Search NASA⌕ Search

SEARCH · Search NASA

Results for “reference solar cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Voltage-current-power meter for photovoltaic solar arrays

A meter is disclosed for measuring the voltage, current, and power (VIP) parameters of a photovoltaic solar array, or array module, under sunlight operating conditions utilizing a variable load connected across the array and controlled by a voltage regulator which responds to the difference between the output voltage of the array and a programmed test voltage from a source which generates a single ramp voltage for measuring and recording current as a function of voltage, repeated ramp voltages at a high rate for peak output measurements or a DC voltage for VIP measurements at selected points on the I-V characteristic curve of the array. The voltage signal from a current sensing element, such as a shunt resistor in series with the variable load, is compared with the output current of a reference solar cell to provide a normalizing signal to be added to the signal from the current-sensing element in order to provide a record of array current as a function of array voltage, i.e., for all load conditions from short circuit to open circuit. As the normalized current is thus measured, an analog multiplier multiplies the array voltage and normalized current to provide a measurement of power. Switches are provided to selectively connect the power, P, current, I, or voltage, V, to a meter, directly or through a peak detector. At the same time any one of the parameters V, I and P may be recorded as a function of any other parameter.

Ross, Ronald G.↗
NASA NTRS1985

Air mass 1.5 global and direct solar simulation and secondary reference cell calibration using a filtered large area pulsed solar simulator

Spectral mismatch between a solar simulator and a desired spectrum can result in nearly 20 percent measurement error in the output of photovoltaic devices. This occurs when a crystalline silicon cell monitors the intensity of an unfiltered large area pulsed solar simulator (LAPSS) simulating the ASTM air mass 1.5 direct spectrum and the test device is amorphous silicon. The LAPSS spectral irradiance is modified with readily available glass UV filters to closely match either the ASTM air mass 1.5 direct or global spectrum. Measurement error is reduced to about 1 percent when using either filter if the reference cell and test device are the same general type.

Mueller, Robert L.↗
DOE OSTI2020

Impact of dopant-induced optoelectronic tails on open-circuit voltage in arsenic-doped Cd(Se)Te solar cells

Fluctuations refer to inhomogeneity in the distribution of donors and acceptors at the nanometer scale and occur in many compound solar cell materials such as Cu(In,Ga)Se 2 , Cu 2 ZnSn(S,Se) 4 , and CdSe x Te 1-x . In this work, numerical simulations show that these fluctuations produce not only electrostatic potential variation, but also, local changes in the carrier density and effective bandgap. For a CdSe x Te 1-x absorber doped with arsenic, simulations and cathodoluminescence data within single grains demonstrate how donor and acceptor densities—consistent with capacitance-voltage and secondary-ion mass-spectrometry data—produce tails in photoluminescence, quantum efficiency, and absorption measurements. Using multiple theoretical approaches, we demonstrate that the fluctuations can hinder expected performance gains from increased carrier density, and we describe the significant open-circuit voltage deficit observed in the CdSe x Te 1-x :As solar technology. Our results demonstrate that it is critical to characterize and reduce carrier compensation to realize a higher efficiency.

14 SOLAR ENERGY↗
NASA NTRS1978

High efficiency low cost solar cell power

A concept for generating high-efficiency, low-cost, solar-cell power is outlined with reference to solar cell parameters, optical concentrators, and thermal control procedures. A design for a 12.5-kw power module for space operation is discussed noting the optical system, spectrum splitter, light conversion system, cell cooling, power conditioner, and tracking mechanism. It is found that for an unconcentrated array, efficiency approaches 60% when ten or more bandgaps are used. For a 12-band system, a computer program distributed bandgaps for maximum efficiency and equal cell currents. Rigid materials and thin films have been proposed for optical components and prisms, gratings, and dichroic mirrors have been recommended for spectrum splitting. Various radiator concepts are noted including that of Weatherston and Smith (1960) and Hedgepeth and Knapp (1978). The concept may be suitable for the Solar Power Satellite.

Bekey, I.↗
NASA NTRS1995

Results of the 1995 JPL balloon flight solar cell calibration program

The Jet Propulsion Laboratory (JPL) solar cell calibration program was conceived to produce reference standards for the purpose of accurately setting solar simulator intensities. The concept was to fly solar cells on a high-altitude balloon, to measure their output at altitudes near 120,000 ft (36.6 km), to recover the cells, and to use them as reference standards. The procedure is simple. The reference cell is placed in the simulator beam, and the beam intensity is adjusted until the reference cell reads the same as it read on the balloon. As long as the reference cell has the same spectral response as the cells or panels to be measured, this is a very accurate method of setting the intensity. But as solar cell technology changes, the spectral response of the solar cells changes also, and reference standards using the new technology must be built and calibrated. Until the summer of 1985, there had always been a question as to how much the atmosphere above the balloon modified the solar spectrum. If the modification was significant, the reference cells might not have the required accuracy. Solar cells made in recent years have increasingly higher blue responses, and if the atmosphere has any effect at all, it would be expected to modify the calibration of these newer blue cells much more so than for cells made in the past. JPL has been flying calibration standards on high-altitude balloons since 1963 and continues to organize a calibration balloon flight at least once a year. The 1995 flight was the 48th flight in this series. The 1995 flight incorporated 46 solar cell modules from 7 different participants. The payload included Si, amorphous Si, GaAs, GaAs/Ge, dual junction cells, top and bottom sections of dual junction cells, and a triple junction cell. A new data acquisition system was built for the balloon flights and flown for the first time on the 1995 flight. This system allows the measurement of current-voltage (I-V) curves for 20 modules in addition to measurement of modules with fixed loads as had been done in the past.

Anspaugh, B. E.↗
NASA NTRS1977

Optimum antireflection coating for Antireflection-coated Metal-Oxide-Semiconductor /AMOS/ solar cells

Consideration is given to the design of a single-layer optimum antireflection coating for AMOS (antireflection-coated metal-oxide-semiconductor) solar cells to match the entire sunlight spectrum. The energy conversion efficiency is maximized by maximizing the open-circuit voltage and the short-circuit current. The former is maximized by oxidation techniques and the latter is maximized by the light-coupling into the solar cell. With reference to the effective index of refraction as obtained by ellipsometry, examples of optimum antireflection coatings for 60-A Au-GaAs solar cells are presented.

Yeh, Y. C. M.↗
NASA NTRS1985

Silicon MINP solar cells

The MINP solar cell concept refers to a cell structure designed to be a base region dominated device. Thus, it is desirable that recombination losses are reduced to the point that they occur only in the base region. The most unique feature of the MINP cell design is that a tunneling contact is utilized for the metallic contact on the front surface. The areas under the collector grid and bus bar are passivated by a thin oxide of tunneling thickness. Efforts must also be taken to minimize recombination at the surface between grid lines, at the junction periphery and within the emitter. Results of both theoretical and experimental studies of silicon MINP cells are given. Performance calculations are described which give expected efficiencies as a function of base resistivity and junction depth. Fabrication and characterization of cells are discussed which are based on 0.2 ohm-cm substrates, diffused emitters on the order of 0.15 to 0.20 microns deep, and with Mg MIS collector grids. A total area AM 1 efficiency of 16.8% was achieved. Detailed analyses of photocurrent and current loss mechanisms are presented and utilized to discuss future directions of research. Finally, results reported by other workers are discussed.

Olsen, L. C.↗
NASA NTRS1986

Flat-plate solar array project. Volume 3: Silicon sheet: Wafers and ribbons

The primary objective of the Silicon Sheet Task of the Flat-Plate Solar Array (FSA) Project was the development of one or more low cost technologies for producing silicon sheet suitable for processing into cost-competitive solar cells. Silicon sheet refers to high purity crystalline silicon of size and thickness for fabrication into solar cells. Areas covered in the project were ingot growth and casting, wafering, ribbon growth, and other sheet technologies. The task made and fostered significant improvements in silicon sheet including processing of both ingot and ribbon technologies. An additional important outcome was the vastly improved understanding of the characteristics associated with high quality sheet, and the control of the parameters required for higher efficiency solar cells. Although significant sheet cost reductions were made, the technology advancements required to meet the task cost goals were not achieved.

Briglio, A.↗
DOE OSTI2020

Fabrication processes for effectively transparent contacts

In conventional solar cells with metal contacts, a non-negligible fraction of the incoming solar power is immediately lost either through absorption or reflection upon interaction with the contacts. Effectively transparent contacts (“ETCs”) for solar cells can be referred to as three-dimensional contacts designed to redirect incoming light onto a photoabsorbing surface of a solar cell. In many embodiments, the ETCs have triangular cross-sections. Such ETCs can be placed on a photoabsorbing surface such that at least one of their sides forms an angle with the photoabsorbing surface. In this configuration, the ETCs can redirect incident light onto the photoabsorbing surface, mitigating or eliminating reflection loss compared to conventional solar cells. When constructed in accordance with a number of embodiments of the invention, ETCs can be effectively transparent and highly conductive.

14 SOLAR ENERGY↗
NASA NTRS1984

Advanced photovoltaic experiment (S0014)

The advanced photovoltaics-related experiments for investigating a portion of the solar spectrum and the effect of the space environment on photovoltaics. The information will be used to provide correlation between space and ground testing and also to provide for more accurate performance measurement in the laboratory. Specific objectives of these experiments are to provide information on the performance and endurance of advanced and conventional solar cells, to improve reference standards for photovoltaic measurements, and to measure the energy distribution in the extraterrestrial solar spectrum. Data to be obtained will include temperatures and short-circuit current of the samples. Six-point current-voltage (I-V) characteristics will be obtained for selected samples. These data will be recorded once a day during the flight. Orbit data will be correlated with preflight and postflight measurement of the samples.

Bradhorst, H. W., Jr.↗
NASA NTRS1971

Fast response solar array simulator

Tradeoff studies to determine the design requirements for a fast response solar array simulator capable of delivering output power in the range of 20 to 5000 watts are reported. The studies were divided into four major areas: frequency and transient response considerations, digital versus analog characteristic generation and programming, optimum power module size, and accuracy considerations. Based on an evaluation of the tradeoffs, a reference design was selected with a forward biased solar cell as an analog reference, and with current accuracy of + or - 0.5% of the short circuit setting.

Zerbel, D. W.↗
NASA NTRS1978

Results of the 1974 through 1977 NASA/JPL balloon flight solar cell calibration program

From 1974 through 1977, seven solar cell calibration flights and two R&D flights with a spectroradiometer as a payload were attempted. There were two R&D flights, and one calibration flight that failed. Each calibration flight balloon was designed to carry its payload to an altitude of 36.6 km (120 kft). The R&D flight balloons were designed for a payload altitude of 47.5 km (150 kft). At the end of the flight period, the upper (solar cell calibration system) and lower (consolidated instrument package (DIP) payloads were separated from the balloon and descend via parachutes. The calibrated solar cells recovered in this manner were used as primary intensity reference standards during solar simulator testing of solar cells and solar arrays with similar spectral response characteristics. This method of calibration has become the most widely accepted technique for developing space standard solar cells.

Sidwell, L. B.↗
NASA NTRS1976

Terrestrial photovoltaic measurements, 2

The following major topics are discussed; (1) Terrestrial solar irradiance; (2) Solar simulation and reference cell calibration; and (3) Cell and array measurement procedures. Numerous related subtopics are also discussed within each major topic area.

Source record↗
NASA NTRS1979

Solar power satellite system definition study. Volume 1: Executive summary

Configuration concepts, option sizes, and systems definitions study design evolutions are reviewed. The main features of the present reference design silicon solar cell solar power satellite are described, as well as the provisions for space construction and support systems. The principal study accomplishments and conclusions are summarized according to the following tasks: (1) baseline critique; (2) construction and maintenance; (3) industrial complex needs, cost estimates, and production capacity; (4) launch complex requirements at KSC or at an offshore facility; (5) integration of the SPS/ground power network; (6) technology advancement and development; (7) costs and schedules; and (8) exploratory technology: laser annealing of solar cells degraded by proton irradiation, and a fiber-optic phase distribution link at 980 MHz.

Source record↗
DOE OSTI2020

Chapter 12: Photoelectron Spectroscopy Methods in Solar Cell Research

Photoelectron spectroscopy (PES), also referred to as photoemission spectroscopy, is a direct experimental method for assessing the chemical and electronic properties of materials. The technique is becoming increasingly important in the research of photovoltaic (PV) devices--where, more specifically, X-ray photoelectron spectroscopy (XPS) is used primarily to measure the chemical properties such as composition and contamination of solar cell materials, whereas ultraviolet photoelectron spectroscopy (UPS) reveals key electronic properties such as work function and electronic energy-level positions. PES is a surface-sensitive technique ideally suited for the analysis of thin films and interfaces, either completed ones or during their formation process. Because the new generation of PV devices comprise a multitude of complex interfaces--each of which plays a critical role for performance and functionality--PES analysis of functional cell components has gained even more relevance.

photoelectron spectroscopy↗
NASA NTRS1980

Radiation Damage Workshop report

The starting material, cell design/geometry, and cell processing/fabrication for silicon and gallium arsenide solar cells are addressed with reference to radiation damage. In general, it is concluded that diagnostic sensitivities and material purities are basic to making significant gains in end-of-life performance and thermal annealability. Further, GaAs material characterization is so sketchy that a well defined program to evaluate such material for solar cell application is needed to maximize GaAs cell technology benefits.

Rahilly, W. P.↗
DOE OSTI2020

Ultra-thin passivation layers in Cu(In,Ga)Se 2 thin-film solar cells: full-area passivated front contacts and their impact on bulk doping

In the search for highly transparent and non-toxic alternative front layers replacing state-of-the-art CdS in Cu(In,Ga)Se 2 thin-film solar cells, alternatives rarely exceed reference devices in terms of efficiency. Full-area ultra-thin aluminium oxide tunnelling layers do not require any contact patterning and thus overcome the main drawback of insulating passivation layers. Even a few monolayers of aluminium oxide can be deposited in a controlled manner by atomic layer deposition, they show excellent interface passivation properties, low absorption, and suitable current transport characteristics on test devices. Depositing a ZnO-based transparent front contact, however, results in extremely poor solar cell performance. The issue is not necessarily a low quality of the alternative front layer, but rather the intricate relation between front layer processing and electronic bulk properties in the absorber layer. We identify three challenges critical for the development of novel front passivation approaches:(i) both Cd and Zn impurities beneficially reduce the high native net dopant concentration in the space charge region, (ii) sputter deposition of ZnO damages the passivation layer resulting in increased interface recombination, (iii) thermal treatments of devices with ZnO layer result in substantial Zn diffusion, which can penetrate the full absorber thickness already at moderate temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗