SEARCH · Search NASA

Results for “sintering temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Effect of Ni content in Cu 1-x Ni x coating on microstructure evolution and mechanical properties of W/Mo joint via low-temperature diffusion bonding

The 93W and Mo1 refractory metals were bonded with different Cu 1- x Ni x coating interlayers of various Ni content using plasma-activated sintering at 700 °C. The effects of the Ni content in the Cu 1- x Ni x coating interlayer on the interfacial microstructure evolution and mechanical properties of the W/Mo joints were studied. The maximum average shear strength of the W/Mo joint was 316.5 MPa when the Ni content of the Cu 1- x Ni x coating interlayer was 25 %. When the Ni content of the Cu 1- x Ni x coating interlayer was below 50 %, the atomic diffusion at the W/Mo joint interface was adequate without the formation of intermetallic compounds, as demonstrated by the High Resolution Transmission Electron Microscope analyses of the joints. The presence of Ni in Cu 1- x Ni x promoted diffusion bonding at the interface, which contributed to the high mechanical properties of the W/Mo joint. With an increase in the Ni content of the Cu 1- x Ni x coating interlayer, the MoNi intermetallic compound (IMC) nucleated and grew at the Cu 1- x Ni x coating/Mo1 interface. When the Ni content of the Cu 1- x Ni x coating interlayer was above 50 %, the generation of a brittle MoNi IMC weakened the shear strength of the W/Mo joint dramatically.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Development of a Laser Ultrasonics-based Approach for Rapid Screening of High Entropy Alloys

This project utilized a laser ultrasonic technique to systematically study temperature-induced evolution of material properties in a set of interrelated binary alloys and a high entropy alloy (HEA) fabricated using arc-melting and spark plasma sintering processes. This technique involved the use of a nanosecond duration, high-intensity pulsed laser to thermo-elastically generate ultrasonic waves that propagate in the bulk of the metal alloy. Sub-nanometer-scale displacements associated with the propagating bulk ultrasonic waves were detected along the epicenter on the opposite surface of the sample using a 1 GHz bandwidth photorefractive interferometer. Phase transformations and microstructural changes were inferred from the temperature-dependent trends in the bulk acoustic velocities and features in the ultrasonic epicentral waveforms measured in the binary alloys. These inferences were then correlated with electron/optical microscopy observations and predictions using calculations of phase diagrams (CALPHAD). The results showed that the laser-generated ultrasonic pulses were strongly influenced by changes in material microstructure and could accurately track thermally driven phase transformations and detect the presence of microscale heterogeneities (grain boundaries, dendritic structures, etc.) in the set of binary alloy samples. The measurement approach was then applied to a quinary HEA sample for estimating phase transition temperature and determining microstructural heterogeneity. The rapid, non-contact and non-destructive ultrasonic testing approach demonstrated here is amenable to high throughput combinatorial investigations that can be applied to graded composition HEAs produced using advanced manufacturing methods. When paired with atomistic simulations and CALPHAD modeling, this approach can overcome the bottlenecks faced by current material characterization methods in efficiently screening the vast discovery space of HEAs that spans over a hundred million unique quinary alloy compositions.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Spark plasma sintering of fuel meats for U 3 O 8 based dispersion fuels

Research and test reactors often use dispersion-type fuel due to its increased thermal conductivity and burn-up capabilities compared to conventional fuel. Al-U 3 O 8 (aluminumtriuranium octaoxide) dispersion fuels have several advantages over their competitors, such as higher service temperature and better stability of oxygen stoichiometry. However, the two-step fabrication of dispersion fuel causes undesirable porosity in cold-pressed fuel meats that is preserved in co-extruded fuel plates. To combat this, spark plasma sintering (SPS) was used for the fabrication of Al-15, 20, and 30 vol% U 3 O 8 and 8 and 12 vol% Mo-U 3 O 8 fuel meats for the Al-U 3 O 8 time. The in situ SPS data was used to construct and validate Master Sintering Curves (MSCs) with accuracies in Al fuels at 0.02 g/cm 3 , and Mo fuels at 0.07 and 0.17 g/cm 3 . The as-sintered fuel meats were characterised using x-ray diffraction (XRD) and scanning electron microscopy (SEM) to understand chemical and physical changes following the SPS process. The pellets exhibited very high relative densities, the U 3 O 8 was observed to undergo reduction to UO 2 .

Aluminium↗

DOE OSTI2026

Itinerant Magnetism in Hydride-Synthesized CaCo 12 B 6

A new compound in the underexplored Ca–Co–B phase space has been discovered, validating high-throughput computations from the Open Quantum Materials Database, which predicted thermodynamic stability for CaCo 12 B 6 in the SrNi 12 B 6 structure type. The synthetic effects of different boron precursors and the advantages of using CaH 2 instead of Ca metal were demonstrated by the short synthesis duration and high purity of CaCo 12 B 6 , in contrast with traditional synthesis routes. Powder X-ray diffraction (PXRD) confirmed that CaCo 12 B 6 shares the SrNi 12 B 6 structure ( R $\bar{3}$m (#166), a = 9.469(4) Å, c = 7.468(2) Å, Z = 3) and is water- and air-stable. High-temperature in situ PXRD indicates that CaCo 12 B 6 is stable below 1050 K under vacuum in a silica capillary. CaCo 12 B 6 decomposes between 693 and 773 K during spark-plasma sintering. Density functional theory calculations indicate that CaCo 12 B 6 is metallic with a ferromagnetic ground state. X-ray absorption near-edge spectroscopy and Bader charge analysis indicate that Co atoms in CaCo 12 B 6 lack ionic character. Magnetometry reveals room-temperature paramagnetism with μ eff = 1.7(1)μ B per Co atom and a Weiss constant of +190(10)K. Ferromagnetic ordering occurs below 172(1)K, resulting in a saturation moment of 0.46 μ B per Co atom. Our findings demonstrate that the hydride route is a viable strategy for discovery of new ternary alkaline-earth-transition metal borides analogous to rare-earth-containing counterparts.

diffraction↗

DOE OSTI2024

High Temperature Tensile Testing of Molybdenum Before and After Exposure in Flowing He at 600°C to 1000°C

ORNL supported NorthStar Medical Radioisotope’s accelerator-based concept to produce the medical isotope molybdenum-99 (Mo-99). The Mo targets are expected to experience in the accelerator temperature ranging from 200°C to 1000°C, and previous studies have demonstrated the embrittlement of Mo targets at room temperature when exposed to impure He at 800 to 1000°C. The goal of this project was to evaluate potential embrittlement at temperature ranging from 600°C to 1000°C for three Mo materials exposed at the same temperatures for 100h in high purity He (O 2 < 5ppm (µl/l)) with a flow rate of ~1m/s. Enriched Mo-100 (aMo) and conventional pressed and sintered Mo (UHP) disks were provided by NorthStar while low carbon arc cast rolled Mo, fabricated at ORNL, was used for comparison. The as fabricated rolled Mo exhibited superior tensile strength due to the alloy very fine grain size with limited ductility except at 1000°C with the elongation at rupture reaching 30%. The UHP Mo disks showed the lowest strength but highest ductility at 20-1000°C with significant strain hardening during tensile testing. The ductility of the aMo material was quite low at all temperatures due to a high density of voids at grain boundaries. Significant embrittlement of the aMo material was observed after exposure at 600°C to 1000°C, most likely because of oxygen diffusion and segregation at grain boundaries. No embrittlement was observed for the UHP Mo material, with excellent elongation at rupture for some of the specimens oxidized in He and tested at 600-1000°C. Significant variation in ductility from one UHP Mo specimen to another was, however, measured, both in the as fabricated and He-oxidized conditions. The rolled Mo was not affected by oxidation in He at 800°C, but a decrease in strength and increase in ductility was observed at 1000°C, likely due to the material recrystallization.

36 MATERIALS SCIENCE↗

DOE OSTI2024

The Overlooked Potential of Sulfated Zirconia: Reexamining Solid Superacidity Toward the Controlled Depolymerization of Polyolefins

Closed-loop recycling via an efficient chemical process can help alleviate the global plastic waste crisis. However, conventional depolymerization methods for polyolefins, which compose more than 50% of plastics, demand high temperatures and pressures, employ precious noble metals, and yield complex mixtures of products limited to single-use fuels or oils. Superacidic sulfated zirconia (SZrO) with Hammet Acidity Functions (H 0 ) = -12 (i.e., stronger than 100% H 2 SO 4 ) is an industrially deployed heterogeneous catalyst capable of activating hydrocarbons under mild conditions and is shown to decompose polyolefins at ambient pressure and temperatures near 200 °C. Additionally, confinement of active sites in porous supports is known to radically increase selectivity, coking and sintering resistance, and acid site activity, presenting a possible approach to low-energy polyolefin depolymerization. However, a critical examination of the literature on SZrO led us to a surprising conclusion: despite 40 years of catalytic study, engineering, and industrial use, the surface chemistry of SZrO is poorly understood. Ostensibly spurred by SZrO's impressive catalytic activity, the application-driven study of SZrO has resulted in deleterious ambiguity in requisite synthetic conditions and insufficient characterization of acidity, porosity, and active site structure. Here, this ambiguity has produced significant knowledge gaps surrounding the synthesis, structure, and mechanisms of hydrocarbon activation for optimized SZrO, stunting the potential of this catalyst in olefin cracking and other industrially relevant reactions, such as isomerization, esterification, and alkylation. Toward mitigating these long extant issues, we herein identify and highlight these current shortcomings and knowledge gaps, propose explicit guidelines for characterization of and reporting on characterization of solid acidity, and discuss the potential of pore-confined superacids in the efficient and selective depolymerization of polyolefins.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Creep Performance of Novel Composite Heating Elements for Reheat Furnace Electrification

The iron and steel industry is critical for the modern world but is also very energy intensive and is a low margin industry. Hot rolling requires reheating steel slabs to ~1250 °C for hot rolling and involves yield loss due to scale formation. Electrification of this process using resistive heating could improve yield but is currently not possible due to the poor creep resistance of MoSi2 heating elements, which need to be operated well below their maximum temperatures when mounted horizontally. To solve this problem, novel MoSi2 composite heating elements with SiBCN ceramic reinforcements are being developed using high energy ball milling and spark plasma sintering. The creep performance of different heating elements and their corresponding microstructures and electrical properties will be presented.

36 - MATERIALS SCIENCE↗

DOE OSTI2025

NSUF RTE completion report for 23-4780: Microstructural Defect Induced Thermal Conductivity Reduction in Uranium Nitride and Thorium Nitride

Uranium nitride (UN) is known to have a higher thermal conductivity than traditional oxide fuels, which could lead to a more efficient energy transport and lower local temperature during its lifetime. But the thermal transport performance of UN in extreme environments has not been systematic studied. This study investigated the irradiation induced microstructural defects in UN and the impacts on thermal conductivity. The samples were produced by spark plasma sintering at University of Texas-San Antonio (UTSA), Los Alamos National Laboratory (LANL), and Idaho National Laboratory (INL). Thermal conductivity of UN before and after 2MeV proton irradiation were measured by using laser metrology at INL in a temperature range of 77-295K. Thermal conductivity measurements in this wide, cryogenic temperature range is critical to understand the phonon scattering mechanisms between the thermal energy carrier, phonons, and different types of irradiation-induced defects. In order to ensure the measurements were conducted in the same grains and minimize the impact of the local heterogeneities, the measurement locations were highlighted by fiducial marks using the focused ion beam (FIB) with grain orientation identified using the electron backscatter diffraction (EBSD) at the Center of Advanced Energy Studies (CAES). Irradiation experiment was conducted at the Ion Beam Laboratory at Texas A&M University (TAMU). A total of 6 samples were irradiated with different irradiation doses and temperatures. After irradiation, the microstructure was characterized by using Transmission Electron Microscope (TEM) at CAES (also in the FIB marks).

36 - MATERIALS SCIENCE↗

DOE OSTI2023

Biphasic Janus Particles Explain Self-Healing in Pt–Pd Diesel Oxidation Catalysts

The addition of Pd to Pt-based diesel oxidation catalysts is known to enhance performance and restrict the anomalous growth of Pt nanoparticles when subjected to aging at high temperatures in oxidative environments. To gain a mechanistic understanding, we studied the transport of the mobile Pt and Pd species to the vapor phase, since vapor phase transport is the primary route for sintering in these catalysts. The results are surprising: there is a 30-fold drop in the effective vapor pressure of Pt in the Pt-Pd catalysts compared to monometallic Pt. At the same time, there is a significant enhancement in the vapor pressure of Pd, compared to PdO, which otherwise has a negligible vapor pressure at the aging temperature. Such behavior cannot be explained simply by alloying Pt and Pd in the metallic phase, or a core-shell morphology where a PdO shell covers a Pt core. Transmission electron microscopic examination of catalysts aged up to 50 h in air at 800 °C shows that the particles exhibit a biphasic “Janus”-like structure. The metal and oxide phases are conjoined, exposing a metal and an oxide face to the gas phase. The high mobility of the Pt and Pd allows them to be partitioned into the metal and oxide phases, in apparent thermodynamic equilibrium. The PdO helps to trap mobile PtO2 and as a result contains high concentrations of Pt oxide, consistent with its role in mitigating the transport of Pt to the vapor phase and preventing the growth of anomalously large particles. In turn, Pt allows Pd to remain metallic, allowing the catalyst to retain both metal and oxide functionality for catalysis. The regeneration of deactivated catalysts typically requires an external input, such as a change in the working environment from reducing to oxidizing or vice-versa. Here, we show that the mobile species, which are primary contributors to catalyst sintering are effectively returned to the active site, hence our use of the term “selfhealing”. The detailed insights into the inner workings of the Pt-Pd diesel oxidation catalysts can help provide clues to the design of robust and durable heterogeneous catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Temperature-dependent diffuse reflectance measurements of ceramic powders in the near- and mid-infrared spectra

Radiative properties are critical to quantify radiative energy fluxes between surfaces and in participating media. However, there is limited experimental data on temperature-dependent radiative properties of materials. Herein, this work focuses on experimentally measuring temperature-dependent diffuse reflectance in the near- and mid-infrared spectra (1–20 μm) for ceramic particles with applications as heat-transfer and thermal-storage media in concentrated solar power (CSP) plants. Specifically, a commercially available sintered bauxite proppant, ACCUCAST ID80, and its primary chemical constituents—alumina (Al 2 O 3 ) and silica (SiO 2 )—are measured in powder form using a Fourier transform infrared spectrometer (FTIR) coupled with a specialized diffuse reflectance accessory and a heated stage. Room-temperature diffuse reflectance measurements show increased absorption in tests with greater mass fractions of the ceramic samples. There is a strong correlation in the measured reflectance spectra of ACCUCAST with alumina and silica in the spectral range 2000–500 cm –1 (5–20 μm). Whereas, for shorter wavelengths (< 5 μm), the absorptance for ACCUCAST is greater than the absorptance for alumina and silica, indicating contributions from other chemical species present in the composite material. For the first time, temperature-dependent diffuse reflectance measurements are reported for ACCUCAST up to 1000 °C. These results are compared against those of alumina and silica through the calculation of a thermal emittance. All three materials exhibit a calculated emittance of ~0.9 at room temperature. However, this value decreases to ~0.6 for ACCUCAST and drops to less than 0.4 for alumina and silica at 1000 °C. Thermal cycling in air at 1000 °C resulted in a visible color change from dark grey to light orange for ACCUCAST and a subsequent larger increase in reflectance for wavelengths less than 5 μm as compared to ACCUCAST thermally cycled at 1000 °C in vacuum. Alumina and silica spectra proved to be largely unaffected by thermal cycling under atmospheric conditions. Overall, this study establishes a powerful technique for the characterization of radiative properties of particulate materials as a function of temperature and presents a detailed case study of ACCUCAST, a candidate for next-generation particle-based CSP.

14 SOLAR ENERGY↗

DOE OSTI2026

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗

DOE OSTI2023

Hydrothermal catalytic conversion of oleic acid to heptadecane over Ni/ZrO 2

There is growing interest in the substitution of expensive noble metal catalysts with low-cost earth-abundant metals in applications targeting biofuels production from waste organic feedstocks. Here, nickel (Ni) catalysts supported on zirconium dioxide (ZrO 2 ), both with and without copper (Cu) as a co-metal, were tested in hydrothermal reactions of unsaturated and saturated C18 fatty acids as models for waste oil feedstocks. In contrast to recent reports, this study showed no enhancement of nickel's activity for fatty acid conversion to alkane products when Cu was present. Ni/ZrO 2 prepared by metal coprecipitation methods converted 100% of oleic acid with 25% selectivity to heptadecane after 5h of reaction at 350 °C using methanol as a hydrogen donor source, increasing to 41% heptadecane after 20 h. Lower yields were observed with catalysts prepared by wet impregnation and using alternative hydrogen donor sources (glycerol, formic acid). Greater selectivity to heptadecane was also observed at higher temperatures (370 °C) and when the initial fatty acid had greater saturation. Longer term exposure to hydrothermal media led to metal sintering and catalyst deactivation. Findings support a path forward to the development of earth-abundant metal catalysts for the upgrading of waste organic feedstocks.

09 BIOMASS FUELS↗

DOE OSTI2020

3Y-TZP Toughened and Oxidation-resistant U 3 Si 2 Composites for Accident Tolerant Fuels

In this work, we report an innovative approach synergizing multiple effects of microstructure control, oxide protection and phase transformation-induced mechanically toughening to develop advanced U 3 Si 2 fuels with state-of-the-art materials properties. 3Y-TZP (3 mol% yttria doped stabilized tetragonal zirconia) additives are incorporated and uniformly distributed into the SPS-densified U 3 Si 2 fuel matrix, enhancing materials fracture toughness up to 4.04 MPa m 1/2 . The 3Y-TZP incorporated U 3 Si 2 composite pellets show significantly improved onset temperature of oxidation above 560 °C, which can be further improved to 617 °C with 3 vol% addition by post-sintering thermal annealing. We report the development of mechanically tough and oxidation-resistant U 3 Si 2 with minimal additive represents a major step forward towards realizing the potential of high density U 3 Si 2 as the leading fuel concept to increase accidence tolerance of nuclear energy systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Experimental and Numerical Analysis of Additively Manufactured Inconel 718 Coupons With Lattice Structure

Abstract In the present paper, two lattice geometries suitable for near surface and double wall cooling were developed and tested. The first type of unit cell consisted of six ligaments of 0.5 mm diameter joined at a common vertex near the middle. The second type of unit cell was derived from the first type by adding four mutually perpendicular ligaments in the middle plane. Two lattice configurations, referred to as L1 and L2, respectively, were obtained by repeating the corresponding unit cell in streamwise and spanwise directions in an inline fashion. Test coupons consisting of these lattice geometries embedded inside rectangular cooling channel with dimensions of 2.54 mm height, 38.07 mm width, and 38.1 mm in length were fabricated using Inconel 718 powder and selective laser sintering (SLS) process. The heat transfer and pressure drop performance was then evaluated using steady-state tests with constant wall temperature boundary condition and for channel Reynolds number ranging from 2800 to 15,000. The lattices depicted a higher heat transfer compared with a smooth channel and both the heat transfer and pressure drop increased with a decrease in the porosity from L1 to L2. Steady-state conjugate numerical results revealed formation of prominent vortical structures in the inter-unit cell spaces, which diverted the flow toward the top end wall and created an asymmetric heat transfer between the two end walls. In conclusion, these lattice structures provided an augmented heat transfer while favorably redistributing the coolant within channel.

Engineering↗

DOE OSTI2022

Mechanically strengthened heterogeneous Sm-Co sintered magnets

Samarium-cobalt sintered magnets offer excellent magnetic properties, thermal stability, and corrosion resistance. They are used in a variety of defense and civilian applications, especially when elevated operation temperatures (e.g., 200 ºC to 550 ºC) are required. However, the utilization of these materials is restricted by their brittleness. Improving their mechanical resilience would make them more cost-effective, efficient, and robust in decarbonization and other function-related applications while reducing the pressure on critical material supply chains. In this paper, we engineer a series of novel heterogeneous microstructures, such as laminated coarse grain (CG)/fine grain (FG) and core/shell CG/FG microstructures, to produce unprecedented combinations of superior mechanical and magnetic properties without altering the chemical compositions of the magnets or common heat treatment procedures. Further, a 60% flexural strength enhancement is obtained using heterogeneous Sm 2 (CoFeCuZr) 17 sintered magnets with little impact on their magnetic properties. The mechanically robust heterogeneous Sm-Co sintered magnets have a minor (e.g., less than 4.6%) reduction in the energy product (BH) max due to a slightly reduced squareness of the demagnetization curve, with no decrease in either the remanence (B r ) or the intrinsic coercivity (H ci ). The flexural strengths of these heterogeneous Sm-Co magnets depend on the volume ratios and mean grain sizes of the FG/CG regions, as well as their microstructural architectures. The fine-grained regions act as mechanical strengthening sites, which can be strategically used when designing the magnet for different applications. This technology is highly compatible with existing magnet manufacturing processes and thus can be adopted readily by the magnet industry.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Development and Experimental Optimization of High-Temperature Modeling Tools and Methods for Concentrated Solar Power Particle - Systems

A novel, open-source radiative modeling toolset was developed to extend the functionality of particle-based modeling software (e.g. discrete element method (DEM)) to environmental conditions relevant to concentrated solar power applications. This toolset was optimized for deployment on desktop workstations instead of high-performance computing systems, to render such tools more accessible to the research community. Both particle-based modeling and radiative exchange modeling are computationally expensive and often require specialized programming expertise, making these methods cumbersome to use. Recent developments in DEM software by DCS Computing have greatly reduced these challenges, providing a graphical-user-interface based platform and modeling optimization for desktop workstations, HPCs, and cloud computing. The University of Dayton leveraged the experience of DCS Computing in developing a user-friendly, open-source radiative heat transfer expansion for DEM modeling. The University of Dayton DEM+ radiative modeling toolset was developed using a combination of fundamental experimental measurements, modeling, and simplified flow experiments over a range of temperatures and flow conditions. The toolset provides researchers with access to multiple radiative models including an accelerated Monte-Carlo Ray Tracing (application agnostic, highly computationally expensive), an expanded database of distance-based approximations (application limited, computationally light), and a weighted blending of the two methods capable of achieving over 90% reduction in computation time with equivalent accuracy compared to Monte-Carlo Ray Tracing. Through a graphical user interface, users can customize the radiative models to match their desired accuracy and available computational resources, improving access to particle based modeling for the research community. Ceramic sintered bauxite proppants were used in modeling and experimentally as a baseline. Both the radiative heat transfer and flow properties for particulate systems were investigated at elevated temperatures up to 800 °C. The major accomplishments for this work include a verified, open-source radiative modeling toolset to be distributed amongst the research community and the fabrication of three small-scale test facilities to investigate particle behavior and tune DEM flow properties for operation up to 800 °C. The findings have been shared with the research community via conference modeling workshops, deployment of the tools in DCS Computing Aspherix®, and open-source access to the developed radiative modeling tool. The development of next-generation CSP facilities and thermal energy storage systems based on ceramic particles requires providing access to computationally efficient and accurate modeling tools. Particles will experience a wide range of environments (20-800 °C) and handling conditions (dilute curtains or dense packing), requiring specially designed and optimized equipment. Optimizing solid particle physics models and establishing best-practices for particle modeling in CSP environments will assist researchers with designing optimized equipment, accelerating the deployment of more economically-competitive CSP facilities.

14 SOLAR ENERGY↗

DOE OSTI2021

Microwave Synthesis of Spinel MgFe 2 O 4 Nanoparticles and the Effect of Annealing on Photocatalysis

Through microwave heating in ethanol and with subsequent annealing, crystalline MgFe 2 O 4 nanoparticles are produced rapidly and in high yields >99%. Under varied annealing temperatures, the degree of Mg and Fe site inversion changes the optical, electronic, and composition of the nanoparticles. Here, a small particle size of ~10 nm is achievable with the aid of an ammonium salt mineralizer that caps the particles during nucleation and growth. Particles with the lowest inversion parameter and limited sintering upon annealing (at 600 ºC) exhibit the greatest production of hydroxyl radicals under visible light illumination. As such, these particles also facilitate the degradation of methylene blue dye faster than those particles annealed at higher temperature and show a rate constant of 0.061 h –1 for degrading 10 ppm methylene blue with 10 mg catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Accelerating Manufacturing of Powder-Processed Strong, Lightweight and Thermally Stable Bulk Nanocrystalline Al Alloys via Engineered Interface States

The overarching goal of this program is to develop an integrated materials by design framework enabling a simple, scalable, and efficient manufacturing route for thermally stable nanocrystalline Al-based alloys with high specific strength over a range of service temperatures. The central scientific principle underpinning this program is the elucidation, and ultimately implementation in novel alloy design, of unique interfacial structures and chemistries driven by segregation in multi-component systems that give rise to unprecedented processability and properties. This program targeted nanocrystalline Al-based ternary alloys produced by mechanical alloying of powders followed by compaction and sintering with hot pressing, which are inherently scalable and inexpensive manufacturing routes, but when applied to nanocrystalline alloys are usually plagued by low density and/or poor retention of the intended nanostructures during processing. This program successfully demonstrated manufacturing of a bulk (>1 cm 3 ) nanocrystalline Al-based alloy with a combination of thermal stability, high temperature strength retention, and specific strength that exceeds the current-state-of-the-art of Al alloys. It is anticipated that the greatest technological impact will occur by demonstration of rapid and scalable manufacturing of bulk nanocrystalline Al alloys with exceptional thermal stability and mechanical performance, thus enabling increased energy efficiency in high performance power generation systems via: (i) replacement of existing components with lightweight Al-based alloys and (ii) increasing operating temperatures with property retention. The program focused on the development of a simple and efficient manufacturing route for thermally stable nanocrystalline Al-based alloys with high specific strength over a range of service temperatures. The program is expected to have direct impact on scalable and economic manufacturing of bulk nanocrystalline alloys. This program profited from the recent discovery by the project team of segregation-driven amorphous intergranular films in nanocrystalline metallic alloys that can be kinetically frozen-in at sub-solidus temperatures. These interfacial states (also known as amorphous complexions) comprise a large fraction of the total material in nanocrystalline alloys and are responsible for two beneficial characteristics that anchor the proposed work: (1) activated sintering leading to high density and (2) retained nanostructures leading to high strengths that approach a substantial fraction of the theoretical limit. More specifically, these engineered interfaces led to a three-fold benefit: (i) high-throughput materials processing with low energy budget and cost, (ii) exceptional thermal stability, and (iii) high specific strength at both room temperature and intermediate temperatures experienced during service.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗