Search NASA⌕ Search

SEARCH · Search NASA

Results for “processing parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Varying Processing Parameters in the Development of Slurry-Based Oxide Bond Coat for Environmental Barrier Coatings

Silicon carbide (SiC)-based ceramic matrix composites (CMCs) are replacing nickel-base superalloys in some hot-section aircraft engine materials due to their lower density and higher working temperature. CMCs require an environmental barrier coating (EBC) for protection from corrosive combustion species. Current-generation EBCs consist of a rare earth silicate topcoat and a silicon bond coat; however, the relatively low melting point of silicon (1414°C) limits the upper use temperature of these coatings. To extend the capability of next-generation EBCs, an oxide-based bond coat capable of withstanding temperatures of up to 1480°C has been developed at NASA Glenn Research Center. In this study, the oxide-based bond coat was applied to monolithic SiC via a slurry coating process. Parameters including slurry particle size and viscosity were varied, and coating performance was evaluated after steam cycling at 1480°C. The effect of including different rare earth constituents in the bond coat was also explored.

R. I. Webster↗
NASA NTRS1989

Spray automated balancing of rotors - How process parameters influence performance

This paper addresses the application of spray-automated balancing of rotors, and the influence that various operating parameters will have on balancing performance. Spray-automated balancing uses the fuel-air repetitive explosion process to imbed short, discrete bursts of high velocity, high temperature powder into a rotating part at an angle selected to reduce unbalance of the part. The shortness of the burst, the delay in firing of the gun, the speed of the disk and the variability in speed all influence the accuracy and effectiveness of the automated balancing process. The paper evaluates this influence by developing an analytical framework and supplementing the analysis with empirical data obtained while firing the gun at a rotating disk. Encouraging results are obtained, and it is shown that the process should perform satisfactorily over a wide range of operating parameters. Further experimental results demonstrate the ability of the method to reduce vibration levels induced by mass unbalance in a rotating disk.

Smalley, A. J.↗
NASA NTRS1996

Optimization of Residual Stresses in MMC's through Process Parameter Control and the use of Heterogeneous Compensating/Compliant Interfacial Layers. OPTCOMP2 User's Guide

A user's guide for the computer program OPTCOMP2 is presented in this report. This program provides a capability to optimize the fabrication or service-induced residual stresses in unidirectional metal matrix composites subjected to combined thermomechanical axisymmetric loading by altering the processing history, as well as through the microstructural design of interfacial fiber coatings. The user specifies the initial architecture of the composite and the load history, with the constituent materials being elastic, plastic, viscoplastic, or as defined by the 'user-defined' constitutive model, in addition to the objective function and constraints, through a user-friendly data input interface. The optimization procedure is based on an efficient solution methodology for the inelastic response of a fiber/interface layer(s)/matrix concentric cylinder model where the interface layers can be either homogeneous or heterogeneous. The response of heterogeneous layers is modeled using Aboudi's three-dimensional method of cells micromechanics model. The commercial optimization package DOT is used for the nonlinear optimization problem. The solution methodology for the arbitrarily layered cylinder is based on the local-global stiffness matrix formulation and Mendelson's iterative technique of successive elastic solutions developed for elastoplastic boundary-value problems. The optimization algorithm employed in DOT is based on the method of feasible directions.

Pindera, Marek-Jerzy↗
NASA NTRS1992

The influence of processing parameters on microstructural development of low-weight-percent primary, pro-eutectic, dendritic alloys during directional solidification

Alloy compositions centering about Sn- 5 to 15 wt pct Al and Pb- 4 to 20 wt pct Cu have been directionally solidified as a function of growth rate and orientation with respect to earth's gravity vector. The effect of these processing variables on macrosegregation is presented, and the consequence of a structural transition from primary columnar to equiaxed dendritic growth is examined. Effects detrimental to microstructure and attributed to density variations are shown to be minimized by a novel processing technique. In view of the ground-based results, some considerations follow regarding what might be gained by solidifying these alloys in a microgravity environment.

Grugel, R. N.↗
NASA NTRS1993

Optimization of the Processing Parameters of High Temperature Superconducting Glass-Ceramics: Center Director's Discretionary Fund Final Report

A number of promising glass forming compositions of high Tc superconducting Ba-Sr-Ca-Cu-O (BSCCO) materials were evaluated for their glass-ceramic crystallization ability. The BSCCO ceramics belonging to the class of superconductors in the Ba-Sr-Ca-Cu-O system were the focus of this study. By first forming the superconducting material as a glass, subsequent devitrification into the crystalline (glass-ceramic) superconductor can be performed by thermal processing of the glass preform body. Glass formability and phase formation were determined by a variety of methods in another related study. This study focused on the nucleation and crystallization of the materials. Thermal analysis during rapid cooling aids in the evaluation of nucleation and crystallization behavior. Melt viscosity is used to predict glass formation ability.

Ethridge, E. C.↗
NASA NTRS1988

Effect of processing parameters on the characteristics of high-Tc superconductor YBa2Cu3Oy

SEM, thermogravimetric analysis, powder X-ray diffraction,and measurements of electrical resistivity and magnetic susceptibility, are presently used to characterize the influence of sintering temperature, sintering and annealing atmospheres, and quench-rate on the properties of the YBa2Cu3Oy superconducting oxide. It is established that annealing in oxygen, together with slow cooling rates, are required for preparation of high-Tc superconductors with sharp transitions; rapid quenching from high temperature does not yield good superconductors, due to low oxygen content.

Bansal, Narottam P.↗
NASA NTRS1999

Dimensionless Numbers Expressed in Terms of Common CVD Process Parameters

A variety of dimensionless numbers related to momentum and heat transfer are useful in Chemical Vapor Deposition (CVD) analysis. These numbers are not traditionally calculated by directly using reactor operating parameters, such as temperature and pressure. In this paper, these numbers have been expressed in a form that explicitly shows their dependence upon the carrier gas, reactor geometry, and reactor operation conditions. These expressions were derived for both monatomic and diatomic gases using estimation techniques for viscosity, thermal conductivity, and heat capacity. Values calculated from these expressions compared well to previously published values. These expressions provide a relatively quick method for predicting changes in the flow patterns resulting from changes in the reactor operating conditions.

Kuczmarski, Maria A.↗
NASA NTRS1978

FETSIM user's manual and example

A batch program written in FORTRAN IV which does D.C. and transient analysis of MOS circuits is presented. Circuits employing N-MOS transistors and/or P-MOS transistors in either a bulk technology or an SOS technology, or almost any combination of R-C elements may be analyzed. The program requires as input data the complete circuit topology, device parameters, process parameters, and control parameters. The user can specify initial node conditions and the input pulse format. For example, pulse rise time, fall time, width and time between succeeding pulses are all independently controllable. The program contains a sophisticated mathematical model that can accurately handle either NMOS, P-MOS, Bulk or SOS devices. Sensitivity to process changes is maintained by requiring such process parameters as threshold voltage and doping level as program inputs.

Source record↗
NASA NTRS1991

RTM: Cost-effective processing of composite structures

Resin transfer molding (RTM) is a promising method for cost effective fabrication of high strength, low weight composite structures from textile preforms. In this process, dry fibers are placed in a mold, resin is introduced either by vacuum infusion or pressure, and the part is cured. RTM has been used in many industries, including automotive, recreation, and aerospace. Each of the industries has different requirements of material strength, weight, reliability, environmental resistance, cost, and production rate. These requirements drive the selection of fibers and resins, fiber volume fractions, fiber orientations, mold design, and processing equipment. Research is made into applying RTM to primary aircraft structures which require high strength and stiffness at low density. The material requirements are discussed of various industries, along with methods of orienting and distributing fibers, mold configurations, and processing parameters. Processing and material parameters such as resin viscosity, perform compaction and permeability, and tool design concepts are discussed. Experimental methods to measure preform compaction and permeability are presented.

Hasko, Greg↗