategy, utilizing ultra-thin layers of hydrogenated amorphous silicon (a-Si:H), leads to high voltages and long carrier lifetimes, but these qualities may degrade over time as the modules operate outdoors. Here, we investigate local microstructure and composition at the interface layers of cells from HIT modules weathered in a hot, humid climate (Florida, USA) and temperate climate (Colorado, USA) for 10 years. We employ a comprehensive set of high-resolution electron microscopy imaging and spectroscopy to directly resolve structure and composition in these cells down to the nanoscale. We show features such as alignment of the In2O3 transparent conducting oxide and a-Si:H layers on the textured c-Si facets, interfacial oxidation at the a-Si:H/c-Si and In2O3/a-Si:H interfaces, and twinned c-Si resulting from epitaxial growth into the a-Si:H layer. Our results raise potential degradation mechanisms in these outdoor-weathered modules, but the root cause of electrical loss remains uncertain due to the very small changes in aged samples. This study shows that many atomic scale features at the In2O3/a-Si:H/c-Si interfaces are surprisingly robust, and the electrical losses with aging may either be attributed to other pathways or be very sensitive to the subtle chemical and microstructural features observed here.

14 SOLAR ENERGY↗
DOE OSTI2022

UV‐induced degradation of high‐efficiency silicon PV modules with different cell architectures

Abstract Degradation from ultraviolet (UV) radiation has become prevalent in the front of solar cells due to the introduction of UV‐transmitting encapsulants in photovoltaic (PV) module construction. Here, we examine UV‐induced degradation (UVID) in various commercial, unencapsulated crystalline silicon cell technologies, including bifacial silicon heterojunction (HJ), interdigitated back contact (IBC), passivated emitter and rear contact (PERC), and passivated emitter rear totally diffused (PERT) solar cells. We performed UV exposure tests using UVA‐340 fluorescent lamps at 1.24 W·m −2 (at 340 nm) and 45°C through 4.02 MJ·m −2 (2000 h). Our results showed that modern cell architectures are more vulnerable to UVID, leading to a significant power decrease (−3.6% on average; −11.8% maximum) compared with the conventional aluminum back surface field (Al‐BSF) cells (<−1% on average). The power degradation is largely caused by the decrease in short‐circuit current and open‐circuit voltage. A greater power decrease is observed in bifacial cells with rear‐side exposure compared with those with front‐side exposure, indicating that the rear side is more susceptible to UV damage. Secondary ion mass spectroscopy (SIMS) confirmed an increase in hydrogen concentration near the Si/passivation interface in HJ and IBC cells after UV exposure; the excess of hydrogen could result in hydrogen‐induced degradation and subsequently cause higher recombination losses. Additionally, surface oxidation and hot‐carrier damage were identified in PERT cells. Using a spectral‐based analysis, we obtained an acceleration factor of 5× between unpackaged cells (containing a silicon nitride antireflective coating on the front) in the UV test and an encapsulated module (with the front glass and encapsulant blocking 90% of the UV at 294 nm and 353 nm, respectively) in outdoor conditions. From the analytical calculations, we show that a UV‐blocking encapsulant can reduce UV transmission in the module by an additional factor of ~50.

14 SOLAR ENERGY↗
DOE OSTI2021

Optimization of four terminal rear heterojunction GaAs on Si interdigitated back contact tandem solar cells

High-efficiency, four-terminal tandem solar cells composed of thin GaAs films mechanically stacked onto interdigitated back contact silicon solar cells with a glass interlayer are demonstrated. The optimal thickness of the absorber layer of a rear heterojunction GaAs subcell for use in four terminal tandem solar cells was studied. GaAs top cells with absorber layer thicknesses of 1.5, 1.9, 2.3, 2.8, and 3.5 µm were fabricated on glass and mechanically stacked onto interdigitated back-contact Si bottom cells. All tandem cells were found to have efficiencies above 30% under the AM1.5 G spectrum demonstrating a relatively weak sensitivity to thickness in the four-terminal configuration. We found the 2.8 µm absorber layer cell to have the highest top cell and tandem cell efficiency at 26.38% and 32.57%, respectively. Optical modeling with transfer matrix method for the planar top cell and Lambertian light trapping in the textured Si subcell, along with drift-diffusion Hovel equations, were used to show photon recycling enhancement to the effective diffusion length and VOC of the top cell as a result of the low-index glass interlayer.

14 SOLAR ENERGY↗
NASA NTRS1976

A theoretical study of heterojunction and graded band gap type solar cells

The theory of heterojunction and graded bandgap solar cells was studied to help determine the material compositions and device dimensions needed for high efficiency solar cells. Because of the involved analysis of the fundamental equations describing solar cell operation, a general numerical device analysis program was used. A major part of the initial work was involved in modifying an existing silicon solar cell analysis program to account for the unique features of graded bandgap and heterojunction solar cells. The most successful III-V solar cells have so far been constructed in the GaAs and Gal-xAlxAs material systems; this project was concerned with such solar cells. The most efficient solar cell so far evaluated is an abrupt heterojunction cell with a pure AlAs layer at the surface with a GaAs substrate. The predicted efficiency for this cell is slightly larger than that of a graded bandgap Gal-xAlxAs solar cell.

Hauser, J. R.↗