SEARCH · Search NASA

Results for “parametric”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Results of a parametric aeroelastic stability analysis of a generic X-wing aircraft

This paper discusses the trend in longitudinal dynamic aeroelastic stability of a generic X-Wing aircraft model with design parameter variations. X-Wing rotor blade sweep angle, ratio of blade mass to total vehicle mass, blade structural stiffness cross-coupling and vehicle center-of-gravity location were parameters considered. The typical instability encountered is body-freedom flutter involving a low frequency interaction of the first elastic mode and the aircraft short period mode. Parametric cases with the lowest static margin consistently demonstrated the highest flutter dynamic pressures. As mass ratio was increased, the flutter boundary decreased. The decrease was emphasized as center-of-gravity location was moved forward. As sweep angle varied, it was observed that the resulting increase in forward-swept blade bending amplitude relative to aft blade bending amplitude in the first elastic mode had a stabilizing effect on the flutter boundary. Finally, small amounts of stiffness cross-coupling in the aft blades increased flutter dynamic pressure.

Woods, Jessica A.↗

NASA NTRS1988

Parametric analysis of synthetic aperture radar data for the study of forest stand characteristics

A parametric analysis of a Gulf Coast forest stand was performed using multipolarization, multipath airborne SAR data, and forest plot properties. Allometric equations were used to compute the biomass and basal area for the test plots. A multiple regression analysis with stepwise selection of independent variables was performed. It is found that forest stand characteristics such as biomass, basal area, and average tree height are correlated with SAR data.

Wu, Shih-Tseng↗

NASA NTRS1989

Time evolution from linear to nonlinear stages in magnetohydrodynamic parametric instabilities

The nonlinear evolution of the magnetohydrodynamic (MHD) parametric instability of wave fluctuations propagating along an unperturbed magnetic field is investigated. Both a magnetohydrodynamic perturbation-theoretical approach and a nonlinear MHD simulation are used. It is shown that high harmonic waves are rapidly excited by wave-wave coupling, and that the wave spectrum evolves from a state containing a small number of degrees of freedom in k space to one which contains a large number of degrees of freedom. It is found that the spectral evolution prior to nonlinear saturation is well described by the prturbation theory. During this stage, the ratio of the growth rate of the nth harmonic wave to the linear growth rate of the fundamental wave is n. The nonlinear saturation stage is characterized by a frequency shift of the fundamental wave that destroys the wave-wave resonance condition which, in turn, causes the wave amplitude to cease its growth.

Hoshino, M.↗

NASA NTRS1989

A parametric study of space radiation exposures to critical body organs for low earth orbit missions

It is shown that it is possible to calculate the extent of the exposure to space radiation of a specific body organ. Using a computerized anatomical man model and models of radiation environments and spacecraft shielding, a parametric study was carried out for several Space-Shuttle scenarios. The dose equivalent data for several blood-forming organ locations are presented (for a solar-minimum epoch) as a function of altitude and the shielding material, and the results are compared with the NASA crew exposure limits for these body organs.

Atwell, W.↗

NASA NTRS1989

Parametric amplification in AgGaSe2

AgGaSe2 has been grown, annealed, and characterized for the mid-IR. Characterization includes measurement of the average power-limiting factors including absorption and the variation of the refractive indices with temperature. Using specially annealed crystals 20 mm long and a Ho:YAG pump, parametric amplification at 3.39 microns has achieved a gain of 2.9 with a peak power input of only 8 MW/sq cm.

Barnes, Norman P.↗

NASA NTRS1990

A numerical parametric study of a scramjet inlet in a Mach 6 arc heated test facility

A numerical study of the NASA Langley Arc Heated Scramjet Test Facility (AHSTF) is reported. The facility test flow through the Mach 6 quasi-two-dimensional nozzle was computed, and the flow through the Langley parametric inlet was calculated using different regions of the computed facility nozzle exit flow as inflow, exploring in more detail the effect of boundary layer ingestion on inlet performance. The potential advantage of using a quasi-two-dimensional nozzle in the Langley AHSTF versus the square cross-sectioned nozzle currently used for Scramujet engine tests is explored in terms of resulting inlet performance.

Sekar, B.↗

NASA NTRS1990

Coherence properties of a doubly resonant monolithic optical parametric oscillator

A doubly resonant optical parametric oscillator (DRO) pumped with the second harmonic of a narrow-linewidth Nd:YAG laser is described. The linewidth of the DRO signal was less than 13 kHz, the DRO was shown to generate a phase-locked subharmonic of the pump at degeneracy, and the signal and the idler were shown to be mutually coherent with the pump and to be phase-anticorrelated with each other away from degeneracy. The signal-idler heterodyne linewidth was 500 Hz, and pump phase modulation was shown to transfer to the DRO phase at degeneracy.

Nabors, C. D.↗

NASA NTRS1990

Parametric study of an ODW scramaccelerator for hypersonic test facilities

A parametric study has been conducted for an oblique detonation-wave (ODW) 'scramaccelerator' suitable for projectile aerothermodynamics studies in real gas hypersonic test facilities. The results of the present analytical design evaluation indicate that an ODW scramaccelerator using conventional gaseous propellants can accelerate projectiles of 0.1 to 1000 kg masses to speeds in the 6-10 km/sec range. Potential applications for such an accelerator encompass a hypersonic ballistic test range, kinetic energy weapon accelerators, mass drivers to LEO, projectile terminal ballistics testing, projectile/target interaction studies, inertial welders, and shock compactors.

Humphrey, Joseph W.↗

NASA NTRS1989

Numerical simulation of flow through the Langley parametric scramjet engine

The numerical simulation of a three-dimensional turbulent, reacting flow through the entire Langley parametric scramjet engine has been obtained using a piecewise elliptic approach. The last section in the combustor has been analyzed using a parabolized Navier-Stokes code. The facility nozzle flow was analyzed as a first step. The outflow conditions from the nozzle were chosen as the inflow conditions of the scramjet inlet. The nozzle and the inlet simulation were accomplished by solving the three-dimensional Navier-Stokes equations with a perfect gas assumption. The inlet solution downstream of the scramjet throat was used to provide inflow conditions for the combustor region. The first two regions of the combustor were analyzed using the MacCormack's explicit scheme. However, the source terms in the species equations were solved implicitly. The finite rate chemistry was modeled using the two-step reaction model of Rogers and Chinitz. A complete reaction model was used in the PNS code to solve the last combustor region. The numerical solutions provide an insight of the flow details in a complete hydrogen-fueled scramjet engine module.

Srinivasan, Shivakumar↗

NASA NTRS1990

Variational formulation of high-performance finite elements - Parametrized variational principles

High-performance (HP) elements are simple finite elements constructed to deliver engineering accuracy with coarse arbitrary grids. This paper is part of a series on the variational basis of HP elements, with emphasis on those constructed with the free formulation (FF) and assumed natural strain (ANS) methods. The present paper studies parametrized variational principles that provide a foundation for the FF and ANS methods, as well as for a combustion of both methods.

Felippa, C. A.↗

NASA NTRS1991

Experimental parametric study of jet vortex generators for flow separation control

A parametric wind-tunnel study was performed with jet vortex generators to determine their effectiveness in controlling flow separation associated with low-speed turbulence flow over a two-dimensional rearward-facing ramp. Results indicate that flow-separation control can be accomplished, with the level of control achieved being a function of jet speed, jet orientation (with respect to the free-stream direction), and orifice pattern (double row of jets vs. single row). Compared to slot blowing, jet vortex generators can provide an equivalent level of flow control over a larger spanwise region (for constant jet flow area and speed). Dye flow visualization tests in a water tunnel indicated that the most effective jet vortex generator configurations produced streamwise co-rotating vortices.

Selby, Gregory↗

NASA NTRS1991

A parametric experimental investigation of a scramjet nozzle at Mach 6 with Freon and argon or air used for exhaust simulation

A parametric experimental investigation of a scramjet nozzle was conducted with a gas mixture used to simulate the scramjet engine exhaust flow at a free-stream Reynolds number of approximately 6.5 x 10(exp 6) per foot. External nozzle surface angles of 16, 20, and 24 deg were tested with a fixed-length ramp and for cowl internal surface angles of 6 and 12 deg. Pressure data on the external nozzle surface were obtained for mixtures of Freon and argon gases with a ratio of specific heats of about 1.23, which matches that of a scramjet exhaust. Forces and moments were determined by integration of the pressure data. Two nozzle configurations were also tested with air used to simulate the exhaust flow. On the external nozzle surface, lift and thrust forces for air exhaust simulation were approximately half of those for Freon-argon exhaust simulation and the pitching moment was approximately a third. These differences were primarily due to the difference in the ratios of specific heats between the two exhaust simulation gases. A 20 deg external surface angle produced the greatest thrust for a 6 deg cowl internal surface angle. A flow fence significantly increased lift and thrust forces over those for the nozzle without a flow fence.

Cubbage, James M.↗

NASA NTRS1991

Parametric trade studies on a Shuttle 2 launch system architecture

A series of trade studies are presented on a complementary architecture of launch vehicles as a part of a study often referred to as Shuttle-2. The results of the trade studies performed on the vehicles of a reference Shuttle-2 mixed fleet architecture have provided an increased understanding of the relative importance of each of the major vehicle parameters. As a result of trades on the reference booster-orbiter configuration with a methane booster, the study showed that 60 percent of the total liftoff thrust should be on the booster and 40 percent on the orbiter. It was also found that the liftoff thrust to weight ratio (T/W) on the booster-orbiter should be 1.3. This leads to a low dry weight and still provides enough thrust to allow the design of a heavy lift architecture. As a result of another trade study, the dry weight of the reference booster-orbiter was chosen for a variety of operational considerations. Other trade studies on the booster-orbiter demonstrate that the cross feeding of propellant during boost phase is desirable and that engine-out capability from launch to orbit is worth the performance penalty. Technology assumptions made during the Shuttle-2 design were shown to be approx. equivalent to a 25 percent across the board weight reduction over the Space Shuttle technology. The vehicles of the Shuttle-2 architecture were also sized for a wide variety of payloads and missions to different orbits. Many of these same parametric trades were also performed on completely liquid hydrogen fueled fully reusable concepts. If a booster-orbiter is designed using liquid hydrogen engines on both the booster and orbiter, the total vehicle dry weight is only 3.0 percent higher than the reference dual-fuel booster-orbiter, and the gross weight is 3.8 percent less. For this booster-orbiter vehicle, a liftoff T/W of 1.3, a thrust of about 60 percent on the booster, and a Mach staging number of 3 all proved to be desirable. This modest dry weight increase for a liquid hydrogen fueled Shuttle-2 system should be more than offset by the elimination of the entire hydrocarbon engine development program and the savings in operation cost realized by the elimination of an entire fuel type.

Stanley, Douglas O.↗

NASA NTRS1990

Parametric and experimental analysis using a power flow approach

A structural power flow approach for the analysis of structure-borne transmission of vibrations is used to analyze the influence of structural parameters on transmitted power. The parametric analysis is also performed using the Statistical Energy Analysis approach and the results are compared with those obtained using the power flow approach. The advantages of structural power flow analysis are demonstrated by comparing the type of results that are obtained by the two analytical methods. Also, to demonstrate that the power flow results represent a direct physical parameter that can be measured on a typical structure, an experimental study of structural power flow is presented. This experimental study presents results for an L shaped beam for which an available solution was already obtained. Various methods to measure vibrational power flow are compared to study their advantages and disadvantages.

Cuschieri, J. M.↗

NASA NTRS1991

Parametric entry corridors for lunar/Mars aerocapture missions

Parametric atmospheric entry corridor data are presented for Earth and Mars aerocapture. Parameter ranges were dictated by the range of mission designs currently envisioned as possibilities for the Human Exploration Initiative (HEI). This data, while not providing a means for exhaustive evaluation of aerocapture performance, should prove to be a useful aid for preliminary mission design and evaluation. Entry corridors are expressed as ranges of allowable vacuum periapse altitude of the planetary approach hyperbolic orbit, with chart provided for conversion to an approximate flight path angle corridor at entry interface (125 km altitude). The corridor boundaries are defined by open-loop aerocapture trajectories which satisfy boundary constraints while utilizing the full aerodynamic control capability of the vehicle (i.e., full lift-up or full lift-down). Parameters examined were limited to those of greatest importance from an aerocapture performance standpoint, including the approach orbit hyperbolic excess velocity, the vehicle lift to drag ratio, maximum aerodynamic load factor limit, and the apoapse of the target orbit. The impact of the atmospheric density bias uncertainties are also included. The corridor data is presented in graphical format, and examples of the utilization of these graphs for mission design and evaluation are included.

Ling, Lisa M.↗

NASA NTRS1991

Parametric study in weld mismatch of longitudinally welded SSME HPFTP inlet

Welded joints are an essential part of pressure vessels such as the Space Shuttle Main Engine (SSME) Turbopumps. Defects produced in the welding process can be detrimental to weld performance. Recently, review of the SSME high pressure fuel turbopump (HPFTP) titanium inlet x rays revealed several weld discrepancies such as penetrameter density issues, film processing discrepancies, weld width discrepancies, porosity, lack of fusion, and weld offsets. Currently, the sensitivity of welded structures to defects is of concern. From a fatigue standpoint, weld offset may have a serious effect since local yielding, in general, aggravates cyclic stress effects. Therefore, the weld offset issue is considered. Using the finite element method and mathematical formulations, parametric studies were conducted to determine the influence of weld offsets and a variation of weld widths in longitudinally welded cylindrical structures with equal wall thickness on both sides of the joint. From the study, the finite element results and theoretical solutions are presented.

Min, J. B.↗

NASA NTRS1990

Finite element model reduction application to parametric studies and optimization of rotorcraft structures

As a result of this work, a reduction procedure has been developed which can be applied to large finite element model of airframe type structures. This procedure, which is tailored to be used with MSC/NASTRAN finite element code, is applied to the full airframe dynamic finite element model of AH-64A Attack Helicopter. The applicability of the resulting reduced model to parametric and optimization studies is examined. Through application of the design sensitivity analysis, the viability and efficiency of this reduction technique has been demonstrated in a vibration reduction study.

Hashemi-Kia, M.↗

NASA NTRS1991

Robustness in the presence of mixed parametric uncertainty and unmodeled dynamics

Continuing the development of the structured singular value approach to robust control design, the authors investigate the problem of computing the structured singular value (mu) in the case of mixed real parametric and complex uncertainty. The problem is shown to be equivalent to a smooth constrained finite-dimensional optimization problem. In view of the fact that the functional to be maximized may have several local extrema, an upper bound on mu whose computation is numerically tractable is established; this leads to a sufficient condition of robust stability and performance. A historical perspective on the development of the mu theory is included.

Fan, Michael K. H.↗