Results for “plug” — Page 2

NASA NTRS2017

Coil-On-Plug Ignition for LOX/Methane Liquid Rocket Engines in Thermal Vacuum Environments

A coil-on-plug ignition system has been developed and tested for Liquid Oxygen (LOX) / liquid methane rocket engines operating in thermal vacuum conditions. The igniters were developed and tested as part of the Integrated Cryogenic Propulsion Test Article (ICPTA), previously tested as part of the Project Morpheus test vehicle. The ICPTA uses an integrated, pressure-fed, cryogenic LOX/methane propulsion system including a reaction control system (RCS) and a main engine. The ICPTA was tested at NASA Glenn Research Center's Plum Brook Station in the Spacecraft Propulsion Research Facility (B-2) under vacuum and thermal vacuum conditions. In order to successfully demonstrate ignition reliability in the vacuum conditions and eliminate corona discharge issues, a coil-on-plug ignition system has been developed. The ICPTA uses spark-plug ignition for both the main engine igniter and the RCS. The coil-on-plug configuration eliminates the conventional high-voltage spark plug cable by combining the coil and the spark-plug into a single component. Prior to ICPTA testing at Plum Brook, component-level reaction control engine (RCE) and main engine igniter testing was conducted at NASA Johnson Space Center (JSC), which demonstrated successful hot-fire ignition using the coil-on-plug from sea-level ambient conditions down to 10(exp.-2) torr. Integrated vehicle hot-fire testing at JSC demonstrated electrical and command/data system performance. Lastly, Plum Brook testing demonstrated successful ignitions at simulated altitude conditions at 30 torr and cold thermal-vacuum conditions at 6 torr. The test campaign successfully proved that coil-on-plug technology will enable integrated LOX/methane propulsion systems in future spacecraft.

Melcher, John C.↗

NASA NTRS2017

Coil-On-Plug Ignition for Oxygen/Methane Liquid Rocket Engines in Thermal-Vacuum Environments

A coil-on-plug ignition system has been developed and tested for Liquid Oxygen (LOX)/liquid methane (LCH4) rocket engines operating in thermal vacuum conditions. The igniters were developed and tested as part of the Integrated Cryogenic Propulsion Test Article (ICPTA), previously tested as part of the Project Morpheus test vehicle. The ICPTA uses an integrated, pressure-fed, cryogenic LOX/LCH4 propulsion system including a reaction control system (RCS) and a main engine. The ICPTA was tested at NASA Glenn Research Center's Plum Brook Station in the Spacecraft Propulsion Research Facility (B-2) under vacuum and thermal vacuum conditions. A coil-on-plug ignition system has been developed to successfully demonstrate ignition reliability at these conditions while preventing corona discharge issues. The ICPTA uses spark plug ignition for both the main engine igniter and the RCS. The coil-on-plug configuration eliminates the conventional high-voltage spark plug cable by combining the coil and the spark plug into a single component. Prior to ICPTA testing at Plum Brook, component-level reaction control engine (RCE) and main engine igniter testing was conducted at NASA Johnson Space Center (JSC), which demonstrated successful hot-fire ignition using the coil-on-plug from sea-level ambient conditions down to 10(exp -2) torr. Integrated vehicle hot-fire testing at JSC demonstrated electrical and command/data system performance. Lastly, hot-fire testing at Plum Brook demonstrated successful ignitions at simulated altitude conditions at 30 torr and cold thermal-vacuum conditions at 6 torr. The test campaign successfully proved that coil-on-plug technology will enable integrated LOX/LCH4 propulsion systems in future spacecraft.

Melcher, John C.↗

NASA NTRS2024

Flow, Noise and Thrust of Supersonic Plug Nozzles

A model-scale experimental study is conducted with a plug nozzle exploring the performance of various plug geometries for supersonic aircraft concepts. All data are acquired with a given outer nozzle that is convergent and has an exit diameter of 2 inches. The shape of the centrally placed plug is varied from conic with various half-angles (lengths), to method of characteristics (MoC) designs, as well as truncated and porous geometries. Noise and schlieren flow visualization data, presented in an earlier paper, are briefly reviewed first. The focus in this paper is on the thrust performance. A newly constructed thrust stand is used to acquire data covering a nozzle pressure ratio (NPR) range from transonic (‘landing and takeoff’, LTO) to supersonic (‘cruise’) conditions. Back-to-back measurements allowed assessment of relative performance. A plug with its ‘crown’ located somewhat inside the nozzle, rather than near the exit, is found to perform better. A longer 10° plug performs better than a shorter 22° plug. A porous plug, that significantly suppresses broadband shock associated noise, is found to incur a modest thrust loss that might be an acceptable tradeoff near LTO conditions. A companion numerical simulation for some of the plug geometries yields data trends bearing reasonable agreement with the experimental results.

jets↗

NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

Nozzles with external plugs are candidates for the exhaust system of supersonic aircraft concepts in an ongoing research effort at NASA. As part of that effort a fundamental study is being conducted at NASA Glenn Research Center (GRC). Experimental and limited numerical simulation results from this study, for a plug nozzle with a convergent nozzle (cowl),have been reported in recent publications[1,2]. Conventional method-of-characteristics (MoC) design for the plug requires that the flow is choked at the nozzle exit. This is why a sharp convergence of the cowl is invoked in such a design in most previous studies [3-5], leading to the earlier choice of the convergent cowl. Such a nozzle, however, is not suitable for supersonic flights because of large boat tail drag suffered by its outer surface. The boat tail drag consideration dictates that the cowl be more or less cylindrical in shape. While various other shapes have been studied in the past [6], essentially a cylindrical shape is adopted in the larger research program at NASA. The cylindrical shape has certain advantages. With the plug crown located somewhat inside the nozzle, the flow experiences convergence and divergence as with a C-D nozzle. By translating the plug, different throat-to-exit area ratio could be achieved to obtain fully expanded condition at different values of NPR. This offers a relatively easy active control strategy for the nozzle geometry throughout the flight regime from landing and takeoff (LTO) to cruise conditions. A plug nozzle model mimicking the geometry being considered in the NASA program, i.e., having a cylindrical exit, have been fabricated recently for continued fundamental studies. Some of the plugs used with the earlier convergent cowl [1] are readily adopted to this model. In addition, a few other plugs have been obtained following a numerical optimization study [7]. The various configurations are to be investigated for thrust, noise and flow fields, with complementing numerical simulations. Thrust data for a variety of configurations as well as limited noise data are in hand. Further explorations including schlieren visualization are to be conducted in the near future. The proposed paper is to summarize all these results. In the following, a few key results obtained so far are described.

jets↗

NASA NTRSDate not supplied

Noise of Internally Mixed Exhaust Systems With External Plug For Supersonic Transport Applications

Internally mixed exhaust systems produce more noise than would be expected from an equivalent fully mixed flow. This ‘excess noise’ has never been fully explained and has not been researched recently as it is not as much of a problem for high bypass-ratio exhaust systems. Commercial supersonic vehicles, however, will use more moderate bypass ratio engines. Their exhaust systems will also likely feature external plugs to improve boat tail angle for cruise performance. Thus the problem of excess noise will need to be addressed along with the impacts of having an external plug. Recently, acoustic tests of dual-stream jet flows from both internal and external plug nozzles have been conducted. Measurements of noise from flows with an axisymmetric splitter and lobed forced mixer were made. These measurements show the baseline ‘excess noise’ previously found in forced mixer exhaust systems, and show how this noise source differs depending upon the plug geometry. Background-oriented schlieren measurements acquired simultaneously document the differences in shock structures over the transonic flow regime tested. The far-field acoustic measurements indicate that an external plug can slightly reduce the mixing noise of the jet plume when the flow is completely mixed, e.g. when the core and bypass streams have the same temperature and the flow is a single-stream jet. However, when the flow is not fully mixed, e.g. the usual case of an internally mixed exhaust system, the plug seems to amplify the ‘excess noise’ associated with the mixer. This additional noise source presents a challenge for nozzle designers wanting to use internally mixed exhaust systems with external plug nozzles.

Jet noise↗

NASA NTRSDate not supplied

Investigation of Physical Mechanisms for Jet Noise Reduction by Plug Nozzle Porosity

This paper presents the results of a computational study on porous-plug nozzles for their eventual application in reducing takeoff noise levels for supersonic civil transport. The study explores a wide range of porous-plug geometries, encompassing variations in hole size, plug length and porosity. Computational fluid dynamics (CFD) analyses are employed in concert with an advanced automated mesh refinement (AMR) scheme, Sketch-to-Solution (S2S), to investigate porous plug nozzle design strategies that may diminish shock strength, broad-band shock noise (BBSN), flow separation, and other undesirable characteristics associated with high takeoff noise levels. A selected subset of the porous-plug nozzles that were analyzed computationally were manufactured at subscale using stereolithography 3D printing. These nozzles were tested experimentally, obtaining far-field noise spectral data and schlieren flow visualization pictures. Detailed comparisons between CFD predictions and experimental results were conducted. These comparisons focus on gaining a better understanding of the underlying physical mechanisms responsible for noise reduction with the porous plugs relative to corresponding solid plugs.

computational fluid dynamics↗

NASA NTRSDate not supplied

Investigation of Physical Mechanisms for Jet Noise Reduction by Plug Nozzle Porosity

This paper presents the results of a computational study on porous-plug nozzles for their eventual application in reducing takeoff noise levels for supersonic civil transport. The study explores a wide range of porous-plug geometries, encompassing variations in hole size, plug length and porosity. Computational fluid dynamics (CFD) analyses are employed in concert with an advanced automated mesh refinement (AMR) scheme, Sketch-to-Solution (S2S), to investigate porous plug nozzle design strategies that may diminish shock strength, broad-band shock noise (BBSN), flow separation, and other undesirable characteristics associated with high takeoff noise levels. A selected subset of the porous-plug nozzles that were analyzed computationally were manufactured at subscale using stereolithography 3D printing. These nozzles were tested experimentally, obtaining far-field noise spectral data and schlieren flow visualization pictures. Detailed comparisons between CFD predictions and experimental results were conducted. These comparisons focus on gaining a better understanding of the underlying physical mechanisms responsible for noise reduction with the porous plugs relative to corresponding solid plugs.

Nozzles↗

NASA NTRS1981

Acoustic and aerodynamic performance investigation of inverted velocity profile coannular plug nozzles

The results of model scale parametric static and wind tunnel aerodynamic performance tests on unsuppressed coannular plug nozzle configurations with inverted velocity profile are discussed. The nozzle configurations are high-radius-ratio coannular plug nozzles applicable to dual-stream exhaust systems typical of a variable cycle engine for Advanced Supersonic Transport application. In all, seven acoustic models and eight aerodynamic performance models were tested. The nozzle geometric variables included outer stream radius ratio, inner stream to outer stream ratio, and inner stream plug shape. When compared to a conical nozzle at the same specific thrust, the results of the static acoustic tests with the coannular nozzles showed noise reductions of up to 7 PNdB. Extensive data analysis showed that the overall acoustic results can be well correlated using the mixed stream velocity and the mixed stream density. Results also showed that suppression levels are geometry and flow regulation dependent with the outer stream radius ratio, inner stream-to-outer stream velocity ratio and inner stream velocity ratio and inner stream plug shape, as the primary suppression parameters. In addition, high-radius ratio coannular plug nozzles were found to yield shock associated noise level reductions relative to a conical nozzle. The wind tunnel aerodynamic tests showed that static and simulated flight thrust coefficient at typical takeoff conditions are quite good - up to 0.98 at static conditions and 0.974 at a takeoff Mach number of 0.36. At low inner stream flow conditions significant thrust loss was observed. Using an inner stream conical plug resulted in 1% to 2% higher performance levels than nozzle geometries using a bent inner plug.

Knott, P. R.↗

NASA NTRS1982

Pulsed plasma thruster ignitor plug ignition characteristics

The operating characteristics of the semiconductor spark gap ignitor plug used to initiate the discharge in a pulsed plasma thruster are investigated. Current and voltage waveform measurements for the ignitor plug alone, and for the plug mounted in the thruster cathode indicate an average dynamic impedance of 0.2 ohms for a wide range of operating conditions, and a trigger circuit energy transfer efficiency to the plug on the order of 25%. Two modes of trigger ignition are found which are related to the rise time of the applied voltage pulse. Analysis of plasma characteristics reveals plug erosion to occur primarily in the semiconductor and anode regions, by mechanisms including plug metal embrittlement, plasma sputtering and vaporization caused by the discharge current pulse. Measurements also indicate a plume velocity on the order of 1580,000 cm/sec which increases with trigger circuit stored energy. The results establish levels of performance for future applications of semiconductor spark gap ignitor plugs in plasma devices.

Brady, M. E.↗

NASA NTRS1983

Aeroacoustics of supersonic porous plug-nozzle flows

The effects of porosity on attenuation of noise from short plug-nozzle flows have been studied. Porosity of 10 percent distributed over the whole surface and porosity of 4 percent distributed over the middle-third surface of the conical plug have been investigated. The porosity results in favorable modifications of the repetitive shock structures as revealed by the shadowgraphs of the flow. The acoustic data indicate a reduction of noise intensity levels up to 4 dB for the porous plugs as compared to the solid concial plug. The locally distributed holes (4 percent porosity) are found to give aeroacoustic performance comparable to those with holes distributed over the whole surface (10 percent porosity). Also, the solid conical plug-nozzle is noted to yield noise reductions up to 9 dB when compared to the conical convergent plug-nozzle. A proposed mechanism of shock modification in porous plug-nozzle. A supported by shadowgraphic records.

Dosanjh, D. S.↗

NASA NTRS2012

Friction Pull Plug Welding in Aluminum Alloys

NASA's Marshall Space Flight Center (MSFC) has recently invested much time and effort into the process development of Friction Pull Plug Welding (FPPW). FPPW, is a welding process similar to Friction Push Plug Welding in that, there is a small rotating part (plug) being spun and simultaneously pulled (forged) into a larger part. These two processes differ, in that push plug welding requires an internal reaction support, while pull plug welding reacts to the load externally. FPPW was originally conceived as a post proof repair technique for the Space Shuttle fs External Tank. FPPW was easily selected as the primary weld process used to close out the termination hole on the Constellation Program's ARES I Upper Stage circumferential Self-Reacting Friction Stir Welds (SR-FSW). The versatility of FPPW allows it to also be used as a repair technique for both SR-FSW and Conventional Friction Stir Welds. To date, all MSFC led development has been concentrated on aluminum alloys (2195, 2219, and 2014). Much work has been done to fully understand and characterize the process's limitations. A heavy emphasis has been spent on plug design, to match the various weldland thicknesses and alloy combinations. This presentation will summarize these development efforts including weld parameter development, process control, parameter sensitivity studies, plug repair techniques, material properties including tensile, fracture and failure analysis.

Brooke, Shane A.↗

NASA NTRS2011

Friction Pull Plug Welding in Aluminum Alloys

NASA fs Marshall Space Flight Center (MSFC) has recently invested much time and effort into the process development of Friction Pull Plug Welding (FPPW). FPPW, is a welding process similar to Friction Push Plug Welding in that, there is a small rotating part (plug) being spun and simultaneously pulled (forged) into a larger part. These two processes differ, in that push plug welding requires an internal reaction support, while pull plug welding reacts to the load externally. FPPW was originally conceived as a post proof repair technique for External Tank. FPPW was easily selected as the primary process used to close out the termination hole on the Constellation Program fs ARES I Upper Stage circumferential Self ] Reacting Friction Stir Welds (SR ]FSW). The versatility of FPPW allows it to also be used as a repair technique for both SR ]FSW and Conventional Friction Stir Welds. To date, all MSFC led development has been concentrated on aluminum alloys (2195, 2219, and 2014). Much work has been done to fully understand and characterize the process fs limitations. A heavy emphasis has been spent on plug design, to match the various weldland thicknesses and alloy combinations. This presentation will summarize these development efforts including weld parameter development, process control, parameter sensitivity studies, plug repair techniques, material properties including tensile, fracture and failure analysis.

Brooke, Shane A.↗

NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗

NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗

NASA NTRSDate not supplied

Optimization of Plug Nozzles Using CFD Informed Design Space Querying

This paper presents an axisymmetric CFD approach based on Reynolds-averaged Navier-Stokes (RANS) calculations for the shape optimization of plug nozzle contours for both supersonic cruise and landing/takeoff (LTO) conditions. Three key external plug design parameters were defined as independent variables in the optimization scheme, while nozzle performance was evaluated using thrust coefficient (Cfg) and discharge coefficient (Cd) as the primary dependent variables. By varying these parameters, a wide range of axisymmetric conic section plug profiles can be achieved, simplifying the problem. The paper also discusses the supersonic plug nozzle optimization approach, design space seeding, meshing, and CFD simulations for the optimization process. The results demonstrate that the approach is effective in exploring the parameter space and reducing computational expenses, making it a viable option for optimizing nozzle plug contours. Using this optimization toolchain, the study yielded preliminary designs for LTO, cruise, and LTO-cruise balanced plug nozzles.

nozzles↗

NASA NTRSDate not supplied

Optimization of Plug Nozzles Using CFD Informed Design Space Querying

This paper presents an axisymmetric CFD approach based on Reynolds-averaged Navier-Stokes (RANS) calculations for the shape optimization of plug nozzle contours for both supersonic cruise and landing/takeoff (LTO) conditions. Three key external plug design parameters were defined as independent variables in the optimization scheme, while nozzle performance was evaluated using thrust coefficient (Cfg) and discharge coefficient (Cd) as the primary dependent variables. By varying these parameters, a wide range of axisymmetric conic section plug profiles can be achieved, simplifying the problem. The paper also discusses the supersonic plug nozzle optimization approach, design space seeding, meshing, and CFD simulations for the optimization process. The results demonstrate that the approach is effective in exploring the parameter space and reducing computational expenses, making it a viable option for optimizing nozzle plug contours. Using this optimization toolchain, the study yielded preliminary designs for LTO, cruise, and LTO-cruise balanced plug nozzles.

CFD↗

NASA NTRS1983

Burner rig study of variables involved in hole plugging of air cooled turbine engine vanes

The effects of combustion gas composition, flame temperatures, and cooling air mass flow on the plugging of film cooling holes by a Ca-Fe-P-containing deposit were investigated. The testing was performed on film-cooled vanes exposed to the combustion gases of an atmospheric Mach 0.3 burner rig. The extent of plugging was determined by measurement of the open hole area at the conclusion of the tests as well as continuous monitoring of some of the tests using stop-action photography. In general, as the P content increased, plugging rates also increased. The plugging was reduced by increasing flame temperature and cooling air mass flow rates. At times up to approximately 2 hours little plugging was observed. This apparent incubation period was followed by rapid plugging, reaching in several hours a maximum closure whose value depended on the conditions of the test.

Deadmore, D. L.↗

NASA NTRS1990

The liquid/vapor boundary in a porous plug

Results are presented from measurements of pressure and temperature differences as a function of the flow rate and hydrostatic head for two types of porous plugs for phase separation of superfluid He and He vapor: (1) a plug made of sintered stainless steel, similar to that in the IRAS, IRT, and COBE dewars except for larger pores, and (2) a glass plug with pores of uniform cross section. Results show that a liquid/vapor phase boundary exists at the outer surface of the porous plug for low flows or large hydrostatic heads; as the flow increases or the hydrostatic head decreases, the boundary retreats into the plug. Some hysteresis near the phase boundary retreat was observed in the stainless steel plug.

Dipirro, M. J.↗