Search NASA⌕ Search

SEARCH · Search NASA

Results for “Separation standard”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Identification and Quantification of Photosynthetic Pigments in Algae (Laboratory Analytical Procedure (LAP))

The Laboratory Analytical Procedure (LAP) outlined here describes a method to quantitatively extract phytopigments from microalgae biomass, as well as to identify and quantify individual pigments based on separation and detection with a High-Performance Liquid Chromatography (HPLC) system coupled to a Diode Array Detector (DAD). Pigments were extracted with greater than 95 % extraction efficiency. Chromatographic conditions allowed for isomeric resolution between pigments and identification based on UV/Vis spectra and comparison to analytical standards.

09 BIOMASS FUELS↗
DOE OSTI2019

Eddy Flux and Meteorology over Deciduous Forest, Prairie, and Soybean Ecosystems in Missouri, USA, during the Total Solar Eclipse of 2017

Eddy fluxes and meteorology data are reported at high temporal resolution for three flux tower sites in Mid-Missouri before, during, and after the Total Solar Eclipse of August 21, 2017. Mid-Missouri experienced up to 2 minutes and 40 seconds of totality at around solar noon during the eclipse (Fig. 1). The sites are located in deciduous oak-hickory forest, native prairie, and soybean ecosystems (Table 1 and Fig. 3). Eddy fluxes were computed using a wavelet-based approach that permitted the calculation of two-minute mean fluxes without losing low frequency flux contributions (Fig. 2). During the eclipse, standard meteorological variables were sampled and recorded at 5 second intervals. The two-minute means of fluxes and meteorology are reported. This data product includes three data files in NetCDF (*.nc) format, three data dictionary files and a file-level metadata file in comma separate (*.csv) format, and a user guide in PDF (*.pdf) format.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS

The Marine Algae Industrialization Consortium (MAGIC) was formed to address pressing challenges in the commercialization of microalgae as a source of biofuel. The “Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS” project formally addressed two US Department of Energy Bioenergy Technologies Office (BETO) goals: (1) Model the sustainable supply of 1 million metric tonnes ash free dry weight (AFDW) cultivated algal biomass and (2) Demonstrate valuable co-products produced along with biofuel intermediates to increase value of algal biomass by 30%. To achieve these goals, the project demonstrated and validated high-value co-products to drive down the cost of biofuel by increasing the value of algae “co-products” towards increasing the selling price of total algae biomass as one of the key drivers of economics and adoption. This was accomplished through five core, interdependent tasks including: (1) strain selection to identify and deliver strains for mass culture, (2) mass culture using a hybrid cultivation system and following key operating parameters for downstream applications to provide algae feedstock, (3) recovery and conversion to evaluate two alternative methods to separate dry algae biomass into oil and residuals for downstream testing, (4) product assessment to determine biofuel, aquafeed or poultry feed product efficacy using algae biomass fractions as well as to provide critical performance data for valuation and (5) commercialization to use technoeconomic and life cycle assessments (TEA/LCA) as iterative design and assessment tools including consideration of target markets, competitors, and distribution channels to guide product assessment, development and valuation. A total of 46 peer-review publications, many open-access, provide detail of much of the work carried out and the results of the tasks. Additional reports and presentations provide other technical and public engagement material. At a high level, using a variety of approaches, more than 1000 marine microalgae strains were evaluated to ultimately identify the seven winners that were down-selected to be grown in mass culture. Strain selection demonstrated that there were no ‘super strains’ and that each candidate had strengths and limitations for specific products, growth conditions or operational considerations. Mass culture growth of these seven strains at >5000 L / 29 m 2 scale found that four them were suitable for product assessment. More than 250 kg of biomass was produced across hundreds of pond runs along with thousands of cultivation entries on the growth and biomass characteristics as well as environmental parameters. In the process, dozens of standard operating procedures were generated as was custom software to process and analyze cultivation data. Recovery and conversion of algae biomass demonstrated that a hexane solvent based extraction protocol was most effective at recovering oil (biocrude) from algae and four strains were processed to produce oil and lipid extracted algae (residuals) for downstream testing. Membrane-based oil separation was less successful, but may still be applicable to other commercial applications in the future. Product testing demonstrated that algae biocrude is of high quality and hydrotreating generated numerous fractions of high quality composition for fuel and lubricate based applications. Aquafeed studies performed at a variety of scales showed that both whole and defatted (lipid extracted algae) microalgae were suitable as a feed ingredient, but that the specifics of the fed animal and biochemical composition of the algae are critical factors when determining formulation. Similarly, poultry studies on whole and defatted microalgae generally showed positive outcomes on animal growth and health, with some microalgae providing enhanced nutritional composition of the animal product. Economic and life cycle assessments covered a wide range of possible commercialization and sustainability scenarios. Replacement value, improved product value added, consumer values marketing added valuation and improved animal health were considered as alternatives for microalgae valuation. Using the open pond system, algae productivity was identified as the key driver of commercialization economics, but combination of co-products (e.g. animal feed) with biofuel production substantially increased the total selling price of algae. Modeled microalgae selling price exceeded $\$$1500/tonne and could generate competitive biofuel selling prices below $\$$5 gallon gas equivalents using realistic algal productivities. Short (process scale) and longer (decadal trends) sustainability assessments show that marine microalgae can enhance the sustainability of energy production and lead to other realized benefits in water, fertilizer and land use for other sectors (e.g. agriculture). This project successfully demonstrated all of the components of an end-to-end process from mass microalgae cultivation and dewatering, to recovery and conversion of algae biomass components, to final product demonstration and process valuation; the combined results provide a framework for future commercialization of algae based biofuels.

09 BIOMASS FUELS↗
DOE OSTI2021

Nucleation is more than critical: A case study of the electroweak phase transition in the NMSSM

Electroweak baryogenesis is an attractive mechanism to generate the baryon asymmetry of the Universe via a strong first order electroweak phase transition. We compare the phase transition patterns suggested by the vacuum structure at the critical temperatures, at which local minima are degenerate, with those obtained from computing the probability for nucleation via tunneling through the barrier separating local minima. Heuristically, nucleation becomes difficult if the barrier between the local minima is too high, or if the distance (in field space) between the minima is too large. As an example of a model exhibiting such behavior, we study the Next-to-Minimal Supersymmetric Standard Model, whose scalar sector contains two SU(2) doublets and one gauge singlet. We find that the calculation of the nucleation probabilities prefers different regions of parameter space for a strong first order electroweak phase transition than the calculation based solely on the critical temperatures. Our results demonstrate that analyzing only the vacuum structure via the critical temperatures can provide a misleading picture of the phase transition patterns, and, in turn, of the parameter space suitable for electroweak baryogenesis.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Long-baseline quantum sensor network as dark matter haloscope

Ultralight dark photons constitute a well-motivated candidate for dark matter. A coherent electromagnetic wave is expected to be induced by dark photons when coupled with Standard-Model photons through kinetic mixing mechanism, and should be spatially correlated within the de Broglie wavelength of dark photons. Here we report the first search for correlated dark-photon signals using a long-baseline network of 15 atomic magnetometers, which are situated in two separated meter-scale shield rooms with a distance of about 1700 km. Both the network’s multiple sensors and the shields large size significantly enhance the expected dark-photon electromagnetic signals, and long-baseline measurements confidently reduce many local noise sources. Using this network, we constrain the kinetic mixing coefficient of dark photon dark matter over the mass range 4.1 feV-2.1 peV, which represents the most stringent constraints derived from any terrestrial experiments operating over the aforementioned mass range. Our prospect indicates that future data releases may go beyond the astrophysical constraints from the cosmic microwave background and the plasma heating.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Simulated thermonuclear performance of auto-magnetizing helical liner MagLIF target implosions

Magnetized liner inertial fusion (MagLIF) implosions on the Z accelerator require magnetization of the fuel to reduce thermal conduction losses of energy from the laser-preheated deuterium fusion fuel to the surrounding liner material. While external field coils traditionally used to axially magnetize MagLIF targets are limited to 10–20 T (or perhaps ∼ 30 T with technological development), calculations suggest that higher axial magnetic fields would improve thermal insulation of the fuel and improve MagLIF target performance. We present results from three-dimensional radiation-magnetohydrodynamic simulations of MagLIF implosions employing auto-magnetizing helical liners composed of discrete metallic helical conduction paths separated by electrically insulating material. These simulated auto-magnetizing (AutoMag) liners produce axial magnetic fields >30 T inside the fusion fuel prior to implosion. Simulations indicate that higher thermonuclear yields and burn-averaged fuel ion temperatures are attained for implosions using AutoMag liners compared to standard MagLIF implosions. Comparable implosion morphology is evident in synthetic x-ray images of AutoMag–MagLIF and standard MagLIF implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Verifying Deep Reductions in the Nuclear Arsenals: Development and Demonstration of a Motion-detection Subsystem for a “Buddy Tag” Using Non-export Controlled Accelerometers

Future nuclear arms-control agreements may place numerical limits on items that are difficult to monitor with national technical means, even when complemented with onsite inspections. Such items could include small objects and mobile assets, such as non-deployed nuclear warheads and mobile missile launchers. Typically, this verification task can be addressed with unique identifiers, but standard tagging techniques may be unacceptable in this case due to host concerns about safety and intrusiveness. First proposed in the late 1980s and partially developed by Sandia National Laboratories in the early 1990s, the “Proximity Tag” or “Buddy Tag” concept seeks to overcome these concerns by separating the tag from the treaty accountable item itself. A buddy tag has two key elements: a tamper-indicating enclosure and a motion-detection system designed to detect illicit movements in a stand-down period. As part of this project, we have built a buddy-tag prototype for demonstration and evaluation purposes. This paper reviews the design choices and functionalities of the tag’s motion-detection subsystem.We pursue a modular approach for the tag’s hardware, built around an Arduino-class microcontroller and a non-export-controlled low-noise accelerometer, and use open-source algorithms for the motion-detection software. Finally, we discuss the results of an extensive experimental campaign involving both indoor and outdoor measurements assessing the performance of the tag under real-world environmental conditions.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2023

Phase Field Modeling of Corrosion for Design of Next-Generation Magnesium-Aluminum Vehicle Joints

In this study, WPI and its partners sought to understand galvanic corrosion in Mg-Al friction stir weld (FSW) joints. Unlike fusion welds, FSW is done in the solid state. This limits (but does not eliminate) the formation of brittle Al-Mg intermetallics, resulting in better joint strength and corrosion resistance. This study aimed to understand corrosion behavior of Mg-Al FSW joints by using a Cahn-Hilliard phase field electrochemistry model based on the work of Pongsaksawad et al. Its context challenge problem was an ultra-light door designed by Magna with 6061-Al sheet outer and ZEK100-Mg sheet inner panels, joined by an adhesive and FSW. Unlike most FSW joints, which weld through the softer material into the harder one, the Al sheet’s hem joint around Mg required the FSW tool to through the harder Al into the softer Mg, which was itself a challenge. Despite this challenge, PNNL succeeded in consistently making very strong FSW lap joints, by using a triflute tool and power control. Characterization showed mostly separate Al and Mg regions in the weld, usually with a hook protruding from Al into Mg, which likely contributed to high joint strength. Nanohardness mapping showed higher hardness in thin Mg swirls into the Al nugget, likely due to the intermetallics. The study used the industry standard SAE J2334 Cyclic Corrosion Test (CCT) to simulate corrosion conditions over the life of a vehicle, as well as linear polarization testing and ASTM G71 pitting corrosion testing. Corrosion reactions were: H 2 O + ½O 2 + 2e - → 2OH - at the Al cathode, and either Mg → Mg 2+ + 2e - or Mg + 2OH - → Mg(OH) 2 + 2e - at the Mg anode, with electron transfer through the joint. Mass loss increased with Al section length, supporting the hypothesis that galvanic corrosion in Al-Mg joints is limited by the cathodic reaction. Both pitting corrosion (first anode reaction) and hydroxide film formation (second reaction) were observed. The J2334 CCT test method was slightly modified, adding a chromium solution cleaning step after each week of corrosion testing, in order to remove Mg oxides and hydroxides and accurately measure mass loss over time. That said, FSW joints treated in this way did not did not exhibit significant reduction in lap shear strength of the joints vs. newly welded samples which had not undergone corrosion. Corrosion appeared to consist mainly of pitting in Mg in a way which did not directly affect the bond between the materials where the joints failed. A Cahn-Hilliard phase field model coupled with electrical potential described the electronically mediated galvanic corrosion electrochemical reactions described above in the four-component Al-Mg-H 2 O-(H 2 O+½O 2 ) system. This 2-D model successfully predicted Mg(OH)₂ formation at the anode in some circumstances, and Mg pitting corrosion in others, and showed the correct electric field directions in both cases. The model predicted Mg pit corrosion depth within a factor of two of measured pits.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Surface Meteorology at Teller Mile 47 Watershed, Seward Peninsula, Alaska, Ongoing from 2018

Meteorological data are currently being collected at one location at the Teller Mile 47 (TL_MM47) Research Basin Site, Seward Peninsula (N64 58' 36.918", W166 12' 32.67", 67 meters above sea level). The site was installed and initial measurements started in September 2018 and it has operated continuously since then. The meteorological station is co-located with a continuous snow depth sensor and two soil pits for subsurface temperature and moisture measurements. These data are being collected to better understand the energy dynamics above the active layer and permafrost. They complement in-situ snow and soil measurements also at this location. The data could also be used as supporting measurements for other research and modeling activities. There are 35 comma separated value format (*.csv) files provided, where each file contains the full data for an individual parameter (e.g. air temperature at 1.5 meters above the ground surface (teller_m47_air_temperature_150cm_ags_Avg.csv) or soil temperature 20 centimeters below ground surface (teller_m47_dry_soil_pit_temperature_20cmbgs_Avg.csv)) plus the time in Universal Coordinated Time (UTC) and Alaska Standard Time (UTC time minus nine hours). The site was installed and initial measurements started in September 2018. It has been operated continuously since. Primary data gaps are due to battery failure or sensor failure. These data are being collected to better understand the surface energy dynamics above the active layer and permafrost. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a 10-year research effort (2012-2022) to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy?s Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy?s Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Practical considerations for amino acid isotope analysis

Over the last few decades, isotopic analysis of amino acids at the compound- and position-specific levels has been rapidly advancing across diverse fields. As these techniques progress, evaluation of isotopic fractionation associated with sample workup is essential. This critical review of analytical methods through the lens of isotope geochemistry provides a benchmark for researchers across disciplines seeking to make compound- and position-specific amino acid isotope measurements. We focus on preparation, acid hydrolysis, clean-up, derivatization, separation, and C, H, N, and S isotope measurement. Despite substantial customizability across these steps, the following general recommendations should maximize recovery while minimizing isotopic fractionation. Samples should be freeze-dried and stored anoxically at ≤ –20 °C prior to conventional acid hydrolysis (6N HCl, 110 °C, 20–24 h, anoxic), which suffices for many residues. Both gas and liquid chromatographic (GC and LC, respectively) techniques are well-established and separate about 15 amino acids; LC bypasses the need for derivatization, while GC provides higher sensitivity. Furthermore, when derivatization is needed, n-acetyl and alkoxycarbonyl esters provide the most reproducible C isotope ratios. For compound-specific analyses, online GC–IRMS and LC–IRMS systems offer the easiest workflow, but EA–IRMS enables potential multi-element isotope analysis. Emerging techniques like high-resolution mass spectrometry are also promising for multi-element analysis and recover position-specific isotopic information. Looking forward to the next decade of innovation, isotope geochemists and ecologists can improve amino acid isotope analysis by focusing on streamlining multi-element analysis and standardizing calibration practices across laboratories.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

WINDPROF: Merged Best-Estimate Wind Profile Data – Nantucket (WFIP3 Campaign)

WINDPROF provides 10-minute wind and turbulence profiles that integrate scanning Doppler lidars, a profiling lidar, a 915 MHz radar wind profiler, and a sonic anemometer across Northeast U.S. coastal and offshore sites during the WFIP3 campaign. Variables include wind speed, wind direction, vertical velocity, turbulence intensity, and turbulent kinetic energy, each with per-instrument quality control and inter-instrument agreement validation. Profiles are mapped to a standardized height grid – a dedicated near-surface level at the sonic measurement height (5 m AGL), 20 m spacing to 100 m, and 30 m spacing above – and carry component and derived uncertainty estimates. Heights are reported above ground level; the site's ground elevation is stored separately. The Nantucket dataset covers 1 February 2024 – 8 September 2025.

17 WIND ENERGY↗
DOE OSTI2026

WINDPROF: Merged Best-Estimate Wind Profile Data – Block Island (WFIP3 Campaign)

WINDPROF provides 10-minute wind and turbulence profiles that integrate a scanning Doppler lidar, a profiling lidar, a 915 MHz radar wind profiler, and a surface met station across Northeast U.S. coastal and offshore sites during the WFIP3 campaign. Variables include wind speed, wind direction, vertical velocity, turbulence intensity, and turbulent kinetic energy, each with per-instrument quality control and inter-instrument agreement validation. Profiles are mapped to a standardized height grid – a dedicated near-surface level at the 10 m surface-wind height, 20 m spacing to 100 m, and 30 m spacing above – and carry component and derived uncertainty estimates. Heights are reported above ground level; the site's ground elevation is stored separately. The Block Island dataset covers 1 February 2024 – 8 September 2025.

17 WIND ENERGY↗
DOE OSTI2026

WINDPROF: Merged Best-Estimate Wind Profile Data – Rhode Island (WFIP3 Campaign)

WINDPROF provides 10-minute wind and turbulence profiles that integrate a scanning Doppler lidar, a continuous-wave profiling lidar, and a sonic anemometer across Northeast U.S. coastal and offshore sites during the WFIP3 campaign. Variables include wind speed, wind direction, vertical velocity, turbulence intensity, and turbulent kinetic energy, each with per-instrument quality control and inter-instrument agreement validation. Profiles are mapped to a standardized height grid – a dedicated near-surface level at the sonic measurement height (4 m AGL), 20 m spacing to 100 m, and 30 m spacing above – and carry component and derived uncertainty estimates. Heights are reported above ground level; the site's ground elevation is stored separately. The Rhode Island dataset covers 7 February 2024 – 4 September 2025.

17 WIND ENERGY↗
DOE OSTI2020

Jet substructure from dark sector showers

We examine the robustness of collider phenomenology predictions for a dark sector scenario with QCD-like properties. Pair production of dark quarks at the LHC can result in a wide variety of signatures, depending on the details of the new physics model. A particularly challenging signal results when prompt production induces a parton shower that yields a high multiplicity of collimated dark hadrons with subsequent decays to Standard Model hadrons. The final states contain jets whose substructure encodes their non-QCD origin. This is a relatively subtle signature of strongly coupled beyond the Standard Model dynamics, and thus it is crucial that analyses incorporate systematic errors to account for the approximations that are being made when modeling the signal. We estimate theoretical uncertainties for a canonical substructure observable designed to be sensitive to the gauge structure of the underlying object, the two-point energy correlator $ {e}_2^{\left(\beta \right)} $ , by computing envelopes between resummed analytic distributions and numerical results from Pythia. We explore the separability against the QCD background as the confinement scale, number of colors, number of flavors, and dark quark masses are varied. Additionally, we investigate the uncertainties inherent to modeling dark sector hadronization. Simple estimates are provided that quantify one’s ability to distinguish these dark sector jets from the overwhelming QCD background. Such a search would benefit from theory advances to improve the predictions, and the increase in statistics using the data to be collected at the high luminosity LHC.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Validation of Robustness in TCR Design Strategies

Advanced Manufacturing (AM) has been identified as one of key pathways in accelerating deployment of next generation of nuclear power plants. The nuclear industry continues to predominately rely on fabrication techniques and materials that their codes and standards were approved decades ago. This legacy approach in the highly regulated nuclear sector has brought uncertainty to commercial viability of nuclear energy in the U.S. The Transformational Challenge Reactor (TCR), sought to utilize AM methods for fabrication of a High Temperature Gas Reactor (HTGR). The program sought to leverage AM to construct a non-conventional geometry made up of TRISO fuel and hydride moderator in SiC matrix. This project objective was to provide independent analysis of the core configuration with separate set of tools and approaches than utilized by the TCR team in a 2-year time frame. This NEUP project also tackled a question: Can AM be a cost-effective tool in changing the commercial paradigm of nuclear. We investigated this question in-context of a micro HTGR. While respecting the inherit uncertainty in our input parameters, overall we saw that AM has potential in improving economic competitiveness of nuclear energy when employed on multiple fronts (i.e. few percentage cost improvement per component). Given realizing AM requires mass orders and large R&D investment for commercial utilization, Department of Energy should focus its support on few key enabling technologies and support their codes and standards development and qualification cost (including irradiation as applicable) rather than taking a diluted approach.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Leafweb: Leaf Gas Exchange and Pulse-Amplitude Modulated Fluorometry for C4 Species, June 2026 Release

This dataset contains leaf gas exchange and Pulse-Amplitude Modulated (PAM) fluorometry for 98 C4 species. The C4 photosynthetic pathway employs specialized CO2 concentration mechanisms and Kranz anatomy to enrich CO2 concentration around Rubisco, the enzyme that catalyzes carbon fixation in the Calvin-Benson cycle to suppress photorespiration and increase the use efficiencies of light, nitrogen, and water as compared to the C3 photosynthetic pathways. Large-scale C4 photosynthetic datasets are relatively scarce, which has affected C4 photosynthesis research. To improve C4 photosynthetic data availability, Leafweb organized an effort to systematically collect, compile, standardize, and organize measurements of leaf gas exchange and/or Pulse-Amplitude Modulated (PAM) fluorometry of C4 species. This derived a C4 photosynthetic dataset containing measurements made by independent researchers in multiple countries in various environments (field, garden, or greenhouse). It covers three biochemical subtypes – the nicotinamide adenine dinucleotide phosphate-malic enzyme (NADP-ME), nicotinamide adenine dinucleotide-malic enzyme (NAD-ME), and phosphoenolpyruvate carboxykinase (PEP-CK) subtypes. This dataset is useful for using Artificial Intelligence / Machine Learning and mechanistic models to study C4 photosynthesis and compare across different biochemical subtypes. This dataset contains 3 compressed (*.zip) folders containing 1,892 data files in comma-separate values (*.csv) format. Additional metadata are provided: one data dictionary and a file-level metadata file in comma-separate values (*.csv) format and a user guide in PDF (*.pdf) format.

Zhou, Haoran [Tianjin University, China]↗
DOE OSTI2024

Distinct Mechanism of Anti-Corrosion and Swelling-Adhesion Modeling of Low-Dimensional Nylon-Fluoropolymer Composite Coatings

Compared to other polymers, composite coatings with fluoropolymers as the matrix have attracted considerable interest due to their mechanical performance, chemical stability, and low surface energy. Herein, we present an anticorrosion mechanism of fluoropolymer composite coatings achieved by dispersing varying amounts of polyamide 12 (PA-12) particles over a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) matrix. The choice of PVDF-HFP as a coating matrix was driven by its superior processability and mechanical properties over Teflon, while PA-12 afforded swelling capacity, preventing electrolyte permeation, and inhibiting matrix stress crack propagation. The corrosion resistance of the coatings was assessed mainly by potentiodynamic polarization and impedance measurements while being immersed in a NaCl solution. Our electrochemical measurement findings showed that 0.75% w/w PA-12 in the PVDF-HFP matrix significantly enhanced corrosion protection even after 21 days of immersion. Microscopy, dielectric spectroscopy, surface analysis, and mechanical testing (American Society for Testing and Materials standards) corroborated the results. PVDF-HFP coatings containing a minimum percolation threshold of 0.75 wt % PA-12 with 1 mil thickness on mild steel exhibited a remarkable increase in resistance and film adhesion, and a notable corrosion rate decrease. Finite element analysis simulation with a bilinear traction-separation law confirmed the swelling mechanism and adhesion behavior. Finally, this study highlights the potential of nylon particle dispersion in PVDF-HFP matrices as a practical approach to developing advanced anticorrosion coatings with promising practical applications in various industries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

1994 Treasure Coast Travel Characteristics Study

The Treasure Coast Travel Characteristics Study was initiated in January 1995 in order to improve the travel forecasting accuracy of the Florida Standard Urban Transportation Model System for this area. The main objective of the surveys was to establish the socioeconomic and travel characteristics of the Treasure Coast Area of Mart, St. Lucie, and Indian River Counties. A total of 1,531 households participated in the study. The household study was separated into multiple parts: one used phone interviews to collect data and another provided travel logs for study participants to fill out, ranging from one- to three-day logs.

1Hz data↗