Search NASA⌕ Search

SEARCH · Search NASA

Results for “recession measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

604 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Numerical Modeling of the Transient Chilldown Process of a Cryogenic Propellant Transfer Line

Before cryogenic fuel depots can be fully realized, efficient methods with which to chill down the spacecraft transfer line and receiver tank are required. This paper presents numerical modeling of the chilldown of a liquid hydrogen tank-to-tank propellant transfer line using the Generalized Fluid System Simulation Program (GFSSP). To compare with data from recently concluded turbulent LH2 chill down experiments, seven different cases were run across a range of inlet liquid temperatures and mass flow rates. Both trickle and pulse chill down methods were simulated. The GFSSP model qualitatively matches external skin mounted temperature readings, but large differences are shown between measured and predicted internal stream temperatures. Discrepancies are attributed to the simplified model correlation used to compute two-phase flow boiling heat transfer. Flow visualization from testing shows that the initial bottoming out of skin mounted sensors corresponds to annular flow, but that considerable time is required for the stream sensor to achieve steady state as the system moves through annular, churn, and bubbly flow. The GFSSP model does adequately well in tracking trends in the data but further work is needed to refine the two-phase flow modeling to better match observed test data.

Temperature Sensors↗
NASA NTRS2026

Development and Experimental Validation of a Path-Dependent Spin Forming Finite Element Model

Spin forming is an advanced manufacturing process widely used in the aerospace and defense sectors to produce lightweight, high-strength cylindrical components with tight dimensional tolerances. This study explores the applicability of the path-dependent Mechanical Threshold Stress (MTS) constitutive model by simulating the evolution of geometry, machining forces, and plastic deformation during the spin forming of a 10-mm thick 6061-O aluminum cylinder. While numerical modeling of spin forming has advanced substantially over the past decade, systematic verification and experimental validation of material models remain limited, particularly in predicting through-thickness process evolution. The MTS model, incorporating a Voce hardening rule, is employed for its ability to represent cyclic loading, rapidly varying temperature fields, and strain rates characteristic of spin forming. Numerical convergence analysis indicates discretization uncertainties between 0.3% and 9.2% for key quantities of interest. Experimental validation demonstrates that the MTS model, when implemented with a verified mesh, accurately reproduces both elastic and plastic behavior of 6061-O aluminum, predicting peak roller loads within 11–18% of measurements, geometric tolerances within 3%, and plastic strain distributions within 10% of experimental values. Collectively, these results establish a validated computational framework for predictive spin-forming simulations with quantified confidence, providing a foundation for extension to other alloys, geometries, and forming conditions.

Spin forming↗
NASA NTRS2026

Thermal Cycle and Capacitance Testing of Mezzo Industries Phase Changer Material Heat Capacitor

Effective Thermal management is essential for the safety and performance of human spacecraft, especially during long-duration missions with fluctuating heat loads. Phase Change Material (PCM) heat exchangers offer a compact, efficient solution by storing and releasing thermal energy through latent heat during phase transitions. This allows PCM systems to buffer transient thermal loads without immediate heat rejection, reducing the need for oversized radiators – particularly critical during ascent and re-entry when radiators are stowed. By maintaining stable temperatures in crew cabins and equipment bays, PCM technology enhances crew comfort, protects sensitive systems, and supports long-term mission sustainability with minimal mass and volume impact. A phase change material heat capacitor prototype, designed and built under a NASA Small Business Innovation Research grant by Mezzo Technologies, utilizes a laser welding microtube manufacturing process that promises increased reliability and performance over current manufacturing methods like brazing. This heat exchanger was tested through coolant thermal cycling within the expected flow rates and temperature range of the Orion spacecraft, the crewed spacecraft taking NASA astronauts to the moon under the Artemis Program. The useful heat storage capacitance was measured and compared to Orion spacecraft requirements.

Active Thermal Control Systems↗
NASA NTRS2026

Effects of Multisensory Virtual Reality Nature on Affect, Presence, and Restorativeness

Virtual reality (VR) can provide access to restorative environments and sensory stimulation for individuals in isolated, confined, and extreme environments. We developed a nature-based VR intervention featuring three scenes (Garden, Forest, Beach) and examined the effects of multisensory augmentation with location-based olfactory, wind, and thermal stimuli (VR+OWT). Over a two-week period, fifty-one participants were assigned to a no-intervention control, standard audiovisual VR, or augmented VR (VR+OWT) condition. Data collection included weekly assessments of affect, stress, and cognitive performance; post-VR measures of affect, presence, and perceived restorativeness; and open-ended feedback. Both VR and VR+OWT groups produced immediate and sustained reductions in negative affect with no sustained systematic benefits on cognitive performance. The addition of olfactory, wind, and thermal stimuli enhanced presence for some scenes; however, feedback indicated that sensory mismatches and stimulus intensity occasionally detracted from the experience and may have contributed to lower coherence ratings in the VR+OWT group. In contrast, the perceived restorativeness of the VR environment was driven primarily by scene content (Garden vs Forest vs Beach) rather than the level of sensory stimulation. These findings support the potential of virtual nature to promote well-being and underscore the importance of coherence across sensory modalities for multisensory augmentation.

Virtual Reality Intervention↗
NASA NTRS2026

Isotopic Evidence for A Cold and Distant Origin of 3I/Atlas

Interstellar objects provide the only directly observable samples of icy planetesimals formed around other stars, and can therefore provide insight into the diversity of physical and chemical conditions occurring during exoplanet formation1−3. Here we report isotopic measurements of the interstellar comet 3I/ATLAS, which reveal an elemental composition unlike any Solar System body. The water in 3I/ATLAS is enriched in deuterium, at a level of D/H = (0.98 ± 0.06)%, which is more than an order of magnitude higher than in known comets, while its range of 12 C/ 13 C ratios (141–191 for CO 2 and 123–172 for CO) exceeds typical values found in the Solar System, as well as nearby interstellar clouds and protoplanetary disks. Such extreme isotopic signatures indicate formation at temperatures ≲ 30 K in a relatively metal-poor environment. When interpreted with respect to models for Galactic chemical evolution, the carbon isotopic composition implies that 3I/ATLAS may have accreted as long ago as 12 billion years, following a period of intense, early star formation. 3I/ATLAS thus represents a preserved fragment of an ancient planetary system.

Martin A Cordiner↗
DOE OSTI2024

Optimizing Deep Geothermal Drilling for Energy Sustainability in the Appalachian Basin

This study investigates the geological and geomechanical characteristics of the MIP 1S geothermal well in the Appalachian Basin to optimize drilling and address the wellbore stability issues encountered. Data from well logs, sidewall core analysis, and injection tests were used to derive elastic and rock strength properties, as well as stress and pore pressure profiles. A robust 1D-geomechanical model was developed and validated, correlating strongly with wellbore instability observations. This revealed significant wellbore breakout, widening the diameter from 12 ¼ inches to over 16 inches. Advanced technologies like Cerebro Force™ In-Bit Sensing were used to monitor drilling performance with high accuracy. This technology tracks critical metrics such as bit acceleration, vibration in the x, y, and z directions, Gyro RPM, stick-slip indicators, and bending on the bit. Cerebro Force™ readings identified hole drag caused by poor hole conditions, including friction between the drill string and wellbore walls and the presence of cuttings or debris. This led to higher torque and weight on bit (WOB) readings at the surface compared to downhole measurements, affecting drilling efficiency and wellbore stability. Optimal drilling parameters for future deep geothermal wells were determined based on these findings.

Environmental Sciences & Ecology↗
DOE OSTI2026

Oversizing and Part-Load Problems

Oversizing, the common engineering practice of specifying devices with capacity exceeding the actual load requirement, is a widespread practice across virtually all building technologies end-use categories, including HVAC, electrical systems, lighting, appliances, and plug loads. This practice, driven by factors like design uncertainty, institutional pressures, and risk aversion, results in wasted capital investment, control difficulties, and excessive energy consumption due to inefficient part-load operation. Part-load operation, where devices run below maximum capacity, is the dominant operating mode in most energy systems and presents a complex design challenge. Solutions to match output to load fall into three broad categories: constraining the output, adjusting the device’s internal behavior, and linking output to energy storage or other waste-heat reuse applications. The energy implications of part-load are critical, as efficiency often drops sharply as load decreases across a wide diversity of devices. To quantify the extent of this problem, we derive a dimensionless Part-Load Metric (PLM) based on device efficiency and its frequency distribution of operating hours at various output levels. The PLM quantifies the deviation of a device's actual efficiency from its maximum design efficiency. This metric also serves as a measure of "capital inefficiency," enabling engineers to compare the impact of different part-load solutions and providing a unified framework for evaluating performance across various devices and systems.

Meier, Alan↗
DOE OSTI2026

Mechanics and Cooling of the CMS Phase-II Tracker Barrel

The CMS upgrade for the High-Luminosity LHC (HL-LHC) era will allow for an incredibly high rate of data collection, to be used in the next generation of precision measurements and searches for beyond the standard model physics. A key element of this upgrade is the full replacement of the silicon strip tracker to enable level-1 triggering on track level primitives, produced by pixel-strip (PS) and strip-strip (2S) modules, tiled together to form the new detector. Mechanically supporting and cooling these modules is not trivial, as material budget in the tracker volume is highly constrained, and as the modules accrue radiation damage they risk becoming entirely non-functional if the silicon sensors are not sufficiently cooled. To address this, each region of the tracker has a bespoke solution for housing and cooling their modules, mostly depending on carbon-fiber and carbon-foam structures, with dual phase CO2 cooling. For the most central part of the tracker, the Flat Barrel with PS modules (Flat TBPS) covers the pseudorapidity range out to $|\eta|=0.4$, and the mechanical structures are manufactured, assembled, and tested entirely by Fermilab and UC Davis. This presentation will describe the intense design and testing requirements for these components, and how they will ensure strong performance of the tracker through the HL-LHC era.

Cosby, Christopher [Fermilab]↗
NASA NTRS1985

Suppression of Marangoni Convection in Float Zones

The basic purpose of this program is to demonstrate by means of an Earth-based 1-g experiment that the undesirable Marangoni (surface tension) convection can be suppressed or significantly reduced by means of gas jets directed tangentially to the free surface of the liquid in a float zone. These jets will establish the tangential shear stress field over the surface which must be adjusted to equal the counter-stress resultant of the Marangoni shear stress which causes the convection. For proposed materials processing in space (o-g), particularly of important, highly reactive semiconductor materials, e.g., silicon, microgravity will virtually eliminate the unwanted thermal-buoyancy convection in the liquid silicon, but will have no effect in reducing the Marangoni convection. Unless this can be sufficiently suppressed by other means, there may be no significant advantages to the proposed space processing of reactive semiconductors. Although some inert gas such as argon must be used for the corrosive liquid silicon, the Earth-based experiment uses air jets and various transparent oils, since the basic principle involved is the same. The first float zone is enclosed in a very small rectangular box with a quasi-planar free surface. Stable Marangoni convection has been achieved and velocities measured photographically. The air jet system with variable velocity and temperature is under construction. Three independent parameters must be optimized to attain maximum suppression: the gas velocity, angle of attack, and gas temperature.

Robert F Dressler↗
NASA NTRS2026

Impact Testing of 410 Stainless Steel for Material Impact Model Development

A project is underway to develop a consistent set of material properties, impact test data, and failure analysis for a variety of metallic aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration William J. Hughes Technical Center. Particular features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all the raw data are available. Four parallel efforts are currently underway: measurement of material deformation and failure response over a wide range of strain rates and temperatures, failure analysis of material property specimens and impact test articles, development of improved numerical modeling techniques for deformation and failure, and impact testing of flat panels and substructures for model validation. This report describes impact testing performed on 410 stainless steel sheet and plate samples of different thicknesses with two different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

410 Stainless Steel↗
NASA NTRS2026

Glenn Research Center Propulsion Systems Laboratory 2026 Customer Guide

This guide describes the Propulsion Systems Laboratory (PSL) at the NASA Glenn Research Center. It was written to help customers understand the various components involved in conducting a test program within the PSL. The PSL complex supports two large-engine test cells that simulate altitude flight conditions for a wide range of research and experimental tests. These test cells operate at altitudes up to 90,000 ft and speeds from subsonic to above supersonic. Test points such as pressure, temperature, and Mach number can be set at the engine or test article inlet based on customer requirements. The facility’s support systems include the heated and cooled combustion air systems; altitude exhaust system; hydraulic system; nitrogen, oxygen, and hydrogen systems; thrust measurement system, which includes the facility’s single- and multi-axis thrust stands; inlet system; and electrical systems. In addition to providing a detailed description of PSL systems and capabilities, this guide discusses the facility’s history and past tests and addresses facility safety procedures, pretest requirements, and test operation standards.

Engine Icing Test Facility↗
DOE OSTI2026

Enter the AHU (36th Chamber of ASHRAE): A Multi-site Field Study of ASHRAE G36

Despite being recognized as the best practice for advanced building controls, ASHRAE Guideline 36 (G36) has seen slow adoption in retrofit cases. Decisionmakers lack credible field evidence to justify the time and person-power investment. Most prior analyses have relied on software simulations, which overlook implementation challenges and fail to persuade owners to move from models to real-world deployment. This paper presents a multi-site field study of G36 performance, drawing on measured results from 17 projects across diverse building types and climate zones. The analysis disaggregates outcomes by the most widely adopted air handling unit (AHU) based G36 strategies, including trim-and-respond approaches to supply air temperature (SAT) and duct static pressure (DSP) reset, and economizer controls. Results for controls re programming implementations are encouraging, with HVAC savings ranging from 2% - 49%, with a median of 18%. The range aligns with simulation study findings showing 1% - 46% savings through these three strategies. These findings show that even without capital investment in control infrastructure upgrades, existing building owners are reaping significant benefits from updating HVAC sequences of operation to industry best-practice solutions. The results give practitioners and decisionmakers a reference point on what to expect, which strategies deliver, and how field performance may compare to simulation.

Deshpande, Reva↗
DOE OSTI2025

Strong anharmonicity dictates ultralow thermal conductivities of type-I clathrates

Type-I clathrate solids have attracted significant interest due to their ultralow thermal conductivities and sub- sequent promise for thermoelectric applications, yet the mechanisms underlying these properties are not well understood. Here, we extend the framework of vibrational dynamical mean-field theory (VDMFT) to calculate temperature-dependent thermal transport properties of solids using a many-body Green’s function approach. When applied to a coarse-grained description of 𝑋 8 Ga 16 Ge 30 , where 𝑋= Ba, Sr, we find that nonresonant scattering between cage acoustic modes and rattling modes leads to a reduction of acoustic phonon lifetimes and thus thermal conductivities. Moreover, we find that the moderate temperature dependence of conductivities above 300 K, which is consistent with experimental measurements, cannot be reproduced by textbook perturbation theory calculations, which predict a 𝑇 −1 dependence. Therefore, we suggest that nonperturbative anharmonic effects, including four- and higher-phonon scattering processes, are responsible for the ultralow thermal conductivities of type-I clathrates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

ORNL Report of Analysis for the Verification of NRMP CRM U030A

In support of the Certified Reference Material (CRM) program managed by the Nuclear Reference Material Program (NRMP), the Material Signatures and Isotopic Standards (MSIS) group of Oak Ridge National Laboratory (ORNL) was asked to prepare a set of CRM U030A units for use as standards for isotopic analysis using multicollector thermal ionization mass spectrometry (TIMS) and inductively coupled plasma mass spectrometry (ICP-MS) instruments. This report documents the results of the verification measurements performed on three randomly selected units by the MSIS group’s ISO/IEC 17025:2017 accredited operating procedure CSD-AM-CIMS-IN20, Determination of Uranium and Plutonium Isotopic Composition using Thermal Ionization Mass Spectrometry [1], and in accordance with the quality assurance plan as described in QAP-X-96-CSD/RML-001, Nuclear Analytical Chemistry Laboratory Section Quality Assurance Plan [2].

Mathew, Kattathu [Oak Ridge National Laboratory (O↗
DOE OSTI2026

Anomalous lattice expansion of bcc Ta in helium-loaded diamond anvil cells

Anomalous lattice expansion of bcc Ta is observed in helium-loaded diamond anvil cell (DAC) experiments near 6 GPa and above 400 K, while co-loaded W, Mo, and Au exhibit normal thermal expansion. The Ta volume expansion increases with temperature, reaching ~14% near 650 K before plateauing, and is largely retained after recovery to ambient conditions. Time-resolved measurements at 500 K reveal progressive expansion over several hours, consistent with gradual, thermally activated He incorporation. The largely retained expansion during subsequent cooling and holding at 400 K indicates that the incorporated He is predominantly kinetically trapped. The data reveal two distinct regimes: below ~550 K, modest and spatially uniform expansion consistent with interstitial He trapping at isolated, randomly distributed vacancies; above ~550 K, He-vacancy cluster growth producing dramatically larger expansion, peak broadening, and a core–shell microstructure revealed by micron-resolution X-ray diffraction mapping. These results demonstrate that He is not always a passive pressure medium in DAC experiments and reveal a previously unrecognized regime of He-mediated lattice modification in Ta, complementing conventional ion-implantation studies relevant to nuclear and fusion structural materials.

Diamond anvil cell↗
DOE OSTI2025

Blockage effects in the chemotaxis of diffusiophoretic particles

Transport mechanisms at the micro- and nano-scale play an essential role in regulating intracellular organization. Recent work indicates that directed motion of constituents inside cells can emerge through diffusiophoretic transport, in which colloidal particles move under the influence of chemical gradients. Here, we examine how blockers—passive or actively consuming—reshape those gradients and thereby influence the motion of diffusiophoretic particles. By combining analytical solutions with finite element simulations, we first show that a single blocker can distort a background gradient enough to create or eliminate stagnation points, significantly modifying particle transport. We then introduce a second, explicitly sized blocker at one of these stagnation points and measure how its finite radius alters the diffusiophoretic velocity field for a test particle. Even moderate changes in the second blockers size can cause noticeable shifts in the substrate distribution, highlighting the importance of accounting for explicit particle radii under crowded or consumption-driven conditions. Our findings underscore that subtle geometric variations—such as the radii and positions of two or more blockers—can profoundly affect diffusiophoretic motion, providing a more complete picture of how blocking and crowding phenomena shape intracellular transport.

Song, Zehao [Northwestern Univ., Evanston, IL (Uni↗
DOE OSTI2026

Unveiling field-transverse spin anisotropy in the spin liquid candidate α-RuCl3 via spin Hall magnetoresistance

α-RuCl3 has emerged as a possible candidate for a quantum spin liquid (QSL) that promises exotic quasiparticles relevant for fault-tolerant quantum computation. Here, we report spin-sensitive transport measurements using a proximal spin Hall metal, platinum (Pt), to probe magnetic moments in the insulator α-RuCl3. We observe spin Hall magnetoresistance (SMR), where both the transverse and longitudinal resistivities exhibit angular oscillations between the in-plane magnetic field and the current, driven by the interplay between the spin Hall effect in Pt and local magnetic moments in α-RuCl3. These oscillations occur from 1.5 to 18 T, covering the zigzag antiferromagnetic, putative QSL, and supposedly partially field-polarized phases. The phase of the SMR oscillations suggests that the local moments, whether static or fluctuating, develop spin anisotropy with a quantization axis in-plane and largely transverse to the magnetic field across all fields from 1.5 to 18 T. Temperature dependence indicates that the spin anisotropy operates at an energy scale similar to that of the reported QSL signatures in α-RuCl3.

Idzuchi, Hiroshi [Tohoku University, Japan]↗
DOE OSTI2025

Decoupling thermal and irradiation effects on grain boundary segregation

Radiation-induced segregation (RIS) is most often measured by peak solute concentration at a boundary. However, this may give an incomplete picture of segregation quantity and phenomena. Radiation-induced and thermal segregation at grain boundaries was investigated in Fe-9.6 at.% Cr after 9 MeV Fe 3+ ion irradiation at 400 °C. The experimental results were compared to kinetic Monte Carlo (KMC) simulations. The study revealed that Cr enrichment (peak segregation) at the grain boundaries was comparable in both the irradiated and non-irradiated conditions, although irradiation resulted in broader segregation profiles in both experiments and simulations, indicating an overall increase in grain boundary segregation due to irradiation. This broadening is attributed to back diffusion into the grain interior. While it is an established phenomenon, this study offers a quantitative evaluation using experimental data and KMC modeling. Further, these results emphasize the importance of analyzing the entire segregation profile and decoupling the thermal and irradiation contributions to solute segregation.

Grain boundary segregation↗