Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase delays”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Lunar topography - Global determination by radar.

Previous methods used for two-dimensional radar mapping of the moon are contrasted with new techniques that add altitude information to the radar map. Delay-Doppler stereoscopy and delay-Doppler interferometry are shown to provide surface-height variations with higher accuracy and better global fidelity than has been possible previously. Sample results are presented for altitude contours on the moon as obtained with the Haystack and Westford radar systems of the Massachusetts Institute of Technology. An appendix describes the mathematical principles of delay-Doppler interferometry in determining the position of an arbitrary reflecting region of the lunar surface from measurements of the time delay, Doppler shift, and fringe phase of radar echoes from that region.

Shapiro, I. I.↗
NASA NTRS1983

High dynamic, low volume GPS receiver

A new GPS receiver concept and design are presented to meet the high dynamic and low volume requirements for range applications in missiles and drones. The receiver has the potential to satisfy all range requirements with one basic receiver, which has significant potential economic benefit over the alternate approach of using a family of receivers, each tailored for specific applications. The main new concept is to use approximate maximum likelihood estimates of pseudo range and range-rate, rather than tracking with carrier phase locked loops and code delay locked loops. Preliminary analysis indicates that receivers accelerating at 50 g or more can track with position errors due to acceleration of approximately 0.2 m/g, or 10 m at 50 g. Implementation is almost entirely digital to meet the low volume requirements.

Hurd, W. J.↗
NASA NTRS1989

DMSK Receiver For Mobile/Satellite Service

Receiver for 2.4-kbit/s differential minimum-shift keying (DMSK) and Gaussian minimum-shift keying(GMSK) suitable for communication between land-mobile stations via geostationary satellites. Operating on phase-shifted signal in 800-MHz band, in presence of fading and Doppler frequency shifts, receiver compact, makes efficient use of frequency spectrum, and wastes little power. Receiver design implemented in very-large-scale-integrated circuits. Basic DMSK receiver design relies on baseband rather than intermediate-frequency processing of in-phase and quadrature signal components because phase errors due to differential delays smaller at baseband.

Davarian, Faramaz↗
NASA NTRS1999

Artificial Gravity as a Countermeasure of Cardiovascular Deconditioning in Spinal Cord Injury

An essential item in the development of this project was the availability of the artificial gravity simulator (AGS). At the termination of that grant in 1994, the AGS was dismantled and transferred to NASA Johnson Space Center. It took over two years for the AGS to be re-assembled and re-certified for use. As a consequence of the non-availability of the AGS for two years, there was a considerable delay in implementing the various phases of the project. The subjects involved in the study were eight healthy able bodied subjects and twelve with spinal cord injury. After analysis of the data collected on these subjects, six of the healthy able bodied subjects and three of the sub ects with spinal cord injury were found to qualify for the study. This report gives the results of four subjects only, two healthy able bodied and two spinal cord injured subjects because the period of the grant (1 year) and its extension (1 year) expired before additional subjects could be studied. The principal objective of the study was to conduct a series of experiments to demonstrate the feasibility of utilizing artificial gravity to assist in the physical rehabilitation of persons with spinal cord injuries.

Cardus, David↗
NASA NTRS2011

Percussive Augmenter of Rotary Drills (PARoD)

A percussive augmenter is being developed and it is designed to add ultrasonic hammering to a conventional commercial rotary drill through an adapter using a piezoelectric actuator. The combination of ultrasonic hammering and rotation creates a drill that requires low power and low axial load while providing faster penetration than conventional rotary-only drills. These characteristics make percussive augmentation of rotary drills ideal for not only planetary exploration but commercial applications as well. The purpose of this internship was to produce, test, and optimize an augmenter that drives a 2 inch diameter bit. This task was part of the percussive augmenter's phase II of an ongoing contract and it involved increasing the capability of the .25 inch version of the augmenter prototype that was developed in phase I. Due to fabrication delays of the augmenter, an extensive part of the test effort was conducted using previous rotary and hammer drill prototypes. These tests focused on drilling deep over long periods of time to provide for effective stress test of the drill. Modifications were made to the drill, its components, and the testing procedure to achieve desired borehole depths. These results were used to start initial testing on the 2 inch augmenter and provide preliminary data on the augmenter's ability to significantly improve penetration rate over conventional rotary-only drills.

rotraty hammer↗
NASA NTRS1996

Deconvolution Approach to Carrier and Code Multipath Error Elimination in High Precision GPS

This paper proposes a novel technique based on the deconvolution approach of the simultaneous estimation and compensation of the multipath estimation errors in both the carrier phase lock and the code delay lock loops in GPS receivers. Simulation results are presented showing that the proposed GPS receiver algorithm achieves high precision in the range and differential range estimation in various GPS precision applications such as spacecraft attitude control, even in a relatively severe multipath environment.

GPS↗
DOE OSTI2021

System and method for inspecting parts using dynamic response function

A system and method for the non-destructive testing of additively manufactured parts. An input mechanism excites with an excitation force (e.g., a vibration) an additive manufacturing build structure, which includes a part on a build platform, to induce a dynamic response in the part. An output mechanism (e.g., a non-contact transducer) senses the induced dynamic response in the part. A processor determines and examines the relationship between the response and excitation to identify an indication of a defect in the part, and communicates an alert if the indication is identified. The processor may compare the phase, magnitude, coherence, or time delay of the relationship to a reference relationship and/or may compare the modal frequency or the modal damping to a reference to identify a deviation greater than a pre-established threshold.

Hartwig, Troy Juan↗
NASA NTRS2021

ATD-2 Phase 3 Benefits Mechanism

NASA has been developing and demonstrating a suite of decision support capabilities for integrated arrival, departure, and surface (IADS) operations in a metroplex environment. The effort is being made in three phases, under NASA’s Airspace Technology Demonstration 2 (ATD-2) sub-project, through a close partnership with the Federal Aviation Administration (FAA), air carriers, airport, and general aviation community. ATD-2 Phase 1 & 2 have successfully demonstrated new technologies developed to manage the IADS capabilities at a single airport. The Phase 3 builds upon Phases 1 and 2 by extending the capabilities to a Metroplex environment where multiple airports are interacting and competing for resources at the terminal boundary. This document describes the metrics used to inform the flight operators, Air Traffic Control (ATC) tower, FAA, and even broader aviation community about opportunities to reroute aircraft and the metrics used to assess the performance of the ATD-2 Phase 3 system including benefits. This document provides definitions and detailed calculation methods of identified Phase 3 benefit metrics such as OFF Delay Savings, IN Delay Savings, and Aggregate System-Wide Savings. This document also describes the mechanism to translate delay savings metrics into fuel and emissions savings.

ATD-2 Phase 3↗
DOE OSTI2022

Repurposing the θ (Al 2 Cu) phase to simultaneously increase the strength and ductility of an additively manufactured Al–Cu alloy

The Al–Cu–Mn–Zr (ACMZ) cast family of alloys offers unique properties and value propositions for higher strength, higher temperature lightweight components of future vehicles. Earlier research has demonstrated trade-offs in the selection of the alloy chemistry in which an increase in Cu content from 6 up to 9 wt% improves hot tear resistance but lowers ductility. However, a recent study has demonstrated that higher-Cu (9Cu) ACMZ fabricated with laser powder bed fusion additive manufacturing (AM) results in an increase in both ductility and strength when compared to as-aged microstructure of cast 9Cu alloys. The mechanisms of differing mechanical performance of the cast and AM ACMZ alloys are elucidated in the current paper through the utilization of in situ high energy x-ray diffraction (HEXRD) tensile testing wherein lattice strains of different phases are calculated and correlated to their stresses. The ACMZ alloys consisted of theta (θ) and theta prime (θ') phases (both Al 2 Cu in nominal composition) within an aluminum matrix. The larger micron-size θ phase which decorated the grain boundaries in 9Cu ACMZ cast alloys recorded small lattice strains, while the submicron, homogeneously distributed θ phase in the 9Cu ACMZ AM alloy recorded considerably higher lattice strains. The maximum stress reached in the θ phase for the cast 9Cu alloy was found to be ~280 MPa, which was lower than the AM 9Cu alloy which registered a maximum stress of ~1.4 GPa. These measurements indicate that delayed fracture of the finer intermetallic phases simultaneously improves the ductility and strength of AM 9Cu alloy relative to the cast 9Cu alloy, which exhibits early fracture of the larger intermetallic particles.

36 MATERIALS SCIENCE↗
NASA NTRS2012

An Inter-Comparison of Two Independent Site Test Interferometers Located in Goldstone, California: Initial Study Results

Site Test Interferometers (STIs) have been deployed at two different locations at the NASA Deep Space Network (DSN) tracking complex in Goldstone, California. An STI measures the difference in path length between a geostationary satellite and two antennas on the Earth, producing a measure of atmospheric phase fluctuations over spatial distances comparable to those between elements of possible microwave phased arrays. The purposes of the Goldstone STIs are to assess the suitability of Goldstone as an array site and to statistically characterize atmospheric induced delay fluctuations for application to future array scenarios.The two STI's are separated by 13 km across the Goldstone complex. Each instrument is composed of two small-diameter antennas and associated electronics separated by approx. 200 meters in a principally east-west configuration. The antennas continuously observe signals emitted by geo-stationary satellites and produce data that contain information on the phase difference between signals received by both antennas. The fluctuation in delay (or path length difference) statistics derived from these data sets can be used to infer power loss for particular array configurations.We report on a comparison of the root mean square (RMS) phase delay statistics estimated over 10-minute intervals between the two Goldstone STIs. We have achieved good statistical agreement between the data acquired from the two STIs, given that each instrument is observing different satellites, at different frequencies, over different baseline lengths, with very different implementations, and are located 13 km apart in widely separated terrain at different geodetic altitudes.

propagation↗
NASA NTRS1971

Decoder for delay-modulation coded data.

A decoding technique is described for the conversion of delay-modulated digital data to nonreturn to zero (NRZ) data. A potential time-phase ambiguity in reception and decoding of delay-modulated data is resolved in real time, through monitoring the data stream for a unique waveform inherent in delay-modulated data. Statistical backup is provided.

Lewin, J.↗
NASA NTRS1991

Comparative study of bolometric and non-bolometric switching elements for microwave phase shifters

The performance of semiconductor and high critical temperature superconductor switches is compared as they are used in delay-line-type microwave and millimeter-wave phase shifters. Such factors as their ratios of the off-to-on resistances, parasitic reactances, power consumption, speed, input-to-output isolation, ease of fabrication, and physical dimensions are compared. Owing to their almost infinite off-to-on resistance ratio and excellent input-to-output isolation, bolometric superconducting switches appear to be quite suitable for use in microwave phase shifters; their only drawbacks are their speed and size. The SUPERFET, a novel device whose operation is based on the electric field effect in high critical temperature ceramic superconductors is also discussed. Preliminary results indicate that the SUPERFET is fast and that it can be scaled; therefore, it can be fabricated with dimensions comparable to semiconductor field-effect transistors.

Tabib-Azar, Massood↗
NASA NTRS1991

Comparative study of bolometric and non-bolometric switching elements for microwave phase shifters

The performance of semiconductor and high critical temperature superconductor switches is compared as they are used in delay-line-type microwave and millimeter-wave phase shifters. Such factors as their ratios of the off-to-on resistances, parasitic reactances, power consumption, speed, input-to-output isolation, ease of fabrication, and physical dimensions are compared. Owing to their almost infinite off-to-on resistance ratio and excellent input-to-output isolation, bolometric superconducting switches appear to be quite suitable for use in microwave phase shifters; their only drawbacks are their speed and size. The SUPERFET, a novel device whose operation is based on the electric field effect in high critical temperature ceramic superconductors is also discussed. Preliminary results indicate that the SUPERFET is fast and that it can be scaled; therefore, it can be fabricated with dimensions comparable to semiconductor field-effect transistors.

Tabib-Azar, Massood↗
NASA NTRS1983

Delay line and mutual coupling considerations for MST radar antenna arrays

Basic antenna theory which states that the field radiated from an antenna array is equal to the sum of the currents flowing in each element of the array is discussed. The feedline distribution system guarantees the proper amplitude and phase of the current for each element of an array. The difference in electrical lengths of the feedlines to the elements has to equal the desired phase angle. The current for voltage delay in a transmission line is equal to the transmission line electrical length in only a few special cases, when the transmission line is terminated in its characteristic impedance or when the transmission line's electrical length is a multiple of 90 degrees.

Brosnahan, J. W.↗
NASA NTRS1999

Time-Delay Interferometry for Space-based Gravitational Wave Searches

Ground-based, equal-arm-length laser interferometers are being built to measure high-frequency astrophysical graviatational waves. Because of the arm-length equality, laser light experiences the same delay in each arm and thus phase or frequency noise from the laser itself precisely cancels at the photodetector.

gravitational wave searches time-delay interferome↗
NASA NTRS1986

Double reference pulsed phase locked loop

A double reference pulse phase locked loop is described which measures the phase shift between tone burst signals initially derived from the same periodic signal source (voltage controlled oscillator) and delayed by different amounts because of two different paths. A first path is from the transducer to the surface of a sample and back. A second path is from the transducer to the opposite surface and back. A first pulse phase locked loop including a phase detector and a phase shifter forces the tone burst signal delayed by the second path in phase quadrature with the periodic signal source. A second pulse phase locked loop including a second phase detector forces the tone burst signals delayed by the first path into phase quadrature with the phase shifted periodic signal source.

Heyman, J. S.↗
NASA NTRS1971

A circadian rhythm in optic nerve impulses from an isolated eye in darkness.

Study of the circadian rhythm of optic nerve potentials recorded from the isolated eye of the sea hare Aplysia. The optic nerve activity in constant conditions is found to be clearly circadian and to obey the circadian rule for diurnal animals. In addition, the period length depends on the in vitro culturing solution. In seawater it is about 22 hr, but in culture medium it is 27 hr. The rhythm can be completely phase-shifted in one trial if the phase of the LD 12:12 Zeitgeber is advanced or delayed 4 hr. The rhythm in one eye can be phase-shifted in vivo independently of the other eye and in vitro independently of the rest of the animal. Thus, in the animal, the eye oscillators are, at most, only slightly influenced by each other or by other oscillators in the animal.

Jacklet, J. W.↗
NASA NTRS1993

Earth-based measurement of lunar topography using delayed radar interferometry

Radar interferometry has been applied to radar mapping of the surface of Venus to resolve the ambiguity in the backscatter from the areas with the same delay-Doppler coordinates. For observations of the Moon these points are usually isolated by the small extent of the area illuminated by the radar beam so that interferometric techniques can be used to determine a third dimension to the location of the radar backscatter. Recent observations of Sinus Iridum (41.5 deg N, 31.0 deg W) using the Arecibo Observatory S-Band radar system (12.6 cm wavelength) in Apr. and Aug. 1992 have yielded a pair of images viewed with a very small 0.0420 deg difference in incidence angle. These images can be used as a delay interferometric pair and have been correlated to generate phase fringes that are related to topography. The spatial resolution of the images are 18 m in delay and 33 m in cross range (Doppler). The anticipated topographic resolution once the phase fringes have been unwrapped is approximately +/- 10 m.

Stacy, N. J. S.↗