Search NASA⌕ Search

SEARCH · Search NASA

Results for “effective diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Thermal diffusivity of diamond films using a laser pulse technique

Polycrystalline diamond films were deposited using a microwave plasma-enhanced chemical vapor deposition process. A laser pulse technique was developed to measure the thermal diffusivity of diamond films deposited on a silicon substrate. The effective thermal diffusivity of a diamond film on silicon was measured by observing the phase and amplitude of the cyclic thermal waves generated by laser pulses. An analytical model is presented to calculate the effective in-plane (face-parallel) diffusivity of a two-layer system. The model is used to reduce the effective thermal diffusivity of the diamonds/silicon sample to a value for the thermal diffusivity and conductivity of the diamond film. The average effective diffusivity values are 1.47 + or - 0.03 and 1.83 + or - 0.10 yielding thermal diffusivity values of 7.46 + or - 0.90 and 7.33 + or - 0.70 sq cm/s respectively, for the two samples; the calculated thermal con ductivity values are 13.50 and 13.28 W/cmK, which are better than that of type 1a natural diamond. The phase and amplitude measurements give similar results.

Albin, Sacharia↗
NASA NTRS1956

An analog study of a shock-position diffuser control on a supersonic turbojet engine

Shock position was assumed to be controlled by air bleed through a diffuser-exit bypass door operated by a second-order servomotor. Pressure disturbance resulting from changes in bypass-door position had whereas a disturbance in engine speed had a large effect on diffuser pressure and could impose severe requirements on diffuser control response. The controlled diffuser response improved with faster servomotor response and smaller diffuser dead time and lag. The effect of diffuser dead time on diffuser response was greater than the effect of diffuser lag.

Novik, David↗
NASA NTRS1973

The application of far IR lasers to the investigation of the optical properties of materials

The effect of diffusion on the saturation and absorption properties of molecular gases is considered. The analysis starts with a simple derivation of the multi-level rate equations. Incorporating the diffusion term, calculations are carried out both for the homogeneous and inhomogeneous broadening cases. Both graphical and analytical solutions are obtained for the absorption coefficient and the saturation intensity. It is shown that the effect of diffusion is characterized by a diffusion function, which varies inversely with the radius of the beam at low pressures and small beam sizes. The analysis is done in terms of two parameters k1a and k2a, which are simple functions of the intensity of the beam I, the effective relaxation rate w, and the effective diffusion constant D the a is designated as the radius of the beam.

Stafsudd, O. M.↗
NASA NTRS2001

Nonlinearity Effects of Lateral Density Diffusion Coefficient on Gain-Guided VCSEL Performance

Electron and hole diffusions in the plane of semiconductor quantum wells play an important part in the static and dynamic operations of semiconductor lasers. In this paper, we apply a hydrodynamic model developed from the semiconductor Bloch equations to numerically study the effects of nonlinearity in the diffusion coefficient on single mode operation and direct modulation of a gain-guided InGaAs/GaAs multiple quantum well laser, operating not too far from threshold. We found that a small diffusion coefficient is advantageous for lowering the threshold current and increasing the modulation bandwidth. Most importantly, the effects of nonlinearity in the coefficient can be approximately reproduced by replacing the coefficient with an effective constant diffusion coefficient, which corresponds roughly to the half height density of the density distribution.

Li, Jian-Zhong↗
DOE OSTI2022

Passive and active peer effects in the spatial diffusion of residential solar panels: A case study of the Las Vegas Valley

This research analyzes the role of peer influences on the adoption of residential rooftop solar photovoltaic panels (PV) within the context of the Diffusion of Innovation Theory. PV literature indicates that adopters are influenced by word of mouth (WOM) information exchange with peers, i.e., active peer effects, while other studies suggest that living near households with visible rooftop PV installations influences adoption, i.e., passive peer effects. We bridge the gap in this literature by conducting a mixed methods analysis. We develop and administer a survey to Las Vegas Valley (LVV) residents to identify current and potential PV adopters' perceptions of peer-effects and consumer intention variables. We conduct a spatial analysis of Google's Project Sunroof data to identify LVV neighborhoods in the later stages of the PV diffusion process, i.e., those with the highest PV adoption rates. Key results show that current PV adopters living in early diffusion areas report significantly higher active and passive peer effects compared to adopters in later diffusion areas. Potential adopters in later diffusion areas report higher passive peer effects than those in early diffusion areas. Overall, because LVV has a low PV adoption rate (<3%), short term strategies aimed at increasing PV adoption should emphasize WOM active peer effects. Here, we caution against long-term green marketing strategies focusing solely on peer-effects as the PV market matures.

14 SOLAR ENERGY↗
DOE OSTI2022

Assessment and Improvement of Fission Product Transport Predictions of Particle Fuel in BISON

The U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. This study was motivated by the need to incorporate more physics-based models in BISON in order to foster tri-structural isotropic (TRISO) applications. This document details the integration of new modeling capabilities in BISON, including (1) development of pyrolytic carbon (PyC) and silicon carbide (SiC) layer anisotropic thermal and mass transport capabilities, (2) verification of the mass diffusion solution in TRISO modeling, (3) calibration of fission product diffusivity using Advanced Gas Reactor (AGR) experiments, (4) improved fission product release modeling by developing compact diffusion modeling capabilities, and (5) documentation of accelerated failure analysis on the BISON website. Improvements made to the diffusion models and parameters were documented and validated against AGR-1 and -2 experiment data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1992

The effect of tensile stress on hydrogen diffusion in metal alloys

The effect of tensile stress on hydrogen diffusion has been determined for Type 303 stainless steel, A286 CRES, and Waspaloy and IN100 nickel-base alloys. It was found that hydrogen diffusion coefficients are not significantly affected by stress, while the hydrogen permeabilities are greatly affected in Type 303 stainless steel and A286 CRES (iron-based alloys), but are affected little in Waspaloy (nickel-base) and not affected in all in IN100 (nickel base). These observations might be taken as an indication that hydrogen permeabilities are affected by stress in iron-based alloys, but only slightly affected in nickel-based alloys. However, it is too early to make such a generalization based on the study of only these four alloys.

Danford, M. D.↗
NASA NTRS1996

The Effects of Flame Structure on Extinction of CH4-O2-N2 Diffusion Flames

The effects of flame structure on the extinction limits of CH4-O2-N2 counterflow diffusion flames were investigated experimentally and numerically by varying the stoichiometric mixture fraction Z(sub st), Z(sub st) was varied by varying free-stream concentrations, while the adiabatic flame temperature T(sub ad) was held fixed by maintaining a fixed amount of nitrogen at the flame. Z(sub st) was varied between 0.055 (methane-air flame) and 0.78 (diluted- methane-oxygen flame). The experimental results yielded an extinction strain rate K(sub ext) of 375/s for the methane-air flame, increasing monotonically to 1042/s for the diluted-methane-oxygen flame. Numerical results with a 58-step Cl mechanism yielded 494/s and 1488/s, respectively. The increase in K(sub ext) with Z(sub st) for a fixed T(sub ad) is explained by the shift in the O2 profile toward the region of maximum temperature and the subsequent increase in rates for chain-branching reactions. The flame temperature at extinction reached a minimum at Z(sub st) = 0.65, where it was 200 C lower than that of the methane-air flame. This significant increase in resistance to extinction is seen to correspond to the condition in which the OH and O production zones are centered on the location of maximum temperature.

Du, J.↗
NASA NTRS1990

Double-diffusive convection and its effect under reduced gravity

This paper reviews recent results on three aspects of double-diffusive convection under reduced gravity: diffusive instability caused by sideways heating, diffusive instability caused by bottom heating, and the salt-finger convection case. Some of the processes that are likely to occur during solidification are highlighted. Using property values of lead-tin alloy, it is concluded that diffusive instabilities are unlikely to occur at steady reduced gravity levels of 0.01 and 0.0001 g(0). Salt finger convection is likely to be generated, however.

Chen, C. F.↗
DOE OSTI2021

Magnetic-field generation and its effect on ablative Rayleigh–Taylor instability in diffusive ablation fronts

The effects of self-generated magnetic fields on the ablative Rayleigh–Taylor (RT) instability are investigated in the linear regime. The main governing parameters are the Froude number (Fr), which stands for the ratio between ablative convection and acceleration of the target, and the Mach number at the ablation front (Ma), assumed to be small (isobaricity). During the development of the RT instability, magnetic fields are generated due to misalignment between pressure and density gradients (Biermann-battery effect). They accumulate at the section of the ablation front where the Nernst and the plasma velocities cancel each other. The magnetic field modifies the dynamics of the instability through the Righi–Leduc term, which acts as a heat source in the energy equation. It is found that the B fields affect perturbations with short wavelengths up to the most unstable wave in the spectrum. Here, the B field plays a destabilizing role for moderate Froude numbers and becomes stabilizing for large Froude numbers. For plastic ablators, the Fr threshold is found to be Fr = 5.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Effect of Carbon on Void Nucleation in Iron

The study reports the significance of carbon presence in affecting void nucleation in Fe. Without carbon, void nucleation rates decrease gradually at high temperatures but remain significantly high and almost saturated at low temperatures. With carbon present, even at 1 atomic parts per million, void nucleation rates show a low-temperature cutoff. With higher carbon levels, the nucleation temperature window becomes narrower, the maximum nucleation rate becomes lower, and the temperature of maximum void nucleation shifts to a higher temperature. Fundamentally, this is caused by the change in effective vacancy diffusivity due to the formation of carbon-vacancy complexes. The high sensitivity of void nucleation to carbon comes from the high sensitivity of void nucleation to the vacancy arrival rate in a void. The void nucleation is calculated by first obtaining the effective vacancy diffusivity considering the carbon effect, then calculating the defect concentration and defect flux change considering both carbon effects and pre-existing dislocations, and finally calculating the void nucleation rate based on the recently corrected homogeneous void nucleation theory. The study is important not only in the fundamental understanding of impurity effects in ion/neutron irradiation but also in alloy engineering for judiciously introducing impurities to increase swelling resistance, as well as in the development of simulation and modeling methodologies applicable to other metals.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effective kinetics driven by dynamic concentration gradients under coupled transport and reaction

Biogeochemical reaction kinetics are generally established from batch reactors where concentrations are uniform. In natural systems, many biogeochemical processes are characterized by spatially and temporally variable concentration gradients that often occur at scales which are not resolved by field measurements or biogeochemical and reactive transport models. Yet, it is not clear how these sub-scale chemical gradients affect reaction kinetics compared to batch kinetics. Here we investigate this question by studying the paradigmatic case of localized pulses of solute reacting with a solid or a dissolved species in excess. Additionally, we consider non-linear biogeochemical reactions, representative of mineral dissolution, adsorption and redox reactions, which we quantify using simplified power-law kinetics. The combined effect of diffusion and reaction leads to effective kinetics that differ quantitatively and qualitatively from the batch kinetics. Depending on the nonlinearity (reaction order) of the local kinetics, these effects lead to either enhancement or decrease of the overall reaction rate, and result in a rich variety of reaction dynamics. We derive analytical results for the effective kinetics, which are validated by comparison to direct numerical simulations for a broad range of Damköhler numbers and reaction order. Our findings provide new insights into the interpretation of imperfectly mixed lab experiments, the effective kinetics of field systems characterized by intermittent reactant release and the integration of sub-scale concentration gradients in reactive transport models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1972

Development and pilot line production of lithium doped silicon solar cells

The work performed over the period of September 1971 to August 1972 to develop production processes for fabrication of lithium doped P/N cells is described. The BCl3 diffusion without 02 was selected as the optimum diffusion process for fabrication of lithium doped cells. An 8-2-7 (warm up - deposition - drive-in time in minutes) diffusion schedule at 1055 C was used for the first two lots (300 cells each) delivered to JPL. Cell efficiencies ranged from 11.0 to 13.7% based on an AMO of 135.3 mW/sq cm. These high efficiencies were obtained using from 10 to 40 cells per boron diffusion; increasing the quantity beyond 40 resulted in lower outputs. At this point, the emphasis was placed on investigation of a BCl3 with 02 diffusion. Through evaluation of the effects of diffusion time and temperature, gas flow rates, and desposition plus drive-in vs. continuous deposition and no drive-in cycles, diffusion parameters were determined which produced short circuit currents of 136 + or - 4 mA for ten cells spaced along 12 in. of the diffusion boat. The quantity was increased to 60, 100, and 150 cell diffusions with no more variation in cell short circuit current than observed with 10 cells.

Payne, P. A.↗
NASA NTRS1992

Effect of surface tension on the onset of convection in a double-diffusive layer

The effect of surface tension on the stability of a double-diffusive layer is considered using linear stability analysis. The surface tension is assumed to vary linearly with temperature and solute concentration. The eigenvalue problem is solved by the Galerkin method. Results show that the predicted stability boundary based on Marangoni effects alone is completely altered in the presence of buoyancy effects induced by low gravity levels (about 10 exp -5 g). At reduced gravity levels, salt-finger instability may onset in the overstable mode due to the stabilizing effect of surface tension. Fluid properties in terms of the Prandtl and the Lewis numbers have a profound effect on the stability conditions; opposite stability characteristics are found in salt solutions and in molten metals.

Chen, C. F.↗