Search NASA⌕ Search

SEARCH · Search NASA

Results for “junction structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The mean flow structure around and within a turbulent junction or horseshoe vortex. I - The upstream and surrounding three-dimensional boundary layer

An experimental study of the mean flow structure upstream, around, and in a turbulent junction or horseshoe vortex is presented for the case of an incompressible subsonic flow. Mean velocity field and turbulent kinetic energy field measurements (obtained with hot film anemometry) and local wall shear stress measurements are used to monitor the upstream and surrounding three-dimensional turbulent boundary layer-like flow away from separation. Freestream or edge velocity and floor static pressure results are reported.

Menna, J. D.↗
NASA NTRS1982

Process Research on Polycrystalline Silicon Material (PROPSM)

The investigation of the performance limiting mechanisms in large grain (greater than 1-2 mm in diameter) polycrystalline silicon was continued by fabricating a set of minicell wafers on a selection of 10 cm x 10 cm wafers. A minicell wafer consists of an array of small (approximately 0.2 sq cm in area) photodiodes which are isolated from one another by a mesa structure. The junction capacitance of each minicell was used to obtain the dopant concentration, and therefore the resistivity, as a function of position across each wafer. The results indicate that there is no significant variation in resistivity with position for any of the polycrystalline wafers, whether Semix or Wacker. However, the resistivity of Semix brick 71-01E did decrease slightly from bottom to top.

Culik, J. S.↗
NASA NTRS1984

K-Band Latching Switches

Design, development, and tests are described for two single-pole-double-throw latching waveguide ferrite switches: a K-band switch in WR-42 waveguide and a Ka-band switch in WR-28 waveguide. Both switches have structurally simple junctions, mechanically interlocked without the use of bonding materials; they are impervious to the effects of thermal, shock, and vibration stresses. Ferrite material for the Ka-band switch with a proper combination of magnetic and dielectric properties was available and resulted in excellent low loss, wideband performance. The high power handling requirement of the K-band switch limited the choice of ferrite to nickel-zinc compositions with adequate magnetic properties, but with too low relative dielectric constant. The relative dielectric constant determines the junction dimensions for given frequency responses. In this case the too low value unavoidably leads to a larger than optimum junction volume, increasing the insertion loss and restricting the operating bandwidth. Efforts to overcome the materials-related difficulties through the design of a composite junction with increased effective dielectric properties efforts to modify the relative dielectric constant of nickel-zinc ferrite are examined.

Piotrowski, W. S.↗
NASA NTRS1984

Microcrystalline silicon growth for heterojunction solar cells

Microcrystalline Si (m-Si) films with a 1.7eV energy bandgap and crystal size of several hundred A were e-beam evaporated on single crystalline Si (c-Si) to form a heterojunction with the substrate, or a window layer to a single crystalline p-n junction (heteroface structure). The goal was to enhance Voc by such uses of the larger bandgap m-Si, with the intriguing prospect of forming heterostructures with exact lattice match on each layer. The heterojunction structure was affected by interface and shunting problems and the best Voc achieved was only 482mV, well below that of single crystal Si homojunctions. The heteroface structure showed promise for some of the samples with p m-Si/p-n structure (the complementary structure did not show any improvement). Although several runs with different deposition conditions were run, the results were inconsistent. Any Voc enhancement obtained was too small to compensate for the current loss due to the extra absorption and poor carrier transport properties of the m-Si film.

Leung, D. C.↗
NASA NTRS1985

Experimental study of the minority-carrier transport at the polysilicon-monosilicon interface

This paper presents the results of an experimental study designed to explore both qualitatively and quantitatively the mechanism of the improved current gain in bipolar transistors with polysilicon emitter contacts. Polysilicon contacts were deposited and heat treated at different conditions. The electrical properties were measured using p-n junction test structures that are much more sensitive to the contact properties than are bipolar transistors. A simple phenomenological model was used to correlate the structural properties with electrical measurements. Possible transport mechanisms are examined and estimates are made about upper bounds on transport parameters in the principal regions of the devices. The main conclusion of this study is that the minority-carrier transport in the polycrystalline silicon is dominated by a highly disordered layer at the polysilicon-monosilicon interface characterized by very low minority-carrier mobility. The effective recombination velocity at the n(+) polysilicon-n(+) monosilicon interface was found to be a strong function of fabrication conditions. The results indicate that the recombination velocity can be much smaller than 10,000 cm/s.

Neugroschel, A.↗
NASA NTRS1992

Planar doped barrier subharmonic mixers

The Planar Doped Barrier (PDB) diode is a device consisting of a p(+) doping spike between two intrinsic layers and n(+) ohmic contacts. This device has the advantages of controllable barrier height, diode capacitance and forward to reverse current ratio. A symmetrically designed PDB has an anti-symmetric current vs. voltage characteristic and is ideal for use as millimeter wave subharmonic mixers. We have fabricated such devices with barrier heights of 0.3, 0.5 and 0.7 volts from GaAs and InGaAs using a multijunction honeycomb structure with junction diameters between one and ten microns. Initial RF measurements are encouraging. The 0.7 volt barrier height 4 micron GaAs devices were tested as subharmonic mixers at 202 GHz with an IF frequency of 1 GHz and had 18 dB of conversion loss. The estimated mismatch loss was 7 dB and was due to higher diode capacitance. The LO frequency was 100.5 GHz and the pump power was 8 mW.

Lee, T. H.↗
NASA NTRS1988

The mean flow structure around and within a turbulent junction or horseshoe vortex. II - The separated and junction vortex flow

Five-hole probe measurements of the flow through the separation region and in the vortex system of an incompressible subsonic flow around and within a turbulent junction or horseshoe vortex are reported. Mean velocity, static pressure, and total pressure results are presented. The streamwise vorticity field is obtained from the measured velocity field. Flow visualization results for the floor and cylinder surface agree well with the flow field data.

Pierce, F. J.↗
NASA NTRS1994

Radiation effects on p+n InP junctions grown by MOCVD

The superior radiation resistance of InP over other solar cell materials such as Si or GaAs has prompted the development of InP cells for space applications. The early research on radiation effects in InP was performed by Yamaguchi and co-workers who showed that, in diffused p-InP junctions, radiation-induced defects were readily annealed both thermally and by injection, which was accompanied by significant cell recovery. More recent research efforts have been made using p-InP grown by metalorganic chemical vapor deposition (MOCVD). While similar deep level transient spectroscopy (DLTS) results were found for radiation induced defects in these cells and in diffused junctions, significant differences existed in the annealing characteristics. After injection annealing at room temperature, Yamaguchi noticed an almost complete recovery of the photovoltaic parameters, while the MOCVD samples showed only minimal annealing. In searching for an explanation of the different annealing behavior of diffused junctions and those grown by MOCVD, several possibilities have been considered. One possibility is the difference in the emitter structure. The diffused junctions have S-doped graded emitters with widths of approximately 0.3 micrometers, while the MOCVD emitters are often doped with Si and have widths of approximately 300A (0.03 micrometers). The difference in the emitter thickness can have important effects, e.g. a larger fraction of the total photocurrent is generated in the n-type material for thicker emitters. Therefore the properties of the n-InP material may explain the difference in the observed overall annealing behavior of the cells.

Messenger, Scott R.↗
NASA NTRS2003

Switching and Rectification in Carbon-Nanotube Junctions

Multi-terminal carbon-nanotube junctions are under investigation as candidate components of nanoscale electronic devices and circuits. Three-terminal "Y" junctions of carbon nanotubes (see Figure 1) have proven to be especially interesting because (1) it is now possible to synthesize them in high yield in a controlled manner and (2) results of preliminary experimental and theoretical studies suggest that such junctions could exhibit switching and rectification properties. Following the preliminary studies, current-versus-voltage characteristics of a number of different "Y" junctions of single-wall carbon nanotubes connected to metal wires were computed. Both semiconducting and metallic nanotubes of various chiralities were considered. Most of the junctions considered were symmetric. These computations involved modeling of the quantum electrical conductivity of the carbon nanotubes and junctions, taking account of such complicating factors as the topological defects (pentagons, heptagons, and octagons) present in the hexagonal molecular structures at the junctions, and the effects of the nanotube/wire interfaces. A major component of the computational approach was the use of an efficient Green s function embedding scheme. The results of these computations showed that symmetric junctions could be expected to support both rectification and switching. The results also showed that rectification and switching properties of a junction could be expected to depend strongly on its symmetry and, to a lesser degree, on the chirality of the nanotubes. In particular, it was found that a zigzag nanotube branching at a symmetric "Y" junction could exhibit either perfect rectification or partial rectification (asymmetric current-versus-voltage characteristic, as in the example of Figure 2). It was also found that an asymmetric "Y" junction would not exhibit rectification.

Srivastava, Deepak↗
NASA NTRS1982

Molecular structure of r/GCG/d/TATACGC/ - A DNA-RNA hybrid helix joined to double helical DNA

The molecule r(GCG)d(TATACGC) is self-complementary and forms two DNA-RNA hybrid segments surrounding a central region of double helical DNA; its molecular structure has been solved by X-ray analysis. All three parts of the molecule adopt a conformation which is close to that seen in the 11-fold RNA double helix. The conformation of the ribonucleotides is partly determined by water molecules bridging between the ribose O2' hydroxyl group and cytosine O2. The hybrid-DNA duplex junction contains no structural discontinuities. However, the central DNA TATA sequence has some structural irregularities.

Wang, A. H.-J.↗
NASA NTRS1975

High efficiency graded band-gap Al/x/Ga/1-x/As-GaAs p-on-n solar cell

A theoretical analysis of p-on-n (p/n) graded band-gap Al/x/Ga/1-x/As-GaAs solar cells including all practical energy loss mechanisms predicts air mass zero efficiencies of 17.3%. The energy losses include those due to spectral reflection, surface, bulk and junction recombination currents, and series resistance. The device consists of a layer of p-type Al/x/Ga/1-x/As 3.5-micron thick on top of an n-type GaAs substrate. The graded band-gap is achieved by decreasing x from 0.35 at the surface to zero at the junction. The same structure without the graded Al concentration, no longer an optimum device, has an efficiency of 10.4%. The primary function of the graded band-gap material is the reduction of surface and bulk recombination losses in the surface layer by a built-in electric field. A comparison of the p/n structure with an optimized n/p structure indicates that the latter has a slightly higher efficiency (17.7%) for assumed minority carrier diffusion lengths and surface recombination velocity.

Hutchby, J. A.↗
NASA NTRS1978

Defect distribution near the surface of electron-irradiated silicon

The surface-defect distributions of electron-irradiated n-type silicon have been investigated using a transient capacitance technique. Schottky, p-n junction, and MOS structures were used in profiling the defect distributions. Surface depletions of defects observed were attributed to the vacancy distribution, but not that of oxygen, and other capture centers' distributions. The vacancy diffusion length at 300 K was estimated to be about 3-6 microns.

Wang, K. L.↗
NASA NTRS1980

Results of the Air Force high efficiency cascaded multiple bandgap solar cell programs

The III-V semiconductor materials system that was selected for continued cascade cell development was the AlGaAs cell on GaAs cell structure. The tunnel junction used as transparent ohmic contact between the top cell and the bottom cell continued to be the central difficulty in achieving the program objective of 25 percent AMO efficiency at 25 C. During the tunnel junction and top cell developments it became apparent that the AlGaAs cell has potential for independent development as a single junction converter and is a logical extension of the present GaAs heteroface technology.

Rahilly, W. P.↗
NASA NTRS1987

The case for aerodynamic sensitivity analysis

No specific solutions are offered, nor verified by applications, for its subject problem which is sensitivity analysis in Computational Fluid Dynamics (CFD). Instead, a plea is made to the CFD community for extending their present capability to include sensitivity analysis. The plea is made from the viewpoint of an aeronautical engineer, not an expert in CFD methods, who needs the sensitivity information when working at the junction of aerodynamics, structures, active controls, and other disciplines whose inputs need to be integrated in aircraft design.

Sobieszczanski-Sobieski, Jaroslaw↗
NASA NTRS1992

Double-Current-Confined CSP Laser

Improved channeled-substrate-planar (CSP) lasers that emit at wavelengths between 860 and 880 nm grown by liquid-phase epitaxy (LPE). Exhibit record high output powers and efficiencies, attained without sacrifice of desirable characteristics of lasers. In fabrication, second reverse-bias p/n junction incorporated to reduce required current. By incorporating two reverse-bias junctions in CSP structure, one doubly confines current. Lasers used eventually as sources of light in intersatellite communications systems and, specifically, NASA Advanced Communications Technology Satellite (ACTS) System.

Connolly, John C.↗