Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface steps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Effect of phase separation induced supercooling on magnetotransport properties of epitaxial La{sub 5/8−y}Pr{sub y}Ca{sub 3/8}MnO{sub 3} (y≈0.4) thin film

Thin films of La{sub 5/8−y}Pr{sub y}Ca{sub 3/8}MnO{sub 3} (y≈0.4) have been grown on single crystal SrTiO{sub 3} (001) by RF sputtering. The structural and surface characterizations confirm the epitaxial nature of these film. However, the difference between the ω-scan of the (002) and (110) peaks and the presence of pits/holes in the step-terrace type surface morphology suggests high density of defect in these films. Pronounced hysteresis between the field cooled cooling (FCC) and field cooled warming (FCW) magnetization measurements suggest towards the non-ergodic magnetic state. The origin of this nonergodicity could be traced to the magnetic liquid like state arising from the delicacy of the coexisting magnetic phases, viz., ferromagnetic and antiferromagnetic-charge ordered (FM/AFM-CO). The large difference between the insulator metal transitions during cooling and warming cycles (T{sub IM}{sup C} ∼ 64 K and T{sub IM}{sup W} ∼ 123 K) could be regarded as a manifestation of the nonergodicity leading to supercooling of the magnetic liquid while cooling. The nonergodicity and supercooling are weakened by the AFM-FM phase transition induced by an external magnetic field. T{sub IM} and small polaron activation energy corresponding the magnetic liquid state (cooling cycle) vary nonlinearly with the applied magnetic field but become linear in the crystalline solid state (warming cycle). The analysis of the low temperature resistivity data shows that electron-phonon interaction is drastically reduced by the applied magnetic field. The resistivity minimum in the lower temperature region of the self-field warming curve has been explained in terms of the Kondo like scattering in the magnetically inhomogeneous regime.

36 MATERIALS SCIENCE↗

Spectroscopic evidence for spin-polarized silicon atoms on Si(553)-Au

The stepped Si(553)-Au surface undergoes a $1\times3$ reconstruction at low temperature which has recently been interpreted theoretically as the $\times3$ ordering of spin-polarized silicon atoms along a step edge in each surface unit cell. This predicted magnetic ground state has a clear spectroscopic signature---a silicon step-edge state at $0.5$ eV above the Fermi level---that arises from strong exchange splitting and hence would not occur without spin polarization. Here we report spatially resolved scanning tunneling spectroscopy data for Si(553)-Au that reveal key differences in the unoccupied step-edge density of states between room temperature and $40$ K. At low temperature we find an unoccupied state at 0.55 eV above every third step-edge silicon atom, in excellent agreement with the spin-polarized ground state predicted theoretically.

Snijders, Paul C↗

Theory Aided Design of Active and Durable Nanoscale Cathode Catalysts (Final Report)

One of the greatest technological hurdles to deployment of fuel cells relates to the sluggish activity, low durability and the high cost of the catalysts that are currently employed. For automotive PEM fuel cells to become commercially viable, the Pt-specific power density would need to be reduced to less than 0.2gPt/kW (at cell voltages >0.65 V). This would require the Pt loadings to be less than 0.15 mg Pt /cm 2 MEA within the membrane electrode assembly. This could be achieved by enhancing the catalytic activity at the cathode, thus lowering its overpotential. Various different Pt-alloys have shown 2-4 times enhanced activities over Pt alone but still suffer some of the same durability issues as that of the pure Pt. There is a general loss of active Pt due to dissolution and sintering. While there have been a number of elegant fundamental experimental and theoretical studies on ideal single crystal Pt and Pt alloy surfaces which have helped to elucidate the factors that control the activity, there have been very few fundamental studies focused on the stability, reactivity and durability of well-defined Pt nanoparticles. We carried out ab initio density functional theory together with a novel double reference method that we developed to simulate constant potential electrochemical systems in order to model the electrocatalytic reduction of oxygen over model Pt alloy surfaces and nanoparticles. These simulations were used to probe the factors that control the electrocatalytic activity, guide the potential selection of new materials and test their stability under reaction conditions. Ab initio calculations were used to determine the reaction energies and activation barriers for a comprehensive array of different elementary adsorption, desorption, surface reaction and diffusion steps over Pt and Pt alloys involved in the electroreduction of oxygen as a function of surface coverage, the electrochemical potential and temperature. The calculations were used to simulate the potential dependent adsorption and surface reaction energies along with activation barriers in order to determine the kinetics for different surface structures and structural features (step edge and corner sites) to provide the necessary input for kinetic Monte Carlo simulations to follow the rates of reaction. More coarse-grained simulated annealing methods were used to help establish the lowest energy structures and morphologies for different Pt and Pt-alloy nanoparticles that form. The results from the DFT calculations were used to establish an ab initio-derived kinetic database that was used in both 2D and 3D kinetic Monte Carlo simulations that were used to follow the electrocatalytic performance over different particle sizes, shapes and compositions. The ab initio calculations together with the kinetic Monte Carlo simulations were used to complete the following objectives: 1) Determine the controlling elementary reaction pathways and intrinsic kinetics involved in ORR and their potential dependent behavior; 2) Establish the influence of the extrinsic reaction environment including surface structure, alloy composition and spatial arrangement and the humidity on ORR kinetics; 3) Elucidate the effects of particle size and morphology as well as the atomic structure and composition of nanoparticles of Pt, Pt 3 Co, Pt 3 Ni, Pt 3 Fe and other Pt-alloys on the electrocatalytic activity and reaction selectivity; 5) Construct surface Pourbaix phase diagrams for different Pt and Pt-alloys in order to map out the most stable surface phases for different material compositions and reaction conditions; 6) Elucidate the mechanisms that control dissolution and re-deposition of Pt.

08 HYDROGEN↗

Site heterogeneity and broad surface-binding isotherms in modern catalysis: Building intuition beyond the Sabatier principle

Learning the science of heterogeneous catalysis and electrocatalysis always starts with the simple case of a flat, uniform surface with an ideal adsorbate. It has of course been recognized for a century that real catalysts are more complicated. For the increasingly complex catalysts of the 21st century, this Perspective argues that surface heterogeneity and non-ideal binding isotherms are central features, and their implications need to be incorporated in current thinking. A variety of systems are described herein where catalyst complexity leads to broad, non-Langmuirian surface isotherms for the binding of hydrogen atoms – and this occurs even for ideal, flat Pt(111) surfaces. Modern catalysis employs nanoscale materials whose surfaces have substantial step, edge, corner, impurity, and other defect sites, and they increasingly have both metallic and non-metallic elements M n X m , including metal oxides, chalcogenides, pnictides, carbides, doped carbons, etc. The surfaces of such catalysts are often not crystal facets of the bulk phase underneath, and they typically have a variety of potential active sites. Catalytic surfaces in operando are often non-stoichiometric, amorphous, dynamic, and impure, and often vary from one part of the surface to another. Understanding of the issues that arise at such nanoscale, multi-element catalysts is just beginning to emerge. Yet these catalysts are widely discussed using Brønsted/Bell-Evans-Polanyi (BEP) relations, volcano plots, Tafel slopes, the Butler-Volmer equation, and other linear free energy relations (LFERs), which all depend on the implicit assumption that the active sites are “similar” and that surface adsorption is close to ideal. These assumptions underly the ubiquitous intuition based on the Sabatier Principle, that the fastest catalysis will occur when key intermediates have free energies of adsorption that are not too strong nor too weak. Current catalysis research often aims to minimize the complexity of non-ideal isotherms through experimental and computational design (e.g., the use of single crystal surfaces), and these studies are the foundation of the field. In contrast, this Perspective argues that the heterogeneity of binding sites and binding energies is an inherent strength of these catalysts. Here, this diversity makes many nanoscale catalysts inherently a high-throughput screen wrapped in a tiny package. Only by making the heterogeneity part of the foundation of catalysis models, sorting the types of active sites and dissecting non-ideal binding isotherms, will modern catalysis learn to harness the inherent diversity of real catalysts. Controlling and exploiting diversity rather than avoiding it will help to optimize complex modern catalysts and catalytic conditions.

Mayer, James M.↗

Surfactant-assisted one-pot sample preparation for label-free single-cell proteomics

Large numbers of cells are generally required for quantitative global proteome profiling due to surface adsorption losses associated with sample processing. Such bulk measurement obscures important cell-to-cell variability (cell heterogeneity) and makes proteomic profiling impossible for rare cell populations (e.g., circulating tumor cells (CTCs)). Here we report a surfactant-assisted one-pot sample preparation coupled with mass spectrometry (MS) method termed SOP-MS for label-free global single-cell proteomics. SOP-MS capitalizes on the combination of a MS-compatible nonionic surfactant, n-Dodecyl-β-D-maltoside, and hydrophobic surface-based low-bind tubes or multi-well plates for ‘all-in-one’ one-pot sample preparation. This ‘all-in-one’ method including elimination of all sample transfer steps maximally reduces surface adsorption losses for effective processing of single cells, thus improving detection sensitivity for single-cell proteomics. This method allows convenient label-free quantification of hundreds of proteins from single human cells and ~1200 proteins from small tissue sections (close to ~20 cells). When applied to a patient CTC-derived xenograft (PCDX) model at the single-cell resolution, SOP-MS can reveal distinct protein signatures between primary tumor cells and early metastatic lung cells, which are related to the selection pressure of anti-tumor immunity during breast cancer metastasis. The approach paves the way for routine, precise, quantitative single-cell proteomics.

36 MATERIALS SCIENCE↗

Molecular-Level Design of Heterogeneous Chiral Catalysis

The following is a proposal to continue our multi-institutional research on heterogeneous chiral catalysis. Our team combines the use of surface-sensitive analytical techniques for the characterization of model systems with quantum and statistical mechanical calculations to interpret experimental data and guide the design of future research. Our investigation focuses on the interrelation among the three main mechanisms by which enantioselectivity can be bestowed to heterogeneous catalysts, namely: (1) by templating chirality via the adsorption of chiral supramolecular assemblies, (2) by using chiral modifiers capable of forming chiral complexes with the reactant and force enantioselective surface reactions, and (3) by forming naturally chiral surfaces using imprinting chiral agents. Individually, the members of our team are leaders in these various aspects of chiral catalysis, but the present program provides the vehicle to generate and exploit the synergies necessary to address the problem in a comprehensive manner. Our initial work has advanced the methodology needed for these studies, including an enantioselective titration procedure to identify surface chiral sites, infrared spectroscopy in situ at the interface between gases or liquids and solids to mimic realistic catalytic conditions, and DFT and Monte Carlo algorithms to simulate and understand chirality on surfaces. The next step, to be funded by the monies requested in this proposal, is to apply those methods to specific problems in chiral catalysis, including the identification of the requirements for the formation of supramolecular surface structures with enantioselective behavior, the search for better molecules to probe the chiral nature of the modified surfaces, the exploration of the transition from supramolecular to one-to-one chiral modification, the correlation of the adsorption characteristics of one-to-one chiral modifiers with their physical properties, in particular with their configuration, and the development of ways to imprint chiral centers on achiral solid surfaces. Chiral catalysis is not only a problem of great importance in its own right, but also the ultimate test of how to control selectivity in catalysis. The time is ripe for fundamental work in heterogeneous chiral catalysis to provide the U.S. with a leadership role in developing the next generation of catalytic processes for medicinal and agrochemical manufacturing. Our team provides the required expertise for a synergistic and comprehensive integration of physical and chemical experimentation with solid state and molecular reactivity theories to solve this problem.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Atomically Flat Surfaces Developed for Improved Semiconductor Devices

New wide bandgap semiconductor materials are being developed to meet the diverse high temperature, -power, and -frequency demands of the aerospace industry. Two of the most promising emerging materials are silicon carbide (SiC) for high-temperature and high power applications and gallium nitride (GaN) for high-frequency and optical (blue-light-emitting diodes and lasers) applications. This past year Glenn scientists implemented a NASA-patented crystal growth process for producing arrays of device-size mesas whose tops are atomically flat (i.e., step-free). It is expected that these mesas can be used for fabricating SiC and GaN devices with major improvements in performance and lifetime. The promising new SiC and GaN devices are fabricated in thin-crystal films (known as epi films) that are grown on commercial single-crystal SiC wafers. At this time, no commercial GaN wafers exist. Crystal defects, known as screw defects and micropipes, that are present in the commercial SiC wafers propagate into the epi films and degrade the performance and lifetime of subsequently fabricated devices. The new technology isolates the screw defects in a small percentage of small device-size mesas on the surface of commercial SiC wafers. This enables atomically flat surfaces to be grown on the remaining defect-free mesas. We believe that the atomically flat mesas can also be used to grow GaN epi films with a much lower defect density than in the GaN epi films currently being grown. Much improved devices are expected from these improved low-defect epi films. Surface-sensitive SiC devices such as Schottky diodes and field effect transistors should benefit from atomically flat substrates. Also, we believe that the atomically flat SiC surface will be an ideal surface on which to fabricate nanoscale sensors and devices. The process for achieving atomically flat surfaces is illustrated. The surface steps present on the "as-received" commercial SiC wafer is also illustrated. because of the small tilt angle between the crystal "basal" plane and the polished wafer surface. These steps are used in normal SiC epi film growth in a process known as stepflow growth to produce material for device fabrication. In the new process, the first step is to etch an array of mesas on the SiC wafer top surface. Then, epi film growth is carried out in the step flow fashion until all steps have grown themselves out of existence on each defect-free mesa. If the size of the mesas is sufficiently small (about 0.1 by 0.1 mm), then only a small percentage of the mesas will contain an undesired screw defect. Mesas with screw defects supply steps during the growth process, allowing a rough surface with unwanted hillocks to form on the mesa. The improvement in SiC epi surface morphology achievable with the new technology is shown. An atomic force microscope image of a typical SiC commercial epilayer surface is also shown. A similar image of an SiC atomically flat epi surface grown in a Glenn laboratory is given. With the current screw defect density of commercial wafers (about 5000 defects/cm2), the yield of atomically free 0.1 by 0.l mm mesas is expected to be about 90 percent. This is large enough for many types of electronic and optical devices. The implementation of this new technology was recently published in Applied Physics Letters. This work was initially carried out in-house under a Director's Discretionary Fund project and is currently being further developed under the Information Technology Base Program.

Powell, J. Anthony↗

Thermographic monitoring of materials under simulated reentry conditions

Thermography can be used to measure surface temperature gradients graphically, and can be used under conditions where the direct measurement of temperature at all desired points, using thermocouples or resistance temperature detectors (RTDs), is either difficult or impossible. The use of thermographic monitoring during a series of arc-jet tests is described. Described in this work are the issues that influence interpretation of the thermographic measurements under these conditions, including the calculation of effective emittance and window transmittance from the spectral properties of the materials in order to calculate the temperature distribution of a surface directly from the measured radiance. Comparison of the surface temperatures measured using thermocouples and the temperatures derived from thermographic measurements show good agreement. The data gathered will be used to evaluate important test parameters such as the heating distribution across the surface of a heat shield test model and at steps on the model surface.

White, Susan M.↗

A new algorithm for three‐dimensional joint inversion of body wave and surface wave data and its application to the Southern California plate boundary region

Abstract We introduce a new algorithm for joint inversion of body wave and surface wave data to get better 3‐D P wave ( V p ) and S wave ( V s ) velocity models by taking advantage of the complementary strengths of each data set. Our joint inversion algorithm uses a one‐step inversion of surface wave traveltime measurements at different periods for 3‐D V s and V p models without constructing the intermediate phase or group velocity maps. This allows a more straightforward modeling of surface wave traveltime data with the body wave arrival times. We take into consideration the sensitivity of surface wave data with respect to V p in addition to its large sensitivity to V s , which means both models are constrained by two different data types. The method is applied to determine 3‐D crustal V p and V s models using body wave and Rayleigh wave data in the Southern California plate boundary region, which has previously been studied with both double‐difference tomography method using body wave arrival times and ambient noise tomography method with Rayleigh and Love wave group velocity dispersion measurements. Our approach creates self‐consistent and unique models with no prominent gaps, with Rayleigh wave data resolving shallow and large‐scale features and body wave data constraining relatively deeper structures where their ray coverage is good. The velocity model from the joint inversion is consistent with local geological structures and produces better fits to observed seismic waveforms than the current Southern California Earthquake Center (SCEC) model.

Fang, Hongjian↗

Predicting Pulsed-Laser Deposition SrTiO 3 Homoepitaxy Growth Dynamics Using High-Speed Reflection High-Energy Electron Diffraction

Pulsed-laser deposition (PLD) is a powerful technique for growing complex oxides with controlled stoichiometry. To understand growth dynamics therein, it is common to leverage in situ spectroscopies, such as reflection high-energy electron diffraction (RHEED), to monitor surface crystallinity. Most commercial systems rely on video-rate cameras operating at 60-120 Hz that lack sufficient temporal resolution to capture growth dynamics at practical deposition frequencies. Here, a high-speed platform to record in situ dynamics via RHEED at >500 Hz is implemented. An open-source analysis package is designed to fit diffraction spots to 2D Gaussians, allowing single-pulse surface reconstruction kinetics extraction. Using homoepitaxially deposited (001)-oriented SrTiO 3 as a model system, we demonstrate how high-speed RHEED can provide real-time insight into growth processes obscured by slower acquisition systems. By fitting the single-pulse intensity to a set of exponential functions, we observe changes in the characteristic decay time and mechanism correlated to the substrate step width and surface termination. We observe distinct surface effects, with diffraction intensity decaying on lower-energy TiO 2 -terminated surfaces and stabilizing on SrO- or mixed-terminated surfaces. Similarly, using an exponential model, the extracted characteristic time of adatom deposition decreases with increased density of bonding sites associated with mixed termination and narrower step widths. Ultimately, this work shows how increasing RHEED temporal resolution can uncover new insights into growth processes, with practical implications for the design and control of PLD processes. This experimental platform provides new capabilities to enable data-driven machine learning analysis and autonomous control systems to enhance the complexity and fecundity of PLD.

(SrO)↗

Effect of Material Structure on Photoluminescence of ZnO/MgO Core-Shell Nanowires

Zinc oxide (ZnO) nanowires are widely studied for use in ultraviolet optoelectronic devices, such as nanolasers and sensors. Nanowires (NWs) with an MgO shell exhibit enhanced band-edge photoluminescence (PL), a result previously attributed to passivation of ZnO defects. However, we find that processing the ZnO NWs under low oxygen partial pressure leads to an MgO-thickness-dependent PL enhancement owing to the formation of optical cavity modes. Conversely, processing under higher oxygen partial pressure leads to NWs that support neither mode formation nor band-edge PL enhancement. High-resolution electron microscopy and density-functional calculations implicate the ZnO m-plane surface morphology as the key determinant of core-shell structure and cavity-mode optics. A ZnO surface with atomic steps along the m-plane in the c-axis direction stimulates the growth of a smooth MgO shell that supports guided-wave optical modes and enhanced UV PL. On the other hand, a smoother ZnO surface leads to nucleation of a rough cladding layer which supports neither enhanced UV PL nor optical cavity modes. Finite-element analysis shows a clear correlation between allowed Fabry-Perot and whispering gallery modes and enhanced UV-PL. Finally, these results point the way to fabricating ZnO/MgO core-shell nanowires for more efficient UV nanolasers, scintillators, and sensors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Reaction processes at step edges on S-decorated Cu(111) and Ag(111) surfaces: MD analysis utilizing machine learning derived potentials

We report a variety of complexation, reconstruction, and sulfide formation processes can occur at step edges on the {111} surfaces of coinage metals (M) in the presence of adsorbed S under ultra-high vacuum conditions. Given the cooperative many-atom nature of these reaction processes, Molecular Dynamics (MD) simulation of the associated dynamics is instructive. However, only quite restricted Density Functional Theory (DFT)-level ab initio MD is viable. Thus, for M = Ag and Cu, we instead utilize the DeePMD framework to develop machine-learning derived potentials, retaining near-DFT accuracy for the M–S systems, which should have broad applicability. These potentials are validated by comparison with DFT predictions for various key quantities related to the energetics of S on M(111) surfaces. The potentials are then utilized to perform extensive MD simulations elucidating the above diverse restructuring and reaction processes at step edges. Key observations from MD simulations include the formation of small metal–sulfur complexes, especially MS 2 ; development of a local reconstruction at A-steps featuring an S-decorated {100} motif; and 3D sulfide formation. Additional analysis yields further information on the kinetics for metal–sulfur complex formation, where these complexes can strongly enhance surface mass transport, and on the propensity for sulfide formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Gold-Tin Solder Wetting Behavior for Package Lid Seals

This study examined the cause of nonwetted regions of the gold (Au) finish on iron-nickel (Fe–Ni) alloy lids that seal ceramic packages using the 80Au-20Sn solder (wt %, abbreviated Au–Sn) and their impact on the final lid-to-ceramic frame solder joint. The Auger electron spectroscopy (AES) surface and depth profile techniques identified surface and through-thickness contaminants in the Au metallization layer. In one case, the AES analysis identified background levels of carbon (C) contamination on the surface; however, the depth profile detected Fe and Ni contaminants that originated from the plating process. The Fe and Ni could impede the completion of wetting and spreading to the edge of the Au metallization. The Au layer of lids not exposed to a Au–Sn solder reflow step had significant surface and through-thickness C contamination. Inorganic contaminants were absent. Subsequent simulated reflow processes removed the C contamination from the Au layer without driving Ni diffusion from the underlying solderable layer. Finally, an Au metallization having negligible C contamination developed elevated C levels after exposure to a simulated reflow process due to C contamination diffusing into it from the underlying Ni layer. However, the second reflow step removed that contamination from the Au layer, thereby allowing the metallization to support the formation of lid-to-ceramic frame Au–Sn joints without risk to their mechanical strength or hermeticity.

36 MATERIALS SCIENCE↗

The response of turbulent boundary layers to sudden pertubations

The processes present in a turbulent boundary layer (BL) which experiences a sudden change in the surface roughness are discussed in terms of numerical models in comparison with empirical data. Consideration is limited to flow perturbations which preserve the BL approximation. Generalized continuity, momentum and turbulent energy transport equations are reviewed. The perturbed BL has two regions: one with large velocity gradients and an outer zone with smaller gradients. Expressions are defined for the velocity and temperature profiles and the roughness length after a step change in surface roughness, which causes the disturbance. A pertrurbation could also arise from a heat flux input of a pressure gradient. The effects of the shape of the perturbing step and the presence of several disturbing edges are explored. Finally, it is shown that closure forms and constants for self-preserving flows are worthy of further development because of their demonstrable abilities to describe simple perturbed flows.

Smits, A. J.↗

Ground Based Program for the Physical Analysis of Macromolecular Crystal Growth

During the past year we have focused on application of in situ Atomic Force Microscopy (AFM) for studies of the growth mechanisms and kinetics of crystallization for different macromolecular systems. Mechanisms of macrostep formation and their decay, which are important in understanding of defect formation, were studied on the surfaces of thaumatin, catalase, canavalin and lysozyme crystals. Experiments revealed that step bunching on crystalline surfaces occurred either due to two- or three-dimensional nucleation on the terraces of vicinal slopes or as a result of uneven step generation by complex dislocation sources. No step bunching arising from interaction of individual steps in the course of the experiment was observed. The molecular structure of the growth steps for thaumatin and lipase crystals were deduced. It was further shown that growth step advance occurs by incorporation of single protein molecules. In singular directions growth steps move by one-dimensional nucleation on step edges followed by lateral growth. One-dimensional nuclei have different sizes, less then a single unit cell, varying for different directions of step movement. There is no roughness due to thermal fluctuations, and each protein molecule which incorporated into the step remained. Growth kinetics for catalase crystals was investigated over wide supersaturation ranges. Strong directional kinetic anisotropy in the tangential step growth rates in different directions was seen. The influence of impurities on growth kinetics and cessation of macromolecular crystals was studied. Thus, for catalase, in addition to pronounced impurity effects on the kinetics of crystallization, we were also able to directly observe adsorption of some impurities. At low supersaturation we repeatedly observed filaments which formed from impurity molecules sedimenting on the surfaces. Similar filaments were observed on the surfaces of thaumatin, canavalin and STMV crystals as well, but the frequency was low compared with catalase crystallization. Cessation of growth of xylanase and lysozyme crystals was also observed and appeared to be a consequence of the formation of dense impurity adsorption layers. Attachment: "An in situ AFM investigation of catalase crystallization", "Atomic force microscopy studies of living cells: visualization of motility, division, aggregation, transformation, and apoptosis", AFM studies on mechanisms of nucleation and growth of macromolecular crystals", and "In situ atomic force microscopy studies of surface morphology, growth kinetics, defect structure and dissolution in macromolecular crystallization".

Malkin, Alexander J.↗

Theoretical study of the ammonia nitridation rate on an Fe (100) surface: A combined density functional theory and kinetic Monte Carlo study

Ammonia (NH{sub 3}) nitridation on an Fe surface was studied by combining density functional theory (DFT) and kinetic Monte Carlo (kMC) calculations. A DFT calculation was performed to obtain the energy barriers (E{sub b}) of the relevant elementary processes. The full mechanism of the exact reaction path was divided into five steps (adsorption, dissociation, surface migration, penetration, and diffusion) on an Fe (100) surface pre-covered with nitrogen. The energy barrier (E{sub b}) depended on the N surface coverage. The DFT results were subsequently employed as a database for the kMC simulations. We then evaluated the NH{sub 3} nitridation rate on the N pre-covered Fe surface. To determine the conditions necessary for a rapid NH{sub 3} nitridation rate, the eight reaction events were considered in the kMC simulations: adsorption, desorption, dissociation, reverse dissociation, surface migration, penetration, reverse penetration, and diffusion. This study provides a real-time-scale simulation of NH{sub 3} nitridation influenced by nitrogen surface coverage that allowed us to theoretically determine a nitrogen coverage (0.56 ML) suitable for rapid NH{sub 3} nitridation. In this way, we were able to reveal the coverage dependence of the nitridation reaction using the combined DFT and kMC simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cytosolic lipid droplets as engineered organelles for production and accumulation of terpenoid biomaterials in leaves

Cytosolic lipid droplets are endoplasmic reticulum-derived organelles typically found in seeds as reservoirs for physiological energy and carbon to fuel germination. In this work, we report synthetic biology approaches to co-produce high-value sesqui- or diterpenoids together with lipid droplets in plant leaves. The formation of cytosolic lipid droplets is enhanced in the transient Nicotiana benthamiana system through ectopic production of WRINKLED1, a key regulator of plastid fatty acid biosynthesis, and a microalgal lipid droplet surface protein. Engineering of the pathways providing the universal C5-building blocks for terpenoids and installation of terpenoid biosynthetic pathways through direction of the enzymes to native and non-native compartments boost the production of target terpenoids. We demonstrate that anchoring of distinct biosynthetic steps onto the surface of lipid droplets leads to efficient production of terpenoid scaffolds and functionalized terpenoids. The co-produced lipid droplets “trap” the terpenoids in the cells.

59 BASIC BIOLOGICAL SCIENCES↗