Search NASA⌕ Search

SEARCH · Search NASA

Results for “cleaning methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

ATP as a biomarker of viable microorganisms in clean-room facilities

A new firefly luciferase bioluminescence assay method that differentiates free extracellular ATP (dead cells, etc.) from intracellular ATP (viable microbes) was used to determine the viable microbial cleanliness of various clean-room facilities. For comparison, samples were taken from both clean-rooms, where the air was filtered to remove particles >0.5 microm, and ordinary rooms with unfiltered air. The intracellular ATP was determined after enzymatically degrading the sample's free ATP. Also for comparison, cultivable microbial populations were counted on nutrient-rich trypticase soy agar (TSA) plates. Both the cultivable and ATP-based determinations indicate that the microbial burden was lower in clean-room facilities than in ordinary rooms. However, there was no direct correlation between the two sets of measurements because the two assays measured very different populations. A large fraction of the samples yielded no colony formers on TSA, but were positive for intracellular ATP. Subsequently, genomic DNA was isolated directly from selected samples and 16S rDNA fragments were cloned and sequenced, identifying nearest neighbors, many of which are known to be noncultivable in the media employed. It was concluded that viable microbial contamination can be reliably monitored by measurement of intracellular ATP, and that this method may be considered superior to cultivable colony counts due to its speed and its ability to report the presence of viable but noncultivable organisms. When the detection of nonviable microbes is of interest, the ATP assay can be supplemented with DNA analysis.

NASA Discipline Environmental Health↗

Selective non-oxidative dehydrogenation of ethanol to acetaldehyde and hydrogen on highly dilute NiCu alloys

The non-oxidative dehydrogenation of ethanol to acetaldehyde has long been considered as an important method to produce acetaldehyde and clean hydrogen gas. Although monometallic Cu nanoparticles have high activity in the non-oxidative dehydrogenation of ethanol, they quickly deactivate due to sintering of Cu. In this paper, we show that adding a small amount of Ni (Ni 0.01 Cu - Ni 0.001 Cu) into Cu to form highly dilute NiCu alloys dramatically increases the catalytic activity and increases their long-term stability. The kinetic studies show that the apparent activation energy decreases from ~70 kJ/mol over Cu to ~45 kJ/mol over the dilute NiCu alloys. The improved performance is observed both for nanoparticles and nanoporous NiCu alloys. The improvement in the long-term stability of the catalysts is attributed to the stabilization of Cu against sintering. Our characterization data show that Ni is atomically dispersed in Cu. The comparison of the catalytic performance of highly dilute alloy nanoparticles with nanoporous materials is useful to guide the design of novel mesoporous catalyst architectures for selective dehydrogenation reactions.

36 MATERIALS SCIENCE↗

Gate-Tunable Multiband Transport in ZrTe 5 Thin Devices

Interest in ZrTe 5 has been reinvigorated in recent years owing to its potential for hosting versatile topological electronic states and intriguing experimental discoveries. However, the mechanism of many of its unusual transport behaviors remains controversial: for example, the characteristic peak in the temperature-dependent resistivity and the anomalous Hall effect. Here, through employing a clean dry-transfer fabrication method in an inert environment, we successfully obtain high-quality ZrTe 5 thin devices that exhibit clear dual-gate tunability and ambipolar field effects. Such devices allow us to systematically study the resistance peak as well as the Hall effect at various doping densities and temperatures, revealing the contribution from electron–hole asymmetry and multiple-carrier transport. By comparing with theoretical calculations, we suggest a simplified semiclassical two-band model to explain the experimental observations. Finally, our work helps to resolve the longstanding puzzles on ZrTe 5 and could potentially pave the way for realizing novel topological states in the two-dimensional limit.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ozone-Activated Nanoporous Gold: A Stable and Storable Material for Catalytic Oxidation

We report a new method for facile and reproducible activation of nanoporous gold (npAu) materials of different forms for the catalytic selective partial oxidation of alcohols under ambient pressure, steady flow conditions. This method, based on the surface cleaning of npAu ingots with ozone to remove carbon documented in ultrahigh vacuum conditions, produces active npAu catalysts from ingots, foils, and shells by flowing an ozone/dioxygen mixture over the catalyst at 150 °C, followed by a temperature ramp from 50 to 150 °C in a flowing stream of 10% methanol and 20% oxygen. With this treatment, all three materials (ingots, foils, and shells) can be reproducibly activated, despite potential carbonaceous poisons resulting from their synthesis, and are highly active for the selective oxidation of primary alcohols over prolonged periods of time. The npAu materials activated in this manner exhibit catalytic behavior substantially different from those activated under different conditions previously reported. Once activated in this manner, they can be stored and easily reactivated by flow of reactant gases at 150 °C for a few hours. They possess improved selectivity for the coupling of higher alcohols, such as 1-butanol, and are not active for carbon monoxide oxidation. As a result, this ozone-treated npAu is a functionally new catalytic material.

36 MATERIALS SCIENCE↗

Developing a microwave-driven reactor for ammonia synthesis: insights into the unique challenges of microwave catalysis

Rapid development of new ammonia (NH 3 ) synthesis techniques that enable modular, intermittent production is essential to actualizing NH 3 's potential as a clean energy carrier, since contemporary methods are configured to centralized, continuous production methods with high emissions and are incompatible with renewable sources. Here, in this mission, microwave-driven catalysis is promising for its ability to enhance reaction kinetics and apply targeted heating for efficient energy use. However, owing to an incomplete understanding of the interaction between microwave fields and catalyst beds, the development of such microwave-catalysis systems remains underexplored and challenging. This paper investigates the 10× scale-up of a microwave-based NH 3 synthesis reactor using numerical and experimental approaches, achieving the largest reported microwave-driven NH 3 reactor to date. Results elucidate phenomena unique to microwave processes that are only predictable through numerical modeling, including how a catalyst's dielectric properties influence microwave field distribution by affecting penetration depth and how energy utilization can be poor even with sufficient attenuation. These dynamics change with scale, constrain reactor geometry, and potentially hamper performance. Nonetheless, we demonstrate a production rate of 56.6 g NH$_3$ per day, the highest reported NH 3 synthesis rate for laboratory-scale alternative techniques; correspondingly, the benchmark energy efficiency achieved in this paper (45.6 g NH$_3$ kW h -1 ) is the highest reported for such reactors of sufficient scale. Even with this exemplary energy efficiency, energy losses were found in excess of 50%, an issue resolvable through scale and reactor design. The efficiencies imparted by microwaves were key in these achievements, warranting further investigation toward development of microwave-driven NH 3 systems.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

In situ tuning and probing the ambipolar field effect on multiwall carbon nanotubes

We report a method of fabricating ultra-clean and hysteresis-free multiwall carbon nanotube field-effect transistors (CNFETs) inside the ultra-high vacuum transmission electron microscope equipped with a movable gold tip as a local gate. By tailoring the shell structure of the nanotube and varying the drain-source voltage (V{sub ds}), we can tune the electronic characteristic of a multiwall CNFET in situ. We have also found that the Schottky barriers of a multiwall CNFET are generated within the nanotube, but not at the nanotube/electrode contacts, and the barrier height has been derived. We have subsequently demonstrated the ambipolar characteristics of the CNFET with concurrent high-resolution imaging and local gating.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Overview of physics results from the ADITYA-U tokamak and future experiments

The ADITYA upgrade (ADITYA-U), a medium-sized (R 0 = 75 cm, a = 25 cm) conventional tokamak facility in India, has been consistently producing experiments findings by usingcircular and shaped-plasmas. Recognizing the plasma parameters aligning closely with the design parameters of circular limited plasmas, ADITYA-U shifted its focus toward exploring the operational regime for experimentation on saw-tooth and MHD phenomena. Moreover, ADITYA-U has made consistent advancements toward conducting preliminary plasma shaping experiments through the activation of top and bottom divertor coils utilizing hydrogen as well as deuterium fuels. Confinement is improved by a factor of ~1.5 in D 2 plasmas when compared to H 2 plasmas of ADITYA-U. Further, ADITYA-U operations emphasize preventing disruptions and runaway electrons (REs) to ensure safe operations for future fusion devices. Significant suppression of REs has been achieved in ADITYA-U with the application of pulsed localized vertical magnetic field (LVF) perturbation, thereby establishing the technique's independence from the tokamak device. The successful RE mitigation requires a critical threshold of LVF pulse magnitude, which is approximately 1% of the toroidal magnetic field, and a minimum duration of ~5 ms. Apart from this, several novel findings have been achieved in the ADITYA-U experiments, including the modification of sawtooth duration through gas-puff, the emergence of MHD-induced geodesic acoustic mode-like oscillations, the propagation of fast heat pulses induced by MHD activity, the control of RE dynamics through Gas-puffs, the propagation of pinch-driven cold-pulses, the transport and core accumulations of argon impurities, the mass dependency of plasma toroidal rotation and the detection of 'RICE' scaling, as well as the characterization of edge plasma using wall conditioning methods, such as glow discharge cleaning using a combination of Ar-H 2 mixture, localized wall cleaning by electron cyclotron resonant plasma, and the development of machine learning-based disruption predictions, will be discussed in this paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluation of Shear Strength Threshold of Concern for Retrieval of Interim-Stored K-Basin Sludge in the Hanford Site

K-Basin sludge will be recovered into the Sludge Transport and Storage Containers (STSCs) and will be stored in the T Plant for interim storage (at least 10 years). Long-term sludge storage tests conducted by Pacific Northwest National Laboratory show that high uranium content K Basin sludge can self-cement and form a strong sludge with a bulk shear strength of up to 65 kPa. Some of this sludge has "paste" and "chunks" with shear strengths of approximately 3~5 kPa and 380 ~ 770 kPa, respectively. High uranium content sludge samples subjected to hydrothermal testing (e.g., 185°C, 10 h) have been observed to form agglomerates with a shear strength up to 170 kPa. After interim storage at T Plant, the sludge in the STSCs will be mobilized by water jets impinging the sludge. The objective of the evaluation was to determine the range of sludge shear strength for which there is high confidence that a water-jet retrieval system can mobilize stored K-Basin sludge from STSCs. The shear strength at which the sludge can be retrieved is defined as the "shear strength threshold of concern." If the sludge shear strength is greater than the value of the shear strength threshold of concern, a water-jet retrieval system will be unlikely to mobilize the sludge up to the container’s walls. The shear strength threshold of concern can be compared with the range of possible shear strengths of K-Basin stored sludge to determine if the current post interim-storage, water-jet retrieval method is adequate. Fourteen effective cleaning radius (ECR) models were reviewed, and their validity was examined by applying them to Hanford 241-SY-101 and 241-AZ-101 Tanks to reproduce the measured ECR produced by the mixer pumps. The validation test identified that the Powell-3 and Crowe-2 ECR models are more accurate than other ECR models reviewed. These ECR models were used to address a question as to whether the effective cleaning radius of a water jet is sufficient or if it can be readily expanded to cover the range of possible shear strengths. These results will assist CH2M HILL Plateau Remediation Company (CHPRC) to establish the technical basis of the feasibility of the sludge retrieval and storage plan and to develop an adequate water jet system to retrieve the stored K-Basin sludge in the STSCs. The STSCs are 2:1 elliptical-head vessels, 58 inches in diameter and 105 inches tall. Each STSC will contain 0.5 to 2.1 m3 of settled sludge with the specific loading dependent upon sludge type.

43 PARTICLE ACCELERATORS↗

Prospecting for new physics in the Higgs and flavor sectors

We explore two directions in beyond the standard model physics: dark matter model building and probing new sources of CP violation. In dark matter model building, we consider two scenarios where the stability of dark matter derives from the flavor symmetries of the standard model. The first model contains a flavor singlet dark matter candidate whose couplings to the visible sector are proportional to the flavor breaking parameters. This leads to a metastable dark matter with TeV scale mediators. In the second model, we consider a fully gauged SU(3) 3 flavor model with a flavor triplet dark matter. Consequently, the dark matter multiplet is charged while the standard model fields are neutral under a remnant Z 3 which ensures dark matter stability. We show that a Dirac fermion dark matter with radiative splitting in the multiplet must have a mass in the range [0:5; 5] TeV in order to satisfy all experimental constraints. We then turn our attention to Higgs portal dark matter and investigate the possibility of obtaining bounds on the up, down, and strange quark Yukawa couplings. If Higgs portal dark matter is discovered, we find that direct detection rates are insensitive to vanishing light quark Yukawa couplings. We then review flavor models and give the expected enhancement or suppression of the Yukawa couplings in those models. Finally, in the last two chapters, we develop techniques for probing CP violation in the Higgs coupling to photons and in rare radiative decays of B mesons. While theoretically clean, we find that these methods are not practical with current and planned detectors. However, these techniques can be useful with a dedicated detector (e.g., a gaseous TPC). In the case of radiative B meson decay B 0 → (K* → Kππ) γ, the techniques we develop also allow the extraction of the photon polarization fraction which is sensitive to new physics contributions since, in the standard model, the right(left) handed polarization fraction is of O( Λ QCD =m b ) for $\bar{B}^{0}$(B 0 ) meson decays.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Development of Abrasion-Resistant Coating for Solar Reflective Films. Cooperative Research and Development Final Report, CRADA Number CRD-07-247

The purpose of this CRADA is to develop an abrasion-resistant coating, suitable for use on polymeric-based reflective films (e.g., the ReflecTech reflective film), that allows for improved scratch resistance and enables the use of aggressive cleaning techniques (e.g., direct contact methods like brushing) without damaging the specular reflectance properties of the reflective film.

47 OTHER INSTRUMENTATION↗

Messaging for Impact: Behavioral Science-Based Communication Strategies to Advance Energy Efficiency

Currently, five legal authorities require U.S. federal agencies to purchase energy-efficient products. However, compliance with these requirements has consistently been low (~55%). Recent surveys indicate that energy efficiency requirements are not communicated properly within federal agencies and energy-efficiency is not a top priority. In the constantly evolving energy industry, with many solutions for a clean energy future, effective communication methods are vital for widespread adoption of energy efficiency. We have been conducting experiments within the U.S. federal sector that test the effectiveness of messaging strategies developed by using behavioral science principles like loss aversion, framing, and herd behavior. This will identify effective communications methods that encourage energy efficiency adoption. In this study, we measure the effectiveness of different communication strategies by monitoring the web traffic of hyperlinks placed within our digital communications and outreach materials. To determine effective strategies that influence federal buyer behavior, the web traffic from subjects that received the behavioral science-based messaging (treatment group) is compared to that from subjects that received regular messaging (control group) for each of the strategies. This paper provides an overview of the behavioral science principles that we applied, data collection methods, and results of our analysis. Since the lack of effective communication of energy-efficiency policies is also a common problem in the private sector, the messaging strategies developed in this study can be applicable to other large private sector institutions

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Surface Finishing and Coating Parameters Impact on Additively Manufactured Binder-Jetted Steel–Bronze Composites

In this paper, electroless nickel plating is explored for the protection of binder-jetting-based additively manufactured (AM) composite materials. Electroless nickel plating was attempted on binder-jetted composites composed of stainless steel and bronze, resulting in differences in the physicochemical properties. We investigated the impact of surface finishing, plating solution chemistry, and plating parameters to attain a wide range of surface morphologies and roughness levels. We employed the Keyence microscope to quantitatively evaluate dramatically different surface properties before and after the coating of AM composites. Scanning electron microscopy revealed a wide range of microstructural properties in relation to each combination of surface finishing and coating parameters. We studied chempolishing, plasma cleaning, and organic cleaning as the surface preparation methods prior to coating. We found that surface preparation dictated the surface roughness. Taguchi statistical analysis was performed to investigate the relative strength of experimental factors and interconnectedness among process parameters to attain optimum coating qualities. The quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the roughness of the nickel-plated surface were 17.95%, 8.2%, 50.02%, and 13.21%, respectively. On the other hand, the quantitative impacts of phosphorous level, temperature, surface preparation, and time factor on the thickness of nickel plating were 35.12%, 41.40%, 3.87%, and 18.24%, respectively. The optimum combination of the factors’ level projected the lowest roughness of Ra at 7.76 µm. The optimum combination of the factors’ level projected the maximum achievable thickness of ~149 µm. This paper provides insights into coating process for overcoming the sensitivity of AM composites in hazardous application spaces via robust coating.

36 MATERIALS SCIENCE↗

First Sagittarius A* Event Horizon Telescope Results. III. Imaging of the Galactic Center Supermassive Black Hole

We present the first event-horizon-scale images and spatiotemporal analysis of Sgr A* taken with the Event Horizon Telescope in 2017 April at a wavelength of 1.3 mm. Imaging of Sgr A* has been conducted through surveys over a wide range of imaging assumptions using the classical CLEAN algorithm, regularized maximum likelihood methods, and a Bayesian posterior sampling method. Different prescriptions have been used to account for scattering effects by the interstellar medium toward the Galactic center. Mitigation of the rapid intraday variability that characterizes Sgr A* has been carried out through the addition of a “variability noise budget” in the observed visibilities, facilitating the reconstruction of static full-track images. Our static reconstructions of Sgr A* can be clustered into four representative morphologies that correspond to ring images with three different azimuthal brightness distributions and a small cluster that contains diverse nonring morphologies. Based on our extensive analysis of the effects of sparse (u,v)-coverage, source variability, and interstellar scattering, as well as studies of simulated visibility data, we conclude that the Event Horizon Telescope Sgr A* data show compelling evidence for an image that is dominated by a bright ring of emission with a ring diameter of ∼50 μas, consistent with the expected “shadow” of a 4 × 10$^{6}$ M $_{⊙}$ black hole in the Galactic center located at a distance of 8 kpc.

79 ASTRONOMY AND ASTROPHYSICS↗

Liquid and gaseous oxygen safety review

Materials used in oxygen systems and allowable oxygen environments are specified for each material. Design criteria, cleaning procedures and quality control methods are covered. Guidelines for protection against hazards involved with production, transportation, storage and use of oxygen are presented. Study also lists extensive references.

Lapin, A.↗

Liquid and gaseous oxygen safety review, volume 1

Materials used or contained in liquid and gaseous oxygen systems are analyzed for their compatibility; and areas of possible concern in oxygen systems are outlined. Design criteria, cleaning procedures, and quality control methods are covered in detail.

Lapin, A.↗

Contact Whiskers for Millimeter Wave Diodes

Several techniques are investigated for making short conical tips on wires (whiskers) used for contacting millimeter-wave Schottky diodes. One procedure, using a phosphoric and chromic acid etching solution (PCE), is found to give good results on 12 microns phosphor-bronze wires. Full cone angles of 60 degrees-80 degrees are consistently obtained, compared with the 15 degrees-20 degrees angles obtained with the widely used sodium hydroxide etch. Methods are also described for cleaning, increasing the tip diameter (i.e. blunting), gold plating, and testing the contact resistance of the whiskers. The effects of the whisker tip shape on the electrical resistance, inductance, and capacitance of the whiskers are studied, and examples given for typical sets of parameters.

Kerr, A. R.↗

AGARD three-dimensional aeroelastic configurations

The calculation of unsteady aerodynamic forces in the critical transonic speed regime is investigated. The development of such methods is be enhanced by the availability of a limited number of test cases for the comparison of competing methods. Test cases for five clean, isolated wings are presented. Wing geometric descriptions, airfoil coordinates, and suggested aerodynamic conditions for each are included.

Bland, S. R.↗