Search NASA⌕ Search

SEARCH · Search NASA

Results for “water absorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Machinable, high‐conductivity NaSICON through mitigation of humidity effects during solid‐state synthesis

The Na + super ion conductor (NaSICON, Na 1+x Zr 2 Si x P 3-x O 12 ) is a solid electrolyte well-known for fast, selective Na + transport at low temperatures, uniquely enabling sodium-based batteries. Producing high-quality NaSICON from solid-state methods, especially when cost-effective, potentially hygroscopic precursors are used, is not trivial. To understand and eliminate the influence of humidity during processing, a scheme was developed to reproducibly yield a high Na + conductivity (3.75 mS/cm at 25°C, 81.7 mS/cm at 150°C), high density (97%), and machinable NaSICON without the use of binders, sintering aids, or dopants. Controlled humidity studies over 20%–50% RH coupled with thermal, structural, and electrical analysis reveal that calcination temperatures < 1000°C leave NaSICON processing susceptible to water absorption at > 20% RH due to the presence of hygroscopic Na 3 PO 4 and Na 2 CO 3 during shaping, pressing, and sintering. Water absorption results in NaSICON with lower densities, machinability, and Na+ conductivity, due to impaired intergranular Na+ transport. At the other extreme, fully converting precursor to the NaSICON phase at 1230°C before pressing and sintering leads to poor conductivity and density. By calcining at 1000°C, excellent quality NaSICON may be produced under a range of laboratory environments, enabling low-cost production of high-conductivity, machinable NaSICON necessary the ever-growing energy storage market.

NaSICON↗
DOE OSTI2021

Deliquescence of eutectic LiCl-KCl diluted with NaCl for interim waste salt storage

Molten eutectic LiCl-KCl salt is a widely used electrolyte for electrorefining uranium from spent nuclear fuel. Due to the hygroscopic nature of this salt, careful handling and storage of solidified waste electrorefiner (ER) salt is required to avoid deliquescence and corrosion of container materials. This study investigated a potential processing path for reducing the deliquescence through dilution with NaCl. The hydration behavior of LiCl-KCl salts diluted with NaCl was evaluated in terms of mass gain due to mass of water absorption, visual evidence of deliquescence, and visual evidence of corrosion to stainless steel containers in a humid air environment. Pure eutectic LiCl-KCl exhibited a 50 mass% increase due to water absorption and showed signs of deliquescence after 24 hours. 89 mass% NaCl was required in order to prevent deliquescence. Dilution with 89% NaCl was also found to protect corrosion to stainless steel crucibles. Corrosion, thus, appears to require deliquescence. While NaCl dilution greatly decreases steady state hydration and eliminated deliquescence, storage volume is increased ~10x.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Synthesis and characterization of super occluded LiCl-KCl in zeolite-4A as a chloride salt waste form intermediate

Here, this paper reports the hygroscopic properties of eutectic LiCl-KCl after absorption into zeolite-4A, up to salt loadings of 75 wt%. Samples of the salt occluded zeolite were hydrated in a humidity chamber at constant temperature and relative humidity for up to 100 h. At up to 45 wt% salt loading, the un-occluded phase of salt consisted primarily of NaCl, which forms when the Na + ions present in the zeolite framework exchange with Li + and K + ions from the eutectic LiCl-KCl. This results in minimal water absorption and corrosion of contacted stainless steel. At greater than 45 wt% salt loading, water absorption and corrosion progressively worsened. The mixture has a significant amount of excess LiCl-KCl, making it highly hygroscopic. This study reveals an option for the intermediate treatment of waste salt from spent nuclear fuel electrorefiners that could facilitate it to be stored in a non-inert atmosphere for extended periods of time before final conversion into a permanent waste form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Off-spec fly ash-based lightweight aggregate properties and their influence on the fresh, mechanical, and hydration properties of lightweight concrete: A comparative study

An off-spec fly ash-based spherical lightweight aggregate (LWA), designated as Spherical Porous Reactive Aggregate (SPoRA), was manufactured through a lab pilot-scale production and its engineering properties, including specific gravity, dry rodded unit weight, water absorption, mechanical performance, and pore structure, were evaluated. Using SPoRA, lightweight concrete (LWC) samples were made and their fresh, mechanical, and hydration properties were assessed and compared with LWC samples made using two commercial LWA available in the US market. The results indicated that fine and coarse SPoRA had 72 h water absorption capacities of 16.4 % and 20.9 %, respectively, which were higher than that of the two commercial LWAs. Higher saturated surface dry specific gravity of SPoRA compared to commercial LWAs led to a higher fresh density for the corresponding LWC. Using X-ray computed tomography, large spherical type pores were observed in SPoRA similar to those in the commercial slate-based LWA. Additionally, the pore size distribution of SPoRA, characterized by a dynamic vapor sorption analyzer, indicated that more than 97 % of the pores had diameters greater than 50 nm. SPoRA’s average bulk crushing strength was 6.8 MPa which was smaller than commercial LWA and was potentially attributed to the differences in manufacturing processes. Nonetheless, SPoRA LWC with 28 days compressive strength of 29 MPa passed the ASTM C330 requirement and had a comparable strength with LWC prepared with the commercial LWAs indicating lesser importance for the LWA strength. SPoRA LWC had a flowability of 5 % compared to LWC prepared with commercial LWAs having flowability of 18 %. This observation was potentially related to the fluxing agent used in the SPoRA production. SPoRA had a 70 % degree of hydration at 12 days which was comparable with that of LWC prepared with commercial LWA.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhancement of the Physical and Mechanical Properties of Cellulose Nanofibril-Reinforced Lignocellulosic Foams for Packaging and Building Applications

Biobased foams have the potential to serve as eco-friendly alternatives to petroleum-based foams, provided they achieve comparable thermomechanical and physical properties. We propose a facile approach to fabricate eco-friendly cellulose nanofibril (CNF)-reinforced thermomechanical pulp (TMP) fiber-based foams via an oven-drying process with thermal conductivity as low as 0.036 W/(m·K) at a 34.4 kg/m3 density. Acrodur®, iron chloride (FeCl3), and cationic polyacrylamide (CPAM) were used to improve the foam properties. Acrodur® did not have any significant effect on the foamability and density of the foams. Mechanical, thermal, cushioning, and water absorption properties of the foams were dependent on the density and interactions of the additives with the fibers. Due to their high density, foams with CPAM and FeCl3 at a 1% additive dosage had significantly higher compressive properties at the expense of slightly higher thermal conductivity. There was slight increase in compressive properties with the addition of Acrodur®. All additives improved the water stability of the foams, rendering them stable even after 24 h of water absorption.

Chemistry↗
DOE OSTI2026

Environmental Durability Assessment and Development of Subcomponent Test Methods for Advanced Materials in Marine Energy Applications

Marine energy developers are beginning to rely more heavily on advanced composite materials for their load-bearing structures. Understanding how these materials respond and degrade in harsh marine environments is a complex problem. Much research has been performed at smaller laboratory scales to understand the fundamental physical and chemical degradation mechanisms, but little structural testing research has been performed at larger scales to understand how these physical and chemical interactions scale and how they should be accounted for in the design process. The Advanced Materials project is a multilaboratory research collaboration that addresses these issues with the intention of reducing risks and barriers to marine energy developers wanting to adopt advanced composite materials. The National Laboratory of the Rockies has been playing a leading role in developing larger-scale testing infrastructure and test methods to validate complex numerical degradation models and standardize testing procedures to do so. This paper reviews past structural testing activities, how they have grown into current research activities, and how they will continue to evolve to directly address industry needs. This paper covers key research areas - large-scale water absorption and subsequent structural validation testing, qualification of bolted and adhesive connections, and combined submerged fatigue testing at increasing scales. It provides insights into the complex requirements for testing infrastructure and test method development to effectively qualify materials and certify marine energy structures for harsh marine environments. This research program paves the way for better guidance and standardization within the industry when adopting advanced composite materials.

16 TIDAL AND WAVE POWER↗
DOE OSTI2026

Environmental Durability Assessment and Development of Subcomponent Test Methods for Advanced Materials in Marine Energy Applications: Preprint

Marine energy developers are beginning to rely more heavily on advanced composite materials for their load bearing structures. Understanding how these materials respond and degrade in harsh marine environments is a complex problem. Much research has been performed at smaller laboratory scales to understand the fundamental physical and chemical degradation mechanisms, but little structural testing research has been performed at larger scales to understand how these physical and chemical interactions scale and how they should be accounted for in the design process. The Advanced Materials project is a multilaboratory research collaboration that has been addressing these issues with the intention of reducing risks and barriers to marine energy developers wanting to adopt advanced composite materials. The National Laboratory of the Rockies has been playing a leading role in developing larger scale testing infrastructure and test methods to validate complex numerical degradation models and standardize testing procedures to do so. This paper provides a review of past structural testing activities and how they have grown into current research activities and will continue to evolve into the future to directly address industry needs. This paper covers key research areas large-scale water absorption and subsequent structural validation testing, qualification of bolted and adhesive connections, and conducting combined submerged fatigue testing at increasing scales. This paper provides insights into the complex requirements for testing infrastructure and test method development to effectively qualify materials and certify marine energy structures for harsh marine environments. This research program paves the way for better guidance and standardization within the industry when adopting advanced composite materials.

16 TIDAL AND WAVE POWER↗
DOE OSTI2026

Handling and Properties of Methanol as a Marine Fuel

Given the increasing concern around greenhouse gas emissions and the decline in the availability of fossil fuels, there is increasing global demand to develop alternate fuels for maritime transportation that are sustainable and which have lower greenhouse gas emissions. Methanol is one such alternative fuel that has garnered considerable attention given its potential to be produced by more sustainable processes and its more favorable greenhouse gas emission profile in comparison with current fossil fuels. Understanding the physical and chemical properties of methanol under a range of conditions is essential for its development as a marine fuel. In this study, we seek to define physical and chemical properties of different methanol samples to simulate real-world storage conditions as these data are lacking in the literature. Several methanol samples were evaluated: nearly pure methanol; International Organization for Standardization (ISO) marine methanol (MM) grades A, B, and C; and methanol plus higher alcohols. We first evaluated all methanol samples for impurities, acetic acid content, density, and distillation range. We then characterized the effects of water absorption and found that methanol can easily absorb unacceptable water content from humid air within hours, necessitating storage conditions that prevent this process. In eight-week aging experiments at 20 °C and 40 °C in ambient air, we did not observe significant oxidation for any of the methanol samples; however, we did observe increases in acid number. We assessed the impact of contamination of methanol with water, marine gas oil (MGO), and an MGO–biodiesel mixture on density, viscosity, distillation range, and lubricity. Finally, we show that MGO contamination of methanol results in a slight increase in sooting tendency. In aggregate, our results provide an in-depth analysis of physical and chemical properties of methanol as well as the impacts of storage conditions and impurities on the properties of fuel methanol.

09 BIOMASS FUELS↗
DOE OSTI2025

Bio-Oil Impact on Water Diffusion and Durability of Bitumen: Influence of Aging and Salinity

Bio-oils derived from inexpensive biomass offer environmentally friendly options for modifying bitumen for improved durability or rejuvenating aged material, although their impact on bitumen moisture resistance can be mixed. A better understanding of water diffusion into bitumen and its interactions with bio-oil compounds would aid the development of effective bio-oils. In this study, the effect of water exposure on bio-oil-modified bitumen blends was examined by de-wetting contact angle measurements and differential FTIR spectroscopy. The bio-oils improved the anti-stripping behavior of the bitumen but also increased water absorption which could weaken cohesive strength. Short-term thermal aging increased water diffusion for all bitumen blends including the control, probably due to the presence of more oxidized compounds. Negative peaks of alkanes and polar groups in the differential FTIR data suggest the co-diffusion of surfactant molecules towards the bitumen-water interface. Basic pH increased de-wetting of some bitumen blends from silica, possibly by attacking the silica surface itself. The presence of salt in solution altered the bitumen surface composition through the formation of salt complexes with bitumen or bio-oil compounds. In particular, the formation of calcium-carboxylate complexes appeared to greatly improve anti-stripping effects of bio-oils. Water diffusion into most of the bitumen blends was insensitive to pH or salt concentration except for a few notable outliers. Identifying the compounds responsible for increasing or decreasing water diffusion in these outlier cases would be valuable developing future bio-oil formations that avoid or promote those compounds.

Hung, Albert M.↗
DOE OSTI2023

Performance of hydrophobic physical solvents for pre-combustion CO 2 capture at a pilot scale coal gasification facility

Here, in this paper, we present the first pilot plant data for hydrophobic physical solvents for CO 2 and H 2 S removal from coal-derived H 2 -rich syngas. Four physical solvents were tested under pre-combustion CO 2 capture conditions at bench scale and pilot plant scale: one baseline hydrophilic solvent and three hydrophobic solvents. The solvents were: (1) polyethylene-glycol-dimethyl ether (PEGDME), a hydrophilic solvent analog for the commercial process Selexol, (2) tributyl- phosphate (TBP), a commercially available hydrophobic solvent, (3) polyethylene glycol-poly(dimethylsiloxane) (PEG-PDMS-3), and (4) diethyl sebacate (CASSH-1), a novel, computationally screened hydrophobic solvent developed by the National Energy Technology Laboratory (NETL). All solvents were studied under pure gas (CO 2 /N 2 /H 2 /CH 4 ) equilibrium conditions at NETL followed by pilot plant testing with syngas at the University of North Dakota Energy & Environmental Research Center (UND EERC). Long term performance of CASSH-1 and PEDGME was then assessed with results compared to process simulation predictions. Within experimental uncertainties, all solvents showed comparable CO 2 absorption performance at above room temperature operation while the hydrophobic solvents had limited water uptake and low vapor pressure, which alleviates concerns related to corrosion, water absorption, and solvent loss to evaporation. These results indicate low viscosity, low vapor pressure hydrophobic solvents are a promising option for lower cost CO 2 capture from high pressure syngas applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Hidden features in the OH-stretching spectra of amino acid decorated air–water interfaces

Chemical reactivity at the air–water interface is governed by the interfacial solvation of reactive species. For instance, during aqueous amino acid-based CO 2 absorption, water reorganizes around the reactive sites and couples dynamically with reaction pathways, facilitating the reaction. In this context, surface-sensitive vibrational sum-frequency generation (vSFG) spectroscopy can probe the OH stretch vibrations of interfacial water and determine the solvation structures around reactants and products, thereby furthering our understanding of the role of interfacial solvation. However, vSFG spectra of the air–water interface in the presence of charged species can be remarkably complex; key species-bound local water structures with distinct orientations may be hidden beneath prominent vSFG peaks arising from water–water hydrogen bonds and remain difficult to resolve. Here, we measure and compute vSFG spectra of the water OH stretch at air–water interfaces decorated with amino acids in their zwitterionic and anionic forms, as well as equimolar mixtures of these forms with bicarbonate. The latter represents post-CO 2 -absorption conditions. We find that computing depth- and frequency-dependent spectral densities—decomposed into contributions from water molecules hydrogen-bonded exclusively to other water molecules, exclusively to amines, exclusively to carboxylates, or shared between these polar/charged groups—is indispensable for accurate interpretation of the vSFG spectra. Key findings include orientational flip-flop in water sub-layers, strong carboxylate-water H-bonding, and water orientational ordering extending into the bulk aqueous phase induced by anionic amino acids. Here, this study provides a computational spectroscopic platform for improved understanding of interfacial solvation relevant to interfacial reactivity.

Air-water interface↗
DOE OSTI2021

Solvation Dynamics of Wet Ethaline: Water is the Magic Component

The past two decades witnessed the development of a new type of solvent system, named deep eutectic solvents, which have become increasingly investigated because they offer new and potentially favorable properties, such as wide tunability in electrochemical, mechanical, and transport properties. Deep eutectic solvent (DES) systems are composed of at least one main solvent and an additional component that is meant to interrupt the original solvent/solvent interactions, thereby introducing lower melting points relative to each individual component. Ethaline (a 1:2 mole% mixture of choline chloride and ethylene glycol) is one of the most promising DES systems. However, it is also known to be very hygroscopic, which is a constant concern because water absorption during the use of ethaline alters its properties. Within this work, we demonstrate that modest amounts of water addition (1-10%) to ethaline are of little concern for practical use and can even lead to performance improvements, such as accelerated relaxation and solvation. In contrast, very small amounts of <1% of water lead to additional slowing of the solvent response. Thus, we suggest that the attempt to dry ethaline below 1% moisture is rather counter-productive if one attempts to achieve effective solvation and charge transport properties from DESs. This study investigates the effect of water content on the diffusional relaxation dynamics of ethaline. A set of independent spectroscopic experiments and computational simulations are aimed to provide insight into the solvent response of the DES system using femtosecond time-resolved absorption spectroscopy (fs-TA), broadband dielectric spectroscopy (BDS), nuclear magnetic resonance (NMR) diffusometry and broadband relaxometry, and molecular dynamics simulations (MDS) on ethaline with 0, 0.1, 1, 10, and 28.5wt% added water. For dry ethaline, we identify choline chloride as the rate-limiting solvation component in ethaline. However, the role of the solvent components changes gradually as water is added. Further, we provide quantitative solvent relaxation rates using the different presented time-resolved spectroscopic techniques and find remarkable agreement between them. Based on the solvent relaxation rates and combined with MDS, we develop a molecular understanding of the individual solvent components and their interactions in dry and wet ethaline with varying amounts of water content.

25 ENERGY STORAGE↗
DOE OSTI2022

Improving Reliability, Weight and Cost of Gas-Fired Absorption Heat Pumps

The objective of the project was to identify and verify a viable path for the use of aluminum tubes in evaporators for gas-fired ammonia-water absorption heat pumps (GAHP), via identification of a suitable alloy, coating, inhibitor, process, or combination, for the purpose of achieving weight and cost reduction.

03 NATURAL GAS↗
DOE OSTI2020

Cloud Atlas: High-precision HST/WFC3/IR Time-resolved Observations of Directly Imaged Exoplanet HD 106906b

HD 106906b is an ∼11M{sub Jup}, ∼15 Myr old directly imaged exoplanet orbiting at an extremely large distance from its host star. The wide separation (7.″11) between HD 106906b and its host star greatly reduces the difficulty in direct-imaging observations, making it one of the most favorable directly imaged exoplanets for detailed characterization. In this paper, we present HST/WFC3/IR time-resolved observations of HD 106906b in the F127M, F139M, and F153M bands. We have achieved ∼1% precision in the lightcurves in all three bands. The F127M lightcurve demonstrates marginally detectable (2.7σ significance) variability with a best-fitting period of 4 hr, while the lightcurves in the other two bands are consistent with flat lines. We construct primary-subtracted deep images and use these images to exclude additional companions to HD 106906 that are more massive than 4 M{sub Jup} and locate at projected distances of more than ∼500 au. We measure the astrometry of HD 106906b in two HST/WFC3 epochs and achieve precisions better than 2.5 mas. The position angle and separation measurements do not deviate from those in the 2004 HST/ACS/HRC images for more than 1σ uncertainty. We provide the HST/WFC3 astrometric results for 25 background stars that can be used as reference sources in future precision astrometry studies. Our observations also provide the first 1.4 μm water band photometric measurement for HD 106906b. HD 106906b’s spectral energy distribution and the best-fitting BT-Settl model have an inconsistency in the 1.4 μm water absorption band, which highlights the challenges in modeling atmospheres of young planetary-mass objects.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

ARES. II. Characterizing the Hot Jupiters WASP-127 b, WASP-79 b, and WASP-62b with the Hubble Space Telescope

This paper presents the atmospheric characterization of three large, gaseous planets: WASP-127 b, WASP-79 b, and WASP-62 b. We analyzed spectroscopic data obtained with the G141 grism (1.088–1.68 μm) of the Wide Field Camera 3 on board the Hubble Space Telescope using the Iraclis pipeline and the TauREx3 retrieval code, both of which are publicly available. For WASP-127 b, which is the least dense planet discovered so far and is located in the short-period Neptune desert, our retrieval results found strong water absorption corresponding to an abundance of log(H{sub 2}O) = −2.71{sub −1.05}{sup +0.78} and absorption compatible with an iron hydride abundance of log(FeH) = −5.25{sub −1.10}{sup +0.88}, with an extended cloudy atmosphere. We also detected water vapor in the atmospheres of WASP-79 b and WASP-62 b, with best-fit models indicating the presence of iron hydride, too. We used the Atmospheric Detectability Index as well as Bayesian log evidence to quantify the strength of the detection and compared our results to the hot Jupiter population study by Tsiaras et al. While all the planets studied here are suitable targets for characterization with upcoming facilities such as the James Webb Space Telescope and Ariel, WASP-127 b is of particular interest due to its low density, and a thorough atmospheric study would develop our understanding of planet formation and migration.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

An Unusual Transmission Spectrum for the Sub-Saturn KELT-11b Suggestive of a Subsolar Water Abundance

We present an optical-to-infrared transmission spectrum of the inflated sub-Saturn KELT-11b measured with the Transiting Exoplanet Survey Satellite (TESS), the Hubble Space Telescope (HST) Wide Field Camera 3 G141 spectroscopic grism, and the Spitzer Space Telescope (Spitzer) at 3.6 μm, in addition to a Spitzer 4.5 μm secondary eclipse. The precise HST transmission spectrum notably reveals a low-amplitude water feature with an unusual shape. Based on free-retrieval analyses with varying molecular abundances, we find strong evidence for water absorption. Depending on model assumptions, we also find tentative evidence for other absorbers (HCN, TiO, and AlO). The retrieved water abundance is generally ≲0.1× solar (0.001–0.7× solar over a range of model assumptions), several orders of magnitude lower than expected from planet formation models based on the solar system metallicity trend. We also consider chemical-equilibrium and self-consistent 1D radiative-convective equilibrium model fits and find that they, too, prefer low metallicities ([M/H] ≲ -2, consistent with the free-retrieval results). However, all of the retrievals should be interpreted with some caution because they either require additional absorbers that are far out of chemical equilibrium to explain the shape of the spectrum or are simply poor fits to the data. Finally, we find that the Spitzer secondary eclipse is indicative of full heat redistribution from KELT-11b’s dayside to nightside, assuming a clear dayside. These potentially unusual results for KELT-11b’s composition are suggestive of new challenges on the horizon for atmosphere and formation models in the face of increasingly precise measurements of exoplanet spectra.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Comparative analysis of the methods for quantitative determination of water content in skin from diffuse reflectance spectroscopy data

The predictive properties of methods aimed for estimating the water content in skin from the spectral diffuse reflection characteristics near the water absorption line in the near-IR spectral range are analysed. Numerical simulation data, experimental data on diffuse reflection from human skin phantoms, and data from the reference data set of human skin reflectance spectra are used to consider the possibility of gaining additional information about the water distribution in skin. The influence of variations in the scattering coefficient and oxyhaemoglobin concentration on the water content estimates is investigated. (paper)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Hygrothermal Aging and Thermomechanical Characterization of As-Manufactured Tidal Turbine Blade Composites

This study investigates the hygrothermal aging behavior and thermomechanical properties of as-manufactured glass fiber-reinforced epoxy and thermoplastic composite tidal turbine blades. The blades were previously deployed in a marine environment and subsequently analyzed through a comprehensive suite of material characterization techniques, including hygrothermal aging, dynamic mechanical analysis (DMA), tensile testing and X-ray computed tomography (XCT). Hygrothermal aging experiments revealed that while thermoplastic composites exhibited lower overall water absorption (0.78% vs. 0.47%), they had significantly higher diffusion coefficients than epoxy (2.1 vs. 12.1 × 10 −13 m 2 s −1 ), suggesting faster saturation in operational environments. DMA results demonstrated that water ingress caused plasticization in epoxy matrices, reducing the glass transition temperature and increasing damping (112 °C to 104 °C), while thermoplastic composites showed more stable thermal behavior (87 °C glass transition temperature). Tensile testing revealed substantial reductions in ultimate strength (>40%) for both materials after prolonged water exposure, with minimal change in elastic modulus, highlighting the role of matrix degradation over fiber reinforcement. XCT image analysis showed that both composites were manufactured with high quality: no large voids or cracks were present, and the degree of misalignment was low. These findings inform future marine renewable energy composite designs by emphasizing the critical influence of moisture on long-term structural integrity and the need for optimized material systems in harsh marine environments. This work provides a rare real-world comparison of epoxy and recyclable thermoplastic tidal turbine blades, showing how laboratory aging tests and advanced imaging reveal the influence of material and manufacturing choices on long-term marine durability.

16 TIDAL AND WAVE POWER↗