Search NASA⌕ Search

SEARCH · Search NASA

Results for “Damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Effects of Displacement Damage on the Time-Resolved Gain and Bandwidth of a Low Breakdown Voltage Si Avalanche Photodiode

Effects of displacement damage and ionization damage induced by gamma irradiation on the dark current and impulse response of a high-bandwidth low breakdown voltage Si Avalanche Photodiode has been investigated using picosecond laser microscopy. At doses as high as 10Mrad (Si) minimal alteration in the impulse response and bandwidth were observed. However, dark current measurements also performed with and without biased irradiation exhibit anomalously large damage factors for applied biases close to breakdown. The absence of any degradation in the impulse response is discussed as are possible mechanisms for higher dark current damage factors observed for biased irradiation.

bandwidth↗
NASA NTRS2016

Using Satellite Remote Sensing to Assist the National Weather Service (NWS) in Storm Damage Surveys

In the United States, the National Oceanic and Atmospheric Administration (NOAA) National Weather Service (NWS) is charged with performing damage assessments when storm or tornado damage is suspected after a severe weather event. This has led to the development of the Damage Assessment Toolkit (DAT), an application for smartphones, tablets and web browsers that allows for the collection, geolocation, and aggregation of various damage indicators collected during storm surveys.

Damage surveys↗
NASA NTRS2017

Simulation-Based Height of Burst Map for Asteroid Airburst Damage Prediction

Entry and breakup models predict that airburst in the Earth's atmosphere is likely for asteroids up to approximately 200 meters in diameter. Objects of this size can deposit over 250 megatons of energy into the atmosphere. Fast-running ground damage prediction codes for such events rely heavily upon methods developed from nuclear weapons research to estimate the damage potential for an airburst at altitude. (Collins, 2005; Mathias, 2017; Hills and Goda, 1993). In particular, these tools rely upon the powerful yield scaling laws developed for point-source blasts that are used in conjunction with a Height of Burst (HOB) map to predict ground damage for an airburst of a specific energy at a given altitude. While this approach works extremely well for yields as large as tens of megatons, it becomes less accurate as yields increase to the hundreds of megatons potentially released by larger airburst events. This study revisits the assumptions underlying this approach and shows how atmospheric buoyancy becomes important as yield increases beyond a few megatons. We then use large-scale three-dimensional simulations to construct numerically generated height of burst maps that are appropriate at the higher energy levels associated with the entry of asteroids with diameters of hundreds of meters. These numerically generated HOB maps can then be incorporated into engineering methods for damage prediction, significantly improving their accuracy for asteroids with diameters greater than 80-100 m.

Burst Map↗
NASA NTRS2018

Simulation of Stochastic Mud-Crack Damage Formation in an Environmental Barrier Coating

The integrated Finite Element Analysis–Micromechanics Analysis Code/Ceramics Analysis and Reliability Evaluation of Structures (FEAMAC/CARES) program was used to simulate the formation of mudflat-cracks from thermomechanical loading on a multi-layered Environmental Barrier Coating (EBC) system deposited on a ceramic substrate. FEAMAC/CARES combines MAC/GMC multiscale composite micromechanics code with CARES/Life probabilistic multiaxial failure criteria code and Abaqusfinite element analysis. In this work, step function elastic modulus reduction of randomly damaged finite elements was used to represent discrete cracking events. The use of many small-sized low-aspect-ratio finite elements enabled the depiction of crack boundaries and formation of mudflat patterned damage. Demonstrated examples include finite element models of button–sized disk–shaped 3-D specimen, and a 2-D model of through-the-thickness cross-section. All models were subjected to a progressive cool down from 1300oC to room temperature. Mudflat crack damage in the coating system resulted from the buildup of residual tensile stresses between the individual material constituents from thermal expansion mismatch. A 2-parameter Weibull distribution characterized the coating layer stochastic strength response and the effect of the Weibull modulus on the formation of damage was studied here.

residual tensile stress↗
NASA NTRS2018

Weibull-Based Stochastic Simulation of Mud-Crack Damage Formation in an Environmental Barrier Coating

The integrated Finite Element Analysis Micromechanics Analysis Code/Ceramics Analysis and Reliability Evaluation of Structures (FEAMAC/CARES) program was used to simulate the formation of mudflat-cracks from thermomechanical loading on a multi-layered Environmental Barrier Coating (EBC) system deposited on a ceramic substrate. FEAMAC/CARES combines MAC/GMC (Micromechanics Analysis Code/Generalized Method of Cells) multiscale composite micromechanics code with CARES/Life probabilistic multiaxial failure criteria code and Abaqusfinite element analysis. In this work, step function elastic modulus reduction of randomly damaged finite elements was used to represent discrete cracking events. The use of many small-sized low-aspect-ratio finite elements enabled the depiction of crack boundaries and formation of mudflat patterned damage. Demonstrated examples include finite element models of button-sized disk-shaped 3-D specimen, and a 2-D model of through-the-thickness cross-section. All models were subjected to a progressive cool down from 1300 degrees Centigrade to room temperature. Mudflat crack damage in the coating system resulted from the buildup of residual tensile stresses between the individual material constituents from thermal expansion mismatch. A 2-parameter Weibull distribution characterized the coating layer stochastic strength response and the effect of the Weibull modulus on the formation of damage was studied here.

Residual Tensile Stress↗
NASA NTRSDate not supplied

Progressive Damage Mechanisms in Thick 3D Composite Structures under Static and Fatigue Loading

The objective of this work is to demonstrate validation of predictive capabilities capturing both damage initiation and growth under static and fatigue loading in geometrically complex three-dimensional (3D) composite structures. The composite structure of interest in the present study resembles a 3D blade spar used in rotorcraft applications. Under both static and fatigue testing, it was shown that damage initiated at the same ply-drop location(s) and grew in the axial as well as hoop directions. CompDam – a state-of-the-art Progressive Damage Analysis (PDA) tool was used to achieve successful correlations of metrics including load-displacement responses and damage modes.

progressive damage analysis↗
NASA NTRS2021

Flood Monitoring and Crop Damage Assessment

In recent years, the occurrence and impact of inland and coastal flood events have become more frequent and damaging, especially within agricultural fields, due to the global climate change and consistent sea level rise. Monitoring and measuring the magnitude of flood events in a timely manner and assessing the subsequent crop damages accurately are precursors in minimizing detrimental consequences that could potentially lead to a global food security crisis. Traditional gauge-based measurements with sophisticated hydrological models are capable of monitoring flood events precisely but limited within the smaller spatial extent, time-consuming, and costly. In recent decades, advancement in airborne- and satellite-based remote sensing technologies offering products at a daily global spatial extent with various spectral resolution helps address the shortcomings of the traditional in situ approaches in flood monitoring. Furthermore, the methods such as classification and band ratioing using remote sensing products are simple and effective in assessing flood-induced agricultural damages. The combination of remote sensing products and geographic information systems along with the current development in web mapping, users now can get near real-time flood monitoring and crop damage assessments, albeit dependent upon the quality of available data. A case study to quantify the impact of the 2011 Missouri Mississippi River flooding on the surrounding cornfield was performed through a regression model. The model was trained using historical daily NDVI and corn yield across Nebraska and Missouri, and the overall accuracy in estimating corn yield was about 90%. The method implemented in this localized case study could be extended at a larger geographical scale.

Flood monitoring↗
NASA NTRS1971

Damage and recovery characteristics of lithium-containing solar cells.

Damage and recovery characteristics were measured on lithium-containing solar cells irradiated by 1-MeV electrons. Empirical expressions for cell recovery time, diffusion-length damage coefficient immediately after irradiation, and diffusion-length damage coefficient after recovery were derived using results of short-circuit current, diffusion-length, and reverse-bias capacitance measurements. The damage coefficients were expressed in terms of a single lithium density parameter, the lithium gradient. A fluence dependence was also established, this dependence being the same for both the immediate-post-irradiation and post-recovery cases. Cell recovery rates were found to increase linearly with lithium gradient.

Faith, T. J.↗
NASA NTRS1972

The octahedral shear strain theory and its relation to biaxial cumulative fatigue damage.

The octahedral shear strain range concept is used in analyzing multiaxial fatigue damage. Limited test data from a two-step loading sequence show that the loading effect is still pronounced in the multiaxial case and that the relation between damage and cycle ratio is nonlinear. Among uniaxial cumulative damage concepts, the modified multiaxial double linear damage rule seems to show the most favorable experimental results.

Zamrik, S. Y.↗
NASA NTRS1972

Contamination damage avoidance concepts for propulsion feed system components.

The potential gain in the reliability of reusable long-term mission vehicles through the minimization of component damage due to the ingestion of particulate contamination by feed system components has been recognized by the NASA-LeRC and MDAC, and a program to investigate these problems has been completed. This investigation covered the determination of the cycle life of a typical 2-in. poppet type of shutoff valve in an uncontaminated GH2 environment and then compared this component performance with simulated operation with GN2 and LN2 containing controlled amounts of AL2O2 contaminant particles. The original valve design was tested for contamination damage tolerance characteristics under full flow and cyclic operating conditions, redesigned to improve the damage tolerance to contaminants and then retested. A second method of approach to damage tolerance control was investigated through the evaluation of various types of particulate separation devices. The study included various types of dynamic separators but did not cover conventional filter assemblies.

Endicott, D. L.↗
NASA NTRS1974

Some effects of applied stress on early stages of cavitation damage

The phenomenon of cavitation flow damage is discussed. The initial phases of damage and the effect of external stresses on the extent to which damage is incurred are analyzed. Three experimental facilities were used to procure the data required: (1) a water loop with venturi, (2) a mercury loop with venturi, and (3) a vibratory facility (stationary specimen, nonflow system). A description of each system is provided for the clarification of test conditions. Photographs of typical cavitation damage instances are included.

Kemppainen, D. J.↗
NASA NTRS1974

Satellite detection of vegetative damage and alteration caused by pollutants emitted by a zinc smelter

The author has identified the following significant results. Field observations and data collected by low flying aircraft were used to verify the accuracy of maps produced from the satellite data. Although areas of vegetation as small as six acres can accurately be detected, a white pine stand that was severely damaged by sulfur dioxide could not be differentiated from a healthy white pine stand because spectral differences were not large enough. When winter data were used to eliminate interference from herbaceous and deciduous vegetation, the damage was still undetectable. The analysis was able to produce a character map that accurately delineated areas of vegetative alteration due to high zinc levels accumulating in the soil. The map depicted a distinct gradient of less damage and alteration as the distance from the smelter increased. Although the satellite data will probably not be useful for detecting small acreages of damaged vegetation, it is concluded that the data may be very useful as an inventory tool to detect and delineate large vegetative areas possessing differing spectral signatures.

Mcmurtry, G. J.↗
NASA NTRS1975

Modeling damaged wings: Element selection and constraint specification

The NASTRAN analytical program was used for structural design, and no problems were anticipated in applying this program to a damaged structure as long as the deformations were small and the strains remained within the elastic range. In this context, NASTRAN was used to test three-dimensional analytical models of a damaged aircraft wing under static loads. A comparison was made of calculated and experimentally measured strains on primary structural components of an RF-84F wing. This comparison brought out two sensitive areas in modeling semimonocoque structures. The calculated strains were strongly affected by the type of elements used adjacent to the damaged region and by the choice of multipoint constraints sets on the damaged boundary.

Stronge, W. J.↗
NASA NTRS1975

Electron and proton damage coefficients in low-resistivity silicon

The electron and proton damage coefficients for low resistivity p-type boron-doped silicon were determined from minority-carrier lifetime measurements on bulk material and diffusion length measurements on solar cells. The bulk samples were irradiated with electrons at three energy levels (0.5, 1.5, and 2.5 MeV) using a Dynamitron. Lifetime measurements were made with a steady-state photoconductivity apparatus, and comparison measurements of diffusion length were obtained using the steady-state surface photovoltage method (Goodman, 1961). The diffusion-length damage coefficients increased with decreasing resistivity for boron-doped silicon; this dependence can be qualitatively accounted for using a two-level Hall-Shockley-Read model. The damage coefficients for solar cells were larger than for their bulk-material counterparts. The damage coefficient was apparently independent of the dislocation density in the 0.1 ohm-cm bulk samples and solar cells investigated.

Srour, J. R.↗
NASA NTRS1977

Image dissector photocathode solar damage test program

Image dissector sensors of the same type which will be used in the NASA shuttle star tracker were used in a series of tests directed towards obtaining solar radiation/time damage criteria. Data were evaluated to determine the predicted level of operability of the star tracker if tube damage became a reality. During the test series a technique for reducing the solar damage effect was conceived and verified. The damage concepts are outlined and the test methods and data obtained which were used for verification of the technique's feasibility are presented. The ability to operate an image dissector sensor with the solar image focussed on the photocathode by a fast optical lens under certain conditions is feasible and the elimination of a mechanical protection device is possible.

Smith, R. A.↗
NASA NTRS1977

Fatigue damage of notched boron/epoxy laminates under constant-amplitude loading

Fatigue damage in (0, plus or minus 45) and (0, plus or minus 45, 90) boron/epoxy laminates was studied with X-ray radiography and scanning electron microscopy. In addition, limited tests for residual strength and stiffness were performed. Initially, fatigue damage in both (0, plus or minus 45) and (0, plus or minus 45, 90) laminates occurred as intralaminar cracks around the edge of the hole. Then, whenever further damage developed, intralaminar cracks in the plus or minus 45-deg plies began to propagate from the edge of the hole. Finally, in both types of laminates, primarily plus or minus 45-deg fibers broke (prior to two-piece failure) where intralaminar cracks in the plus or minus 45-deg plies had occurred. In the (0, plus or minus 45) laminates, the 45-deg plies developed intralaminar and transthickness cracks along lines parallel to the loading axis and tangent to the hole in the test specimen. This damage, which was most pronounced under compressive loads, had little effect on either strength or stiffness. In contrast, in the (0, plus or minus 45, 90) laminates, the plus or minus 45-deg plies developed intralaminar cracks transverse to the loading axis.

Roderick, G. L.↗
NASA NTRS1978

Using reflectance and photography to detect ozone damage to cantaloupe plants

Laboratory and field reflectance measurements showed that ozone-damaged cantaloupe (Cucumis melo L.) leaves had lower water contents and higher reflectance than nondamaged leaves. Cantaloupe plants with lightly, severely, and very severely ozone-damaged leaves were distinguishable from nondamaged plants by reflectance measurements in the 1.35-2.5-micron near-IR water absorption band. Ozone-damaged leaf areas were detected photographically 16 hours before the damage was visible.

Gausman, H. W.↗
NASA NTRS1979

Dynamic response of damaged angleplied fiber composites

The effects of low level damage induced by monotonic load, cyclic load and/or residual stresses on the vibration frequencies and damping factors of fiber composite angleplied laminates were investigated. Two different composite systems were studied - low modulus fiber and ultra high modulus fiber composites. The results obtained show that the frequencies and damping factors of angleplied laminates made from low modulus fiber composites are sensitive to low level damage while those made from ultra high modulus composites are not. Vibration tests may not be sufficiently sensitive to assess concentrated local damage in angleplied laminates. Dynamic response determined from low-velocity impact coupled with the Fast Fourier Transform and packaged in a minicomputer can be a convenient procedure for assessing low-level damage.

Chamis, C. C.↗