Search NASA⌕ Search

SEARCH · Search NASA

Results for “mass diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

Low-Profile Diffuser

The propellant tanks used in liquid rockets require pressurization gases in order to maintain tank pressure while the tanks are being drained during engine operation. The pressurization gas, which is typically much warmer than the relatively cold propellants in the tank, must be introduced into the empty ullage space at the top of the tank. The purpose of the diffuser is to control the flow of the gas into the tank in order to prevent direct impingement of the gas on the liquid surface and/or the tank walls. If the diffuser did not perform those tasks, the warm gas can create excess heat transfer causing an increase in the amount of pressurization mass required. Typical diffusers are long vertical cylinders that create a large exit area in order to minimize gas velocities. However, long vertical cylinders limit the amount of liquid that can be loaded into the tank in order not to have the liquid surface near the diffuser. A design goal for a pressurization diffuser is to create uniform flow in order to prevent jets that can impact the liquid surface and/or tank walls. The purpose of the task was to create a diffuser design that had a lower vertical profile (in order to be able to raise the liquid surface) while still maintaining uniform flow.

Martin, Michael A.↗

Application of Biodegradable Oils (VOS{sup TM}) for Treatment of Chlorinated Ethenes in the Vadose Zone - 12085

Few active remediation alternatives are available to treat residual chlorinated volatile organic compounds (cVOCs) within the vadose zone. Soil vapor extraction (SVE) can be very effective at removing cVOCs in permeable soils; however, recoveries decline substantially in low permeability zones where mass transfer is diffusion-limited. Entrapped cVOCs in these zones represent a slow but continuous source of contamination to underlying groundwater. An ongoing field study was initiated at the Department of Energy's Savannah River Site (SRS) to evaluate an in situ biological treatment technology to address cVOC contamination in the vadose zone. Developed by Savannah River National Laboratory (SRNL), VOS{sup TM} is a thixotropic (shear thinning) formulation of biodegradable oil, water, nutrients, buffers, and de-chlorinating bacteria (Dehalococcoides sp.) that is designed to sequester and biodegrade slow-diffusing cVOCs from unsaturated, low permeable soils. Injection of 871 L (230 gal) of VOS{sup TM} resulted in a rapid and significant decrease in cVOC gas concentration, generation of cVOC daughter products, a decrease in oxygen concentration, and an increase in carbon dioxide and methane production. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Model Implementation of Boron Removal Using CaCl{sub 2}-CaO-SiO{sub 2} Slag System for Solar-Grade Silicon

A new CaCl{sub 2}-CaO-SiO{sub 2} slag system was recently proposed to remove boron from metallurgy-grade silicon by oxidized chlorination and evaporation. To further investigate the boron transformation process at a high temperature, a model implementation to present the transfer of boron from molten silicon to the gas phase via slag is introduced. Heat transfer, fluid flow, the chemical reactions at the interface and surface, the mass transfer and diffusion of boron in the molten silicon and slag, and the evaporation of BOCl and CaCl{sub 2} were coupled in this model. After the confirmation of the thermal field, other critical parameters, including the boron partition ratios (L{sub B}) for this slag from 1723 K to 1823 K (1450 °C to 1550 °C), the thicknesses of the velocity boundary layer at the surface and interface, the mass transfer coefficients of the boundary layer at the surface and interface, and partial pressure of BOCl in the gas phase were analyzed to determine the rate-limiting step. To verify this model implementation, boron removal experiments were carried out at various temperatures and with various initial mass ratios of slag to silicon (μ). The evaporation rate of CaCl{sub 2} was also measured by thermogravimetry analysis (TGA).

36 MATERIALS SCIENCE↗

Pore connectivity influences mass transport in natural rocks: Pore structure, gas diffusion and batch sorption studies

For this work, six rocks (one granodiorite, one limestone, two chalks, one mudstone, and one dolostone) with different extents of heterogeneity at six different particle sizes (from 75 to 8000 μm) were studied to describe the effects of pore connectivity on mass transport. The methods applied were (i) porosity measurement of granular rocks, (ii) analyses of gas-phase diffusive transport in a bed of packed particles, along with a solid quartz method at these six particle sizes being developed to identify the contribution of intraparticle diffusion, and (iii) batch sorption tests of multiple ions (anions and cations) with subsequent analyses of inductively coupled plasma-mass spectrometry. Granular porosity measurement results reveal that with decreasing particle sizes, the effective porosities for the “heterogenous” group of rocks (Grimsel granodiorite and Edwards limestone) increase, whereas the porosities of another “homogeneous” group (two Israel chalk samples, Japan mudstone, and Wyoming dolostone) remain constant. Gas diffusion results show that the intraparticle gas diffusion coefficient among these two sample groups, varying in the magnitude of 10 -8 to 10 -6 m 2 /s, are not directly correlated to the porosity differences. Moreover, the batch sorption work displays a different affinity of rocks for various tracers. For Grimsel granodiorite, Japan mudstone, and Wyoming dolostone, the adsorption capacity of Sm 3+ and Eu 3+ increases as the particle size decreases. In general, this integrated research of grain size distribution, granular rock porosity, intraparticle diffusivity, and ionic sorption capacity gives insights into the pore connectivity effect on both physical and chemical transport behaviors for different lithologies and/or different particle sizes.

58 GEOSCIENCES↗

Summary of Free-flight Performance of a Series of Ram-jet Engines at Mach Numbers from 0.80 to 2.20

Data obtained from the NACA air-launched ram-jet program are summarized with emphasis placed upon the transonic propulsive thrust potential of the engines. Data are presented for boosted and non-boosted engine configurations which incorporate a single-oblique-shock or double-oblique-shock diffuser designed for critical inlet operation at flight Mach numbers of 1.8 and 2.4, respectively. The engines are evaluated in terms of flight Mach number, mass-flow ratio, diffuser pressure recovery, combustion-chamber heat release, propulsive thrust, external drag, and specific impulse. From specific impulse considerations, it appears that for some air-launched missile applications the self-accelerating supersonic ram jet may have a lower gross weight than a rocket-boosted ram jet.

RESEARCH EQUIPMENT, FREE-FLIGHT↗

Conversion of batch to molten glass, II: Dissolution of quartz particles

Quartz dissolution during the batch-to-glass conversion influences the melt viscosity and ultimately the temperature at which the glass forms. Batches to make a high-alumina borosilicate glass (formulated for the vitrification of nuclear waste) were heated as 5°C min-1 and quenched from the temperatures of 400-1200°C at 100°C intervals. As a silica source, the batches contained quartz with particles ranging from 5 to 195 µm. The content of unreacted quartz in the samples was determined with x-ray diffraction. Most of fine quartz has dissolved during the early batch reactions (at temperatures <800°C), whereas coarser quartz dissolved mostly in a continuous glass phase via diffusion. The mass-transfer coefficients were assessed from the data as functions of the initial particle sizes and the temperature. A series of batch was also tested that contained nitrated components and additions of sucrose known to accelerate melting. While sucrose addition had no discernible impact on quartz dissolution, nitrate batches melted somewhat more slowly than batches containing carbonates and hydroxides in addition to nitrates.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Investigation of Perforated Convergent-divergent Diffusers with Initial Boundary Layer

An experimental investigation was made at Mach number 1.90 of the performance of a series of perforated convergent-divergent supersonic diffusers operating with initial boundary layer, which was induced and controlled by lengths of cylindrical inlets affixed to the diffusers. Supercritical mass-flow and peak total-pressure recoveries were decreased slightly by use of the longest inlets (4 inlet diameters in length). Combinations of cylindrical inlets, perforated diffusers, and subsonic diffuser were evaluated as simulated wind tunnels having second throats. Comparisons with noncontracted configurations of similar scale indicated conservatively computed power reductions of 25 percent.

DIFFUSERS, SUPERSONIC↗

Plasma transport in an Eulerian AMR code

A plasma transport model has been implemented in an Eulerian AMR radiation-hydrodynamics code, xRage, which includes plasma viscosity in the momentum tensor, viscous dissipation in the energy equations, and binary species mixing with consistent species mass and energy fluxes driven by concentration gradients, ion and electron baro-diffusion terms and temperature gradient forces. The physics basis, computational issues, numeric options, and results from several test problems are discussed. The transport coefficients are found to be relatively insensitive to the kinetic correction factors when the concentrations are expressed with the molar fractions and the ion mass differences are large. The contributions to flow dynamics from plasma viscosity and mass diffusion were found to increase significantly as scale lengths decrease in an inertial confinement fusion relevant Kelvin-Helmholtz instability mix layer. The mixing scale lengths in the test case are on the order of 100 μm and smaller for viscous effects to appear and 10 μm or less for significant ion species diffusion, evident over durations on the order of nanoseconds. The temperature gradient driven mass flux is seen to deplete a high Z tracer ion at the ion shock front. The plasma transport model provides the generation of the atomic mix per unit of interfacial area between two species with no free parameters. The evolution of the total atomic mix then depends also on an accurate resolution or estimate of the interfacial area between the species mixing by plasma transport. High resolution simulations or a more Lagrangian-like treatment of species interfaces may be required to distinguish plasma transport and numerical diffusion in an Eulerian computation of complex and dynamically evolving mix regions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fabrication of free-standing NiCo{sub 2}O{sub 4} nanoarrays via a facile modified hydrothermal synthesis method and their applications for lithium ion batteries and high-rate alkaline batteries

Graphical abstract: Hydrothermal-synthesized NiCo{sub 2}O{sub 4} nanoflake arrays exhibit porous structure and high capacity as well as good cycling life for lithium ion batteries and alkaline batteries. - Highlights: • Self-supported NiCo{sub 2}O{sub 4} nanoflake arrays are prepared by a hydrothermal method. • NiCo{sub 2}O{sub 4} nanoflake arrays show high capacity and good cycling life. • Porous nanoflake arrays structure is favorable for fast ion/electron transfer. - Abstract: Self-supported NiCo{sub 2}O{sub 4} nanoflake arrays on nickel foam are prepared by a facile hydrothermal method. The obtained NiCo{sub 2}O{sub 4} nanoflakes with thicknesses of ∼25 nm grow vertically to the nickel foam substrate and form an interconnected porous network with pore diameters of 50–500 nm. As anode material of LIBs, the NiCo{sub 2}O{sub 4} nanoflake arrays show a high initial coulombic efficiency of 76%, as well as good cycling stability with a capacity of 880 mAh g{sup −1} at 0.5 A g{sup −1}, and 523 mAh g{sup −1} at 1.5 A g{sup −1} after 50 cycles. As the cathode of alkaline batteries, a high capacity of 95 mAh g{sup −1} is achieved at 2 A g{sup −1} and 94% retention is maintained after 10,000 cycles. The superior electrochemical performance is mainly due to the unique nanoflake arrays structure with large surface area and shorter diffusion length for mass and charge transport.

36 MATERIALS SCIENCE↗

Thermokinetics of point defects in α-Fe 2 O 3

Abstract Point defect formation and migration in oxides governs a wide range of phenomena from corrosion kinetics and radiation damage evolution to electronic properties. In this study, we examine the thermodynamics and kinetics of anion and cation point defects using density functional theory in hematite ( α -Fe 2 O 3 ), an important iron oxide highly relevant in both corrosion of steels and water-splitting applications. These calculations indicate that the migration barriers for point defects can vary significantly with charge state, particularly for cation interstitials. Additionally, we find multiple possible migration pathways for many of the point defects in this material, related to the low symmetry of the corundum crystal structure. The possible percolation paths are examined, using the barriers to determine the magnitude and anisotropy of long-range diffusion. Our findings suggest highly anisotropic mass transport in hematite, favoring diffusion along the c -axis of the crystal. In addition, we have considered the point defect formation energetics using the largest Fe 2 O 3 supercell reported to date.

36 MATERIALS SCIENCE↗

Pattern Formation in Diffusion Flames Embedded in von Karman Swirling Flows

Pattern formation is observed in nature in many so-called excitable systems that can support wave propagation. It is well-known in the field of combustion that premixed flames can exhibit patterns through differential diffusion mechanism between heat and mass. However, in the case of diffusion flames where fuel and oxidizer are separated initially there have been only a few observations of pattern formation. It is generally perceived that since diffusion flames do not possess an inherent propagation speed they are static and do not form patterns. But in diffusion flames close to their extinction local quenching can occur and produce flame edges which can propagate along stoichiometric surfaces. Recently, we reported experimental observations of rotating spiral flame edges during near-limit combustion of a downward-facing polymethylmethacrylate disk spinning in quiescent air. These spiral flames, though short-lived, exhibited many similarities to patterns commonly found in quiescent excitable media including compound tip meandering motion. Flame disks that grow or shrink with time depending on the rotational speed and in-depth heat loss history of the fuel disk have also been reported. One of the limitations of studying flame patterns with solid fuels is that steady-state conditions cannot be achieved in air at normal atmospheric pressure for experimentally reasonable fuel thickness. As a means to reproduce the flame patterns observed earlier with solid fuels, but under steady-state conditions, we have designed and built a rotating, porous-disk burner through which gaseous fuels can be injected and burned as diffusion flames. The rotating porous disk generates a flow of air toward the disk by a viscous pumping action, generating what is called the von K rm n boundary layer which is of constant thickness over the entire burner disk. In this note we present a map of the various dynamic flame patterns observed during the combustion of methane in air as a function of fuel flow rate and the burner rotational speed.

Nayagam, Vedha↗

Is diffuse intracluster light a good tracer of the galaxy cluster matter distribution?

We explore the relation between diffuse intracluster light (central galaxy included) and the galaxy cluster (baryonic and dark) matter distribution using a sample of 528 clusters at 0.2 ≤ z ≤ 0.35 found in the Dark Energy Survey (DES) Year 1 data. The surface brightness of the diffuse light shows an increasing dependence on cluster total mass at larger radius, and appears to be self-similar with a universal radial dependence after scaling by cluster radius. We also compare the diffuse light radial profiles to the cluster (baryonic and dark) matter distribution measured through weak lensing and find them to be comparable. The IllustrisTNG galaxy formation simulation, TNG300, offers further insight into the connection between diffuse stellar mass and cluster matter distributions – the simulation radial profile of the diffuse stellar component does not have a similar slope with the total cluster matter content, although that of the cluster satellite galaxies does. Regardless of the radial trends, the amount of diffuse stellar mass has a low-scatter scaling relation with cluster’s total mass in the simulation, out-performing the total stellar mass of cluster satellite galaxies. We conclude that there is no consistent evidence yet on whether or not diffuse light is a faithful radial tracer of the cluster matter distribution. Nevertheless, both observational and simulation results reveal that diffuse light is an excellent indicator of the cluster’s total mass.

79 ASTRONOMY AND ASTROPHYSICS↗

Numerical Modeling of Physical Vapor Transport in Contactless Crystal Growth Geometry

Growth from the vapor under conditions of limited contact with the walls of the growth ampoule is beneficial for the quality of the growing crystal due to reduced stress and contamination which may be caused by interactions with the growth container. The technique may be of a particular interest for studies on crystal growth under microgravity conditions: elimination of some factors affecting the crystal quality may make interpretation of space-conducted processes more conclusive and meaningful. For that reason, and as a part of our continuing studies on 'contactless' growth technique, we have developed a computational model of crystal growth process in such system. The theoretical model was built, and simulations were performed using the commercial computational fluid dynamics code, (CFD) ACE. The code uses an implicit finite volume formulation with a gray discrete ordinate method radiation model which accounts for the diffuse absorption and reflection of radiation throughout the furnace. The three-dimensional model computes the heat transfer through the crystal, quartz, and gas both inside and outside the ampoule, and mass transport from the source to the crystal and the sink. The heat transport mechanisms by conduction, natural convection, and radiation, and mass transport by diffusion and convection are modeled simultaneously and include the heat of the phase transition at the solid-vapor interfaces. As the thermal boundary condition, temperature profile along the walls of the furnace is used. For different thermal profiles and furnace and ampoule dimensions, the crystal growth rate and development of the crystal-vapor and source-vapor interfaces (change of the interface shape and location with time) are obtained. Super/under-saturation in the ampoule is determined and critical factors determining the 'contactless' growth conditions are identified and discussed. The relative importance of the ampoule dimensions and geometry, the furnace dimensions and its temperature, and the properties of the grown material are analyzed. The results of the simulations are compared with related experimental results on growth of CdTe, CdZnTe, ZnTe, PbTe, and PbSnTe crystals by this technique.

Palosz, W.↗

A model for including thermal conduction in molecular dynamics simulations

A technique is introduced for including thermal conduction in molecular dynamics simulations for solids. A model is developed to allow energy flow between the computational cell and the bulk of the solid when periodic boundary conditions cannot be used. Thermal conduction is achieved by scaling the velocities of atoms in a transitional boundary layer. The scaling factor is obtained from the thermal diffusivity, and the results show good agreement with the solution for a continuous medium at long times. The effects of different temperature and size of the system, and of variations in strength parameter, atomic mass, and thermal diffusivity were investigated. In all cases, no significant change in simulation results has been found.

Wu, Yue↗

TOWARD LOW-COST FABRICATION OF MICROCHANNEL PROCESS TECHNOLOGIES - COST MODELING FOR MANUFACTURING DEVELOPMENT

Chemical and energy conversion systems based on microchannel process technology (MPT) demonstrate high performance in applications in which rates are controlled by diffusive heat and mass transfer flux. The performance of MPT-based heat exchangers, absorbers/desorbers and chemical reactors all benefit from process intensification and have been used in a variety of mobile energy conversion systems including fuel reformers/converters, heat pumps and waste heat scavenging technologies. The service environments typical of MPTs often require the devices to be fabricated from metals such as aluminum, titanium, stainless steel or high temperature super alloys. Flow channels and associated critical dimensions in these devices can be as small as 50 um, but generally range from 100 to 1000 um in width and height with characteristic flow channel lengths normally in the mm to cm range. High surface area architectures (e.g. wicks or textured surfaces) are often included in the flow channels as well for enhanced mass transfer and/or catalytic functionality. Fabrication of MPT devices has historically been performed using a stacked-shim approach in which individual metal sheets are first patterned with micro- and meso-scale flow channels and subsequently bonded in a stack to create an array of miniaturized, parallel flow paths. Typical proof-of-concept fabrication efforts have utilized photo chemical machining (PCM) for shim patterning and diffusion bonding or diffusion brazing for joining of shim stacks. While flexible and capable of supporting technology demonstration, however, these techniques can be expensive at prototyping volumes. The high fabrication cost associated with these prototyping processes has contributed to a perception that MPT technology is expensive and will be relegated to a small application space. Recent work at the Microproducts Breakthrough Institute (MBI) has focused on exploring the cost structure of high volume manufacturing of MPT devices in effort to identify new paths to lower cost fabrication. Through systematic exploration of fabrication process capabilities and associated cost structures, the MBI is developing volume-sensitive cost estimation models for predicting manufacturing costs of MPT devices fabricated using different processing technologies. The process-based cost models are used to develop an understanding of the economic trade-offs between candidate processes and are utilized in a design for manufacturing approach to MPT device fabrication. In this paper we present results and analysis of the cost modeling effort to date and apply the methodology in case study of a stainless steel MPT device designed, built and tested by Pacific Northwest National Laboratory. Extensions of the model to adjacent material sets and the interaction of device designs with fabrication processes will be discussed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

A direct numerical method for predicting concentration profiles in a turbulent boundary layer over a flat plate

A numerical solution of the turbulent mass transport equation utilizing the concept of eddy diffusivity is presented as an efficient method of investigating turbulent mass transport in boundary layer type flows. A FORTRAN computer program is used to study the two-dimensional diffusion of ammonia, from a line source on the surface, into a turbulent boundary layer over a flat plate. The results of the numerical solution are compared with experimental data to verify the results of the solution. Several other solutions to diffusion problems are presented to illustrate the versatility of the computer program and to provide some insight into the problem of mass diffusion as a whole.

Dow, J. W.↗

On the Spectral Evolution of Hot White Dwarf Stars. II. Time-dependent Simulations of Element Transport in Evolving White Dwarfs with STELUM

White dwarf stars are subject to various element transport mechanisms that can cause their surface composition to change radically as they cool, a phenomenon known as spectral evolution. In this paper, we undertake a comprehensive theoretical investigation of the spectral evolution of white dwarfs. First, we introduce STELUM, a new implementation of the stellar evolutionary code developed at the Université de Montréal. We provide a thorough description of the physical content and numerical techniques of the code, covering the treatment of both stellar evolution and chemical transport. Then, we present two state-of-the-art numerical simulations of element transport in evolving white dwarfs. Atomic diffusion, convective mixing, and mass loss are considered simultaneously as time-dependent diffusive processes and are fully coupled to the cooling. We first model the PG 1159-DO-DB-DQ evolutionary channel: a helium-, carbon-, and oxygen-rich PG 1159 star transforms into a pure-helium DB white dwarf due to gravitational settling and then into a helium-dominated, carbon-polluted DQ white dwarf through convective dredge-up. We also compute for the first time the full DO-DA-DC evolutionary channel: a helium-rich DO white dwarf harboring residual hydrogen becomes a pure-hydrogen DA star through the float-up process and then a helium-dominated, hydrogen-bearing DC star due to convective mixing. We demonstrate that our results are in excellent agreement with available empirical constraints. In particular, our DO-DA-DC simulation perfectly reproduces the lower branch of the bifurcation observed in the Gaia color–magnitude diagram, which can therefore be interpreted as a signature of spectral evolution.

79 ASTRONOMY AND ASTROPHYSICS↗

Candle Flames in Microgravity: USML-1 Results - 1 Year Later

We report on the sustained behavior of a candle flame in microgravity determined in the glovebox facility aboard the First United States Microgravity Labomtofy. In a quiescent, microgmvjfy environment, diffusive transport becomes the dominant mode of heat and mass transfer; whether the diffusive transport rate is fast enough to sustain low-gravity candle flames in air was unknown to this series of about 70 tests. After an initial transient in which soot is observed, the microgravity candle flame in air becomes and remains hemispherical and blue (apparently soot-Ne) with a large flame standoff distance. Near flame extinction, spontaneous flame oscillations are regularly observed; these are explained as a flashback of flame through a premixed combustible gas followed by a retreat owed to flame quenching. The frequency of oscillations can be related to diffusive transport rates, and not to residual buoyant convective flow. The fact that the flame tip is the last point of the flame to survive suggests that it is the location of maximum fuel reactivity; this is unlike normal gravity, where the location of maximum fuel reactivity is the flame base. The flame color, size, and shape behaved in a quasi-steady manner; the finite size of the glovebox, combined with the restricted passages of the candlebox, inhibited the observation of true steady-state burning. Nonetheless, through calculations, and inference from the series of shuttle tests, if is concluded that a candle can burn indefinitely in a large enough ambient of air in microgravity. After igniting one candle, a second candle in close pximity could not be lit. This may be due to wax coating the wick and/or local oxygen depletion around the second, unlit candle. Post-mission testing suggests that simultaneous ignition may overcome these behaviors and enable both candles to be ignited.

Ross, H. D.↗