Search NASA⌕ Search

SEARCH · Search NASA

Results for “high explosive experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Improving Chirped Fiber Bragg Grating Resolution for Position-Sensitive Sensors in Shock- and Detonation-Driven Experiments

Chirped fiber Bragg gratings (CFBGs) are robust diagnostic sensors that are widely used to track detonation-driven and shock wave propagation. CFBGs are inscribed with a linearly chirped periodic index of refraction changes that alter the Bragg wavelength along the length of the probe. The light return of each individual Bragg element is captured by a detector at a unique time to map the full reflected spectrum. The CFBG spectrum is measured with a dispersive Fourier transform of the reflected light that temporally stretches the spectrum to increase spatial resolution and make a one-to-one map of the wavelength on a time axis. Here, we propose an improvement of CFBG temporal resolution by incorporating two co-linear laser pulses with orthogonal polarization states and a 5 ns time offset. The two separate signals were split and tracked by two separate detectors. An oscilloscope captured good separation in the signals, and two separate spectrograms were generated and interleaved in the post-processing of the data. This novel technique doubled the CFBG temporal resolution and led to a doubled location resolution. As a proof-of-concept of this technique, the resolution improvement was compared between standard CFBG measurements and the two polarization states method on a position-sensitive CFBG sensor. CFBG resolution doubling will advance sensor capabilities and will have a direct impact on improving capture and analysis in dynamic, high-explosive experiments.

42 ENGINEERING↗

Dynamic Fracture Simulations of Explosively Loaded Cylinders

This report documents the modeling results of high explosive experiments investigating dynamic fracture of steel (AerMet® 100 alloy) cylinders. The experiments were conducted at Lawrence Livermore National Laboratory (LLNL) during 2007 to 2008 [10]. A principal objective of this study was to gain an understanding of dynamic material failure through the analysis of hydrodynamic computer code simulations. Two-dimensional and three-dimensional computational cylinder models were analyzed using the ALE3D multi-physics computer code.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A Preliminary Assessment of the SURF Reactive Burn Model Implementation in FLAG

Properly validated and calibrated reactive burn models (RBM) can be useful engineering tools for assessing high explosive performance and safety. Experiments with high explosives are expensive. Inexpensive RBM calculations are increasingly relied on for predictive analysis for performance and safety. This report discusses the validation of Menikoff and Shaw’s SURF reactive burn model, which has recently been implemented in the FLAG code. The LANL Gapstick experiment is discussed as is its’ utility in reactive burn model validation. Data obtained from pRad for the LT-63 series is also presented along with FLAG simulations using SURF for both PBX 9501 and PBX 9502. Calibration parameters for both explosives are presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling for pRad Explosive Experiments

The hydrodynamics code CTH was used to simulate high-explosive detonations in various geometries to design a planar, high-pressure drive with Taylor wave release for experiments in the proton radiography containment vessel. The most successful geometry is based on a P25 lens with some of its outer diameter and output end removed. Shock planarity was significantly improved relative to an unmodified P25 lens for this case, where its full diameter was not needed, and the calculated timing was adequate to trigger the experiments successfully.

36 MATERIALS SCIENCE↗

Ejected particle size measurement using Mie scattering in high explosive driven shockwave experiments

In this paper, we report on the development of a diagnostic to provide constraints on the size of particles ejected from shocked metallic surfaces. The diagnostic is based on measurements of the intensity of laser light transmitted through a cloud of ejected particles as well as the angular distribution of scattered light, and the analysis of the resulting data is done using the Mie solution. Finally, we describe static experiments to test our experimental apparatus and present initial results of dynamic experiments on Sn targets. Improvements for future experiments are briefly discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Small scale thermal violence experiments for combined insensitive high explosive and booster materials

A small scale cook-off experiment has been designed to provide a violence metric for both booster and IHE materials, singly and in combination. The experiment has a simple, axisymmetric geometry provided by a 10 mm internal diameter cylindrical steel confinement up to 80 mm in length. Heating is applied from one end of the sample length creating pseudo 1-D heating profile and a thermal gradient across the sample(s). At the opposite end of the confinement to the heating block, a machined groove provides a point of rupture that generates a cylindrical fragment. The displacement of the external face of the fragment is detected by Heterodyne Velocimetry. Proof of concept experiments are reported focusing on HMX and TATB formulations, and are described in relation to confinement, ullage and heating profile. The development of a violence metric, based upon fragment velocity records is discussed.

36 MATERIALS SCIENCE↗

Development and modeling for a small-scale, rapidly heated high explosives initiation time (HEIT) experiment

Most small-scale assessments of explosive sensitivity, including the popular drop-weight impact test, convolute thermal and mechanical phenomena to the extent that it has been extremely challenging to decipher how an explosive ignites and propagates reactions. For instance, an impact generates heat through a range of dissipation mechanisms, which can in turn, depending on the reaction rates of the explosive, lead to chemical decomposition. To deconvolute the various contributions to the sub-shock initiation and propagation of explosive reactions, we describe the development and modeling of the High Explosives Initiation Time (HEIT) test - a new, small-scale, high-throughput experiment designed to rapidly heat milligram quantities of energetic materials confined within small diameter steel needles. Specifically, we have modeled and designed a 250 joule pulsed power system capable of rapidly delivering electrical current to the needles, resulting in rapid heat delivery to the sample. In conclusion, the energy deposition rate into the sample is controlled by different transmission line topologies. Modeling in COMSOL is performed to understand the energy required to heat up the explosive sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Detonation performance experiments and modeling for the DAAF-based high explosive PBX 9701

Detonation performance experiments and modeling are reported for the explosive PBX 9701, which is composed of 97% 3,3$\acute{-}$diamino-4,4$\acute{-}$azoxyfurazan (DAAF) and 3% vinylidene uoride-chlorotriuoroethylene copolymer (Kel-F 800) binder by weight. PBX 9701 is a newly-developed reducedsensitivity explosive with increased performance relative to the triaminotrinitrobenzene or TATB-based PBX 9502 while still retaining low sensitivity to mechanical insult. The first detonation performance measurements for this formulation are presented, including front-curvature ratesticks and cylinder expansion test data. Prior shock initiation data is also reviewed. These data are used to develop programmed burn and reactive flow calibrations for existing commonly-used performance models which allow engineering calculations with PBX 9701. The calibration process involves several enhancements relative to conventional approaches including the use of an analytical scaling correlation to speed the calibration process and development of a new methodology to improve the consistency between the programmed burn and reactive model calibration process and the resulting calculations. Overall, PBX 9701 is seen to exhibit improved performance relative to insensitive explosives, with a trinitrotoluene (TNT) equivalence of 1.24. The detonation performance properties are found to be well captured by existing models.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

GEOMETRY OF DAMAGE IN SHOCK LOADED COPPER AND TANTALUM

Cavities of coalesced voids have been found in recovered samples of Tantalum in high-explosive-driven experiments. The boundaries of these cavities are imprinted with details of the coalescence and void growth processes. One way of quantifying these details is to measure the roughness of the surfaces. In this work, we calculate the roughness of 2D cross sections of such cavity surfaces from micrographs by analyzing the images with the box counting technique. Spall plane damage driven by flyer plates in Copper samples is also analyzed. The different length scale regimes found will be discussed.

36 MATERIALS SCIENCE↗

Computational study of TATB

We have performed a computational study of TATB. The study is composed of two parts, one where we perform static T = 0 K calculations with several different DFT functionals, to investigate structural properties and obtain a cold curve. Even though the functionals used in this study give poor results at ambient pressure, they perform much better at compression, when the dominance of the van der Waals’ forces in the binding is replaced by more normal interactions. In particular AM05 gives good results, mainly because it doesn’t include any “faulty” van der Waals’. Indeed the van der Waals’ corrected functional (PBE+D2) results shows the worst performance on structural properties. For the cold curve the PBE+D2 functional gives the best results compared to experiments (room temperature) but since the structural properties were bad with this functional we cannot for sure say that this is in any way a validation. It is shown that scaling the AM05 results with a common factor reproduces the experimental data. We leave the question on why to a follow up study but speculate that maybe the experiment and our calculations do not represent the same system set-up. From the structural properties we identify a site in the TATB lattice that contains a high concentration of oxygen and hydrogen. The consequences of this finding, if any, are left to a future project. In the second part of the study we perform extensive high-quality DFT-MD (molecular dynamics with DFT forces) calculations to obtain points on the Hugoniot. This part of the study did not get finished within this project and a more extensive summary of this part will be given in a follow up report at a future date. However, we show that obtaining calculated data is essential for equations of state development since the existing experimental Hugoniot data barely deviates from room temperature isotherm data and thus give no information of the high temperature dependency of materials properties. Our conclusion so far in the project is that being able to calculate materials properties is essential for high explosives since experiments are unable to give information in the high temperature part of phase space. While blind use of DFT cannot (yet) give unambiguous answers, we can still explore qualitatively and use such information to guide us in EOS development. However, the main conclusion is that we need better functionals in DFT to easily extract needed properties from calculations.

36 MATERIALS SCIENCE↗

Validation of Two Hydrocodes with a Bi-Metallic Shaped Charge Experiment [Slides]

Staggered grid (SGH) and cell-centered (CCH) Lagrangian Hydro are two approaches to modeling high explosives (HE) experiments. HE experiments involve complex flows. For example, the discontinuity in the tangential velocity across a frictionless contact surface. In this work, the SGH and CCH schemes with a contact surface algorithm are used to simulate a bimetallic shaped charge experiment using FLAG. Experiment will be performed at LANL in the coming year and used to validate the SGH and CCH schemes results.

42 ENGINEERING↗

Raytracing

The raytracing (spectrally specific radiative transfer that does not couple back to the hydrodynamic evolution) code was developed because it helps improve our understanding of the physics of explosive events, validates computational physics codes, and estimates optical signals that are cheaper and safer than experiments involving high explosives. The raytracing code can also produce simulations that are useful to analyze what we can understand with sensors, such as determining what we can discriminate with sensors, like the presence of certain metals or the amount of soot. In addition, simulations can provide extra validations to computational physics to help us better understand discrepancies.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Sensitivity of an integrated experiment to uncertainty in the high explosive equations of state

Traditionally, hydrodynamics simulations are performed with a single equation-of-state (EOS) to describe each material. These EOSs typically have a physics-informed functional form with adjustable parameters that are calibrated in order to replicate small-scale data. However, because the calibration data have uncertainty and there are typically inherent degeneracies in fitting the EOS, there are actually multiple EOSs that might be consistent with calibration data. In this work, we perform uncertainty quantification (UQ) for the reactant and product equations of state for the high explosive PBX 9501 to yield an ensemble of EOSs that match the uncertain small-scale calibration data. We then simulate an experiment of an explosively formed penetrator repeatedly with different EOSs to both validate the UQ analysis and determine the effects of EOS uncertainty on the prediction of quantities of interest in the experiment. In general, we find good agreement between the simulation predictions and the experimental measurements, and we identify an EOS variable that contributes most directly to the spread in the predictions as the EOSs are varied.

36 MATERIALS SCIENCE↗

A study of explosively formed fuse (EFF) opening switch resistance

Many pulsed power experiments need pulse shaping to optimize the power flow from a flux compression generator (FCG) to an experimental load. In a laboratory environment this can be a simple task where the switches are not destroyed. However, in experiments with high explosives, where a large amount of damage occurs, a single use EFF opening switch may be a good choice. In an EFF, explosives are used to thin a current carrying sheet of aluminum as it is forced into a grooved dye. The current is modified by the time dependent changes in resistance as the aluminum is stretched. We will correlate the hydrodynamic effects with resistance. The hydrodynamic profile is determined by Mesa-2D, a well proven hydrodynamics computer code, and MA THEMA TICA is used convert material contours into total resistance using the resistivity as a function of time from various sources. Experimentally, we will determine the actual resistance and compare it with the calculated values. We have used these switches for decades but still do not understand the details of the physics. The resistance change may be due to several processes but in this paper we will concentrate on stretching as the most important contribution. Also, in this paper we will compare the details of the hydrodynamics with the details of experimental and calculated resistance and hopefully generate a predictive model for future designs with other geometries and materials.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Scaled experiments on cavity confined explosions in limestone and poly(methyl methacrylate)

A scaled experiment comprising a laser-driven explosion in a cavity is used to characterize the coupling of mechanical energy into the surrounding solid material. Experiments are performed using poly(methyl methacrylate) and dry Salem limestone as the explosion containment blocks materials, in which are milled scaled spherical cavities of various dimensions. Measurements of the coupled shock, taken with fiber optic probes at the cavity wall, show the critical radius where wall deformation transitions from plastic to elastic deformation. These measurements also provide a diagnostic of the air blast, which is validated against GEODYN simulation code. The measurement of the coupled shock amplitude taken farther from the wall in the linear region indicates increased coupling efficiency in small cavities over the range of scaled cavity radii from 6 to 20 m/kt 1/3 , a phenomenon not previously observed in experiments. A comparison of results taken in this experiment with a parallel experiment using high explosive (HE) as the source shows that coupled shocks generated with HE are characteristically different with much larger amplitude than those produced by a high energy density laser-driven source with the same yield. This experimental technique potentially provides a rapid and cost-effective method to analyze the consequences of a full-scale, low yield, buried explosion.

58 GEOSCIENCES↗

Numerical Simulations of Non-Proliferation Experiments

We have implemented a set of numerical simulations to numerically investigate the outcomes of non-proliferation experiments. The high explosive (HE) in the simulations is in the form of a cylinder. The two-dimensional simulations are carried out in the r-z cylindrical coordinate, and the three-dimensional simulation is in the Cartesian coordinate. From the simulation, the cavity formed after detonation stops its expansion after about 0.15 sec. At the time the cavity stops expanding, the cavity shape seems quite spherical although the initial HE is in the shape of cylinder, but the radius in the vertical direction, which is about 19.7m, is a little less than the one in the horizonal direction, which is about 21.5m. Although there is no layer of air between the HE and tuff in real experiments, in addition to the simulations without air, we add a layer of air in one simulation to assess any possible influence of the air on the shape of the cavity.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗