Search NASA⌕ Search

SEARCH · Search NASA

Results for “pilot model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

An analysis of airline landing flare data based on flight and training simulator measurements

Landings by experienced airline pilots transitioning to the DC-10, performed in flight and on a simulator, were analyzed and compared using a pilot-in-the-loop model of the landing maneuver. By solving for the effective feedback gains and pilot compensation which described landing technique, it was possible to discern fundamental differences in pilot behavior between the actual aircraft and the simulator. These differences were then used to infer simulator fidelity in terms of specific deficiencies and to quantify the effectiveness of training on the simulator as compared to training in flight. While training on the simulator, pilots exhibited larger effective lag in commanding the flare. The inability to compensate adequately for this lag was associated with hard or inconsistent landings. To some degree this deficiency was carried into flight, thus resulting in a slightly different and inferior landing technique than exhibited by pilots trained exclusively on the actual aircraft.

Heffley, R. K.↗
NASA NTRS1989

A methodology for the assessment of manned flight simulator fidelity

A relatively simple analytical methodology for assessing the fidelity of manned flight simulators for specific vehicles and tasks is offered. The methodology is based upon an application of a structural model of the human pilot, including motion cue effects. In particular, predicted pilot/vehicle dynamic characteristics are obtained with and without simulator limitations. A procedure for selecting model parameters can be implemented, given a probable pilot control strategy. In analyzing a pair of piloting tasks for which flight and simulation data are available, the methodology correctly predicted the existence of simulator fidelity problems. The methodology permitted the analytical evaluation of a change in simulator characteristics and indicated that a major source of the fidelity problems was a visual time delay in the simulation.

Hess, Ronald A.↗
NASA NTRS2001

Theoretical Prediction of Microgravity Ignition Delay of Polymeric Fuels in Low Velocity Flows

A new flammability apparatus and protocol, FIST (Forced Flow Ignition and Flame Spread Test), is under development. Based on the LIFT (Lateral Ignition and Flame Spread Test) protocol, FIST better reflects the environments expected in spacebased facilities. The final objective of the FIST research is to provide NASA with a test methodology that complements the existing protocol and provides a more comprehensive assessment of material flammability of practical materials for space applications. Theoretical modeling, an extensive normal gravity data bank and a few validation space experiments will support the testing methodology. The objective of the work presented here is to predict the ignition delay and critical heat flux for ignition of solid fuels in microgravity at airflow velocities below those induced in normal gravity. This is achieved through the application of a numerical model previously developed of piloted ignition of solid polymeric materials exposed to an external radiant heat flux. The model predictions will provide quantitative results about ignition of practical materials in the limiting conditions expected in space facilities. Experimental data of surface temperature histories and ignition delay obtained in the KC-135 aircraft are used to determine the critical pyrolysate mass flux for ignition and this value is subsequently used to predict the ignition delay and the critical heat flux for ignition of the material. Surface temperature and piloted ignition delay calculations for Polymethylmethacrylate (PMMA) and a Polypropylene/Fiberglass (PP/GL) composite were conducted under both reduced and normal gravity conditions. It was found that ignition delay times are significantly shorter at velocities below those induced by natural convection.

Fernandez-Pello, A. C.↗
NASA NTRS1975

Problems, questions and results in the use of the BBN-model

A hierarchical structured control model was used to describe pilot performance in a multivariable control problem. The model is based on the assumption that a well trained operator optimized a quadratic optimization criterion. The model considers some special characteristics of the human operator as time delay, neuromuscular time lag, observation and motor noise and the ability to extract the first derivative of a displaced value. Numerical results of a simple human engineering example using the BBN model demonstrate the influence of the variation of different parameters on covariance matrices of the state and observation vectors.

Dey, D.↗
NASA NTRSDate not supplied

Training Airline Pilots for Improved Flight Path Monitoring: The Sensemaking Model Framework

The importance and benefit of improved monitoring is increasingly recognized. Improved training may be a valuable intervention. Our study (conducted 2019) assessed and trained airline First Officers on flight path monitoring skills. The exploratory study assessed monitoring pre-training in a simulator session that included monitoring challenges (8 or 7 events). A 1-hour interactive training followed, based on the Sensemaking Model of Monitoring; it presented concepts and examples using a slide deck, discussion, and simple activities. Post-training assessment used scenarios with analogous monitoring challenges (7 or 8 events) but a different setting. Performance showed significant and relatively consistent improvement. Training monitoring as sensemaking merits further investigation.

training↗
NASA NTRS1995

Helicopter Human Factors

Even under optimal conditions, helicopter flight is a most demanding form of human-machine interaction, imposing continuous manual, visual, communications, and mental demands on pilots. It is made even more challenging by small margins for error created by the close proximity of terrain in NOE flight and missions flown at night and in low visibility. Although technology advances have satisfied some current and proposed requirements, hardware solutions alone are not sufficient to ensure acceptable system performance and pilot workload. However, human factors data needed to improve the design and use of helicopters lag behind advances in sensor, display, and control technology. Thus, it is difficult for designers to consider human capabilities and limitations when making design decisions. This results in costly accidents, design mistakes, unrealistic mission requirements, excessive training costs, and challenge human adaptability. NASA, in collaboration with DOD, industry, and academia, has initiated a program of research to develop scientific data bases and design principles to improve the pilot/vehicle interface, optimize training time and cost, and maintain pilot workload and system performance at an acceptable level. Work performed at Ames, and by other research laboratories, will be reviewed to summarize the most critical helicopter human factors problems and the results of research that has been performed to: (1) Quantify/model pilots use of visual cues for vehicle control; (2) Improve pilots' performance with helmet displays of thermal imagery and night vision goggles for situation awareness and vehicle control; (3) Model the processes by which pilots encode maps and compare them to the visual scene to develop perceptually and cognitively compatible electronic map formats; (4) Evaluate the use of spatially localized auditory displays for geographical orientation, target localization, radio frequency separation; (5) Develop and flight test control/display concepts; (6) Quantify, model, predict, and improve pilots, workload-management strategies; and (7) Design computer-game trainers to reduce training time and cost.

Hart, Sandra G.↗
DOE OSTI2024

Modeling Approach for the Aluminum-clad Dry Storage Pilot using HFIR Fuel

To confirm that the dry storage of aluminum-clad research reactor spent nuclear fuel (ASNF) will remain within the safety envelope after applied drying schemes and that the resulting evolution of the gas space composition, temperature, and pressure conditions are understood, a dry storage pilot project is being established. The pilot will incorporate an instrumented lid for discrete interval or for on-demand gas composition and temperature monitoring of two DOE Standard Canisters (DSCs) loaded with three High Flux Isotope Reactor (HFIR) inner cores per DSC. Each DSC would be subjected to a separate alternative candidate drying scheme. Canisters will undergo 1 to 5 years of monitoring, including internal temperature and gas sampling to track pressure and composition changes. This report outlines the approach for modeling the ASNF-in-canister behavior in terms of evolving gas space conditions for the ASNF dry storage pilot using HFIR fuel. The ASNF has an adherent surface oxyhydroxide layer comprised of boehmite/bayerite that generates hydrogen when subjected to irradiation. Three-dimensional multi-physics computational fluid dynamics simulations will be executed to compute the thermal field within the DSC and provide inputs to a chemical model employed to compute pressure buildup as hydrogen is generated in the system. Implemented in Cantera, the chemical model solves gas phase and aluminum oxyhydroxide surface-mediated radiolysis reactions. Gas phase reactions are sourced from Wittman and Hanson (2015), whereas surface-mediated reactions are incorporated by fitting experimental data using an optimization algorithm (Abboud, 2023). Water radiolysis reactions from Wren and Ball (2001) are adopted with modifications as described in Abboud (2023c). Understanding the effect of the hydrogen buildup over time is important for long-term storage safety considerations. Modeling results will include the canister pressure, temperature, and composition evolution from the initial helium backfill with the addition of radiolytically-evolved chemical species (e.g., hydrogen and oxygen). The specific HFIR cores for the pilot program have not yet been selected, and the overall design is still in development. The CFD-chemical model used for this work will be based on prior models with necessary updates to allow for improved accuracy and efficiency. The experimental data obtained from the HFIR demonstration will be used to improve and validate the computational models to predict the ASNF-in-canister behavior.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1987

Space shuttle flying qualities and criteria assessment

Work accomplished under a series of study tasks for the Flying Qualities and Flight Control Systems Design Criteria Experiment (OFQ) of the Shuttle Orbiter Experiments Program (OEX) is summarized. The tasks involved review of applicability of existing flying quality and flight control system specification and criteria for the Shuttle; identification of potentially crucial flying quality deficiencies; dynamic modeling of the Shuttle Orbiter pilot/vehicle system in the terminal flight phases; devising a nonintrusive experimental program for extraction and identification of vehicle dynamics, pilot control strategy, and approach and landing performance metrics, and preparation of an OEX approach to produce a data archive and optimize use of the data to develop flying qualities for future space shuttle craft in general. Analytic modeling of the Orbiter's unconventional closed-loop dynamics in landing, modeling pilot control strategies, verification of vehicle dynamics and pilot control strategy from flight data, review of various existent or proposed aircraft flying quality parameters and criteria in comparison with the unique dynamic characteristics and control aspects of the Shuttle in landing; and finally a summary of conclusions and recommendations for developing flying quality criteria and design guides for future Shuttle craft.

Myers, T. T.↗
NASA NTRS1996

Piloted Parameter Identification Flight Test Maneuvers for Closed Loop Modeling of the F-18 High Alpha Research Vehicle (HARV)

Flight test maneuvers are specified for the F-18 High Alpha Research Vehicle (HARV). The maneuvers were designed for closed loop parameter identification purposes, specifically for longitudinal and lateral linear model parameter estimation at 5, 20, 30, 45, and 60 degrees angle of attack, using the NASA 1A control law. Each maneuver is to be realized by the pilot applying square wave inputs to specific pilot station controls. Maneuver descriptions and complete specifications of the time/amplitude points defining each input are included, along with plots of the input time histories.

Morelli, Eugene A.↗
NASA NTRS1982

Blockage and flow studies of a generalized test apparatus including various wing configurations in the Langley 7-inch Mach 7 Pilot Tunnel

A 1/12th scale model of the Curved Surface Test Apparatus (CSTA), which will be used to study aerothermal loads and evaluate Thermal Protection Systems (TPS) on a fuselage-type configuration in the Langley 8-Foot High Temperature Structures Tunnel (8 ft HTST), was tested in the Langley 7-Inch Mach 7 Pilot Tunnel. The purpose of the tests was to study the overall flow characteristics and define an envelope for testing the CSTA in the 8 ft HTST. Wings were tested on the scaled CSTA model to select a wing configuration with the most favorable characteristics for conducting TPS evaluations for curved and intersecting surfaces. The results indicate that the CSTA and selected wing configuration can be tested at angles of attack up to 15.5 and 10.5 degrees, respectively. The base pressure for both models was at the expected low level for most test conditions. Results generally indicate that the CSTA and wing configuration will provide a useful test bed for aerothermal pads and thermal structural concept evaluation over a broad range of flow conditions in the 8 ft HTST.

Albertson, C. W.↗
NASA NTRS2018

San Francisco Bar Pilot Fatigue Study

The purpose of this study was to evaluate the extent of fatigue among San Francisco Bar Pilots (Maritime Pilots) and its potential impact on safety, and to make recommendations concerning how the risk of fatigue could be managed. Information was gathered via a literature review, observations of Bar Pilots at work, surveys, a task analysis, and an analysis of dispatch records.The work of San Francisco Bar Pilots involves an unusual mix of activities and job demands. Their work calls for situational awareness, reasoning, communication, and perceptual abilities comparable to those required by airline pilots and air traffic controllers. Errors can have severe consequences for public safety and the environment, as well as significant financial costs. Fatigue is increasingly recognized as a hazard that must be managed by the transportation industry. The reduced sleep quality and quantity experienced by personnel who work at night, in conjunction with human circadian rhythms can lead to an operationally significant level of cognitive impairment. The cognitive impact of fatigue includes functions that are critical to safe maritime piloting, such as vigilance, judgment, reaction time and communication. The surveys distributed to Bar Pilots did not uncover evidence of widespread fatigue. The survey results also suggested that fatigue was not a major concern of Bar Pilots. Bar Pilots had overall low scores on the subjective fatigue measures used in the survey, and generally assessed the safety risk due to fatigue as low. Compared to air traffic controllers, Bar Pilots gave significantly lower ratings on questions concerning the prevalence and impact of fatigue. The application of fatigue modeling software to Bar Pilot dispatch records identified that in most cases, pilot's cognitive effectiveness was predicted to be acceptable during their duty periods. However, these results could not be verified with objective data.The study identified a number of fatigue issues that deserve attention. These include Bar Pilot work periods that frequently infringe on the circadian low, consecutive work periods without a significant break, consecutive periods of night work, unpredictable work schedules, start time variability, the potential for sleep inertia, and the number of pilots on the board at any given time.

fatigue↗
NASA NTRSDate not supplied

Development of Urban Air Mobility (UAM) Vehicles for Ease of Operation

To date the air transportation system has been developed with the in-cremental introduction of new technology and with highly experienced air transport pilots and air traffic controllers overseeing flight operations. Thus, we currently have one of the safest commercial aviation systems in the world. General Aviation (GA) in the United States, however, has not always followed the same cautious and monitored approach to implementation; consequently, the GA safety record does not meet the high standards of commercial aviation. Recently, a new system known as Urban Air Mobility (UAM), is attracting considerable interest and investment from industry and government agencies. UAM refers to a system of passenger and small-cargo air transportation vehicles within an urban area with the goal of reducing the number of times we need to use our cars, thus improving urban traffic by moving people and cargo from crowded single pas-senger vehicles on our roads to personal and on-demand air vehicles. These UAM vehicles will be small and based on electric, Vertical-Take-Off-and-Landing (eV-TOL) systems. A significant component of UAM is offloading of flight-man-agement responsibilities from human pilots to newly-developed autonomy. Cur-rently, over 100 UAM vehicles are either in development or production. Most, if not all, have a goal of fully autonomous vehicle operations, but fully autonomous flying vehicles are not expected in the near future. Therefore, we are de-veloping concepts for UAM vehicles that will be easy to fly and/or manage by operators with minimal pilot training. In this paper we will discuss our human-automation teaming approach to develop an easy-to-operate VTOL aircraft, and some of the fly-by-wire technology needed to stabilize the vehicle so that a sim-ple ecological mental model of the flying task can be implemented. We will discuss the requirements for a stability augmentation system that must be developed to support our simple pilot input model, and also present design guidelines and requirements based on a pilot input and management model. Finally, our ap-proach to vehicle development will involve considerable operator testing and evaluation: improving pilot model, inceptors, displays and also work on a plan for how a UAM vehicle can be integrated with terminal area air traffic control airspace with minimal impact on controller workload.

UAM↗
NASA NTRS2014

Pilot Evaluation of a UAS Detect-and-Avoid System's Effectiveness in Remaining Well Clear

Unmanned aircraft will equip with a detect-and-avoid (DAA) system that enables them to comply with the requirement to "see and avoid" other aircraft, an important layer in the overall set of procedural, strategic and tactical separation methods designed to prevent mid-air collisions. Regulators will establish minimum operating standards for DAA effectiveness, but different combinations of algorithms, displays and procedures could be used to meet those standards. The research presented in this paper indicates the effectiveness of the combined pilot-DAA system as a function of the DAA design requirements and provides data that may be used to model the behavior of pilots when employing such systems. Two simulations involving 21 professional unmanned aircraft system (UAS) pilots evaluated eight different DAA system designs in order to assess their ability to maintain the "well clear" separation standard, i.e., the state of maintaining a safe distance from other aircraft that would not normally cause the initiation of a collision avoidance maneuver by either aircraft. When the traffic display was integrated with the primary mission map directly in front of the pilot, there were fewer losses of well clear. Greater warning time provided to the pilot was strongly correlated with success in remaining well clear. Pilots' ability to separate from aircraft with cooperative and non-cooperative surveillance systems was nearly the same after accounting for the amount of alert time provided in each encounter, although the limited surveillance volume for the airborne-equipped aircraft meant alerts tended to occur later and therefore were more difficult to resolve.

detect-and-avoid↗
NASA NTRS2015

Pilot Evaluation of a UAS Detect-and-Avoid System's Effectiveness in Remaining Well Clear

Unmanned aircraft will equip with a detect-and-avoid (DAA) system that allows them to comply with the requirement to see and avoid other aircraft, an important layer in the overall set of procedural, strategic and tactical separation methods designed to prevent mid-air collisions. Although the effectiveness of the DAA system will be set to a minimum threshold by regulators, different combinations of algorithms, displays and procedures could be used to meet that minimum. The research presented in this paper indicates the effectiveness of the combined pilot-DAA system as a function of the DAA design requirements and provides data that may be used to model the behavior of pilots when employing such systems. Over the course of two simulations 21 professional UAS pilots evaluated eight different DAA system designs and metrics were collected on their ability to maintain the well clear separation standard. The independent variables were the time horizon at which pilots were alerted to potential losses of well clear, the location of the traffic display, and the tools and informational elements available on the display to aid the pilot in detecting and resolving those potential losses. In the second experiment the UAS encountered two categories of aircraft: those equipped with simulated transponders that could be seen dozens of miles away and those without that were only detectable by a simulated radar within a range of six nautical miles. The data indicate that integrating the traffic display with the primary mission map directly in front of the pilot reduced the frequency of losses of well clear. Improved detection and resolution tools, including explicit maneuver guidance and a trial planning capability, had less of an effect in reducing the frequency of losses but significantly reduced the time in loss when they occurred. The amount of warning time provided to the pilot had a strong effect on their ability to remain well clear: when alerts were first presented with less than about 15 seconds to a predicted loss of well clear pilots were able to maneuver successfully in only 26 percent of encounters, whereas they were about 83 percent successful when they had more than 15 seconds. Pilots' ability to separate from the two categories of aircraft was nearly the same after accounting for the amount of alert time provided in each encounter, although the limited surveillance volume for the non-transponder equipped aircraft meant alerts tended to occur later and therefore were more difficult to resolve.

loss of well clear↗
NASA NTRS1978

Modeling the effects of high-G stress on pilots in a tracking task

Air-to-air tracking experiments were conducted at the Aerospace Medical Research Laboratories using both fixed and moving base dynamic environment simulators. The obtained data, which includes longitudinal error of a simulated air-to-air tracking task as well as other auxiliary variables, was analyzed using an ensemble averaging method. In conjunction with these experiments, the optimal control model is applied to model a human operator under high-G stress.

Korn, J.↗
NASA NTRS1980

A mathematical representation of an advanced helicopter for piloted simulator investigations of control system and display variations

A mathematical model of an advanced helicopter is described. The model is suitable for use in control/display research involving piloted simulation. The general design approach for the six degree of freedom equations of motion is to use the full set of nonlinear gravitational and inertial terms of the equations and to express the aerodynamic forces and moments as the reference values and first order terms of a Taylor series expansion about a reference trajectory defined as a function of longitudinal airspeed. Provisions for several different specific and generic flight control systems are included in the model. The logic required to drive various flight control and weapon delivery symbols on a pilot's electronic display is also provided. Finally, the model includes a simplified representation of low altitude wind and turbulence effects. This model was used in a piloted simulator investigation of the effects of control system and display variations for an attack helicopter mission.

Aiken, E. W.↗
DOE OSTI2026

Physics basis for the reference flat-top plasma scenario in the ST–E1 fusion power plant

As part of the U.S. Department of Energy’s Milestone-Based Fusion Energy Development Program, Tokamak Energy has completed the pre-concept design of the ST–E1 fusion power plant. ST–E1 is envisaged to operate in two phases: a pilot plant phase, targeting sustained net power production of 300 - 500 MWe for a duration >1 hr, followed by a commercial power plant phase targeting steady-state operations and a normalised overnight capital cost of ⩽12 000 $\$$/kWe. The design process adopted was highly iterative, integrating all major plant systems and progressing in a phased fidelity approach. At the pre-conceptual stage, the emphasis has been on exploring the design space, identifying the main system-level trade-offs, and making the key decisions that define the overall plant concept, rather than optimising a single operating point. This paper, part of a focused collection detailing the ST–E1 pre-concept design, addresses the development of a series of reference flat-top plasma operating points for the pilot plant phase. A modelling workflow was established to develop and assess candidate plasma design points and explore key dependencies. The workflow includes integrated core plasma modelling, magnetohydrodynamic (MHD) stability assessment, equilibrium generation, scrape-off-layer and exhaust modelling, heating & current drive design and optimisation, and turbulent transport modelling. Using this framework, the impact of several key parameters on the flat-top operating space was investigated, including the density limit, core radiation fraction and divertor power loading, level of external heating and curent drive power and assumed pedestal characteristics. The MHD stability, controllability and micro-stability characteristics of these plasmas were also analysed. These investigations informed the definition of a set of fully non-inductive, flat-top reference operating points that satisfy the high-level ST–E1 mission, including a low and high density case, a case that is stable to resistive wall modes and a case with reduced divertor power loading.

ST–E1↗