Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructural analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2012

Ceramographic Examinations of Irradiated AGR-1 Fuel Compacts

The AGR-1 experiment involved irradiating 72 cylindrical fuel compacts containing tri-structural isotropic (TRISO)-coated particles to a peak burnup of 19.5% fissions per initial metal atom with no in-pile failures observed out of almost 300,000 particles. Six irradiated AGR 1 fuel compacts were selected for microscopy that span a range of irradiation conditions (temperature, burnup, and fast fluence). These six compacts also included all four TRISO coating variations irradiated in the AGR experiment. The six compacts were cross-sectioned both transversely and longitudinally, mounted, ground, and polished after development of careful techniques for preserving particle structures against preparation damage. From 36 to 79 particles within each cross section were exposed near enough to midplane for optical microscopy of kernel, buffer, and coating behavior. The microstructural analysis focused on kernel swelling and porosity, buffer densification and fracture, debonding between the buffer and inner pyrolytic carbon (IPyC) layers, and fractures in the IPyC and SiC layers. Three basic particle morphologies were established according to the extent of bonding between the buffer and IPyC layers: complete debonding along the interface (Type A), no debonding along the interface (Type B), and partial debonding (Type AB). These basic morphologies were subdivided according to whether the buffer stayed intact or fractured. The resulting six characteristic morphologies were used to classify particles within each cross section, but no spatial patterns were clearly observed in any of the cross-sectional morphology maps. Although positions of particle types appeared random within compacts, examining a total of 931 classified particles allowed other relationships among morphological types to be established.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

Post-Service Examination of PWR Baffle Bolts, Part I. Examination and Test Plan

In support of extended service and current operations of the US nuclear reactor plants, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Light Water Reactor Sustainability (LWRS) Program, is coordinating with Ginna Nuclear Power Plant, The Westinghouse Electric Company, LLC, and ATI Consulting, the selective procurement of baffle bolts that were withdrawn from service in 2011 and currently stored on site at Ginna. The goal of this program is to perform detailed microstructural and mechanical property characterization of baffle former bolts following in-service exposures. This report outlines the selection criteria of the bolts and the techniques to be used in this study. The bolts available are the original alloy 347 steel fasteners used in holding the baffle plates to the baffle former structures within the lower portion of the pressurized water reactor vessel. Of the eleven possible bolts made available for this work, none were identified to have specific damage. The bolts, however, did show varying levels of breakaway torque required in their removal. The bolts available for this study varied in peak fluence (highest dose within the head of the bolt) between 9.9 and 27.8x10 21 n/cm 2 (E>1MeV). As no evidence for crack initiation was determined for the available bolts from preliminary visual examination, two bolts with the higher fluence values were selected for further post-irradiation examination. The two bolts showed different breakaway torque levels necessary in their removal. The information from these bolts will be integral to the LWRS program initiatives in evaluating end of life microstructure and properties. Furthermore, valuable data will be obtained that can be incorporated into model predictions of long-term irradiation behavior and compared to results obtained in high flux experimental reactor conditions. The two bolts selected for the ORNL study will be shipped to Westinghouse with bolts of interest to their collaborative efforts with the Electric Power Research Institute. Westinghouse will section the ORNL bolts into samples specified in this report and return them to ORNL. Samples will include bend bars for fracture toughness and crack propagation studies along with thin sections from which specimens for bend testing, subscale tensile and microstructural analysis can be obtained. Additional material from the high stress concentration region at the transition between the bolt head and shank will also be preserved to allow for further investigation of possible crack initiation sites.

42 ENGINEERING↗
DOE OSTI2015

Study of Compatibility of Stainless Steel Weld Joints with Liquid Sodium-Potassium Coolants for Fission Surface Power Reactors for Lunar and Space Applications

To make a manned mission to the surface of the moon or to Mars with any significant residence time, the power requirements will make a nuclear reactor the most feasible source of energy. To prepare for such a mission, NASA has teamed with the DOE to develop Fission Surface Power technology with the goal of developing viable options. The Fission Surface Power System (FSPS) recommended as the initial baseline design includes a liquid metal reactor and primary coolant system that transfers heat to two intermediate liquid metal heat transfer loops. Each intermediate loop transfers heat to two Stirling heat exchangers that each power two Stirling converters. Both the primary and the intermediate loops will use sodium-potassium (NaK) as the liquid metal coolant, and the primary loop will operate at temperatures exceeding 600°C. The alloy selected for the heat exchangers and piping is AISI Type 316L stainless steel. The extensive experience with NaK in breeder reactor programs and with earlier space reactors for unmanned missions lends considerable confidence in using NaK as a coolant in contact with stainless steel alloys. However, the microstructure, chemical segregation, and stress state of a weld leads to the potential for corrosion and cracking. Such failures have been experienced in NaK systems that have operated for times less than the eight year goal for the FSPS. For this reason, it was necessary to evaluate candidate weld techniques and expose welds to high-temperature, flowing NaK in a closed, closely controlled system. The goal of this project was to determine the optimum weld configuration for a NaK system that will withstand service for eight years under FSPS conditions. Since the most difficult weld to make and to evaluate is the tube to tube sheet weld in the intermediate heat exchangers, it was the focus of this research. A pumped loop of flowing NaK was fabricated for exposure of candidate weld specimens at temperatures of 600°C, the expected temperature within the intermediate heat exchangers. Since metal transfer from a high-temperature region to a cooler region is a predominant mode of corrosion in liquid metal systems, specimens were placed at zones in the loop at the above temperature to evaluate the effects of both alloy component leaching and metal deposition. Microstructural analysis was performed to evaluate weld performance on control weld specimens. The research was coordinated with Oak Ridge National Laboratory (ORNL) where most of the weld samples were prepared. In addition, ORNL participated in the loop operation to assist in keeping the testing relevant to the project and to take advantage of the extensive experience in liquid metal research at ORNL.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2015

Evaluation on the Effect of Composition on Radiation Hardening and Embrittlement in Model FeCrAl Alloys

This report details the findings of post-radiation mechanical testing and microstructural characterization performed on a series of model and commercial FeCrAl alloys to assist with the development of a cladding technology with enhanced accident tolerance. The samples investigated include model alloys with simple ferritic grain structure and two commercial alloys with minor solute additions. These samples were irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) up to nominal doses of 7.0 dpa near or at Light Water Reactor (LWR) relevant temperatures (300-400 C). Characterization included a suite of techniques including small angle neutron scattering (SANS), atom probe tomography (APT), and transmission based electron microscopy techniques. Mechanical testing included tensile tests at room temperature on sub-sized tensile specimens. The goal of this work was to conduct detailed characterization and mechanical testing to begin establishing empirical and/or theoretical structure-property relationships for radiation-induced hardening and embrittlement in the FeCrAl alloy class. Development of such relationships will provide insight on the performance of FeCrAl alloys in an irradiation environment and will enable further development of the alloy class for applications within a LWR environment. A particular focus was made on establishing trends, including composition and radiation dose. The report highlights in detail the pertinent findings based on this work. This report shows that radiation hardening in the alloys is primarily composition dependent due to the phase separation in the high-Cr FeCrAl alloys. Other radiation induced/enhanced microstructural features were less dependent on composition and when observed at low number densities, were not a significant contributor to the observed mechanical responses. Pre-existing microstructure in the alloys was found to be important, with grain boundaries and pre-existing dislocation networks acting as defect sinks, resulting in variations in the observed microstructures after irradiation. Dose trends were also observed, with increasing radiation dose promoting changes in the size and number density of the Cr-rich α' precipitates. Based on the microstructural analysis, performed tensile testing, and prior knowledge from FeCr literature it was hypothesized that the formation of the Cr-rich α' precipitates could lead to significant radiation-induced embrittlement in the alloys, and this could be composition dependent, a result which would mirror the trends observed for radiation-induced hardening. Due to the limited database on embrittlement in the FeCrAl alloy class after irradiation, a series of radiation experiments have been implemented. The overarching point of view within this report is the radiation tolerance of FeCrAl is complex, with many mechanisms and factors to be considered at once. Further development of the FeCrAl alloy class for enhanced accident tolerant applications requires detailed, single (or at least limited) variable experiments to fully comprehend and predict the performance of this alloy in LWRs. This report has been submitted as fulfillment of milestone M2FT-15OR0202321 titled, Summary report on the effect of composition on the irradiation embrittlement of Gen 1 ATF FeCrAl for the Department of Energy Office of Nuclear Energy, Advanced Fuel Campaign of the Fuel Cycle R&D program.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Nanoindentation of Electropolished FeCrAl Alloy Welds

The present report summarizes Berkovich nanoindentation modulus and hardness measurements on two candidate FeCrAl alloys (C35M and C37M) on as-received (AR) and welded samples. In addition, spherical nanoindentation stress-strain measurements were performed on individual grains to provide further information and demonstrate the applicability of these protocols to mechanically characterizing welds in FeCrAl alloys. The indentation results are compared against the reported tensile properties for these alloys to provide relationships between nanoindentation and tensile tests and insight into weldsoftening for these FeCrAl alloys. Hardness measurements revealed weld-softening for both alloys in good agreement with tensile test results. C35M showed a larger reduction in hardness at the weld center from the AR material compared to C37M; this is also consistent with tensile tests. In general, nanohardness was shown to be a good predictor of tensile yield strength and ultimate tensile stress for FeCrAl alloys. Spherical nanoindentation measurements revealed that the fusion zone (FZ) + heat affected zone (HAZ) has a very low defect density typical of well-annealed metals as indicated by the frequent pop-in events. Spherical nanoindentation yield strength, Berkovich hardness, and tensile yield strength measurements on the welded material all show that the C37M welded material has a higher strength than C35M welded material. From the comparison of nanoindentation and tensile tests, EBSD microstructure analysis, and information on the processing history, it can be deduced that the primary driver for weld-softening is a change in the defect structure at the grain-scale between the AR and welded material. These measurements serve as baseline data for utilizing nanoindentation for studying the effects of radiation damage on these alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Development of New Heats of Advanced Ferritic/Martensitic Alloys

The Fuel Cycle Research and Development program is investigating methods of transmuting minor actinides in various fuel cycle options. To achieve this goal, new fuels and cladding materials must be developed and tested to high burnup levels (e.g. >20%) requiring cladding to withstand very high doses (greater than 200 dpa) while in contact with the coolant and the fuel. To develop and qualify materials to a total fluence greater than 200 dpa requires development of advanced alloys and irradiations in fast reactors to test these alloys. Recent results from testing numerous ferritic/martensitic steels at low temperatures suggest that improvements in low temperature radiation tolerance can be achieved through carefully controlling the nitrogen content in these alloys. Thus, four new heats of HT-9 were produced with controlled nitrogen content: two by Metalwerks and two by Sophisticated Alloys. Initial results on these new alloys are presented including microstructural analysis and hardness testing. Future testing will include irradiation testing with ions and in reactor.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Coiled Tube Gas Heaters For Nuclear Gas-Brayton Power Conversion

This project developed an alternative design for heat exchangers for application to heating supercritical carbon dioxide (S-CO 2 ) or air for power conversion. We have identified an annular coiled tube bundle configuration–where hot sodium enters tubes from multiple vertical inlet manifold pipes, flows in a spiral pattern radially inward and downward, and then exits into an equal number of vertical outlet manifold pipes–as a potentially attractive option. The S-CO 2 gas or air flows radially outward through the tube bundle. Coiled tube gas heaters (CTGHs) are expected to have excellent thermal shock, long-term thermal creep, in-service inspection, and reparability characteristics, compared to alternative options. CTGHs have significant commonality with modern nuclear steam generators. Extensive experience exists with the design, manufacture, operation, in-service inspection and maintenance of nuclear steam generators. The U.S. Nuclear Regulatory Commission also has extensive experience with regulatory guidance documented in NUREG 0800. CTGHs leverage this experience and manufacturing capability. The most important difference between steam generators and gas-Brayton cycles such as the S-CO 2 cycle is that the heat exchangers must operate with counter flow with high effectiveness to minimize the pinch-point temperature difference between the hot liquid coolant and the heated gas. S-CO 2 -cycle gas heaters also operate at sufficiently elevated temperatures that time dependent creep is important and allowable stresses are relatively low. Designing heat exchangers to operate in this regime requires configurations that minimize stresses and stress concentrations. The cylindrical tubes and cylindrical manifold pipes used in CTGHs are particularly effective geometries. The first major goal of this research project was to develop and experimentally validate a detailed, 3-D multi-phase (gas-solid-liquid) heat transport model for CTGHs, using methods similar to earlier UCB multi-scale models for PCHEs, which will enable optimization of CTGH designs with respect to the number of manifold pipes, S-CO 2 and sodium circulating power, and other design parameters. CTGHs are relatively novel because the tubes loaded in compression as well as the manifold pipes which form the tube sheets. The second major goal of the experimental and modeling effort was to optimize the assembly and heat treatment of the tube-to-tubesheet joints, using a novel tapered joint configuration, and to develop diffusion-bonded joints with high shear strength and creep resistance, as has been done in other applications for tapered plugs. The project would also conduct creep testing of these tubesheet joints in pressurized furnaces under prototypical conditions of stress and temperature, however this was not feasible due to numerous hinderances. Detailed microstructural investigations was conducted on the diffusion bond interface, while the bond strength was evaluated by tensile testing. The mechanical testing quantified the overall strength of the bond and measured the pull out force as well as long term behavior, which complemented the microstructural analysis and gave a complete understanding of the diffusion bond.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2018

Microstructural Characterization of FeCrAl C26M Tubes

The present report summarizes the initial nanoindentation characterization of a FeCrAl alloy, C26M. Microstructural analysis using electron backscatter diffraction showed a highly textured system with the axial surface favoring orientations near the [110] and the longitudinal surface near the [111]. A large spread of grain sizes was observed from a few μm’s to 100 μm with an average grain size of ~70 μm. Nanoindentation with a Berkovich tip measured a similar hardness and modulus of ~4.4 GPa and ~240 GPa on the two surfaces, respectively. Mounting specimens in epoxy was found to be the cause of a lower stiffness and, consequently, a lower hardness and modulus value. Spherical nanoindentation was measured on the longitudinal surface of the tube to determine the nanoindentation modulus and nanoindentation yield strength. Using a 10 μm tip, the measured modulus was ~220 GPa and the yield strength was ~1.4 GPa. Indentation with a 100 μm tip resulted in a measured modulus value of ~220 GPa and yield strength of ~1.1 GPa. Some early characterization of the differences in spherical nanoindentation response of the axial and longitudinal surfaces showed a small difference between the two, but a more detailed analysis with a stiffer mounting configuration is needed to draw conclusions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Gleeble Compression Tests on As-Cast Alloy 709 Samples

Compression tests were performed on as-cast Alloy 709 (heat 58776-3) using Gleeble ® 3500-GTC system at Oak Ridge National Laboratory (ORNL). The testing temperature range was 900 °C to 1200 °C and the nominal true strain rate range was 0.001/s to 40/s. The tested specimens were delivered to Argonne National Laboratory (ANL) for confirmatory microstructure analysis. The test data were provided to ANL for the construction of the processing map for Alloy 709.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Nanoindentation Characterization of FeCrAl C26M tubes

The present report summarizes the nanoindentation characterization of a FeCrAl alloy, C26M in both tube and bar form. Microstructural analysis on the tube using electron backscatter diffraction showed a textured system with the cross-section favoring orie ntations near the [110] and the tube surface near the [111]. The bar cross-section showed a texture with orientation favoring those near the [100]. A large amount of in-grain misorientation was observed in the tube specimen with very little in the bar, indicating cold-work from tube processing steps. Nanoindentation with a Berkovich tip measured a similar modulus for all specimens of ~220 GPa. The bar specimens had a hardness of ~3.9 GPa, significantly lower than the 4.8 GPa and 5.2 GPa for the tube cross-section and surface, respectively. Spherical nanoindentation was performed on all specimens and orientations. Indentation with a 100 μm tip resulted in a measured modulus value of ~220 GPa for all specimens, in agreement with the Berkovich indentation results. The nanoindentation yield strength for the bar was found to be ~0.8 - 0.9 GPa, nearly 0.5 GPa less than the C26M tube.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanisms of Retention and Transport of Fission Products in Virgin and Irradiated Nuclear Graphite

To fulfill the design and licensing requirements for advanced reactors, the U.S. Department of Energy (DOE) is specifically interested in targeted research to quantify the mechanisms of fission product transport and retention in graphitic grades that will likely be used in next-generation very/high temperature reactors, fluoride salt-cooled high temperature reactors and molten salt reactors. We have examined an integrated experimental-computational approach to determine the diffusivities of selected fission products – ruthenium (Ru) and silver (Ag) in five nuclear graphite grades – POCO AXF-5Q, POCO ZXF-5Q, PCEA, IG110, and NBG-18. Experimental investigation for diffusion of other fission products (iodine, cesium, and krypton) in graphite could not be carried out due to extreme evaporation due to high vapor pressure, despite several attempts incorporating various experimental schemes. Experimental investigation with irradiated graphite could not be carried out because necessary approval to transport irradiated graphite could not be obtained due to procedural reasons at ORNL and national policy change in UK. An effort was made to “produce” by ion sputtering, but it was discontinued because the outcome did not adequately represent irradiated graphite. Thin film and “cup-and-cap” methods were employed to deposit fission products, diffusion annealed were carried out in an argon atmosphere, and concentration profiles were determined by dynamic secondary ion mass spectroscopy depth profiling technique. Regardless of graphite type, anomalous diffusion behavior of Ru (i.e., lower than expected based on Arrhenius temperature dependence) at an intermediate temperature, around 600 to 700 °C, was observed. Diffusion behavior of silver on the other hand agreed well to the Arrhenius temperature dependence although the excessive evaporation of silver hampered the accurate determination of diffusivities at temperature higher than 900 °C. In general, silver was observed to diffuse faster than Ru in the temperature range compared from 500 to 900 °C, had consistently had higher pre-exponential factor corresponding to higher jump frequency. To understand the abnormal diffusional behavior of Ru in graphite in intermediate temperature range, a detailed microstructural analysis was carried out. Clustering of Ru into particles on the surface of graphite was observed around 700 °C corresponding to de-wetting and spheroidization. This change would influence the boundary condition of diffusion, although features of clustering was much smaller (<1 mm) than the SIMS raster size (120 x 120 mm). Raman spectroscopy also demonstrated that Raman peak intensity for Ru decreased significantly for samples annealed higher than 700 °C and presence of Ru in graphite altered the crystallinity of graphite. To further elucidate the abnormal diffusion behavior observed in intermediate temperature investigated, the vibrational properties of graphene, bilayer graphene and Kr atoms in bilayer graphene were investigated with molecular dynamics. Krypton, which is a fission product, was introduced between a bilayer graphene system to evaluate (i) whether the phonon dispersion curves change with high temperature in bilayer graphene (ii) whether the addition of Kr atoms between the bilayer introduces any significant change in the vibrational properties, and (iii) whether any change in the vibrational properties can be correlated to the diffusive behavior of Kr atoms. The results show that the Kr atoms indeed exhibit an anomalous diffusive behavior at 550°C. Phonon analysis shows that a few phonon frequencies are enhanced as much as 20 to 30 % with the addition of just 0.2 at.% Kr. So, this may explain the unexpected self-diffusivity of fission products.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Laser Surface Processing of Alloys for Corrosion Protection (Final Project Report of Marine Energy Seedling Project)

This is the final project report for the MHK Seedling project. The report describes use of laser surface processing (LSP) to modify the surface of test materials (Al, steel) and the corrosion testing performed on the resulting samples in different corrosion environments. Data shows that LSP improved the corrosion resistance of Al and steel used in this work relative to respective non-LSP samples. The data also showed that each material had a specific range of laser processing conditions where the beneficial effects of LSP (i.e. improvement in corrosion protection) were observed. Application of LSP to enable low-cost materials in marine environments, additional microstructural analysis and long-term testing are proposed to further develop this technology for marine renewable energy and systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Capability to Process and Characterize Uranium-Zirconium (U-Zr) and Uranium-Zirconium-Plutonium (U-Zr-Pu) Alloys

This work investigated co-reduction of anhydrous compounds of uranium, zirconium, and plutonium to produce uranium rich ternary nuclear fuel alloys. Metallothermic co-reduction is a novel method to produce all-metal nuclear fuels. Metal fuels offer thermal, fissility, compatibility, and security benefits over oxide fuels. Alloys of uranium–10% zirconium with plutonium contents of 0%, 2.5%, 5%, and 10% were produced, with yields of 60–85% of theoretical values in a traditional calciothermic bomb reduction apparatus. Microstructural analysis indicated transformation of uranium phase from gamma to beta and then alpha, in alternating lamellar plates typical of alpha phase uranium and delta phase uranium-zirconium, with zirconium and carbides at prior grain boundaries. Some of the analyses were inconclusive in their results and therefore require additional testing. Successful ternary co-reduction would simplify production of homogeneous feedstock and thereby streamline manufacture of homogeneous ternary metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Process Intensification for Nanostructure Aluminum Extrusions

A new technology called Shear Assisted Processing and Extrusion (ShAPE™), pioneered at the Pacific Northwest National Laboratory (PNNL), has the potential to revolutionize the US extrusion industry. Maturation of the ShAPE™ process would create a new cross cutting US manufacturing technology that advances three key the objectives within AMO; namely, nanomaterials processing, process intensification, and materials for extreme and harsh environments. PNNL and SCM Metals Products, Inc. (SCM), a division of Kymera International, will collaborate to mature the ShAPE™ extrusion process beyond TRL 3 to increase the likelihood of its adoption by industry. PNNL’s custom (one-of-a-kind in the world) ShAPE™ machine will be used to extrude round rods of high strength aluminum alloy feedstock powder provided by SCM. As proof-of-concept, PNNL has previously extruded 5 mm diameter rods with SCM aluminum alloy powder AL-12.4TM. This project aims to scale up the process to a diameter of 25 mm while retaining the excellent mechanical properties achieved for the 5 mm diameter rods. The degree of process intensification with ShAPE™ will also be estimated. The primary objectives of this project are as follows. 1) Fabricate 25 mm diameter nanostructured extrusions in bulk, directly from AL-12.4TM aluminum alloy powder without the need for canning, degassing, compaction, and other intermediate steps typical of powder metallurgy extrusion. 2) Achieve a microstructure with an ultrafine grained (UFG <1 µm) aluminum matrix having refined and homogenously distributed nanoscale second phases. 3) Show that the ram force can be significantly reduced compared to conventional powder metallurgy extrusion of the same material and estimate the extent of process intensification that may be possible with ShAPE™. 4) Demonstrate improved high-temperature mechanical properties compared to conventional extrusion of the same material. The following tasks will be undertaken to achieve these objectives. PNNL will develop the die set and process parameters necessary to fabricate Al-12.4TM extrusions with a 25 mm diameter. Microstructural analysis will be performed by PNNL while mechanical testing will be conducted by SCM. With information learned from the process development and characterization, PNNL will perform an estimate of the degree of process intensification that may be possible with ShAPE™.

42 ENGINEERING↗
DOE OSTI2024

Laser Powder Bed Fusion of Steels for Nuclear Applications

This report provides an update on laser powder bed fusion of steels for nuclear applications. This report is a Milestone 3 deliverable in FY2024, under work package CT-24AN130401 to support research and qualification activities supported by the Advanced Materials and Manufacturing Technologies (AMMT) program here at Argonne National Laboratory (ANL). Continuing from FY23, the focus of FY24 for ANL includes further optimization of process parameters for three alloys: A709, G91, G92. The work package also includes fabricating test samples to conduct a thorough microstructural analysis and perform preliminary mechanical testing. For the same, we have used CALPHAD-based thermodynamic kinetic modeling to optimize the experimental activities.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of Stable Solid Oxide Electrolysis Cells for Low-Cost Hydrogen Production

The project objective was to demonstrate a solid oxide cell-based steam electrolysis stack that exhibits robustness, reliability, endurance, hydrogen purity, and produces hydrogen at elevated pressure of 2 to 3 bar. Innovative materials and processing methods were evaluated to improve degradation characteristics. Performance improvement focused on nearly all layers involved in the cell and stack assembly. Primary attention was paid to zirconia-ceria interface resistance control via sintering optimization and decrease in degradation from the oxygen electrode by evaluating low strontium (Sr) or Sr-free composition for both the oxygen electrode and current collection layer. Stack robustness was addressed by validating redox tolerance of fuel electrode, confirming capability of cells to survive repeated thermal cycles, studying the effect of pressure on performance and degradation, evaluating the effect of contamination on fuel and oxygen electrode performance and degradation, and identifying mitigation strategies to improve performance. The characterization included evaluation of electrochemical performance and stability followed by microstructural analysis. At the cell level, performance and stability improvements were achieved by incorporating a Sr-free oxygen electrode and a denser oxygen electrode barrier layer. At the stack level, pressurized operation reduces demand on first stage compression, the redox tolerant fuel electrode mitigates risk from service interruptions, and improvements to interconnect coating alleviate chromium (Cr) contamination effects. The denser barrier layer was achieved by adding a sintering aid to the samaria-doped ceria (SDC) composition that reduced sintering temperature by 150 °C. The resulting density was on par with the baseline SDC barrier layer density and the lower sintering temperature resulted in less resistive phase formation during sintering. Button cell tests did not demonstrate a change in performance when exposed to silicon (Si) or manganese (Mn) impurities to the fuel electrode and Cr impurity to the oxygen electrode. More detailed study however is warranted. The project addressed SOEC performance and stability at the cell and stack levels through a systematic approach to known sources of degradation that were combined and tested in three stack tests using an electrolyte supported cell design to allow for evaluation of a variety of fuel and oxygen electrode compositions. STK-82 and STK-83 had identical compositions. STK-100 incorporated the best materials and processing variables developed under this and concurrent projects, and was tested at elevated pressure in steam electrolysis. • STK-82 recovered performance after redox and thermal cycling, demonstrating the robustness of the stack and seals. It exhibited stable performance in testing for 500 hours in SOEC mode, followed by 300 hours of cycling between SOEC and SOFC tests. Degradation during SOEC operation was 1.8 %/ 1,000 hours. • STK-83 generated hydrogen at >80% steam conversion, and oxygen above 98.5 % purity during pressurized operation. Both hydrogen and oxygen were generated at 3 barg pressure without the use of a pressure vessel. In addition to balanced pressure, electrolysis operation at 1 bar differential pressure across anode and cathode was also demonstrated to substantial the robustness of the cell and seal. • STK-100 measured at initial ambient pressure conditions showed an area specific resistance of 1.1 ohm-cm 2 , and STK-83 had 1.3 ohm-cm 2 .

08 HYDROGEN↗
DOE OSTI2024

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

2.5D HI Packaging of the Power Converter using TSV interposer.

Abstract: Advantages of the 2.5D HI (Heterogeneous Integration) electronics packaging of the power electronics compared to PCB packaging will be presented. Current 2.5D packaging effort using TSV (Through Silicon Via) will be presented in terms of fabrication, microstructural analysis, reliability, and thermal simulation.

Chung, Hyunim↗