SEARCH · Search NASA

Results for “mechanical evaluation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Evaluation of Flaw Detection with SLDV Methods Before/After Mechanical Patch

This report provides a summary of the testing and the experiments to evaluate the utility of laser ultrasonic testing (UT) in detecting and characterizing defects on the surface of steel plates before and after the application of an engineered composite patch for crack repair. Included are the detection and characterization of defects from a section of welded plate material taken from the Sandia National Laboratories’ full-size mockup of a spent nuclear fuel (SNF) dry storage canister which had been pre-flawed and exposed to deliquescent sea salt conditions for 2 years. The information includes a review of previously reported metallurgical characterization, and new work on detailed surface characterization of the corrosion attack using laser UT.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Mechanical and Thermophysical properties of low enriched uranium-10wt% molybdenum rolled foils

In this study, low-enriched (~19.75% 235 U) U-10Mo(wt%) foils were evaluated for both mechanical and thermophysical properties to establish baseline characteristics prior to irradiation testing. Cast U-10Mo ingots were sequentially hot and cold rolled to two different final foil thicknesses, resulting in different levels of cold work being present in the finished foils. The mechanical response of the U-10Mo foils was evaluated in the temperature range of 293–623 K. Increasing test temperatures resulted in decreases of both yield and ultimate tensile strength. Comparison of results to earlier work performed on depleted U-10Mo rolled foils indicates that the material in this study has lower strength and increased ductility. However, a comparison of the two different foil thicknesses in this study found that they were nearly identical in yield and ultimate tensile strength, differing by only 10–20 MPa (<2%). Thermal conductivity was calculated from the measurements of specific heat, linear thermal expansion, and thermal diffusivity from 323 to 1273 K on both thicknesses of the foils. These data were approximately 5–10% lower than previously published data above 573 K and were similar to data for temperature ranges below 573 K. Differences are likely related to differences in grain size and/or impurity content and variation in fabrication history.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1995

Mechanical properties testing and results for thermal barrier coatings

Thermal Barrier Coatings (TBC's) provide a significant challenge in the evaluation of their mechanical properties in ways that provide data that is not specimen dependent. The paper reviews various developments of the principal author over the past several years for both plasma sprayed and physical vapor deposited (PVD) materials, as well as new data on the fatigue behavior of one material system. The test methods that have been employed address tensile and compressive modulus and ultimate strength, tensile and compressive fatigue strength, and interfacial strength. This testing is now underway. Property testing is especially difficult for TBC's owing to the limitation on fabrication thickness of the coating. Bending tests are not used as these tests do not provide sufficiently uniform states of strain for property evaluations. Test specimens with uniform states of axial stress have been devised for each material system. The results show that the material property results between various experimenters and experimental methods are not yet consistent. However, the results provide critical design data at a suitable level of accuracy for life prediction. The paper will review both tensile and compressive mechanical testing of uniaxial specimens showing property dependencies on material density and temperatures for both material systems. Successful test results for both tensile and compressive fatigue loadings will be given. The test data shows that the fatigue strength of the TBC's is highly stress dependent in both loading conditions and is likely to depend on stress range and not mean stress. The fatigue strength of the plasma sprayed TBC's appears to increase with elevated temperatures in a range of temperatures below the creep activation temperature for the materials. The plasma sprayed TBC materials have been confirmed to have cyclic hysteresis at all temperature levels down to room temperature. Limited failure analysis data for various specimens suggest that the failure modes are driven by normal geometric discontinuities in the TBC's.

Cruse, T. A.↗

NASA NTRS1990

Acousto-ultrasonic nondestructive evaluation of materials using laser beam generation and detection

The acousto-ultrasonic method has proven to be a most interesting technique for nondestructive evaluation of the mechanical properties of a variety of materials. Use of the technique or a modification thereof, has led to correlation of the associated stress wave factor with mechanical properties of both metals and composite materials. The method is applied to the nondestructive evaluation of selected fiber reinforced structural composites. For the first time, conventional piezoelectric transducers were replaced with laser beam ultrasonic generators and detectors. This modification permitted true non-contact acousto-ultrasonic measurements to be made, which yielded new information about the basic mechanisms involved as well as proved the feasibility of making such non-contact measurements on terrestrial and space structures and heat engine components. A state-of-the-art laser based acousto-ultrasonic system, incorporating a compact pulsed laser and a fiber-optic heterodyne interferometer, was delivered to the NASA Lewis Research Center.

Huber, Robert D.↗

NASA NTRS2001

Thresholds in Atmosphere-Soil Moisture Interactions: Results from Climate Model Studies

The potential predictability of the effects of warm season soil moisture anomalies over the central U.S. has been investigated using a series of GCM (Global Climate Model) experiments with the NCAR (National Center for Atmospheric Research) CCM3 (Community Climate Model version 3)/LSM (Land Surface Model). Three different types of experiments have been made, all starting in either March (representing precursor conditions) or June (conditions at the onset of the warm season): (1) 'anomaly' runs with large, exaggerated initial soil moisture reductions, aimed at evaluating the physical mechanisms by which soil moisture can affect the atmosphere; (2) 'predictability' runs aimed at evaluating whether typical soil moisture initial anomalies (indicative of year-to-year variability) can have a significant effect, and if so, for how long; (3) 'threshold' runs aimed at evaluating if a soil moisture anomaly must be of a specific size (i.e., a threshold crossed) before a significant impact on the atmosphere is seen. The 'anomaly' runs show a large, long-lasting response in soil moisture and also quantities such as surface temperature, sea level pressure, and precipitation; effects persist for at least a year. The 'predictability' runs, on the other hand, show very little impact of the initial soil moisture anomalies on the subsequent evolution of soil moisture and other atmospheric parameters; internal variability is most important, with the initial state of the atmosphere (representing remote effects such as SST anomalies) playing a more minor role. The 'threshold' runs, devised to help resolve the dichotomy in 'anomaly' and 'predictability' results, suggest that, at least in CCM3/LSM, the vertical profile of soil moisture is the most important factor, and that deep soil zone anomalies exert a more powerful, long-lasting effect than do anomalies in the near surface soil zone. We therefore suggest that soil moisture feedbacks may be more important in explaining prolonged decadal to century-long droughts evident in the historic and recent prehistoric records, but less important on a seasonal to interannual time-scale.

Oglesby, Robert J.↗

NASA NTRS2019

Characterization of 10-ft. Diameter Aluminum Alloy 2219 Integrally Stiffened Cylinders

The integrally stiffened cylinder (ISC) process, pioneered by NASA Langley Research Center, offers significant savings for launch vehicle structures. The ISC process is a near net shape, advanced manufacturing method for fabrication of single-piece, thin-walled barrels with internal longitudinal stiffeners, eliminating the need for longitudinal welding and machining. A cost-benefit analysis of the ISC process estimated a 50 % reduction in manufacturing costs and a 10% weight savings over the current multi-piece, machined and welded construction approach for stiffened barrels. In 2017, commercial-scale manufacturing trials were pursued, leading to a successful manufacturing demonstration of 10-ft. diameter ISC barrels fabricated from Al alloy 2219. Some cracking was observed in the stiffeners during fabrication. Optical metallography was performed to evaluate the as-formed microstructures to identify potential causes of cracking, along with mechanical testing to evaluate formability. Results revealed that cracking in the stiffeners was attributed to three likely causes: 1) large Al-Cu stringer particles, 2) stick-slip friction between the mandrel and ISC due to non-optimized lubrication, and 3) differences in material flow rate between the wall and stiffener locations. Testing to gauge formability revealed a significant decrease in ductility in the longitudinal directional for the as-formed condition, attributed to reduced ductility due to the large Al-Cu stringer particles. These results provide guidance toward materials and processing modifications for future ISC forming trials.

Tayon, Wesley A.↗

NASA NTRS1994

Matrix Fatigue Cracking Mechanisms of Alpha(2) TMC for Hypersonic Applications

The objective of this work was to understand matrix cracking mechanisms in a unidirectional alpha(sub 2) TMC in possible hypersonic applications. A (0)(sub 8) SCS-6/Ti-24Al-11Nb (at. percent) TMC was first subjected to a variety of simple isothermal and nonisothermal fatigue cycles to evaluate the damage mechanisms in simple conditions. A modified ascent mission cycle test was then performed to evaluate the combined effects of loading modes. This cycle mixes mechanical cycling at 150 and 483 C, sustained loads, and a slow thermal cycle to 815 C. At low cyclic stresses and strains more common in hypersonic applications, environment-assisted surface cracking limited fatigue resistance. This damage mechanism was most acute for out-of-phase nonisothermal cycles having extended cycle periods and the ascent mission cycle. A simple linear fraction damage model was employed to help understand this damage mechanism. Time-dependent environmental damage was found to strongly influence out-of-phase and mission life, with mechanical cycling damage due to the combination of external loading and CTE mismatch stresses playing a smaller role. The mechanical cycling and sustained loads in the mission cycle also had a smaller role.

Gabb, Timothy P.↗

DOE OSTI2021

Crack Stability in Breached Fuel

This report describes the fracture mechanics formalism to evaluate the stability of cracks in a fuel cladding. Recognized consensus-body linear elastic fracture mechanics (LEFM) was applied to identify the crack instability length, or the length at which unstable mechanical crack extension would occur, as a function of pellet swelling loading (radial strain and fraction conversion from UO 2 to U 3 O 8 ) at the local cracked cladding region for two postulated fracture toughness (K IC ) values of the cladding. The crack opening displacement (COD) and the crack opening area (COA) were also identified. This analysis informs evaluations for crack extension and the potential for pellet debris loss from the fuel rod for cases of pellet oxidation in dry storage canisters where inadvertent residual water may undergo radiolysis causing oxidizing conditions to pellets exposed to the canister environment through breached cladding.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Crack Stability in Breached Fuel

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1979

Feasibility study of silicon nitride protection of plastic encapsulated semiconductors

The application of low temperature silicon nitride protective layers on wire bonded integrated circuits mounted on lead frame assemblies is reported. An evaluation of the mechanical and electrical compatibility of both plasma nitride and photochemical silicon nitride (photonitride) passivations (parallel evaluations) of integrated circuits which were then encapsulated in plastic is described. Photonitride passivation is compatible with all wire bonded lead frame assemblies, with or without initial chip passivation. Plasma nitride passivation of lead frame assemblies is possible only if the chip is passivated before lead frame assembly. The survival rate after the environmental test sequence of devices with a coating of plasma nitride on the chip and a coating of either plasma nitride or photonitride over the assembled device is significantly greater than that of devices assembled with no nitride protective coating over either chip or lead frame.

Peters, J. W.↗

NASA NTRS1980

Fillers for improved graphite fiber retention by polymer matrix composites

This program was designed to develop technology for fabrication of graphite/epoxy composites containing selected boron and boron-containing fillers, determine the effects of the fillers on physical and mechanical properties of composites, and evaluate the effectiveness of the boron fillers for fiber retention when the composites are exposed to fire conditions followed by impact. Fillers evaluated were crystalline and amorphous boron, boron carbide, and aluminum boride. The fillers were evaluated by mixing with Narmco 5208 resin matrix at quantities up to 5%. Graphite composites were fabricated and evaluated with respect to their mechanical properties, resistance to humidity, and burning characteristics. Also, the mechanism by which the fillers prevented fiber release was studied.

Sheppard, C. H.↗

NASA NTRS2003

Fracture Evaluation of In-Situ Sensors for High Temperature Applications

The feasibility of fabricating an in-situ crack sensor for real-time detection of surface cracks propagating in engine components was evaluated using a computational fracture mechanics model. The in-situ sensor system would be required to: (1) Be capable of sustaining normal function in a severe environment; (2) Transmit a signal if a detected crack in the component was above a predetermined length, but below a critical length that would lead to failure; (3) Act neutrally upon the overall performance of the engine system and not interfere with the engine maintenance operations. In this work, fracture mechanics methodologies are used to identify the requirements for an in-situ sensor system that could withstand the engine operating environment, foreign object damage, and minimally degrade engine performance. A computational fracture mechanics model was developed to evaluate the feasibility of fabricating an in-situ crack sensor for real-time damage propagation detection in engine components.

Forth, Scott C.↗

NASA NTRS2006

Frictional Ignition Testing of Composite Materials

The space flight community has been investigating lightweight composite materials for use in propellant tanks for both liquid and gaseous oxygen for space flight vehicles. The use of these materials presents some risks pertaining to ignition and burning hazards in the presence of oxygen. Through hazard analysis process, some ignition mechanisms have been identified as being potentially credible. One of the ignition mechanisms was reciprocal friction; however, test data do not exist that could be used to clear or fail these types of materials as "oxygen compatible" for the reciprocal friction ignition mechanism. Therefore, testing was performed at White Sands Test Facility (WSTF) to provide data to evaluate this ignition mechanism. This paper presents the test system, approach, data results, and findings of the reciprocal friction testing performed on composite sample materials being considered for propellant tanks.

Peralta, Steve↗

NASA NTRSDate not supplied

ACO Dust Mitigation for Flexible Solar Arrays (DMFlex)

• Announcement of Collaborative Opportunity (ACO) with SSLMaxar • Purpose: • Evaluate blanket solar arrays with mechanical actuation for dust removal • Evaluate vibratory shaking and electrostatic methods for efficacy in simulated lunar environment • Goal is to develop dust mitigation for solar arrays • To maintain solar array operational capability over time • Avoid replacement costs • Extend mission durations

solar arrays↗

DOE OSTI2025

Electricity Markets and Long-Duration Energy Storage: A Survey of Grid Services and Revenue Streams

Purpose of Review Long Duration Energy Storage (LDES) is increasingly viewed as a potential resource for providing grid services that enhance the stability and flexibility of electricity systems. While some LDES services are integrated into existing market frameworks, traditional mechanisms may not fully account for their operational characteristics, potentially leading to undervaluation. Within this context, this paper reviews the literature and industry practices to assess potential grid services for LDES, evaluates existing compensation mechanisms, and identifies challenges to full market integration. Recent Findings We first review existing literature and identify key grid services unique to LDES, including enhancing grid resilience during extreme weather events, enabling long-term energy shifting, and providing flexible and firm energy in systems with limited dispatchable resources. Here, we also review how LDES services are compensated in current market frameworks and the challenges associated with the full realization of LDES values. Additionally, we summarize market mechanisms for storage technologies across U.S. wholesale markets. We find that some markets are adjusting incentive structures, such as incorporating storage duration in capacity accreditation, to better align with system needs and LDES contributions to the grid. However, further refinements in capacity remuneration and dispatch timeframes may be needed for more effective realization of LDES value. Summary This review evaluates potential grid services for LDES, examines existing compensation mechanisms for LDES technologies, and identifies gaps between these mechanisms and LDES operational characteristics. The review concludes by outlining potential market enhancements for more effective LDES integration and articulating additional research needs to support its efficient participation in future power systems.

Flexible resources↗

NASA NTRS1988

Strategies for adding adaptive learning mechanisms to rule-based diagnostic expert systems

Rule-based diagnostic expert systems can be used to perform many of the diagnostic chores necessary in today's complex space systems. These expert systems typically take a set of symptoms as input and produce diagnostic advice as output. The primary objective of such expert systems is to provide accurate and comprehensive advice which can be used to help return the space system in question to nominal operation. The development and maintenance of diagnostic expert systems is time and labor intensive since the services of both knowledge engineer(s) and domain expert(s) are required. The use of adaptive learning mechanisms to increment evaluate and refine rules promises to reduce both time and labor costs associated with such systems. This paper describes the basic adaptive learning mechanisms of strengthening, weakening, generalization, discrimination, and discovery. Next basic strategies are discussed for adding these learning mechanisms to rule-based diagnostic expert systems. These strategies support the incremental evaluation and refinement of rules in the knowledge base by comparing the set of advice given by the expert system (A) with the correct diagnosis (C). Techniques are described for selecting those rules in the in the knowledge base which should participate in adaptive learning. The strategies presented may be used with a wide variety of learning algorithms. Further, these strategies are applicable to a large number of rule-based diagnostic expert systems. They may be used to provide either immediate or deferred updating of the knowledge base.

Stclair, D. C.↗

DOE OSTI2025

A Spectrochemical Series for Electron Spin Relaxation

Controlling the rate of electron spin relaxation in paramagnetic molecules is essential for contemporary applications in molecular magnetism and quantum information science. However, the physical mechanisms of spin relaxation remain incompletely understood, and new spectroscopic observables play an important role in evaluating spin dynamics mechanisms and structure–property relationships. Here, we use cryogenic magnetic circular dichroism (MCD) spectroscopy and pulse electron paramagnetic resonance (EPR) in tandem to examine the impact of ligand field (d–d) excited states on spin relaxation rates. We employ a broad scope of square-planar Cu(II) compounds with varying ligand field strength, including CuS 4 , CuN 4 , CuN 2 O 2 , and CuO 4 first coordination spheres. An unexpectedly strong correlation exists between spin relaxation rates and the average d–d excitation energy (R 2 = 0.97). The relaxation rate trends as the inverse 11th power of the excited-state energies, whereas simplified theoretical models predict only an inverse second power dependence. These experimental results directly implicate ligand field excited states as playing a critical role in the ground-state spin relaxation mechanism. Furthermore, ligand field strength is revealed to be a particularly powerful design principle for spin dynamics, enabling formation of a spectrochemical series for spin relaxation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Genetic algorithm optimization of a chemical kinetic mechanism for propane at engine relevant conditions

Propane has demonstrated significant potential for reductions in greenhouse gas and pollutant emissions in medium- and heavy-duty engine applications, but further improvements require accurate, compact, and scalable chemical kinetic mechanisms to design the next generation of propane fueled engines, particularly at the boosted operating conditions necessary to meet the power density demand of medium- and heavy-duty applications. In this work, six key chemical reactions were identified in a reduced mechanism with 70 species and 352 reactions through a sensitivity analysis performed at conditions typical of thermodynamic trajectories observed in a high compression ratio, long stroke engine operated on propane from throttled to boosted operating conditions. While the original mechanism was validated against rapid compression machine (RCM) data, it was found to overpredict experimental autoignition tendencies in 2-zone, 0-D SI engine simulations performed in Chemkin Pro. Subsequently, a genetic algorithm approach was used to optimize the six reaction rate parameters within established uncertainty bounds by performing RCM simulations and comparing to two independent sets of literature ignition delay times for propane, thus generating two new kinetic mechanisms. The first optimization achieved a mean absolute percent error (MPE) reduction in 2nd stage ignition delay of 61.4% in seven generations, while the second optimization utilized a newer experimental RCM dataset, and achieved MPE reduction of 56.7% in seven generations, and further marginal improvement to 57.8% reduction in 34 generations. Finally, the two mechanisms were then evaluated again in the 2-zone 0-D SI engine model in Chemkin Pro comparing typical mean and knocking cycle trajectories, and it was found that the second optimized mechanism provided better prediction of knock onset at the representative conditions evaluated in this work, particularly for higher load operating conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗