SEARCH · Search NASA

Results for “conversion coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

DOE OSTI2025

FCET Solid Oxide Fuel Cell Testing and Development (CRADA 526) (Final Report)

Pacific Northwest National Laboratory (PNNL) tested electrolyte coatings from Fuel Cell Enabling Technologies, Inc. (FCET) for use in solid oxide fuel cells (SOFCs). The key technology held by FCET is a process to deposit thin layers of oxide materials, less than 1 μm in thickness. The range of possible materials that can be deposited with their method is broad, but this project focused on the gadolinium-doped ceria (GDC) and yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight electrolyte membranes have been a long-sought target in SOFC research. The thinner the electrolyte, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). A YSZ thickness of 1 μm would be a step change from the state-of-the-art, tape-cast electrolytes (~10 μm). An in-house prototype SOFC stack from FCET was first tested. The sealing geometry of the prototype stack was determined to be problematic, and testing shifted to button cells. Anode-supported solid oxide electrolysis cell (SOEC) button cells without an electrolyte layer were produced at PNNL and sent to FCET for coating with electrolyte. Three cells were tested with a gadolinium-doped ceria (GDC) electrolyte applied via spin coating. GDC was chosen for its conductivity at lower temperatures than YSZ. All three cells failed during initial reduction under hydrogen at 600°C. Testing then shifted to YSZ, which is the standard SOFC electrolyte. Several button cells were coated with YSZ and examined with scanning electron microscopy (SEM). A promising coating of ~1 mm thickness was observed under SEM. A similarly coated button cell was tested and failed similarly to previous tests during reduction at 600°C. The YSZ coating appeared dense and uniform in SEM analysis. The roughness of the underlying Ni/YSZ anode is on the order of 1 μm, and that may have compromised the gas-tightness of the coating. Further development is warranted to understand and refine the coating process. Thin YSZ applied via this spin-coating technique could be used as a low-cost, drop-in replacement in large-scale SOFC manufacturing processes, improving cell performance and lowering the cost per watt of SOFCs.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Surface Regulating of a Double–Perovskite Electrode for Protonic Ceramic Fuel Cells to Enhance Oxygen Reduction Activity and Contaminants Poisoning Tolerance

Protonic ceramic fuel cells (PCFCs) are one of the most efficient energy conversion devices. However, the performance of current PCFCs is greatly limited by the sluggish oxygen reduction reaction (ORR) kinetics and the fast degradation of cathode due to contaminants poisoning (such as Cr species and steam). In this work, we report a surface regulating of a double perovskite PrBa 0.5 Sr 0.5 Co 1.5 Fe 0.5 O 5+δ (PBSCF) cathode by a Pr 0.9 Fe 0.7 Co 0.3 O 3 (PFC) catalyst coating to enhance the ORR activity and stability. When tested in direct contact with Cr in the air with 3% H 2 O at 650 °C, the polarization resistance (Rp) of the PFC-PBSCF electrode increases from $\approx$0.39 to 0.45 Ω cm 2 after 100 h operation; in contrast, the R p of a PBSCF electrode increases from 0.63 to 0.82 Ω cm 2 . Further, a PCFC with the PFC-PBSCF cathode demonstrates an excellent peak power density ($\approx$1.08 W cm -2 at 650 °C) and significantly enhanced durability (degradation rate of 0.03 % h -1 ), much better than those of the cells with a PBSCF cathode ($\approx$0.75 W cm -2 and degradation rate of 0.12 % h -1 ). Raman spectroscopy and density functional theory calculations indicate that the PFC catalyst coating diminishes the formation of Cr species, such as (Ba 1-x Sr x )CrO 4 , on the cathode surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Structure Development in Cross-Linked, Soybean Oil-based Waterborne Polyurethanes

Development of waterborne polyurethanes (WPU) using bio-based sources represents a step towards sustainable materials science and industry. We synthesized bio-based cationic water-dispersed crosslinked polyurethanes from high oleic soybean oil (HOSO) polyol, isophorone diisocyanate, and methyldiethanol amine, with varying ionic group contents after neutralization with acetic acid. Our primary objective was to analyze how crosslinking affects the dispersion process and film properties in multifunctional systems. The synthesis-structure-property relationship is elucidated through comprehensive analyses of the products at different stages of the synthesis. The dispersion of the WPU particles in water must occur prior to gelation during the final preparation, leading to incomplete conversion and the formation of imperfect networks. Insight into the synthesis process and polymer structure was gained by simulating polymer network parameters. Morphological analyses using synchrotron-based X-ray scattering and atomic force microscopy revealed a hierarchical structure within the WPU films. Importantly, all the films prepared in this study, without using coalescence agents, have low water absorption and high water contact angles, demonstrating their potential for textile and leather coatings and other applications.

bio-based polymers↗

NASA NTRS2011

Distributed Capacitive Sensor for Sample Mass Measurement

Previous robotic sample return missions lacked in situ sample verification/ quantity measurement instruments. Therefore, the outcome of the mission remained unclear until spacecraft return. In situ sample verification systems such as this Distributed Capacitive (DisC) sensor would enable an unmanned spacecraft system to re-attempt the sample acquisition procedures until the capture of desired sample quantity is positively confirmed, thereby maximizing the prospect for scientific reward. The DisC device contains a 10-cm-diameter pressure-sensitive elastic membrane placed at the bottom of a sample canister. The membrane deforms under the weight of accumulating planetary sample. The membrane is positioned in close proximity to an opposing rigid substrate with a narrow gap. The deformation of the membrane makes the gap narrower, resulting in increased capacitance between the two parallel plates (elastic membrane and rigid substrate). C-V conversion circuits on a nearby PCB (printed circuit board) provide capacitance readout via LVDS (low-voltage differential signaling) interface. The capacitance method was chosen over other potential approaches such as the piezoelectric method because of its inherent temperature stability advantage. A reference capacitor and temperature sensor are embedded in the system to compensate for temperature effects. The pressure-sensitive membranes are aluminum 6061, stainless steel (SUS) 403, and metal-coated polyimide plates. The thicknesses of these membranes range from 250 to 500 m. The rigid substrate is made with a 1- to 2-mm-thick wafer of one of the following materials depending on the application requirements glass, silicon, polyimide, PCB substrate. The glass substrate is fabricated by a microelectromechanical systems (MEMS) fabrication approach. Several concentric electrode patterns are printed on the substrate. The initial gap between the two plates, 100 m, is defined by a silicon spacer ring that is anodically bonded to the glass substrate. The fabricated proof-of-concept devices have successfully demonstrated tens to hundreds of picofarads of capacitance change when a simulated sample (100 g to 500 g) is placed on the membrane.

Toda, Risaku↗

DOE OSTI2022

Hierarchical Thiospinel NiCo 2 S 4 /Polyaniline Hybrid Nanostructures as a Bifunctional Electrocatalyst for Highly Efficient and Durable Overall Water Splitting

The development of a nonprecious, stable, and highly effective electrocatalyst for decomposition of water into oxygen and hydrogen is vitally important for sustainable energy conversion, but it still remains challenging to replace the noble metal electrocatalysts with more economically viable alternatives. Here, in this paper, a polyaniline (PANI) decorated hierarchical nickel cobalt thiospinel (NiCo 2 S 4 ) hybrid catalyst (NCS-P) has been developed that shows enhanced dual catalytic activity for both the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER) compared to pristine NiCo 2 S 4 (NCS). Benefiting from the conductive PANI coating, the hierarchical NCS-P nanostructure exhibits outstanding electrocatalytic activity in alkaline solution with low overpotentials of 273 ± 3 and 77 ± 4 mV at 10 mA cm -2 and low Tafel slopes of 42.2 and 68.5 mV dec -1 for OER and HER, respectively, which are better than those of the benchmark noble-metal-based RuO 2 and Pt/C.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Out-of-equilibrium processes in crystallization of organic-inorganic perovskites during spin coating

Complex phenomena are prevalent during the formation of materials, which affect their processing-structure-function relationships. Thin films of methylammonium lead iodide (CH 3 NH 3 PbI 3 , MAPI) are processed by spin coating, antisolvent drop, and annealing of colloidal precursors. The structure and properties of transient and stable phases formed during the process are reported, and the mechanistic insights of the underlying transitions are revealed by combining in situ data from grazing-incidence wide-angle X-ray scattering and photoluminescence spectroscopy. Here, we report the detailed insights on the embryonic stages of organic-inorganic perovskite formation. The physicochemical evolution during the conversion proceeds in four steps: i) An instant nucleation of polydisperse MAPI nanocrystals on antisolvent drop, ii) the instantaneous partial conversion of metastable nanocrystals into orthorhombic solvent-complex by cluster coalescence, iii) the thermal decomposition (dissolution) of the stable solvent-complex into plumboiodide fragments upon evaporation of solvent from the complex and iv) the formation (recrystallization) of cubic MAPI crystals in thin film.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Optimization and understanding of ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst for enhanced CO 2 -methanol conversion at low temperature and pressure

Cu-ZnO-Al 2 O 3 is the most widely applied catalyst for CO 2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalysts have been successfully demonstrated. Here, by using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al 2 O 3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h –1 kg –1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO 2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO 2 dissociation.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2024

Wet chemistry-synthesized Fe/mixed ferrite soft magnetic composites for high-frequency power conversion

State-of-the-art soft magnetic (SM) alloy systems such as electrical steels and permalloys exhibit large eddy current losses at high-frequency (kHz range and above), limiting their application in fast switching devices. Eddy current losses can be reduced for metallic alloys through a decrease in characteristic length scale or embedding them in an insulation layer. This work proposes the development of fine-scale core materials consisting of metallic SM nano/microparticles with magnetic, inorganic insulation layers, and their synthesis using a wet chemistry-based, scalable method for high frequency and high-power applications. More specifically, a magnetic ferrite coating (Ni 0.5-x Mn x Zn 0.5 Fe 2 O 4 , x = 0.0–0.5) was applied via deposition of ferrite powder produced using a “wet chemistry-based” co-precipitation method; the ferrite was distributed through the Fe micropowder via either ball milling or ultrasonic mixing. Powder cores were prepared by compaction of the synthesized composites. Relative magnetic permeability and core loss were measured at excitation frequencies to 200 kHz. A core loss of 127 kW/m 3 was measured at excitation frequency of 100 kHz and magnetization of 0.02 T. This value improves on the 199.3 kW/m 3 reported in literature at identical excitation conditions for a compact formed from a composite comprising Fe microparticles coated with low-permeability Ni 0.5 Zn 0.5 Fe 2 O 4 . Ultrasonic mixing resulted in slightly lower core loss than ball milling, possibly because ball milling causes loss-increasing deformation of the Fe micropowder. XRD and SEM were used to observe composite composition and core cross-section microstructure.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Atomic Layer Deposition for Enhanced Reactivity and Stability of Biomass Conversion Catalysts

Heterogeneous catalysts are an essential tool in the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions (e.g., high temperatures, acidity, oxidizing/reducing environments) of many key biomass conversion processes give rise to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Active site poisoning due to the relatively high sulfur content of most biomass feedstocks further compounds these durability problems. Next-generation catalysts must be developed to address these stability challenges. In this work, we used a scalable atomic layer deposition (ALD) process to modify conventional Pd-based hydrogenation catalysts to generate significant performance improvements. TiO2 ALD coatings were found to increase the activity of Pd/Al2O3 catalysts towards naphthalene hydrogenation; additionally, these coatings improved the catalyst's resistance to sulfur poisoning and thermal stability under oxidative calcination. Additional work in which Al2O3 ALD coatings were applied to Pd/TiO2 catalysts for muconic acid hydrogenation found similar stability benefits, including improved resistance to Pd leaching in the acidic environment. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts and this work constitutes an important examination of applying ALD coatings to supported Pd hydrogenation catalysts.

ALD↗

DOE OSTI2020

Experimental Insights into the Coupling of Methane Combustion and Steam Reforming in a Catalytic Plate Reactor in Transient Mode

The microstructured reactor concept is very promising technology to develop a compact reformer for distributed hydrogen generation. In this work, a catalytic plate reactor (CPR) is developed and investigated for the coupling of methane combustion (MC) and methane steam reforming (MSR) over Pt/Al 2 O 3 -coated microchannels in cocurrent and counter-current modes in transient experiments during start-up. A three-dimensional (3D) computational fluid dynamics (CFD) simulation shows uniform velocity and pressure distribution profiles in microchannels. For a channel velocity from 5.1 to 57.3 m/s in the combustor, the oxidation of methane is complete and self-sustainable without explosion, blow-off, or extinction; nevertheless, flashbacks are observed in counter-current mode. In the reformer, the maximum methane conversion is 84.9% in cocurrent mode, slightly higher than that of 80.2% in counter-current mode at a residence time of 33 ms, but at the cost of three times higher energy input in the combustor operating at ~1000 °C. Nitric oxide (NO) is not identified in combustion products, but nitrous oxide (N 2 O) is a function of coupling mode and forms significantly in cocurrent mode. Furthermore, this research would be helpful to establish the start-up strategy and environmental impact of compact reformers on a small scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1972

Development of uniform and predictable battery materials for nickel-cadmium aerospace cells

The objective of this study was to analyze battery materials and manufacturing methods with the aim of developing uniform and predictable battery plates for nickel cadmium aerospace cells. The results are presented of an extensive factorially-designed experiment aimed at illuminating, in a comparative study, the effect of plaque preparation, plaque thickness, impregnation process, and loading level with active material. The following impregnation processes were investigated: (1) chemical conversion, (2) electrochemical conversion, and (3) high temperature electrochemical impregnation. The test parameter on which the conclusion regarding the manufacturing variables are based was the capacity change during a simulated near-earth orbit cycle regime. As operational variables, the effect of various charge and discharge rates was investigated. During the 100 test cycles, overall capacity changes of positive plates and the differences between the various plates were found to be small. Plates prepared by the high temperature electrochemical impregnation of slurry-coated plaque (at the conditions used) showed surface buildup of active material. They also retained slightly less of their capacity during cycling compared to other plate preparations.

Source record↗

DOE OSTI2023

Mesoporous CuFe 2 O 4 Photoanodes for Solar Water Oxidation: Impact of Surface Morphology on the Photoelectrochemical Properties**

Abstract Metal oxide‐based photoelectrodes for solar water splitting often utilize nanostructures to increase the solid‐liquid interface area. This reduces charge transport distances and increases the photocurrent for materials with short minority charge carrier diffusion lengths. While the merits of nanostructuring are well established, the effect of surface order on the photocurrent and carrier recombination has not yet received much attention in the literature. To evaluate the impact of pore ordering on the photoelectrochemical properties, mesoporous CuFe 2 O 4 (CFO) thin film photoanodes were prepared by dip‐coating and soft‐templating. Here, the pore order and geometry can be controlled by addition of copolymer surfactants poly(ethylene oxide)‐ block ‐poly(propylene oxide)‐ block ‐poly(ethylene oxide) (Pluronic® F‐127), polyisobutylene‐ block ‐poly(ethylene oxide) (PIB‐PEO) and poly(ethylene‐ co ‐butylene)‐ block ‐poly(ethylene oxide) (Kraton liquid™‐PEO, KLE). The non‐ordered CFO showed the highest photocurrent density of 0.2 mA/cm 2 at 1.3 V vs. RHE for sulfite oxidation, but the least photocurrent density for water oxidation. Conversely, the ordered CFO presented the best photoelectrochemical water oxidation performance. These differences can be understood on the basis of the high surface area, which promotes hole transfer to sulfite (a fast hole acceptor), but retards oxidation of water (a slow hole acceptor) due to electron‐hole recombination at the defective surface. This interpretation is confirmed by intensity‐modulated photocurrent (IMPS) and vibrating Kelvin probe surface photovoltage spectroscopy (VKP‐SPS). The lowest surface recombination rate was observed for the ordered KLE‐based mesoporous CFO, which retains spherical pore shapes at the surface resulting in fewer surface defects. Overall, this work shows that the photoelectrochemical energy conversion efficiency of copper ferrite thin films is not just controlled by the surface area, but also by surface order.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Aging gracefully? Investigating iridium oxide ink's impact on microstructure, catalyst/ionomer interface, and PEMWE performance

Here, in this study, we conducted a thorough investigation of the impact of aging iridium oxide (IrO 2 ) perfluorosulfonic acid ionomer ink for up to 14 days on the properties of the ink and the resulting catalyst layers. We examined ink properties, such as zeta potential, dynamic light scattering (DLS), density, surface tension, and rheology, as functions of ink aging time. To evaluate the microstructure and catalyst/ionomer interface, we employed transmission electron microscopy (TEM), X-ray scattering, and X-ray photoelectron spectroscopy (XPS) techniques. Furthermore, we assessed the effect of ink aging on the performance of proton exchange membrane water electrolyzers (PEMWEs). Our findings reveal that most ink properties remain stable for 14 days. The variations in PEMWE cell performance are minimal, and no clear trend is observed in relation to ink aging time. This study demonstrates that the effects of aging the inks for 14 days on ink properties, catalyst layer structure, catalyst/ionomer interface, and PEMWE performance are negligible, indicating a substantial time window after ink preparation without any significant changes in its properties. These insights provide crucial guidance for the commercial production and coating processes of ink, which is necessary for scaling up PEM technologies to meet future demand.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS2013

Nickel-Graphite Composite Compliant Interface and/or Hot Shoe Material

Next-generation high-temperature thermoelectric-power-generating devices will employ segmented architectures and will have to reliably withstand thermally induced mechanical stresses produced during component fabrication, device assembly, and operation. Thermoelectric materials have typically poor mechanical strength, exhibit brittle behavior, and possess a wide range of coefficient of thermal expansion (CTE) values. As a result, the direct bonding at elevated temperatures of these materials to each other to produce segmented leg components is difficult, and often results in localized microcracking at interfaces and mec hanical failure due to the stresses that arise from the CTE mismatch between the various materials. Even in the absence of full mechanical failure, degraded interfaces can lead to increased electrical and thermal resistances, which adversely impact conversion efficiency and power output. The proposed solution is the insertion of a mechanically compliant layer, with high electrical and thermal conductivity, between the low- and high-temperature segments to relieve thermomechanical stresses during device fabrication and operation. This composite material can be used as a stress-relieving layer between the thermoelectric segments and/or between a thermoelectric segment and a hot- or cold-side interconnect material. The material also can be used as a compliant hot shoe. Nickel-coated graphite powders were hot-pressed to form a nickel-graphite composite material. A freestanding thermoelectric segmented leg was fabricated by brazing the compliant pad layer between the high-temperature p- Zintl and low-temperature p-SKD TE segments using Cu-Ag braze foils. The segmented leg stack was heated in vacuum under a compressive load to achieve bonding. The novelty of the innovation is the use of composite material that re duces the thermomechanical stresses en - countered in the construction of high-efficiency, high-temperature therm - o-electric devices. The compliant pad enables the bonding of dissimilar thermoelectric materials while maintaining the desired electrical and thermal properties essential for efficient device operation. The modulus, CTE, electrical, and thermal conductances of the composite can be controlled by varying the ratio of nickel to graphite.

Firdosy, Samad A.↗

DOE OSTI2020

Development of Low Cost, Robust and Durable Cathode Materials to Support Solid Oxide Fuel Cell Commercialization (Final Technical Report)

The project is aimed at addressing critical issues related to chromia-poisoning in the cathode of solid oxide fuel cells. A technical hurdle to the commercialization of solid oxide fuel cells is that chromia sources from the metallic interconnect and the balance of plant (BoP) components will cause chromia-poisoning to the cathode performance. This presents a significant challenge since it is very difficult to eliminate chromia sources in the cathode environment. One aspect of the current project is to evaluate whether SFM (Sr 2 Fe 1.5 Mo 0.5 O 6-δ ) that we have recently developed as redox-stable mixed conducting oxide possesses tolerance to chromia-poisoning. The second focus of this project is to evaluate coating on the cathode materials to mitigate chromia poisoning effect. Both thermodynamic evaluation and experimental approaches have been applied to enhance the knowledge base and fundamental understanding of chromia-tolerance of cathode for solid oxide fuel cells. low cost, robust and durable cathode material to support SOFC commercialization.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2020

Achieving Balanced Crystallization Kinetics of Donor and Acceptor by Sequential-Blade Coated Double Bulk Heterojunction Organic Solar Cells

Sequential deposition has great potential to achieve high performance in organic solar cells due to the resulting well-controlled vertical phase separation. In this work, double bulk heterojunction organic solar cells are fabricated by sequential-blade cast in ambient conditions. Probed by the in situ grazing incidence X-ray diffraction and in situ UV–vis absorption measurements, the seq-blade system exhibits a different tendency from each of the binary films during the film formation process. Due to the extensive aggregation of FOIC, the binary PBDB-T:FOIC film displays a strong and large phase separation, resulting in low current density (J sc) and unsatisfactory power conversion efficiency. In the seq-blade cast system, the bottom layer PBDB-T:IT-M produces many crystal nuclei for the top layer PBDB-T:FOIC, so the PBDB-T molecules are able to crystallize easily and quickly. Balanced crystallization kinetics between polymer and small molecule and an ideal percolation network in the film are observed. In addition, the balanced crystallization kinetics are favorable toward realizing lower recombination loss through charge transport processes.

14 SOLAR ENERGY↗

DOE OSTI2023

Perovskite Solar Module: Promise and Challenges in Efficiency, Meta‐Stability, and Operational Lifetime

Abstract Perovskite photovoltaics (PVs) are an emerging solar energy generation technology that is nearing commercialization. Despite the unprecedented progress in increasing power conversion efficiency (PCE) for perovskite solar cells (PSCs), up‐scaling lab‐made cells to solar modules remains a challenge. In this work, the recent progress of making perovskite mini‐modules is reviewed. In particular, a database summarizing the module size, performance, hysteresis, and operational lifetimes reported in the literature is built. After analyzing the performance losses from scaling PSCs to mini‐modules based on the data collected from the literature, the current key to high‐performance perovskite mini‐modules is found to be the coating method optimization. If the perovskite layer quality is well reserved, a >24% mini‐module efficiency is projected by only considering the losses from lateral resistivity and laser scribing area. Next, performance characteristics are explored including hysteresis and meta‐stable power outputs that must be overcome to correctly characterize perovskite modules. Finally, current challenges associated with the long‐term stability of perovskite modules are examined and the importance of such durability for commercialization is discussed. It is hoped that the findings in this review provide a bridge for the development of perovskite modules that will lead to commercialization in the near future.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Thermodynamically Stable, Plasmonic Transition Metal Oxide Nanoparticle Solar Selective Absorbers towards 95% Optical-to-Thermal Conversion Efficiency at 750 °C

Generation 3 (Gen) concentrating solar power (CSP) systems requires a high operation temperature ≥750°C to increase the power-cycle efficiency towards ≥50%. However, such a high operation temperature poses a notable challenge to high temperature materials. On the receiver side, a critical challenge is the lack of solar selective absorbers that demonstrate both high optical-to-thermal energy conversion efficiency η therm approaching 95% and long-term thermal stability at >750°C in air. Existing solar absorbers either have limited η therm ≤89% or deteriorate significantly within 500 h at 750°C; some of these also require costly vacuum deposition for stringent thickness control. Therefore, it is highly desirable to simultaneously achieve η therm ~95% AND high thermal stability at 750°C for future generations of CSP receivers. This project has investigated and developed low-cost, highly scalable spray-coated transition metal oxide nanoparticle (NP) pigmented solar selective coatings on various types of Inconel alloy tube sections that are thermodynamically stable at 750-800°C in air, maintaining η therm >94.3%(93.2%) under a solar concentration ratio of C=1000 after 60 simulated day-night cycles at 750ºC (800ºC) (1 cycle=12 h at 750 or 800°C and 12h ramping down to 25°C). We have also coated up to 48 inches long receiver tubes for preliminary solar testing under Norwich Technology’s parabolic trough systems, demonstrating notably improved performance in solar heating compared to benchmark Pyromark 2500 coatings. Two key innovations have been developed in this project: (1) We achieved an unprecedented high thermal efficiency >94% by optimizing the d-band optical absorption spectra of transition metal ions, engineering their valences and stoichiometry; (2) We were able to maintain or even slightly increase the efficiency when operating at 750°C in air by engineering the interdiffusion of transition metal ions between the coating and the Inconel substrate to our advantage. Featuring high-temperature solar spectral selectivity and thermodynamic stability in air, as well as low-cost, highly scalable solution-chemical synthesis and spray coating techniques, this innovation in solar selective absorber technology alone accounts for nearly 40% of the targeted reduction in the levelized cost of electricity (LCOE) from the receiver, thermal energy storage, and operation & maintenance combined by 2030, as proposed by the U.S. Department of Energy. For a 110 MWe CSP power plant, this LCOE reduction from the solar selective coating alone transfers to ~$\$ $1.9 M increase in annual profit based on a sales price of 10¢/kWh (or an annual sale of $50 M/year). The high solar absorptance (~98%) NP pigment materials developed in this project are equally applicable to volumetric receivers either as a coating or as bigger ceramic microspheres after sintering, potentially benefiting Gen3 falling particle CSP technologies. All these contributions facilitate the larger scale deployment of CSP systems with energy storage capability to address the intermittency issue of solar energy towards dispatchable solar electricity, bridging the temporal gap between peak solar electricity production and peak electricity consumption. The collaboration with Norwich Technologies and Brayton Energy in this project will also facilitate the future commercialization of this new solar selective coating technology developed in this SIPS project.

14 SOLAR ENERGY↗