Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

IACMI Project 4.7: Pultruded Textile Carbon Fiber for Spar Caps (Final Report)

The primary objective of this project was to demonstrate the potential to significantly reduce the cost of wind turbine blades with carbon fiber reinforced polymer (CFRP) structure. Applicability of textile carbon fibers (TCF) were evaluated for use in pultruded spar cap (SC) elements as a path to cost reduction for utility scale wind turbine blades. In earlier work for the Department of Energy (DOE) Wind Energy Technologies Office (WETO), a collaboration of Sandia National Laboratory (SNL), Oak Ridge National Laboratory (ORNL), and Montana State University has demonstrated potential for pultruded TCF to compete with infused fiberglass and commercially available carbon fiber pultruded sections for spar cap construction. In the design cases evaluated, the TCF sections fared well when compared on cost per unit composite stiffness and cost per unit composite compressive strength for those designs [1]. Both stiffness and compressive strength tend to be key factors in the design of blade composite Spar Cap which carry the bulk of the blade structural loads in bending. Spar Cap design tends to distribute largely symmetric tensile and compressive stresses to opposite sides of the spar structure, but since carbon fiber composite compressive strength is typically 20-50% lower than tensile strength, the compressive loading reaches failure levels well before the tensile loading. Stiffness is critical in containing the large tip deflection in high wind loading situations. However, materials and process development were very limited in the earlier study and the work in this project was expanded to make the comparative information more representative of what will be required in order to make further inroads towards implementation. Similar to that study, this project team confirmed that the primary materials of interest for pultruded spar cap elements should be thermoset (TS) resins reinforced by carbon fibers, utilizing as high a percentage of TCF as practical to benchmark cost and performance against commercial carbon fibers. To make the closest comparison possible and eliminate specific test article size, resin selection, and equipment/operational nuance effects, the team planned to pultrude sections with 100% commercially available carbon fiber (Panex 35 carbon fiber from Zoltek) as well as samples utilizing high fractions of TCF. The resin system chosen was based on formulations recommended by large wind industry supplier Hexion and consisted of Hexion resin RSL-4597, curing agent CCA-138, and internal mold release additive 117, along with common kaolin filler ASP400P from BASF. As commonly deployed in spar cap configurations, the team had a mold built to pultrude a rectangular spar cap element of 100mm width and 3mm thickness. The extremely limited number of samples produced for the earlier study were produced with a “generic” epoxy utilized for a variety of applications by the pultruder contracted to produce test articles for demonstration purposes. More importantly, those samples were produced at a fiber fraction only slightly over 50%. Based on feedback from our industrial advisory team for that project and strongly recommended by this project team, the consensus is that it is highly desirable to obtain fiber fractions of 65-68% for significant penetration in wind blade spar cap. Although this requirement has yet to be exhaustively confirmed in readily available information, this was established as a project goal and informally decided we needed to exceed 60% fiber fraction to gain serious industry consideration. Previous TCF pultrusion trials have been challenged by the lack of robust TCF packages, resulting in non-uniform tension across and between tows, as well as excess labor and waste for removal of interleaved paper. The non-uniform tension and associated intermingling of tows in textile acrylic fiber tows and associated difficulties created from broken filaments in carbon fiber conversion inhibit the ordered packing necessary to enhance fiber fraction elevation. (These “cross-overs” are not considered undesirable for textile applications and there is some sense that they might be advantageous for those applications). In addition to work that is ongoing at the acrylic fiber manufacturers to improve their formats, The Institute of Advanced Composites Manufacturing Innovation (IACMI) Project 6.12 (report PA16-0349-6.12-01) [2] has developed and demonstrated a more robust packaging and creeling approach that at least partially addresses these issues, thus improving control of the TCF feed into the pultrusion unit. It was hoped that these and other improvements currently being implemented would allow us to achieve fiber fractions at least approaching these fiber fraction targets. During this project, sections utilizing 100% commercially available carbon fiber reinforcement were produced as a baseline, as well as sections reinforced with about 94% TCF and the balance being commercially available fiber for comparison. The most important finding was that similar to results reported in the earlier WETO-funded project and results from tests of TCF reported at IACMI meetings, this work demonstrated that sections pultruded with TCF in an epoxy resin frequently utilized in actual spar cap production had stiffness and compressive strengths largely comparable to similar sections pultruded with a commercially available carbon fiber also frequently utilized in the wind industry. Although the amount of that data is limited, some of the tensile strength results were actually closer than would have been expected based on fiber strength results provided by the TCF and commercial fiber producers. The actual test data are reported and discussed in detail in Section 5. The pultruded sections dominated by TCF reinforcement were approximately 8-10% lower in fiber fraction than for the sections produced using commercial fiber alone, making direct comparison difficult. The COVID-19 project has provided significant insight into the current state-of-the-art with various TCF product forms. The data obtained in this project will guide the planned improvements at the precursor level, especially in attaining uniform tensioning and payout to facilitate enhanced fiber fractions and overall processability of the TCF composites. The project team is providing guidance to stakeholders concerning the attributes, needs, and potential demand for TCF in wind blade spar caps. Results achieved in this project are consistent with findings in the related work cited [1] and support this guidance and the high potential for this product type. TCF precursor-producing partners continue to express interest in enhancing their product forms and the team looks forward to working with these improved materials as they become available.

42 ENGINEERING↗
DOE OSTI2026

Neutron Diffraction Residual Stress Characterization of Large-Scale Components by WA-DED

Two large scale 316L stainless steel cylindrical shells were fabricated by wire arc directed energy deposition (WA DED). Residual stresses were measured by neutron diffraction, and the microstructure and mechanical properties of the printed material were characterized. Longitudinal and transverse residual stresses were compressive at the inner diameter, near neutral at mid wall, and tensile at the outer diameter; radial (through thickness) residual stresses were relatively low in magnitude, and peak tensile residual stresses occurred at the outer diameter surface along the longitudinal direction. The printed 316L SS exhibited a heterogeneous microstructure with finely dispersed δ ferrite, and demonstrated high yield and tensile strengths with large elongation and ductile fracture at ambient temperature and at 250 °C. These results indicate that the outer diameter surface and near surface regions—where tensile residual stress is highest—are the most vulnerable to residual stress–sensitive failure modes, such as stress corrosion cracking and fatigue.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Draft ASME Code Case to qualify L-PBF 316H material for Section III, Division 5 applications

This report documents the AMMT program’s development and submission of a draft ASME Code Case to qualify Laser Powder Bed Fusion (L PBF) Type 316H stainless steel for Section III, Divi-sion 5 Class A and SM high temperature nuclear applications. It summarizes the technical basis, the comprehensive high temperature mechanical test database assembled between 2023–2026, and the proposed code language and qualification framework submitted to ASME. The work was co-ordinated across multiple national laboratories and leverages prior ASME efforts to integrate additive manufacturing into the Boiler & Pressure Vessel Code. The body of the report describes the experimental database and analysis supporting the Code Case: tensile, creep, fatigue, creep fatigue, and thermal aging tests collected from multiple additive manufacturing sites, machine types, and powder lots, with material processed by a solution anneal heat treatment. The dataset — including both full size and subsized specimens and tests oriented parallel and perpendicular to build direction — shows limited tensile anisotropy, tensile properties comparable to wrought 316H, creep strength within the scatter of wrought material, but markedly reduced creep ductility above about 650 °C associated with rapid σ phase formation in L PBF microstructures. The draft Code Case itself prescribes a staged qualification model (manufacturing process qualification, component qualification, and per build witness testing), treats L PBF components as equivalent to Type 316 weld metal for design and inspection, and requires mechanical, chemical, and metallographic controls tied to ASTM/ISO 52946. Key acceptance criteria include tensile tests within a 90% prediction interval of the AMMT dataset, a creep fatigue screening test adapted from ASME Section III, Division 5, Subsection HB, HBB 2800 but with the cycle acceptance reduced to 100 for L PBF material, and double volumetric inspection of production components. The report concludes that the present data support treating L PBF 316H as analogous to conventional fusion weld metal for Division 5 design and inspection, while highlighting important caveats: the σ phase driven loss of creep ductility above ~650 °C, preliminary indications of enhanced creep fatigue sensitivity in some lots, and remaining gaps in long term aging and additional cyclic testing. Recommended next actions include completing outstanding cyclic and long duration creep/aging tests on the solution annealed condition, supporting inclusion of the 316H chemistry and heat treatment in ASTM/ISO 52946, and continuing engagement with ASME and NRC during balloting and review to enable industry adoption.

Messner, Mark C. (ORCID:0000000200404385)↗
DOE OSTI2024

Flax–Reinforced Vitrimer Epoxy Composites Produced via RTM

Composite laminates were produced by RTM using similar glass and flax fabrics and both vitrimer epoxy and aerospace-grade epoxy, both formulated for liquid molding. Tensile and flexural properties were measured and compared, revealing that the vitrimer composites exhibited equivalent performance in flexural strength and tensile modulus, but slightly lower performance in tensile strength relative to reference epoxy composites. In general, glass–fiber composites outperformed flax–fiber composites in tension. However, both glass and flax–fiber composites yielded roughly equivalent flexural strength and tensile modulus-to-weight ratios. Flax fabrics were recovered from composites by matrix dissolution, and a second-life laminate showed full retention of the mechanical properties relative to those produced from fresh flax. Finally, a demonstration of re-forming was undertaken, showing that simple press-forming can be used to modify the composite shape. However, re-forming to a flat configuration resulted in local fiber damage and a decrease in mechanical properties. An alternative forming method was demonstrated that resulted in less fiber damage, indicating that further refinements might lead to a viable forming and re-forming process.

Martinez, Patricio (ORCID:0000000225884389)↗
DOE OSTI2021

External-Field-Induced Phase Transformation and Associated Properties in a Ni 50 Mn 34 Fe 3 In 13 Metamagnetic Shape Memory Wire

Metamagnetic shape memory alloys exhibit a series of intriguing multifunctional properties and have great potential for applications in magnetic actuation, sensing and magnetic refrigeration. However, the poor mechanical properties of these alloys with hardly any tensile deformability seriously limit their practical application. In the present work, we developed a Ni-Fe-Mn-In microwire that exhibits both a giant, tensile superelasticity and a magnetic-field-induced first-order phase transformation. The recoverable strain of superelasticity is more than 20% in the temperature range of 233–283 K, which is the highest recoverable strain reported heretofore in Ni-Mn-based shape memory alloys (SMAs). Moreover, the present microwire exhibits a large shape memory effect with a recoverable strain of up to 13.9% under the constant tensile stress of 225 MPa. As a result of the magnetic-field-induced first-order phase transformation, a large reversible magnetocaloric effect with an isothermal entropy change ΔS m of 15.1 J kg –1 K –1 for a field change from 0.2 T to 5 T was achieved in this microwire. The realization of both magnetic-field and tensile-stress-induced transformations confers on this microwire great potential for application in miniature multi-functional devices and provides an opportunity for multi-functional property optimization under coupled multiple fields.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In Situ Synchrotron X-ray Micro-Diffraction Investigation of Elastic Strains in Laminated Ti-Al Composites

Spatially resolved elastic strains in the bulk interior of a laminated Ti-Al metal composite were studied during in situ tensile loading at strains up to 1.66% by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM). For both Al and Ti grains, deviatoric elastic strains were estimated based on polychromatic X-ray microbeam diffraction, while lattice strains along the normal direction of the tensile sample were directly measured using monochromatic X-ray microbeam diffraction. The estimated deviatoric strains show large spatial variations, and the mean values are consistent with the external loading conditions, i.e., increasing tensile strain along the tensile direction and increasing compressive strain along the sample normal with increasing loading. The directly measured lattice strains also show large spatial variations, although the magnitude of this variation is smaller than that for the estimated deviatoric strain. The directly measured lattice strains in Ti grains are largely consistent with the external loading, whereas those in Al grains are in contradiction with the external loading. The causes of the experimental results are discussed and related to both the laminated microstructure of the composite material and the limitations of the techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion

The present work correlates the quasi-static, tensile mechanical properties of additively manufactured Ti-6Al-4V extra low interstitial (ELI, Grade 23) alloy to the phase constituents, microstructure, and fracture surface characteristics that changed with post-heat treatment of stress relief (670 °C for 5 h) and hot isostatic pressing (HIP with 100 MPa at 920 °C for 2 h under an Ar atmosphere). Ti-6Al-4V ELI alloy tensile specimens in both the horizontal (i.e., X and Y) and vertical (Z) directions were produced by the laser powder bed fusion (LPBF) technique. Higher yield strength (1141 MPa), higher tensile strength (1190 MPa), but lower elongation at fracture (6.9%), along with mechanical anisotropy were observed for as-stress-relieved (ASR) samples. However, after HIP, consistent and isotropic mechanical behaviors were observed with a slight reduction in yield strength (928 MPa) and tensile strength (1003 MPa), but with a significant improvement in elongation at fracture (16.1%). Phase constituents of acicular α' phase in ASR and lamellar α + β phases in HIP samples were observed and quantified to corroborate the reduction in strength and increase in ductility. The anisotropic variation in elongation at fracture observed for the ASR samples, particularly built in the build (Z) direction, was related to the presence of “keyhole” porosity.

42 ENGINEERING↗
DOE OSTI2022

Benchmarking a 9Cr-2WVTa Reduced Activation Ferritic Martensitic Steel Fabricated via Additive Manufacturing

Reduced activation ferritic (RAF) martensitic steels are promising candidates for the first wall of fusion reactors. However, current manufacturing capabilities call for these components to be made by welding wrought plates. This limits design freedom and necessitates the use of post-weld heat treatments (PWHT) in accordance with the boiler and pressure vessel code. Additive manufacturing (AM) can offer a unique solution to solve this challenge by leveraging the layer-wise deposition strategy to come up with temper bead deposition techniques to eliminate post-processing heat treatments (PPHT). However, it is necessary to benchmark the properties of RAF steels fabricated by AM with their wrought counterparts to identify the process-structure-property correlation, which is the goal of this study. The study demonstrates that while tensile properties at room temperature and high temperatures are satisfactory, the as fabricated and samples after PPHT have significant heterogeneity in tensile elongation. This has been attributed to the presence of discontinuities in the build. The as-fabricated samples have an average tensile strength of 1190 + 12 MPa and an average elongation of 15 + 5% at room temperature and 658 ± 20 MPa ultimate tensile strength (UTS) and 14 ± 7% at 600 °C. After the post-weld heat treatment, mechanical properties decrease to around 600–650 MPa and an elongation between 20–25% at room temperature to 300 MPa UTS and 25–28% elongation at 600 °C. The characterization of microstructures at various length scales demonstrates that the as-fabricated structure has a significant fraction of delta ferrite in a lath martensitic matrix. No precipitates could be identified in the as-fabricated structure. PPHT led to a decrease in the area fraction of delta ferrite and precipitation of M 23 C 6 and MX. Detailed characterization clearly demonstrates that the lack of precipitates in the as-fabricated structure could be due to the slow tempering response of the alloy. Finally, the needs to develop new alloys to achieve the objectives stated above are articulated.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enabling Industrial Re-Use of Large-Format Additive Manufacturing Molding and Tooling

Large-format additive manufacturing (LFAM) is an enabling manufacturing technology capable of producing large parts with highly complex geometries for a wide variety of applications, including automotive, infrastructure/construction, and aerospace mold and tooling. In the past decade, the LFAM industry has seen widespread use of bio-based, glass, and/or carbon fiber reinforced thermoplastic composites which, when printed, serve as a lower-cost alternative to metallic parts. One of the highest-volume materials utilized by the industry is carbon fiber (CF)-filled polycarbonate (PC), which in out-of-autoclave applications can achieve comparable mechanical performance to metal at a significantly lower cost. Previous work has shown that if this material is recovered at various points throughout the manufacturing process for both the lab and pilot scale, it can be mechanically recycled with minimal impacts on the functional performance and printability of the material while significantly reducing the feedstock costs. End-of-life (EOL) CF-PC components were processed through industrial shredding, melt compounding, and LFAM equipment, followed by evaluation of the second-life material properties. Experimental assessments included quantitative analysis of fiber length attrition, polymer molecular weight degradation using gel permeation chromatography (GPC), density changes via pycnometry, thermal performance using dynamic mechanical analysis (DMA), and mechanical performance (tensile properties) in both the X- and Z-directions. Results demonstrated a 24.6% reduction in average fiber length compared to virgin prints, accompanied by a 21% decrease in X-direction tensile strength and a 39% reduction in tensile modulus. Despite these reductions, Z-direction tensile modulus improved by 4%, density increased by 6.8%, and heat deflection temperature (HDT) under high stress retained over 97% of its original value. These findings underscore the potential for integrating mechanically recycled CF-PC into industrial LFAM applications while highlighting the need for technological innovations to mitigate fiber degradation and enhance material performance for broader adoption. This critical step toward circular material practices in LFAM offers a pathway to reducing feedstock costs and environmental impact while maintaining functional performance in industrial applications.

additive manufacturing↗
DOE OSTI2020

Radiation Damage Studies on Titanium Alloys as High Intensity Proton Accelerator Beam Window Materials

A high-strength dual a+ß phase titanium alloy Ti–6Al–4V is utilized as a material for beam windows in several accelerator target facilities. However, relatively little is known about how material properties of this alloy are affected by high-intensity proton beam irradiation. With plans to upgrade neutrino facilities at J-PARC and Fermilab to over 1 MW beam power, the radiation damage in the window material will reach a few displacements per atom (dpa) per year, significantly above the ~0.3 dpa level of existing data. The international RaDIATE collaboration, Radiation Damage In Accelerator Target Environments, has conducted a high intensity proton beam irradiation of various target and window material specimens at Brookhaven Linac Isotope Producer (BLIP) facility, including a variety of titanium alloys. Post-Irradiation Examination (PIE) of the specimens in the 1st capsule, irradiated at up to 0.25 dpa, is in progress. Tensile tests in a hot cell at Pacific Northwest National Laboratory (PNNL) exhibited a clear signature of radiation hardening and loss of ductility for Ti–6Al–4V, while Ti–3Al–2.5V, with less ß phase, exhibited less severe hardening. Microstructural investigations will follow to study the cause of the difference in tensile behavior between these alloys. High-cycle fatigue (HCF) performance is critical to the lifetime estimation of beam windows exposed to a periodic thermal stress from a pulsed proton beam. The first HCF data on irradiated titanium alloys are to be obtained by a conventional bend fatigue test at Fermilab and by an ultrasonic mesoscale fatigue test at Culham Laboratory. Specimens in the 2nd capsule, irradiated at up to ~1 dpa, cover typical titanium alloy grades, including possible radiation-resistant candidates. These systematic studies on the effects of radiation damage of titanium alloy materials are intended to enable us not only to predict realistic lifetimes of current beam windows made of Ti–6Al–4V, but also to extend the lifetime by choosing a more radiation and thermal shock tolerant alloy with a preferable heat treatment, or even by developing new materials.

Titanium Alloy, Beam Window, Proton Beam, Radiatio↗
DOE OSTI2025

The Ductility of 49Fe-49Co-2V Soft Magnetic Alloy Bar: Surface Effects and Test Methods

The tensile ductility of 49Fe-49Co-2V (Hiperco® 50A) bar was investigated in both as-received and heat-treated conditions. The as-received/machined specimens exhibit very low ductility compared to samples where heat treatment was the final step prior to testing. Microstructural characterization showed that internal residual strain from bar processing and, most importantly, surface machining damage, cause lower elongation in the as-received material. Because fracture of this intermetallic alloy initiates at the surface, it is particularly susceptible to surface machining damage, i.e., the near-surface region has already exhausted most of its ability to accumulate tensile strain. During heat treatment, the internal residual strain and near-surface machining damage are eliminated and ductility is improved, despite a higher degree of crystallographic ordering in the heat-treated condition (which typically lowers ductility). Furthermore, if machining is again performed after heat treatment, the material again exhibits brittle behavior, even with only light touch-up machining passes. Here, in this work, methods of tensile strain measurement were investigated, namely conventional knife-edge extensometry and noncontact digital image correlation (DIC) on heat-treated material. For clip-on knife-edge extensometry, the range of failure strain was 2.5-5.5% for heat-treated Hiperco. For noncontact methods, ductility up to 7% was observed. The results highlight the tendency for the alloy to fail at surface imperfections, even those produced by application of the extensometer itself. Noncontact laser extensometry is recommended for determining the intrinsic ductility of the alloy. A method of laser surface modification was developed which increased ductility by ~ 100% compared to unmodified samples. The high cooling rates achieved during laser surface processing can bypass the ordering reaction and produce a ductile disordered structure at the surface that exhibits ductile fracture characteristics.

EBSD↗
DOE OSTI2022

Powder Metallurgy HIP Process Study and Mechanical Property Evaluations for IN740H

The effects of hot isostatic pressing (HIP) parameters and powder size distribution (PSD) on the resulting microstructure and properties of powder metallurgy (P/M) IN740H have been investigated. Properties can be substantially tailored through the appropriate management of these parameters. Applying a thermal presoak to the input powder prior to the sintering stage of HIP can significantly increase average grain size and coarse grain fraction, enabling a trade for improved creep resistance at the expense of tensile strength. Here, powder thermal presoak was found to have a larger impact on microstructure and properties than the use of a coarser PSD alone. Additionally, substantial grain growth and grain boundary migration is observed in P/M IN740H at HIP temperatures above 1260°C. Given its inherently finer grain size, P/M HIP IN740H typically outperforms its cast and wrought counterparts in tensile response. Creep life at 700–800°C was inferior to wrought due to PPBs coincident with grain boundaries which served as cavity nucleation sites, leading to lower creep ductility. The ability to adjust the microstructure toward a more balanced creep and tensile behavior allows P/M HIP IN740H to be considered for high-temperature applications in advanced ultra-supercritical steam and supercritical carbon dioxide power cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental Evaluation of Interfacial Bonding Strength Between 304 Stainless Steel Substrate and Electrodeposited Nickel Coating Using Mesoscale Mechanical Testing Methods

Electrodeposition is a commonly used method for depositing a metal layer on a metallic substrate, to provide a decorative finish or for functional purposes including wear and corrosion resistance. The interfacial bonding strength is a critical factor in determining the quality of electrodeposition, as it ensures the adhesion of the deposited layer to the substrate. Despite its importance, there has not previously been a suitable mechanical testing method to quantitatively characterize the bonding strength between the electrodeposited layers and the substrate, due to the high strength of the materials and to restrictions imposed by the geometry (due to the small thickness of the plating layer) to manufacture tensile bars. In this study, we introduce a novel mesoscale mechanical testing method to overcome these limitations. This technique was applied to assess the bonding strength between a 304 stainless steel (SS) substrate and electrodeposited nickel with three different plating formulae (nickel sulfamate, Watts bath, and hard nickel). The thickness of the pure nickel coatings achieved for each of the three electrolyte solutions was approximately 1 mm on each side of the substrate. Mesoscale tensile bars of 1 mm length were manufactured by a femtosecond laser, with the material interface at the center of the gauge section, and then tensile-tested with digital image correlation. Further, the results proved that the electrodeposition technique is able to produce a very high bonding strength that is close to the yield strength of both the substrate material and the electrodeposited nickel layer. Additionally, in the case of the Watts bath formula, the interfacial bonding strength between the SS 304 and electrodeposited nickel can exceed that of the nickel layer. This method is expected to be useful for quantifying the interfacial bonding strength in numerous applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Using post-processing heat treatments to elucidate precipitate strengthening of additively manufactured superalloy 718

The poor machinability and extensive work hardening of Ni-based superalloys makes additive manufacturing an attractive option for producing geometrically complex components with distinct microstructures. Although previous studies show recovery of high strength at room temperature, very few studies demonstrate successful properties at elevated temperatures required for industrial applications. Here, the objectives of this study are to present a post-build heat treatment for high strength across a wide temperature range, determine the strength contribution of nanoscale precipitating phases to the overall mechanical properties of superalloy 718, and from these, provide a comprehensive microstructure-property relationship for wrought and AM 718 to guide efforts to simulate the properties of AM components. Laser powder bed fusion–produced superalloy 718 was characterized at multiple length scales using scanning electron microscopy and transmission electron microscopy in the as-built condition and with multiple heat treatments designed to form combinations of γ', γ", and δ precipitates. Uniaxial tensile tests performed from room temperature to 600 °C on subsize specimens determined the yield strength, elastic modulus, ultimate tensile strength, fracture stress, and uniform elongation. Precipitates in this work proved to be weak barriers to dislocation motion through a dispersed barrier model, but they provided strength to the alloy through their consistent high density. The relative contribution to the yield strength from γ" remained consistent between 48% and 57% of the total strength up to 600 °C, the primary influence on the high temperature strength of superalloy 718. The strength factors for γ" and δ precipitates were found to trend inversely with tensile test temperature and may be attributable to the differences in precipitate coherency. A post-build heat treatment is recommended to maintain high strength at elevated temperatures. A quantitative microstructure-property relationship, dependent on precipitate size, density, and morphology, was derived and can estimate the yield strength across a wide temperature range applicable to the operational regimes for superalloy 718.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impact of droplet oxidation on mechanical properties of an Al-7Si-0.4Mg alloy fabricated with liquid metal jetting

Droplet-on-demand liquid metal jetting (DOD-LMJ) is a new method for additive manufacturing of bulk structural alloys. Here, we report on the microstructure, tensile, and fatigue properties of an Al-7Si-0.4Mg (A356) alloy fabricated with LMJ. Liquid metal droplets were shielded by high-purity Ar gas shroud during deposition. Atom probe tomography revealed that a few nanometers thick (Al-Mg-Si)-O oxide film formed on the droplets despite Ar gas shielding. Tensile tests on peak-aged LMJ A356 alloy showed that yield strength was isotropic (250 MPa), but ductility was lower in the build direction (6.1 ± 1.4 %) compared to the transverse direction (9.4 ± 1.0 %). Lower ductility in the build direction was attributed to delamination of metal-oxide interfaces at layer boundaries. The ductility and yield strength of LMJ A356 were similar to cast A356 and laser powder bed fused (LPBF) A357 alloys, indicating the limited impact of oxide film on tensile properties. The oxide film severely impacted the fatigue properties. Fatigue resistance of LMJ A356 was limited by fatigue crack initiation at lack-of-fusion defects and fatigue crack propagation along layer boundaries by delamination of the metal-oxide interface. The fatigue strength of LMJ A356 at 60 MPa was lower than cast A356 and LPBF A357 alloys in the peak-aged condition. This research underscores the need for managing droplet oxidation during LMJ additive manufacturing of structural alloys.

42 ENGINEERING↗
DOE OSTI2021

Seawater sea-sand engineered/strain-hardening cementitious composites (ECC/SHCC): Assessment and modeling of crack characteristics

Highlights: • A probabilistic model was proposed to model the crack width evolution of SS-ECC at different strain levels. • The Weibull distribution fit the crack width distribution better than the log-normal distribution. • A 5-D representation was proposed to assess the SS-ECC by considering both cracking and mechanical performance. • Larger sea-sand size and lower fiber dosage led to larger crack widths in SS-ECC under the same tensile strain. • 18-mm PE fiber led to larger crack widths in SS-ECC at strain >2%, due to a large fraction of fiber rupture. Seawater sea-sand Engineered Cementitious Composites (SS-ECC) is a new version of ECC for marine constructions facing the scarcity of freshwater and river/manufactured sand. This study aims to assess and model the crack characteristics of SS-ECC, which are critical for its applications with non-corrosive reinforcements. The influence of sea-sand size, fiber length and fiber dosage on the crack characteristics of SS-ECC was explored. A five-dimensional representation was proposed to assess the overall performance of SS-ECC, by comprehensively considering both the crack characteristics (i.e., crack width and its variation) and the mechanical properties (i.e., compressive and tensile properties). A probabilistic model was also proposed to describe the stochastic nature and evolution of crack width, and it can be used to estimate the critical tensile strain on SS-ECC for a given crack-width limit and cumulative probability. The findings and proposed methods can facilitate the design of SS-ECC in marine and coastal structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Synergistic cellulase–xylanase formulations for enhanced dewatering and fiber bonding toward energy-efficient and sustainable paper and packaging production

A mechanistic understanding of the synergistic effects of enzymes on cellulosic fibers dewatering and fiber bonding is essential for advancing energy-efficiency and lightweight production of paper and packaging materials. This study investigates the impact of varying cellulase and xylanase formulations on equilibrium moisture content (EMC) after pressing and tensile strength of cellulosic fiber webs using a factorial experimental design. Nine custom enzyme formulations were evaluated at controlled dosages ranging from ∼20 to 76 FPU/mL cellulase and ∼500–1130 IU/mL xylanase. Response surface modeling revealed a significant synergy, particularly at 20–40 FPU/mL cellulase combined with ≥ 1000 IU/mL xylanase. Under these conditions, EMC decreased by up to 3.6% compared with the untreated refined control, while tensile index gains of up to 16% were statistically significant for optimized blends (p < 0.05). The interaction between cellulase and xylanase was also significant for the tensile response (p = 0.010). Protein efficiency analysis showed that optimized formulations containing 30–40% less protein outperformed the commercial benchmark. The nonlinear synergy between cellulase and xylanase is attributed to their complementary substrate specificities. Endoglucanase- and β‑glucosidase‑rich cellulases hydrolyze internal β‑1,4‑glycosidic bonds in amorphous cellulose, loosening fiber walls and increasing flexibility, while xylanases target hemicellulose, primarily xylan-rich domains, enhancing porosity and improve cellulase accessibility. Tailoring enzyme formulations at low loadings overcomes traditional trade-offs between strength and dewatering, enabling cost-effective, energy-efficient, low-carbon solutions for sustainable packaging and hygiene products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗