Search NASA⌕ Search

SEARCH · Search NASA

Results for “EVAPORATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

A constant heat flux model of the evaporating interline region

An approximate procedure is developed for determining the heat sink capability of an interline region (junction of vapor, evaporating thin film, and nonevaporating thin film), with consideration of the effect of resistance of the solid to heat transfer. The formulation is based on a simple one-dimensional constant heat flux model. The solution is directed toward a limiting case in which the thermal conductance of the solid is controlling. Since the value of the ideal liquid-vapor interfacial heat transfer coefficient is very large, conductance of the solid is found to dominate the overall heat transfer coefficient in the interline region after a small increase in film thickness.

Wayner, P. C., Jr.↗
NASA NTRS1978

Evaporative water loss in man in a gravity-free environment

Daily evaporative water losses (EWL) during the three Skylab missions were measured indirectly using mass and water-balance techniques. The mean daily values of EWL for the nine crew members who averaged 1 hr of daily exercise were: preflight 1,750 + or - 37 (SE) ml or 970 + or - 20 ml/sq m and inflight 1,560 + or - 26 ml or 860 + or - 14 ml/sq m. Although it was expected the EWL would increase in the hypobaric environment of Skylab, an average decrease from preflight sea-level conditions of 11% was measured. The results suggest that weightlessness decreased sweat losses during exercise and possibly reduced insensible skin losses. The weightlessness environment apparently promotes the formation of an observed sweat film on the skin surface during exercise by reducing convective flow and sweat drippage, resulting in high levels of skin wettedness that favor sweat suppression.

Leach, C. S.↗
NASA NTRS1979

Evaporative cooling on a grooved surface

The transition point where water begins to accumulate on the surface during spray evaporative cooling was investigated experimentally to determine the temperatures and corresponding heat flux at which this transition occurs. Several pressure ranges were considered including one below the triple point of water. Additionally, the results using a grooved surface were compared to those using a smooth surface. It was determined that a grooved surface has no effect on the heat transfer.

Yoder, D.↗
NASA NTRS1979

A fundamental study of liquid spray evaporation at a heated surface

The influence of feedwater temperature and the influence of pulsing nozzle flow on the heat transfer characteristics in the spray evaporative cooling process were investigated. A commercial water circulation heater was installed in the feedwater line between the supply reservoir and the nozzle. A pass through the heater provided water at temperatures up to 50 C at the nozzle; higher temperatures were obtained by multiple heater passes. A thermocouple installed in the water line just upstream of the nozzle provided a measure of the feedwater temperature. Initial tests were run with belljar exhaust orifice number two which provided a pressure in a range about 7mm Hg abs. The feedwater temperature was heated to a temperature of 45 C. Results indicate that for a given system operating pressure, there is an upper limit on the feedwater temperature above which the spray will flash to vapor before hitting the surface to be cooled.

Wierum, F. A.↗
NASA NTRS1980

Development of a preprototype thermoelectric integrated membrane evaporation subsystem for water recovery

A three-man urine water recovery preprototype subsystem using a new concept to provide efficient potable water recovery from waste fluids on extended duration space flights has been designed, fabricated, and tested. Low power, compactness, and gravity insensitive operation are featured in this vacuum distillation subsystem that combines a hollow fiber polysulfone membrane evaporator with a thermoelectric heat pump. Application and integration of these key elements have solved problems inherent in previous reclamation subsystem designs. The hollow fiber elements provide positive liquid/gas phase control with no moving parts other than a waste liquid recirculation pump and a product water withdrawal pump. Tubular membranes provide structural integrity, improving on previous flat sheet membrane designs. A thermoelectric heat pump provides latent energy recovery.

Winkler, H. E.↗
NASA NTRS1980

Effect of UV irradiation on evaporated ZnS films

Evaporated ZnS films used as a component in reflectance enhancing or decreasing multilayer coatings for mirrors, transparent optical materials, and vacuum UV reflecting optics, are investigated with reference to the reflectance loss under UV irradiation and the formation of ZnO as a result of the decomposition of ZnS in the presence of oxygen. Reflectance measurements over a broad wavelength range reveal that the UV induced reflectance losses are generally restricted to wavelengths shorter than 4000 A and are most severe in the vacuum UV region. After 134 hr of UV exposure initially polycrystalline film of 150-200 A thick is completely converted to amorphous ZnO. The results demonstrate that caution should be exercised in employing ZnS as the outer layer in an optical coating system designed for use in the UV and vacuum UV regions.

Hass, G.↗
NASA NTRS1980

Effects of the Shuttle Orbiter fuselage and elevon on the molecular distribution of water vapor from the flash evaporator system

A concern has arisen regarding the emissive distribution of water molecules from the shuttle orbiter flash evaporator system (FES). The role of the orbiter fuselage and elevon in affecting molecular scattering distributions was nuclear. The effect of these components were evaluated. Molecular distributions of the water vapor effluents from the FE were measured. These data were compared with analytically predicted values and the resulting implications were calculated.

Richmond, R. G.↗
NASA NTRS1981

Evaporated As2S3 Luneburg lenses for LiNbO3:Ti optical waveguides

Luneburg lenses of good quality were formed on high index optical waveguides by evaporation of arsenic trisulfide glass through simple masks. Using only two thin circular aperture masks, lenses with focal spots of a few times the diffraction limited width at f/4 were obtained. These lenses were designed for and tested at both visible (633 nm) and infrared wavelengths. Procedures for the design, fabrication, and testing of lenses of this type are described.

Busch, J. R.↗
NASA NTRS1977

Analysis of evaporative water loss in the Skylab astronauts

Daily evaporative water losses (EWL) during the three Skylab missions were measured using the indirect mass and water balance techniques. A mean inflight EWL of 860 ml/day-m 2 was obtained for nine men who averaged one hour of daily exercise. Although it was expected the EWL would increase in the hypobaric environment of Skylab (1/3 atmosphere), an average decrease from preflight sea level conditions of 11 percent was measured. The results suggest that weightlessness may have been a factor in modifying EWL primarily by decreasing sweat losses during exercise and possibly by reducing insensible skin losses as well. The weightless environment apparently promotes the formation of a sweat film on the skin surface both directly, by reducing heat and mass convective flow and sweat drippage, and perhaps indirectly by inducing measurable biochemical changes resulting in high initial sweating rates. It is proposed that these high levels of skin wettedness favor sweat suppression by a previously described mechanism.

Leonard, J. I.↗
NASA NTRS1982

A study of the initial oxidation of evaporated thin films of aluminum by AES, ELS, and ESD

The room temperature, low pressure, oxidation of evaporated aluminum thin films has been studied by AES, ELS, and ESD. ESD was the most sensitive of the three methods to characterize a clean aluminum surface. Two oxidation stages were distinguished in the 0-3000 L oxygen exposure range. Between 0 and 50 L, the chemisorption of oxygen atoms was characterized by a fast decrease of the 67 eV AES Al peak and the 10 eV surface plasmon peak, and by a simultaneous increase of the oxygen AES and ESD signals. After 50 L, a change in slope in all AES and ESD signal variations was attributed to the slow growth of a thin layer of aluminum oxide, which after 3000 L was still only a few angstroms thick.

Bujor, M.↗
NASA NTRS1984

Evaporation Tower With Prill Nozzles

Tower more efficient than conventional evaporation equipment. Liquids such as milk and fruit juice concentrated by passing them through tiny nozzle to form droplets, then allowing droplets to fall through evacuated tower with cooled walls.

Du Fresne, E. R.↗
NASA NTRS1983

Structure of Evaporating and Combusting Sprays: Measurements and Predictions

Complete measurements of the structure of nonevaporating, evaporating and combusting sprays for sufficiently well defined boundary conditions to allow evaluation of models of these processes were obtained. The development of rational design methods for aircraft combustion chambers and other devices involving spray combustion were investigated. Three methods for treating the discrete phase are being considered: a locally homogeneous flow (LHF) model, a deterministic separated flow (DSF) model, and a stochastic separated flow (SSF) model. The main properties of these models are summarized.

Shuen, J. S.↗
NASA NTRS1982

Shuttle orbiter flash evaporator operational flight test performance

The Flash evaporator System (FES is part of the Shuttle Orbiter Active Thermal Control Subsystem. The FES provides total heat rejection for the vehicle Freon Coolant Loops during ascent and entry and supplementary heat rejection during orbital mission phases. This paper reviews the performance of the FES during the first two Shuttle orbital missions (STS-1 and STS-2). A comparison of actual mission performance against design requirements is presented. Mission profiles (including Freon inlet temperature and feedwater pressure transients), control temperature, and heat load variations are evaluated. Anomalies that occurred during STS-2 are discussed along with the procedures conducted, both in-flight and post-flight, to isolate the causes. Finally, the causes of the anomalies and resulting corrective action taken for STS-3 and subsequent flights are presented.

Nason, J. R.↗
NASA NTRS1985

Sintered Lining for Heat-Pipe Evaporator

Hotspots eliminated by lining inner wall. Distribution of heat transfer liquid in heat-pipe evaporator improved by lining inner wall with layer of sintered metal. Sintered layer takes place of layer of screen wick formerly sintered or bonded to wall. Since sintered layer always full of liquid, no hotspot of type that previously arose where former screen wick did not fit properly against wall.

Ernst, D. M.↗
NASA NTRS1984

A theoretical and experimental study of turbulent evaporating sprays

Measurements and analysis limited to the dilute portions of turbulent evaporating sprays, injected into a still air environment were completed. Mean and fluctuating velocities and Reynolds stress were measured in the continuous phase. Liquid phase measurements included liquid mass fluxes, drop sizes and drop size and velocity correlation. Initial conditions needed for model evaluation were measured at a location as close to the injector exit as possible. The test sprays showed significant effects of slip and turbulent dispersion of the discrete phase. The measurements were used to evaluate three typical models of these processes: (1) a locally homogeneous flow (LHF) model, where slip between the phases were neglected; (2) a deterministic separated flow (DSF) model, where slip was considered but effects of drop dispersion by turbulence were ignored; and (3) a stochastic separated flow (SSF) model, where effects of interphase slip and turbulent dispersion were considered using random-walk computations for drop motion. For all three models, a k-epsilon model as used to find the properties of the continuous phase. The LHF and DSF models did not provide very satisfactory predictions for the present measurements. In contrast, the SSF model performed reasonably well--with no modifications in the prescription of eddy properties from its original calibration.

Solomon, A. S. P.↗
NASA NTRS1984

Estimating net rainfall, evaporation and water storage of a bare soil from sequential L-band emissivities

A general method to use a time series of L-band emissivities as an input to a hydrological model for continuously monitoring the net rainfall and evaporation as well as the water content over the entire soil profile is proposed. The model requires a sufficiently accurate and general relation between soil emissivity and surface moisture content. A model which requires the soil hydraulic properties as an additional input, but does not need any weather data was developed. The method is shown to be numerically consistent.

Stroosnijder, L.↗
NASA NTRS1983

Evaporation and combustion of sprays

A description is provided of recent spray evaporation and combustion models, taking into account turbulent two- and three-dimensional spray processes found in furnaces, gas turbine combustors, and internal combustion engines. Within the class of spray models of interest, two major categories are distinguished, including locally homogeneous flow (LHF) models and separated flow (SF) models. SF models are of the greatest practical importance, but LHF models have distinct advantages in some cases. Attention is also given to recent progress on modeling interactions between drops and the flow in both dilute and dense sprays, involving sprays having low and high liquid volume fractions, respectively.

Faeth, G. M.↗
NASA NTRS1984

On the dynamics in evaporating cloud envelopes

Cowie and McKee (1977) have conducted an analytical study of the case of an isolated, spherical cloud at rest in an infinite, hot medium. The present investigation is concerned with the theoretical model considered by Cowie and McKee for a thermally evaporating cloud. An analysis is conducted under the same conditions of inviscid flow with temperature equipartition. The current analysis allows for a continuous change in the saturation of the conductivity, rather than abrupt transitions from a classical to a fully saturated regime and back again, as in the model employed by Cowie and McKee. By suitable variable transformations, the momentum and energy equations can be reduced in the inviscid limit to a single equation for the Mach number in terms of a modified radius, and the solutions represented in a phase plane. An analytic model for the structure of the shock layer is developed.

Giuliani, J. L., Jr.↗