Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface recombination velocities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Determination of lifetime and surface recombination velocity of p-n junction solar cells and diodes by observing transients

The unified view of transient methods for the determination of recombination lifetime tau and back surface recombination velocity S presented here for silicon solar cells and diodes attempts to define limitations of existing methods and to evolve improvements. The presence of sizable junction capacitance for silicon devices under forward voltage invalidates the use of conventional open-circuit voltage decay (OCVD) and reverse recovery. This led Green (1983) to his method of compensated open-circuit voltage decay, in which the addition of an external resistor shunting the solar cell partially corrects for the presence of the junction capacitance. Setting this resistance to zero produces an electrical short-circuit current-decay method, which has the advantage of enabling determination of both tau and S. In an alternate approach, one may insert the functional dependence of the junction capacitance on forward voltage. This new method, denoted by the acronym OCVDCAP, enables the determination of tau with apparently greater accuracy than that obtained by previous methods utilizing voltage transients. But OCVDCAP has in common with the previous methods that it determines tau only and has practical utility only for determining tau of long-base devices. This means that it is useful only for thick base regions. In principle, however, it has an advantage over short-circuit current decay: it requires only pressure contacts, not ohmic contacts, and therefore may be used to determine tau after key processing steps in manufacturing.

Lindholm, Fredrik A.↗
NASA NTRS1977

Surface recombination velocity and diffusion length of minority carriers in heavily doped silicon layers

Quantitative analysis of the electron beam-induced current and the dependence of the effective diffusion length of the minority carriers on the penetration depth of the electron beam were employed for the analysis of the carrier recombination characteristics in heavily doped silicon layers. The analysis is based on the concept of the effective excitation strength of the carriers which takes into consideration all possible recombination sources. Two dimensional mapping of the surface recombination velocity of P-diffused Si layers will be presented together with a three dimensional mapping of minority carrier lifetime in ion implanted Si. Layers heavily doped with As exhibit improved recombination characteristics as compared to those of the layers doped with P.

Gatos, H. C.↗
NASA NTRS1985

Phenomena Simulation for Heavy Doping and Surface Recombination Velocity

The theoretical models now available that characterize heavily doped (highly conducting) regions in silicon are survyed. Analytical and numerical approaches that determine the influence of such regions on the conversion efficiency of solar cells are examined. Although dilutely doped silicon is well characterized except for some disagreement about optical absorption coefficients, what exists now for heavily doped silicon and its interplay with adjoining regions is an incomplete theory in which not all contributers to transport, recombination, generation, and trapping are defined. Further, the parameters relating to these mechanisms and their values as determined by experiment are subject to various interpretations. The characterization of heavily doped silicon is treated not as a theory but rather as an imperfectly articulated and incompletely formalized body of experience. This view is intended to help point the way toward the attainment of a more complete of heavily doped silicon and thereby toward more informed designs of solar cells. Because computer programs constitute tools both for design and for estimating performance limits, the review includes some remarks pertinent to existing and developing programs.

Lindholm, F. A.↗
NASA NTRS1987

Measurement of minority carrier lifetimes and surface recombination velocities in solar cells

A generic comparison has been carried out of all methods for recombination parameter determination that are based on measurement of a current and/or voltage in either steady-state, transient, or frequency-dependent approaches. The theoretical background for the time-dependent methods has been extended from prior work to include drift fields and be applicable to compound (multilayered) regions. The key findings were: (1) all methods have essentially the same limitations to determination of only the dominant recombination parameters; (2) open-circuit measurements have more sensitivity to the recombination parameters than short circuit measurements, but they present much more difficulty in eliminating spurious effects; (3) transient and frequency-dependent methods have exactly the same expressions for the relaxation constants and the breakpoint frequencies; and (4) in compound regions there exists only one set of relaxation constants for all the coupled layers. These constants include all relevant parameters of these layers. It is thus difficult to separate these parameters in time- or frequency-domain measurements. ASLBIC seems still to be the most suitable method for determination of emitter parameters.

Wolf, M.↗
DOE OSTI2021

Distinguishing bulk and surface recombination in CdTe thin films and solar cells using time-resolved terahertz and photoluminescence spectroscopies

Understanding the nature of recombination and its dependence on defects and interfaces is essential for engineering materials and contacts for higher open circuit voltage (V oc ) and power conversion efficiency in photovoltaic (PV) devices. Time-resolved photoluminescence (TRPL) has conventionally been used to evaluate recombination, but carrier redistribution often dominates the response at short times. In this work, we report on the quantification of carrier dynamics and recombination mechanisms by complementary use of both time-resolved terahertz spectroscopy (TRTS) and TRPL combined with numerical modeling of the continuity equations and Poisson’s equation. We have demonstrated this approach using CdTe thin films. A thin film stack with CdTe fabricated by vapor transport deposition and treated with CdCl 2 exhibited a bulk lifetime of 1.7 ± 0.1 ns, negligible CdTe/CdS interface recombination velocity, and back surface recombination velocity of 6.3 ± 1.3 x10 4 cm/s. In contrast, a film stack without CdCl 2 treatment had a bulk lifetime of only 68 ± 12 ps and a higher interface recombination velocity of 4 ± 2 x10 8 cm/s. By determining the locus and mechanisms of performance-limiting recombination, we can accelerate the development of thin-film PVs with higher V oc and efficiency. While the method has been demonstrated here using CdTe, it is also applicable to perovskites, Cu(InGa)Se 2 , Cu2ZnSn(S,Se) 4, and emerging technologies.

14 SOLAR ENERGY↗
NASA NTRS1986

Comments on determination of bandgap narrowing from activation plots

A determination is made of the temperature-dependence of emitter saturation current in bipolar devices which allows the derivation of a value for bandgap narrowing that is in better agreement with other determinations than previous results based on ohmic contact measurements of temperature dependence. The new values were obtained by varying the surface recombination velocity at the emitter surface. This improves accuracy by varying the minority carrier surface recombination velocity at the emitter contacts of otherwise indistinguishable emitters.

Park, J.-S.↗
DOE OSTI2021

Quantifying Bulk and Surface Recombination in CdTe Solar Cells Using Time-Resolved Terahertz Spectroscopy

Understanding the nature of recombination mechanisms is essential for higher power conversion efficiency in photovoltaic (PV) devices. Here we use a combination of time-resolved terahertz spectroscopy and numerical modeling to determine the bulk Shockley-Read-Hall lifetime and interface and back surface recombination velocities in CdTe thin film stacks. Furthermore, the measurement was facilitated by fabricating wire-grid device structures using conventional laser scribing. Evaluation of a glass/FTO/SnO2/CdS/CdTe stack treated with CdCl2 allowed separation of the CdTe absorber bulk lifetime, 1.6 ns, from the back surface recombination velocity, ~6x10 4 cm/s, and indicated that CdTe/CdS interface recombination velocity had no significant impact on carrier dynamics.

14 SOLAR ENERGY↗
NASA NTRS1989

Ultra-thin, light-trapping silicon solar cells

Design concepts for ultra-thin (2 to 10 microns) high efficiency single-crystal silicon cells are discussed. Light trapping allows more light to be absorbed at a given thickness, or allows thinner cells of a given Jsc. Extremely thin cells require low surface recombination velocity at both surfaces, including the ohmic contacts. Reduction of surface recombination by growth of heterojunctions of ZnS and GaP on Si has been demonstrated. The effects of these improvements on AM0 efficiency is shown. The peak efficiency increases, and the optimum thickness decreases. Cells under 10 microns thickness can retain almost optimum power. The increase of absorptance due to light trapping is considered. This is not a problem if the light-trapping cells are sufficiently thin. Ultra-thin cells have high radiation tolerance. A 2 microns thick light-trapping cell remains over 18 percent efficient after the equivalent of 20 years in geosynchronous orbit. Including a 50 microns thick coverglass, the thin cells had specific power after irradiation over ten times higher than the baseline design.

Landis, Geoffrey A.↗
NASA NTRS1985

Use of low energy hydrogen ion implants in high efficiency crystalline silicon solar cells

This program is a study of the use of low energy hydrogen ion implantation for high efficiency crystalline silicon solar cells. The first quarterly report focuses on two tasks of this program: (1) an examination of the effects of low energy hydrogen implants on surface recombination speed; and (2) an examination of the effects of hydrogen on silicon regrowth and diffusion in silicon. The first part of the project focussed on the measurement of surface properties of hydrogen implanted silicon. Low energy hydrogen ions when bombarded on the silicon surface will create structural damage at the surface, deactivate dopants and introduce recombination centers. At the same time the electrically active centers such as dangling bonds will be passivated by these hydrogen ions. Thus hydrogen is expected to alter properties such as the surface recombination velocity, dopant profiles on the emitter, etc. In this report the surface recombination velocity of a hydrogen emplanted emitter was measured.

Fonash, S. J.↗
NASA NTRS1994

Surface Passivation for 3-5 Semiconductor Processing: Stable Gallium Sulphide Films by MOCVD

Gallium sulphide (GaS) has been deposited on GaAs to form stable, insulating, passivating layers. Spectrally resolved photoluminescence and surface recombination velocity measurements indicate that the GaS itself can contribute a significant fraction of the photoluminescence in GaS/GaAs structures. Determination of surface recombination velocity by photoluminescence is therefore difficult. By using C-V analysis of metal-insulator-semiconductor structures, passivation of the GaAs with GaS films is quantified.

Macinnes, Andrew N.↗
NASA NTRS1974

The effect of Be/+/ ion implanted exponential and uniform impurity profiles on the electrical characteristics of GaAs solar cells

The high surface recombination velocity is the major deterrent to obtaining efficient GaAs solar cells. If, however, an electric field is built in at the surface, the carriers will be swept away from the surface thus minimizing the surface recombination velocity problem. It has been previously shown theoretically that an exponential impurity distribution in the doped region of the cell results in a built-in electric field. Ion implantation was used to produce solar cells with an exponential impurity profile and cells with uniform profiles. It is shown that cells with an exponential impurity profile have higher open-circuit voltage, fill factors, and spectral response than those with a uniform impurity profile.

Vaidyanathan, K. V.↗
NASA NTRS1985

Measuring Recombination Velocities in Solar Cells

Electron-beam scanning method suggested for determining back-surface recombination velocity, SB, of back-surface-field (BSF) solar photovoltaic cell. Recombination velocity important because smaller value correlated with smaller saturation current and therefore higher cell efficiency. Method involves analyzing short-circuit current measured while electron beam scanned along edge of cell.

Vonroos, O.↗
NASA NTRS1982

Reduction of solar cell efficiency by bulk defects across the back-surface-field junction

The degradation of solar cell performance due to bulk defects distributed across the back-surface field junction is analyzed in terms of a three-region developed-perimeter model. Families of curves are computed and their physical significance is discussed in detail with reference to three parameters used to characterize the defects: defect area, defect density, and defect surface recombination velocity. A reduction in the open-circuit voltage due to the presence of a defect is expressed as a function of the defect area, density, cell thickness, and defect surface recombination velocity. Numerical examples are presented to illustrate the importance of the particular defect parameters.

Sah, C. T.↗
DOE OSTI2021

Enabling bifacial thin film devices by developing a back surface field using Cu x AlO y

Bifacial solar cells have the potential to increase the energy yield per unit area over traditional monofacial devices without significant added cost, driving $/kWh costs lower and accelerating the adoption of solar photovoltaics. However, the performance of bifacial thin film solar cells significantly lags that achieved by crystalline silicon cells. Here we incorporate wide bandgap Cu x AlO y as a back buffer layer for CdTe devices and achieve a backside illuminated device with high current density and high fill factor. Moreover, these values remain nearly constant even as the absorber layer thickness changes, indicating that a fully-depleted device is not required for efficient charge collection. We show that this response is indicative of a back surface field, albeit with a persistent high back surface recombination velocity. By managing electron reflection, we achieved a backside illumination conversion efficiency of 7.1% and bifaciality of 0.55 for a 3.3 µm CdTe device and 8.0% and 0.62 for a 2 µm device. Future improvements can be made by identifying and incorporating a passivation material that reduces the back surface recombination velocity.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Diffusion length measurements in bulk and epitaxially grown 3-5 semiconductors using charge collection microscopy

Diffusion lengths and surface recombination velocities were measured in GaAs diodes and InP finished solar cells. The basic techniques used was charge collection microscopy also known as electron beam induced current (EBIC). The normalized currents and distances from the pn junction were read directly from the calibrated curves obtained while using the line scan mode in an SEM. These values were then equated to integral and infinite series expressions resulting from the solution of the diffusion equation with both extended generation and point generation functions. This expands previous work by examining both thin and thick samples. The surface recombination velocity was either treated as an unknown in a system of two equations, or measured directly using low e(-) beam accelerating voltages. These techniques give accurate results by accounting for the effects of surface recombination and the finite size of the generation volume.

Leon, R. P.↗
NASA NTRS1987

Diffusion length measurement in bulk and epitaxially grown III-V semiconductors using charge collection microscopy

Diffusion lengths and surface recombination velocities were measured in GaAs diodes and InP finished solar cells. The basic technique used was charge collection microscopy, also known as electron beam induced current (EBIC). The normalized currents and distances from the pn junction were read directly from the calibrated curves obtained while using the line-scan mode in an SEM. These values were then equated to integral and infinite series expressions resulting from the solution of the diffusion equation with both extended-generation and point-generation functions. This expands previous work by examining both thin and thick samples. The surface recombination velocity was either treated as an unknown in a system of two equations or measured directly using low e(-) beam accelerating voltages. These techniques give accurate results by accounting for the effects of surface recombination and the finite size of the generation volume.

Leon, R. P.↗