Search NASA⌕ Search

SEARCH · Search NASA

Results for “textured silicon”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Investigation of Backside Textures for Genesis Solar Wind Silicon Collectors

Genesis solar wind collectors were comprised of a suite of 15 types of ultrapure materials. The single crystal, pure silicon collectors were fabricated by two methods: float zone (FZ) and Czochralski (CZ). Because of slight differences in bulk purity and surface cleanliness among the fabrication processes and the specific vendor, it is desirable to know which variety of silicon and identity of vendor, so that appropriate reference materials can be used. The Czochralski method results in a bulk composition with slightly higher oxygen, for example. The CZ silicon array wafers that were Genesis-flown were purchased from MEMC Electronics. Most of the Genesis-flown FZ silicon was purchased from Unisil and cleaned by MEMC, although a few FZ wafers were acquired from International Wafer Service (IWS).

Gonzalez, C. P.↗
NASA NTRS1988

Processing, texture and mechanical properties of sintered silicon carbide

With regard to its favorable properties, in particular those shown at high temperatures, silicon carbide is of great interest for applications related to the construction of engines and turbines. Thus, silicon carbide could replace heat-resisting alloys with the objective to achieve a further increase in operational temperature. The present investigation is concerned with approaches which can provide silicon carbide material with suitable properties for the intended applications, taking into account the relations between characteristics of the raw material, material composition, sinter conditions, and results of the sintering process. The effects of density and texture formation on the mechanical properties are studied. It is found that a dense material with a fine-grained microstructure provides optimal mechanical properties, while any deviation from this ideal condition can lead to a considerable deterioration with respect to the material properties.

Landfermann, H.↗
NASA NTRS1976

Nonpropulsive applications of ion beams

Eight centimeter ion beam sources utilizing xenon and argon have been developed that operate over a wide range of beam energies and currents. Three types of processes have been studied: sputter deposition, ion beam machining, and ion beam surface texturing. The broad range of source operating conditions allows optimum sputter deposition of various materials. An ion beam source was used to ion mill laser reflection holograms using photoresist patterns on silicon. Ion beam texturing was tried with many materials and has a multitude of potential applications.

Hudson, W. R.↗
NASA NTRS1976

Nonpropulsive applications of ion beams

This paper describes the results of an investigation of the nonpropulsive applications of electric propulsion technology. Eight centimeter ion beam sources utilizing xenon and argon have been developed that operate over a wide range of beam energies and currents. Three types of processes have been studied - sputter deposition, ion beam machining, and ion beam surface texturing. The broad range of source operating conditions allows optimum sputter deposition of various materials. An ion beam source has also been used to ion mill laser reflection holograms using photoresist patterns on silicon. Ion beam texturing has been tried with many materials and has a multitude of potential applications.

Hudson, W. R.↗
NASA NTRS1980

Characterization of three types of silicon solar cells for SEPS deep-space missions. Volume 2: Current voltage characteristics of Solarex textured P(+)8 to 10 mil, planar P(+)8 to 10 mil and planar P(+)2 mil cells as a function of temperature and intensity

Three types of high performance silicon solar cells, textured P(+)8 to 10 mil, planar P(+)8 to 10 mil and planar P(+)2 mil were evaluated for their low temperature and low intensity (LTLI) performance. Sixteen cells of each type were subjected to 11 temperatures and 9 intensities. The textured P(+)8 to 10 mil cells provided the best performance both at 1 astronomical unit and at LTLI conditions. The average efficiencies of this cell were 14.5 percent at 1 solar constant/+25 C and 18.7 percent at 0.086 solar constant/-100 C.

Whitaker, A. F.↗
NASA NTRS1992

TEM studies of a circumstellar rock

Reported here is the discovery of crystals of titanium carbide in a grain of silicon carbide which formed as a circumstellar dust particle in the atmosphere of a carbon-rich star. Just as in the case of terrestrial rocks, whose assemblage of minerals gives us clues to the composition and conditions of the environment in which they formed, the titanium carbide crystals and their textural relationship to the silicon carbide give us important clues to the nature of the stellar atmosphere in which they formed. From microscopic studies of the relationships between the atomic planes of the silicon carbide and the titanium carbide, we can show that the titanium carbide cannot have existed as already-formed crystals in a gas around which silicon carbide subsequently condensed. An alternative possibility is that both minerals grew quickly and simultaneously from condensing gas in the rapidly cooling and expanding stellar atmosphere. Other microscopic features of the silicon carbide, such as abundant atomic layer disorder and crystal twinning, similarly suggest rapid grain growth. However, another possibility is that the titanium carbide grew inside of the silicon carbide by diffusion of titanium atoms. Our calculations suggest that this scenario is less likely, given the relatively short times (a year or less) for which stellar condensates can be expected to be exposed to temperatures high enough to make diffusion sufficiently rapid.

Bernatowicz, Thomas J.↗
NASA NTRS1980

Development of a high efficiency thin silicon solar cell

Significant improvements in open-circuit voltage and conversion efficiency, even on relatively high bulk resistivity silicon, were achieved by using a screen-printed aluminum paste back surface field. A 4 sq cm 50 micron m thick cell was fabricated from textured 10 omega-cm silicon which had an open-circuit voltage of 595 mV and AMO conversion efficiency at 25 C of 14.3%. The best 4 sq cm 50 micron thick cell (2 omega-cm silicon) produced had an open-circuit voltage of 607 mV and an AMO conversion efficiency of 15%. Processing modifications are described which resulted in better front contact integrity and reduced breakage. These modifications were utilized in the thin cell pilot line to fabricate 4 sq cm cells with an average AMO conversion efficiency at 25 C of better than 12.5% and with lot yields as great as 51% of starts; a production rate of 10,000 cells per month was demonstrated. A pilot line was operated which produced large area (25 cm) ultra-thin cells with an average AMO conversion efficiency at 25 deg of better than 11.5% and a lot yield as high as 17%.

Storti, G.↗
NASA NTRS1978

Thin silicon solar cell performance characteristics

Refined techniques for surface texturizing, back surface field and back surface reflector formation were evaluated for use with shallow junction, single-crystal silicon solar cells. Each process was characterized individually and collectively as a function of device thickness and bulk resistivity. Among the variables measured and reported are open circuit voltage, short circuit current and spectral response. Substantial improvements were obtained by the utilization of a low cost aluminum paste process to simultaneously remove the unwanted n(+) diffused region, form the back surface field and produce an ohmic contact metallization. The highly effective BSF which results from applying this process has allowed fabrication of cells 0.05 mm thick with initial outputs as high as 79.5 mW/4 sq cm (28 C, AM0) and superior electron radiation tolerance. Cells of 0.02 mm to 0.04 mm thickness have been fabricated with power to mass ratios well in excess of 2 watts per gram.

Gay, C. F.↗
NASA NTRS1979

Solar cell module

An improved solar cell module for use in terrestrial environments is disclosed. It is characterized by: (1) an internally reflective plate having a planar surface of incidence and an opposed textured surface (2) a plurality of uniformly spaced silicon solar cells having the active surfaces thereof bonded to portions of the textured surface, and (3) a layer of diffusely reflective matter applied to the textured surface in surrounding relation with the solar cells for reflecting solar energy. The solar energy then strikes the surface of incidence at such angles as to be internally re-reflected and caused to progress toward the active surfaces of the solar cells, whereby concentration of incident flux on the solar cell is achieved without increased module depth.

Shepard, N. F., Jr.↗
NASA NTRS1979

Mechanical and chemical effects of ion-texturing biomedical polymers

To determine whether sputter etching may provide substantial polymer surface texturing with insignificant changes in chemical and mechanical properties, an 8 cm beam diameter, electron bombardment, argon ion source was used to sputter etch (ion-texture process) nine biomedical polymers. The materials included silicone rubber, 32% carbon impregnated polyolefin, polyoxymethylene, polytetrafluoroethylene, ultrahigh molecular weight (UHMW) polyethylene, UHMW polyethylene with carbon fibers (10%), and several polyurethanes (bioelectric, segmented, and cross linked). Ion textured microtensile specimens of each material except UHMW polyethylene and UHMW polyethylene with 10% carbon fibers were used to determine the effect of ion texturing on tensile properties. Scanning electron microscopy was used to determine surface morphology changes, and electron spectroscopy for chemical analysis was used to analyze the near surface chemical changes that result from ion texturing. Ion energies of 500 eV with beam current densities ranging from 0.08 to 0.19 mA/sq cm were used to ion texture the various materials. Standard microtensile specimens of seven polymers were exposed to a saline environment for 24 hours prior to and during the tensile testing. The surface chemical changes resulting from sputter etching are minimal in spite of the often significant changes in the surface morphology.

Weigand, A. J.↗
NASA NTRS1979

Development of an Improved High Efficiency Thin Silicon Solar Cell

Breakage and front contact failure in high efficiency, textured ultrathin cells was reduced as a consequence of the introduction of process modifications. In a small production run, over one hundred ultrathin cells, having an average AMO efficiency of 13%, were fabricated from 10-25 ohm cm silicon. An in-house aluminum paste for back surface field formation was developed that resulted in cell efficiencies equivalent to those from commercial pastes. The quality of the back surface field was found to be dependent on the orientation of the silicon slice during alloying.

Storti, G.↗
NASA NTRS1984

The NASA photovoltaic technology program

The NASA Office of Aeronautical and Space Technology OAST Program in space photovoltaics is reviewed. From the perspective of national landmark mission requirements and five year and 25-year long range plans, the texture of the program is revealed. Planar silicon and concentrator GaAs array technology advances are discussed. Advances in lightweight (50 micro cell) arrays and radiation tolerance research are presented. Recent progress in cascade cells and ultralightweight GaAs planar cells is noted. Progress in raising silicon cell voltage to its theoretical maximum is detailed. Advanced concepts such as plasmon converters and the Long Duration Exposure Facility LDEF flight experiments pertaining to solar cell and array technology are also shown.

Mullin, J. P.↗
NASA NTRS1985

High Lifetime Solar Cell Processing and Design

In order to maximize efficiency a solar cell must: (1) absorb as much light as possible in electron-hole production, (2) transport as large a fraction as possible of the electrons to the n-type terminal and holes to the p-type terminal without their first recombining, and (3) produce as high as possible terminal voltage. Step (1) is largely fixed by the spectrum of sunlight and the fundamental absorption characteristics of silicon, although some improvements are possible through texturizing induced light trapping and back surface reflectors. Steps (2) and (3) are, however, dependent on the recombination mechanisms of the cell. The recombination, on the contrary, is strongly influenced by cell processing and design. Some of the lessons during the development of point-contact-cell are discussed. Cell dependence on recombination, surface recombination, and contact recombination are discussed. Results show the overwhelming influence of contact recombination on the operation of the cell when the other sources of recombination are reduced by careful processing.

Swanson, R. M.↗
NASA NTRS1984

The NASA photovoltaic technology program

The NASA Office of Aeronautical and Space Technology OAST Program in space photovoltaics is reviewed. From the perspective of national landmark mission requirements and five year and 25-year long range plans, the texture of the program is revealed. Planar silicon and concentrator GaAs array technology advances are discussed. Advances in lightweight (50 micro cell) arrays and radiation tolerance research are presented. Recent progress in cascade cells and ultralightweight GaAs planar cells is noted. Progress in raising silicon cell voltage to its theoretical maximum is detailed. Advanced concepts such as plasmon converters and the Long Duration Exposure Facility LDEF flight experiments pertaining to solar cell and array technology are also shown.

Mullin, J. P.↗
NASA NTRS2011

Cryo-Etched Black Silicon for Use as Optical Black

Stray light reflected from the surface of imaging spectrometer components in particular, the spectrometer slit degrade the image quality. A technique has been developed for rapid, uniform, and cost-effective black silicon formation based on inductively coupled plasma (ICP) etching at cryogenic temperatures. Recent measurements show less than 1-percent total reflectance from 350 2,500 nm of doped black silicon formed in this way, making it an excellent option for texturing of component surfaces for reduction of stray light. Oxygen combines with SF6 + Si etch byproducts to form a passivation layer atop the Si when the etch is performed at cryogenic temperatures. Excess flow of oxygen results in micromasking and the formation of black silicon. The process is repeatable and reliable, and provides control over etch depth and sidewall profile. Density of the needles can be controlled to some extent. Regions to be textured can be patterned lithographically. Adhesion is not an issue as the nanotips are part of the underlying substrate. This is in contrast to surface growth/deposition techniques such as carbon nanotubes (CNTs). The black Si surface is compatible with wet processing, including processing with solvents, the textured surface is completely inorganic, and it does not outgas. In radiometry applications, optical absorbers are often constructed using gold black or CNTs. This black silicon technology is an improvement for these types of applications.

Yee, Karl Y.↗
NASA NTRS1979

Process Development for Automated Solar Cell and Module Production. Task 4: Automated Array Assembly

A baseline sequence for the manufacture of solar cell modules was specified. Starting with silicon wafers, the process goes through damage etching, texture etching, junction formation, plasma edge etch, aluminum back surface field formation, and screen printed metallization to produce finished solar cells. The cells were then series connected on a ribbon and bonded into a finished glass tedlar module. A number of steps required additional developmental effort to verify technical and economic feasibility. These steps include texture etching, plasma edge etch, aluminum back surface field formation, array layup and interconnect, and module edge sealing and framing.

Source record↗
NASA NTRS1978

The Automated Array Assembly Task of the Low-cost Silicon Solar Array Project, Phase 2

An advanced process sequence for manufacturing high efficiency solar cells and modules in a cost-effective manner is discussed. Emphasis is on process simplicity and minimizing consumed materials. The process sequence incorporates texture etching, plasma processes for damage removal and patterning, ion implantation, low pressure silicon nitride deposition, and plated metal. A reliable module design is presented. Specific process step developments are given. A detailed cost analysis was performed to indicate future areas of fruitful cost reduction effort. Recommendations for advanced investigations are included.

Coleman, M. G.↗
NASA NTRS1978

Development of an improved high efficiency thin silicon solar cell

Efforts were concerned with optimizing techniques for thinning silicon slices in NaOH etches, initial investigations of surface texturing, variation of furnace treatments to improve cell efficiency, initial efforts on optimization of gridline and cell sizes and Pilot Line fabrication of quantities of 2 cm x 2 cm 50 micron thick cells.

Lindmayer, J.↗