Results for “target configuration” — Page 20

DOE OSTI2022

High-rate strength response of tantalum from dynamic hole closure experiments

The science and engineering communities have significant interest in experimental platforms to evaluate and improve models for dynamic material deformation. While well-developed platforms exist, there are still gaps to fill for strain and strain rate conditions accessed during impact and other high-rate loading scenarios. To fill one such gap for strength measurements, a platform was recently developed that accesses high strain rate (≥ 10 5 /s) and large strain (≥ 50%) conditions by measuring the transient closure of a cylindrical hole using in situ x-ray imaging. In the work reported here, further refinement of the platform is performed to reduce the potential effects of porosity and anelasticity on the measurement. This helps us to isolate the strength effects that are the focus of the experiment. The updated experimental configuration employs a two-layer flyer design and elongated target to reduce the magnitude of the tensile excursions associated with rarefaction wave interactions. This allows for a more direct assessment of strength models commonly used for dynamic simulations of metals. Here we apply the new technique to well-characterized tantalum material, allowing for a robust connection to other experimental techniques. Deformation localization can be a concern in large strain experiments, and to help inform future use of the experimental platform, we use simulations with a sub-zone treatment of shear banding to explore potential localization behavior. Here we develop and utilize an experimental configuration with improved isolation of strength effects that can be applied to an expanded range of materials.

42 ENGINEERING↗

DOE OSTI2025

Suppressing trapped-electron-mode-driven turbulence via optimization of three-dimensional shaping

Abstract Turbulent transport driven by trapped electron modes (TEMs) is believed to drive significant heat and particle transport in quasihelically symmetric stellarators. Two three-dimensionally-shaped magnetic configurations with suppressed TEM-driven turbulence were generated through optimization that targeted quasihelical symmetry and the available energy of trapped electrons. Initial equilibria have flux surface shapes with a helically rotating negative triangularity (NT) and positive triangularity (PT). In gyrokinetic simulations, TEMs are suppressed in the reduced-TEM NT and PT configurations, showing that NT does not have the same beneficial turbulence properties over PT as seen in tokamaks. Heat fluxes from TEMs are also suppressed. Without temperature gradients and with a strong density gradient, the most unstable modes at low k y were consistent with toroidal universal instabilities (UIs) in the NT case and slab UIs in the PT case. Nonlinear simulations show that UIs drive substantial heat flux in both the NT and PT configurations. A moderate increase in β halves the heat flux in the NT configuration, while suppressing the heat flux in the PT geometry. Based on the present work, future optimizations aimed at reducing electrostatic drift wave-driven turbulent transport will need to consider UIs if β is sufficiently small.

Duff, J. M. (ORCID:0000000153086694)↗

DOE OSTI2025

Resilient stellarator divertor characteristics in the Helically Symmetric eXperiment

Resilient divertor features connected to open chaotic edge structures in the Helically Symmetric eXperiment are investigated. For the first time, an expanded vessel wall was considered that would give space for implementation of a physical divertor target structure. The analysis was done for four different magnetic configurations with very different chaotic plasma edges. A resilient plasma wall interaction pattern was identified across all configurations. This manifests as qualitatively very similar footprint behavior across the different plasma equilibria. Overall, the resilient field lines of interest with high connection length L C lie within a helical band along the wall for all configurations. This resiliency can be used to identify the best location of a divertor. The details of the magnetic footprint’s resilient helical band is subject to specific field line structures which are linked to the penetration depth of field lines into the plasma and directly influence the heat and particle flux patterns. The differences arising from these details are characterized by introducing a new metric, the minimum radial connection min $(\delta_N)$ of a field line from the last closed flux surface. The relationship, namely the deviation from a scaling law, between min $(\delta_N)$ and L C of the field lines in the plasma edge field line behavior suggests that the field lines are associated with structures such as resonant islands, cantori, and turnstiles. This helps determine the relevant magnetic flux channels based on the radial location of these chaotic edge structures and the divertor target footprint. These details will need to be taken into account for resilient divertor design.

divertor↗

DOE OSTI2024

Towards accurate prediction of configurational disorder properties in materials using graph neural networks

Abstract The prediction of configurational disorder properties, such as configurational entropy and order-disorder phase transition temperature, of compound materials relies on efficient and accurate evaluations of configurational energies. Previous cluster expansion methods are not applicable to configurationally-complex material systems, including those with atomic distortions and long-range orders. In this work, we propose to leverage the versatile expressive capabilities of graph neural networks (GNNs) for efficient evaluations of configurational energies and present a workflow combining attention-based GNNs and Monte Carlo simulations to calculate the disorder properties. Using the dataset of face-centered tetragonal gold copper without and with local atomic distortions as an example, we demonstrate that the proposed data-driven framework enables the prediction of phase transition temperatures close to experimental values. We also elucidate that the variance of the energy deviations among configurations controls the prediction accuracy of disorder properties and can be used as the target loss function when training and selecting the GNN models. The work serves as a fundamental step toward a data-driven paradigm for the accelerated design of configurationally-complex functional material systems.

Chemistry↗

DOE OSTI2020

Computationally efficient optimization models for preliminary distillation column design and separation energy targeting

We propose versatile shortcut distillation column and separation energy targeting models that are well-suited for superstructure-based process synthesis. The models are based on a novel reformulation of the Underwood equations to address systems where the components that are present in the feed can vary due to zero flow rates of some components. Also, we propose valid constraints, resulting in a significant enhancement of the computational performance of the models. Furthermore, the proposed distillation column model can automatically identify adequate key components and the energy requirement of a desired separation task, while considering a wide range of types of separations including non-sharp/sloppy splits. Also, the proposed separation energy targeting model can be used to estimate an energy requirement target for the separation of a mixture without finding detail network configurations. Due to their versatility and computational efficiency, the proposed models can be readily used for and expand the scope of superstructure-based process synthesis approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Combinatorial optimization and spatial remodeling of CYPs to control product profile

Activating inert substrates is a challenge in nature and synthetic chemistry, but essential for creating functionally active molecules. In this work, we used a combinatorial optimization approach to assemble cytochrome P450 monooxygenases (CYPs) and reductases (CPRs) to achieve a target product profile. By creating 110 CYP-CPR pairs and iteratively screening different pairing libraries, we demonstrated a framework for establishing a CYP network that catalyzes six oxidation reactions at three different positions of a chemical scaffold. Target product titer was improved by remodeling endoplasmic reticulum (ER) size and spatially controlling the CYPs’ configuration on the ER. Out of 47 potential products that could be synthesized, 86% of the products synthesized by the optimized network was our target compound quillaic acid (QA), the aglycone backbone of many pharmaceutically important saponins, and fermentation achieved QA titer 2.23 g/L.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1987

Polarization effects on hard target calibration of lidar systems

The theory of hard target calibration of lidar backscatter data, including laboratory measurements of the pertinent target reflectance parameters, is extended to include the effects of polarization of the transmitted and received laser radiation. The bidirectional reflectance-distribution function model of reflectance is expanded to a 4 x 4 matrix allowing Mueller matrix and Stokes vector calculus to be employed. Target reflectance parameters for calibration of lidar backscatter data are derived for various lidar system polarization configurations from integrating sphere and monostatic reflectometer measurements. It is found that correct modeling of polarization effects is mandatory for accurate calibration of hard target reflectance parameters and, therefore, for accurate calibration of lidar backscatter data.

Kavaya, Michael J.↗

NASA NTRS2026

Performance Evaluation of Intravehicular Activity Spacesuit Without the Use of a Liquid Cooling Garment

The Orion Crew Survival Systems (OCSS) suit is equipped with safety technology that protects the crew during launch and re-entry and Intravehicular Activities (IVA). It was designed to be used with a Liquid Cooling Garment (LCG), an undergarment with tubes that circulate water to remove excess heat from a crew member. The objective of this study is to determine if the Modified Advanced Crew Escape Suit (MACES), which has very similar material, assembly, and pressure characteristics as the OCSS suit, can be used without the LCG to maintain the crew within their heat storage requirements where exceedances can lead to cognitive and physiological impairment. Testing was completed for both hot and cold environments where test subjects wore varying configurations of the MACES suit ensemble without the LCG. The tests were conducted in a temperature and humidity-controlled chamber with four test subjects ranging from extra small to large. Target metabolic rates were reached using an arm ergometer. To represent the different suit configurations seen in the concept of operations, the suit was tested with visor-down, visor-up, and without helmet and gloves. The test data was analyzed to determine how the environment, test subject size, metabolic rate, and suit configuration affected heat storage. Furthermore, the test data was used to correlate the METMAN model, a transient metabolic man program that simulates the heat transfer within a crew member’s body and from a crew member to the surrounding environment. The METMAN correlation showed good agreement between predicted heat storage and test data at the end of the test duration, with a coefficient of determination (R 2 ) value of 0.8999 for visor-down cases and R 2 of 0.8902 for visor-up and helmet off cases. A correlated METMAN model allows for the analysis and prediction of IVA suit performance without an LCG in additional scenarios.

Human Thermal Modeling↗

NASA NTRS2026

Performance Evaluation of Intravehicular Activity Spacesuit Without the Use of a Liquid Cooling Garment

The Orion Crew Survival Systems (OCSS) suit is equipped with safety technology that protects the crew during launch and re-entry and Intravehicular Activities (IVA). It was designed to be used with a Liquid Cooling Garment (LCG), an undergarment with tubes that circulate water to remove excess heat from a crew member. The objective of this study is to determine if the Modified Advanced Crew Escape Suit (MACES), which has very similar material, assembly, and pressure characteristics as the OCSS suit, can be used without the LCG to maintain the crew within their heat storage requirements where exceedances can lead to cognitive and physiological impairment. Testing was completed for both hot and cold environments where test subjects wore varying configurations of the MACES suit ensemble without the LCG. The tests were conducted in a temperature and humidity-controlled chamber with four test subjects ranging from extra small to large. Target metabolic rates were reached using an arm ergometer. To represent the different suit configurations seen in the concept of operations, the suit was tested with visor-down, visor-up, and without helmet and gloves. The test data was analyzed to determine how the environment, test subject size, metabolic rate, and suit configuration affected heat storage. Furthermore, the test data was used to correlate the METMAN model, a transient metabolic man program that simulates the heat transfer within a crew member’s body and from a crew member to the surrounding environment. The METMAN correlation showed good agreement between predicted heat storage and test data at the end of the test duration, with a coefficient of determination (R 2 ) value of 0.8999 for visor-down cases and R 2 of 0.8902 for visor-up and helmet off cases. A correlated METMAN model allows for the analysis and prediction of IVA suit performance without an LCG in additional scenarios.

Spacesuit↗

DOE OSTI2026

Search for the production of Higgs-portal scalar bosons in the NuMI beam using the MicroBooNE detector

We present the strongest experimental limits to date on the mixing angle, 𝜃, with which a new scalar particle, 𝑆, mixes with the Higgs field in the mass range 110 MeV < 𝑚 𝑆 <155 MeV. This result uses the MicroBooNE liquid argon time projection chamber to search for decays of these Higgs-portal scalar particles through the 𝑆 → 𝑒 + ⁢𝑒 − channel with the decays of kaons in the NuMI neutrino beam acting as the source of the scalar particles. The analysis uses an exposure of 2.01 × 10 21 protons on target of NuMI beam data including periods when the beam focusing system was configured to focus positively charged hadrons and separate periods when negatively charged hadrons were focused. The analysis searches for scalar particles produced from kaons decaying in flight in the beam’s decay volume and at rest in the target and absorber. At 𝑚 𝑆 =125 MeV (𝑚 𝑆 =150 MeV) we set a limit of 𝜃 < 3.19 ×10 −4 (𝜃 < 2.79 ×10 −4 ) at the 95% confidence level.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRSDate not supplied

NASA Small Engine Components Compressor Test Facility: High Efficiency Centrifugal Compressor Vaneless Diffuser and Transition Duct Configurations

The original vaned configuration of the High Efficiency Centrifugal Compressor (HECC) was developed with aggressive design targets to facilitate advancement of state-of-the-art technology in gas turbine compressors. This work documents modifications to the Small Engine Components Compressor Test Facility to support testing of the HECC vaneless diffuser and transition duct configurations, both of which are open geometries. These configurations were developed as follow-up studies to improve understanding of the differences between the predicted and actual performance of the original HECC vaned diffuser stage. Specifically, the vaneless diffuser was designed to provide the impeller with ideal exit conditions such that the impeller performance could be isolated from downstream stationary components, and the additively manufactured transition duct inlet configuration enables investigation into the effects of the inlet flow path on the stage performance. Features of note in the facility are active clearance control, bleed flow regulation, modular inlet configurations, and steady-state and fast-response instrumentation throughout the flow path. Details of the facility and instrumentation are presented as well as the baseline performance of the compressor stage. The geometry, performance, and detailed aerodynamic data have been made available to the public at https://storage.googleapis.com/heccdata/NASA-HECC-Data-Archive.zip.

centrifugal compressor↗

NASA NTRSDate not supplied

NASA Small Engine Components Compressor Test Facility: High Efficiency Centrifugal Compressor Vaneless Diffuser and Transition Duct Configurations

The original vaned configuration of the High Efficiency Centrifugal Compressor (HECC) was developed with aggressive design targets to facilitate advancement of state-of-the-art technology in gas turbine compressors. This work documents modifications to the Small Engine Components Compressor Test Facility to support testing of the HECC vaneless diffuser and transition duct configurations, both of which are open geometries. These configurations were developed as follow-up studies to improve understanding of the differences between the predicted and actual performance of the original HECC vaned diffuser stage. Specifically, the vaneless diffuser was designed to provide the impeller with ideal exit conditions such that the impeller performance could be isolated from downstream stationary components, and the additively manufactured transition duct inlet configuration enables investigation into the effects of the inlet flow path on the stage performance. Features of note in the facility are active clearance control, bleed flow regulation, modular inlet configurations, and steady-state and fast-response instrumentation throughout the flow path. Details of the facility and instrumentation are presented as well as the baseline performance of the compressor stage. The geometry, performance, and detailed aerodynamic data have been made available to the public at https://storage.googleapis.com/hecc-data/NASA-HECC-Data-Archive.zip.

centrifugal compressor↗

DOE OSTI2024

Proton Beam Window In Situ Neutronics Analysis for the Preliminary Design for the Second Target Station

These analyses provide estimates for the residual dose rates for various geometric configurations related to proton beam window (PBW) removal and replacement maintenance events. This information will be used to plan a remote handling strategy for the replacement and maintenance of the PBW. The 5 and 100 mrem/h dose rate contour lines are of specific interest as they classify radiation areas (between 5 and 100 mrem/h) and high radiation areas (>100 mrem/h).

43 PARTICLE ACCELERATORS↗

NASA NTRS2022

Laser-Guided Space Interferometer

The mirrors of astronomical interferometers need to be aligned within a fraction of a wavelength relative to one another. This would be especially challenging for optical instruments with mirrors separated by hundreds of meters flying in Earth’s orbit. However, in this work, we show that this alignment can be achieved by means of: (i) flying the mirror cluster in a particular orbital configuration; (ii) closing a coarse positioning loop using GNSS (Global Navigation Satellite System); and (iii) closing a fine wavefront-control loop using light from a laser guide star. The orbital configuration is designed to keep the mirrors passively pointing at the target star (up to a small orbital perturbation) while the interferometer cluster is orbiting and changing its baseline. The laser guide star would be flying in the same orbit but in the opposite direction. In medium- or high-Earth orbit, the interferometer would be able to observe a star for several hours per orbit. In this work, we analyzed the performance of an optical space interferometer consisting of nine 20 cm mirrors mounted on CubeSats and flying 3 km apart (together with a combiner and a laser guide star small satellite). This configuration supports a resolution of 0.04 milliarcseconds - an order of magnitude better than current ground-based interferometers. We estimate the performance of this system imaging stellar surfaces assuming perfect wavefront estimation and control.

Leonid Pogorelyuk↗

NASA NTRS1992

Applications of a direct/iterative design method to complex transonic configurations

The current study explores the use of an automated direct/iterative design method for the reduction of drag in transport configurations, including configurations with engine nacelles. The method requires the user to choose a proper target-pressure distribution and then develops a corresponding airfoil section. The method can be applied to two-dimensional airfoil sections or to three-dimensional wings. The three cases that are presented show successful application of the method for reducing drag from various sources. The first two cases demonstrate the use of the method to reduce induced drag by designing to an elliptic span-load distribution and to reduce wave drag by decreasing the shock strength for a given lift. In the second case, a body-mounted nacelle is added and the method is successfully used to eliminate increases in wing drag associated with the nacelle addition by designing to an arbitrary pressure distribution as a result of the redesigning of a wing in combination with a given underwing nacelle to clean-wing, target-pressure distributions. These cases illustrate several possible uses of the method for reducing different types of drag. The magnitude of the obtainable drag reduction varies with the constraints of the problem and the configuration to be modified.

Smith, Leigh Ann↗

DOE OSTI2024

Design of experiments to spectroscopically characterize radiation flow in stochastic media

Precise characterization of experimental radiation flow is required to validate the high energy density physics models, numerical methods, and codes that are used to simulate radiation-hydrodynamics phenomena such as thermal radiation transport in stochastic media. The Cassio code is used to simulate thermal radiation flow through inhomogeneous, stochastic-media-foam configurations containing optically thick clumps dispersed within an optically thin background aerogel. Cassio can model small inhomogeneous problems directly, but most problems require approximations to meet computer limitations on run-times and memory usage. Various examples of these approximations are methods that produce, in one calculation, an ensemble-averaged solution and associated standard deviation; reduced spatial dimensionality with approximate geometries; and full material homogenization with no geometric detail. Cassio simulations are used to design experiments at the OMEGA-60 Laser Facility that can measure the radiation flow using the spatially resolved COAX absorption spectroscopy diagnostic. The experimental platforms flow radiation through foam targets ranging from a background-only aerogel, to a single configuration of a specified stochastic medium, to a fully homogenized foam of the background and clump materials. Under constant total clump mass, larger clumps (here, larger than 10 μm diameter) will mix more slowly with the background such that the bulk radiation flow is faster than it would be in a fully homogenized material. The COAX platform can be used to infer temperature and density profiles in both the background material and clumps, simultaneously, and therefore to differentiate radiation flow in a range of stochastic and homogeneous media.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Effect of competition of spherical and deformed shells in quasifission of superheavy nuclei

Quasifission and fusion-fission represent the two most likely reaction outcomes to occur postcapture in collisions leading to superheavy nuclei. As such, understanding these mechanisms and how they relate to one another is key to understanding the intricate dynamics that drive the formation (or dissociation) of the nascent compound nuclei formed in fusion reactions. This understanding directly translates to a more informed picture of suitable reaction partners and can provide vital information for experimental efforts to study the physics and chemistry of superheavy elements. In this work we report results from time-dependent simulations of 48 Ca + 238 U and 50 Ti + 236 Th reactions at incident energies just above the Coulomb barrier with a focus on the quasifission process that prevent the formation of a fully equilibrated 286 Cn compound nucleus. We study these reactions systematically and consider a wide range of initial configurations to extract a robust estimate of primary fragment yields for the quasifission process. Multiple preferred exit channels are observed, with both spherical and deformed shell effects in the heavy and light fragments driving contributions to the production yields depending on the initial configuration of the system. Orientation effects of the deformed actinide targets are found to be a primary driver of which exit channels are populated. Here, the impact of moving away from a doubly magic projectile is explored with implications towards the reactions considered for current and future superheavy searches.

Gumbel, Richard [Michigan State University, East L↗

DOE OSTI2023

LH CO 2 MENT Colorado Project (Final Report)

The objective of Electricore’s pre-FEED project “LH CO 2 MENT COLORADO PROJECT” is to accelerate the implementation of a 1.5 million tonnes per year (TPY), and first-of-a-kind (FOAK) at world scale, Svante VeloxoTherm™ carbon capture plant. This project represents a quantum leap to a large-scale facility that will launch Svante’s carbon capture technology into the next era of accomplishments and market acceptance. By completing the Front-End Loading (FEL) Feasibility Study Report (FEL-2) for a fit-for-purpose design at the HOLCIM cement plant, located near Florence Colorado, USA, this technology can be proven as the future of large-scale deployment for carbon capture and storage. This carbon capture plant was designed with the goal of reaching a target of near Net Zero Emissions by capturing 90% of the carbon dioxide (CO 2 ) emissions from the HOLCIM cement plant and from the boiler which produces steam required to regenerate the adsorbent. Additionally, this project will be leveraging a renewable Power Purchase Agreement (PPA) using solar energy to acquire power at the target price of 0.04 $/kWh or less. In its current configuration CO 2 emissions from the HOLCIM cement plant is around 700 – 800 kg/ton of clinker produced. The proposed new carbon capture plant will allow a reduction of CO 2 emissions to about 100 kg/ton of clinker produced. The scope of work consists of the process design and capital & operating cost estimation (Class IV) for a total plant capacity of 4,750 TPD of pipeline grade CO 2 . The Svante VeloxoTherm™ technology is comprised of a Rotary Adsorption Machine (RAM) for intensified Thermal Swing Adsorption (TSA) using Structured Adsorbent Beds (SABs) and related Balance of Plant (BOP), including CO 2 compression. A business case (financial analysis) evaluation has been undertaken for the Owner’s management review. Recommendations on how best to proceed to the next stage of the project have been conveyed and are documented within this report. This analysis has relied on a detailed and comprehensive Project Financial Model, evaluating the Total Project IRR (after tax, unlevered, and including all forecast 45Q PTCs and 100% tax efficiency) – the project financial analysis (as opposed to standard TEA analysis) only considered a 12 year plant economic lifetime as a result of 45Q being the sole driver considered at this stage. The Total Project IRR was evaluated across a large number of potential scenarios. The evaluation demonstrated that if the 45Q PTD is increased to $85/MT for sequestration, there are a large number of feasible scenarios which demonstrate economic returns.

01 COAL, LIGNITE, AND PEAT↗