Search NASA⌕ Search

SEARCH · Search NASA

Results for “Scanning Electron Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Vanadium-enhanced Na 2 FePO 4 F cathodes for high-performance sodium-ion batteries

Sodium fluorophosphate Na 2 FePO 4 F holds great potential for sodium-ion batteries due to its high theoretical capacity, excellent structural stability, abundant resources, and affordability. However, its poor electronic and ionic conductivities limit its practical applications. Therefore, ion doping and carbon coating have been employed as synergistic strategies in this study to overcome these limitations. A one-step, energy-efficient solid-state method using sucrose as a carbon coating source was used to synthesize Na 2 FePO 4 F/C (NFPF/C) and its doped variant, Na 2 Fe 0.85 V 0.1 PO 4 F/C (NFVPF/C). 23 Na-MAS-NMR spectra confirm the existence of two distinct sites for sodium (Na1/Na2). The ex-situ 23 Na-MAS-NMR performed at different states-of-charge reveals the activity of only one sodium. The scanning electron microscopy findings reveal a reduction in the particle size with V-introduction, enhancing the energetic performances. NFVPF/C delivers higher specific capacity of 122 mAh g −1 compared to 116 mAh g −1 for NFPF/C at 0.1C. It also demonstrates improved cycling stability, retaining 81 % of its initial capacity after 120 cycles, in contrast to 46 % for the pristine material. The doped phase outperforms the pristine at higher current rates, delivering specific capacities of 81 and 55 mAh g −1 at 2C and 3C, respectively, compared to 35 and 17 mAh g −1 for NFPF/C.

25 ENERGY STORAGE↗
DOE OSTI2026

Unravelling fast-charging degradation in NMC/Gr pouch cells: Lithium plating and SEI properties

As fast-charging technology expands across the electric vehicle and emerging energy-storage applications, understanding its impact on battery performance and longevity is critical. In this study, 1.8 Ah LiNi 0.6 Mn 0.2 Co 0.2 O 2 /graphite pouch cells were charged at various charging rates (0.5C, 2C, 4C, and 6C) to investigate the degradation mechanisms. Our results showed that well-designed NMC/Gr pouch cells could reach over 1000 cycles with a 2C charging rate, while only reaching around 500 cycles with 4C and 6C charging rates. Fast-charging effects on NMC and graphite electrodes were obtained through a series of post-mortem characterizations, including electrochemical impedance spectroscopy (EIS), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS). Although higher charging rates cause pulverization of NMC secondary particles, the dominant degradation mechanism driving the fading of fast-charging-related performance lies in the graphite anode, where lithium plating and LiF-rich solid electrolyte interphase (SEI) formation result in Li inventory loss and impedance growth. The postmortem results suggest that the formation of a LiF-rich SEI, which exacerbates anode impedance and some irreversible Li + ion loss, is likely driven by the substantial decomposition of PF 6 − during fast charging, an effect often overlooked in smaller laboratory-scale studies.

Luo, Mei [Argonne National Laboratory (ANL), Argon↗
DOE OSTI2024

Segmentation and Classification of Fission as Pores in Reactor Irradiated Annular U–10Zr Metallic Fuel Using Machine Learning Models

Metallic fuels, particularly U—10Zr, are promising candidates for next-generation sodium-cooled fast reactors. Irradiation of nuclear fuels in reactors can lead to the formation of solid and gas fission product which subsequently forms microstructural pores, deteriorating fuel performance. Due to the massive amount of pores and complex phases formed, a quantitative description of fission gas pores is not yet available, preventing the development of microstructure-informed fuel performance modeling for fuel qualification. This paper applied a pre-trained deep learning model to ~10,260 high magnification scanning electron microscopy images. This method increased the accuracy of fission gas pore segmentation and allows statistical features to be extracted which cannot be achieved manually. A pre-trained decision tree model worked on the segemenation results and further classified the pores into different categories to produce a correlation between the pores, movement of lanthanides, and temperature gradient during irradiation. Finally, this paper emphasizes the potentials of machine learning models to accelerate fuel research, development, and qualification for advanced reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Nondestructive ultrasonic characterization of a triple-weld-bead wire arc additively manufactured ER70S-6 S-curved wall

Understanding build-scale microstructural variation in wire arc additive manufacturing (WAAM) of low-carbon steels is essential for ensuring consistent structure–property relationships throughout large components. Conventional destructive characterization techniques, such as scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), are time-intensive and limited to localized regions, making comprehensive evaluation of large WAAM structures challenging. In this study, a nondestructive ultrasonic approach was employed to characterize a 252 mm tall ER70S-6 S-curved WAAM wall produced using a triple-bead deposition strategy. Optical and SEM analysis revealed a repeating dual-region microstructure consisting of uniform polygonal ferrite at melt pool centers and heterogeneous ferrite with coarse and fine grains near melt pool boundaries, attributed to cyclic thermal conditions. Longitudinal ultrasonic backscatter imaging was used to evaluate the continuity of this periodicity along the full build height. The ultrasonic response exhibited a consistent repeating pattern that correlated with the observed layer-wise microstructural variation. X-ray computed tomography confirmed the absence of detectable porosity, indicating that ultrasonic contrast is primarily governed by grain morphology. Overall, the results indicate that longitudinal backscatter ultrasound is a promising nondestructive characterization technique for validating microstructural variations along the s-curved WAAM wall, with significant potential for microstructure optimization and process control.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Mapping the Microhardness of Al Matrix in U-7Mo/Al Dispersion Fuels at Medium and High Burn-up by in situ Nanoindentation

The mechanical degradation of the Al matrix in U-7Mo dispersion fuels was detected after irradiation in previous studies, but more details of the degradation mechanism are not clear yet to clarify the root cause. In this study, microhardness mapping in fresh and irradiated U-7Mo dispersion fuels coated with ZrN, with burn-up of 3.35 × 10 21 and 6.28 × 10 21 f/cm 3 , are measured to reveal the hardening of the Al matrix as a function of distance to fuel particles. Micro cubes were pulled by plasma focused ion beam scanning electron microscopy and tested by in situ nanoindenter with Berkovitch tip. Size effects are measured in medium and high burn-up samples. The higher burn-up specimen exhibits a more pronounced size effect when indent load is lower than 20 mN. Size effect correction models are also calculated by plots fitting, which predicts the true microhardness without size effect. Results shows that the hardness of the Al matrix near the ZrN coating has the highest value, then decreases moving away from the coating and become stable when the distance reaches ∼10 µm. The hardness starts increasing again getting closer to the next fuel particle, which makes the hardness distribution between two fuel particles to be “U” shape.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Novel white light-emitting CdSe:Mn 2+ synthesized by photo-assisted chemical bath deposition

Nowadays, white light-emitting materials have attracted extensive research due to their potential applications in lighting devices and displaying images. Several semiconductor nanoparticles have been explored to achieve efficient white light emission. In this work, we report on novel white light-emitting CdSe:Mn 2+ thin films synthesized by photo-assisted chemical bath deposition. The effect of varying the Mn 2+ ion concentrations on the thin film structure, morphology, and optical properties was investigated. X-ray powder diffraction results indicated that all the films annealed at 250 degrees C possessed a cubic structure, with crystallite sizes in the range of 1-130 nm. Scanning electron microscopy demonstrated spherical nanoparticles with no significant changes with varying Mn 2+ doping concentrations. Energy dispersive X-ray spectroscopy confirmed the presence of the anticipated elements. The atomic force microscope revealed that the surface roughness has decreased with an increase in Mn 2+ ion concentrations but decreased for 0.7 %Mn 2+ . The UV-Vis absorption spectra showed absorption edges around 600-650 nm. Photoluminescence emission spectra excited at 3.8 eV (325 nm) showed emission bands at around 1.75 eV (709 nm), and 1.88 eV (659 nm), which were attributed to the band-to-band emission, and 4 T 1 ( 4 G)-> 6 A 1 ( 6 S) transitions of Mn 2+ ions, respectively, while emission bands at 2.35 eV (528 nm), and prominent at 3.17 eV (391 nm) were due to the glass substrate. The temperature-dependent luminescence showed a decrease in relative emission intensity with the increase in the operating temperature. The chromaticity colour coordinates showed white light-emitting thin films. These present findings open a new door to developing white light using CdSe thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Combining four-point bending and corrosion to map stress-dependent corrosion susceptibility of 316H stainless steel in FLiNaK

Understanding the effect of stress on the corrosion of steels in molten salts is important for material screening and safety assessment of molten salt reactors. We present a method that combines four-point bending with corrosion testing, enabling the mapping of corrosion susceptibility as a function of local stress from a single specimen. Guided by finite element analysis, a four-point bending setup was used to bend a 316H stainless-steel bar under controlled elastic stress during a 100-hour exposure in FLiNaK at 700 °C. Post-exposure characterization using scanning electron microscopy and energy-dispersive X-ray spectroscopy revealed a pronounced correlation between stress and corrosion. Regions under tensile stress exhibited significantly deeper attack depths and greater chromium depletion along grain boundaries, whereas compressive zones showed shallower corrosion cracks. The stress effect is attributed to stress concentration under tensile loading, which promotes chromium dissolution and crack propagation. This technique can be readily applied to other structural alloys, enabling quantitative measurement of corrosion susceptibility as a function of local stress.

316H↗
DOE OSTI2025

Post-build stress-relief optimization for laser powder bed fusion 316H stainless steel

Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.

316 stainless steel↗
DOE OSTI2025

Deciphering volume changes in Li-S solid-state battery components during cycling: Implication for advanced battery design

Here, in this work, we developed custom fixtures to investigate the mechanical and electrochemical behavior of all-solid-state lithium batteries during cycling under constant pressure and constant volume conditions. We successfully monitored vertical displacements during constant pressure cycling and pressure variations during constant volume cycling, allowing us decouple volume changes in the sulfur, Li 2 S cathodes, LixIn anode, and solid-state electrolyte. Scanning electron microscopy and electrochemical impedance spectroscopy confirmed that two structural changes occur during ASSLB cycling: (1) irreversible fractures in the active material particles, and (2) void formation within the electrode matrix. While the fractures in primary particles are permanent, void formation can be mitigated through stack pressure, which promotes particle rearrangement in the electrode matrix. Our findings emphasize the importance of stack pressure in maintaining the microscale integrity of all-solid-state lithium batteries, preventing void formation and enhance battery performance and durability.

Cell Design↗
DOE OSTI2025

Tailoring copper current collector roughness and crystallographic orientation to improve lithium plating

Secondary lithium metal batteries are of great interest due to a high theoretical energy density, but rechargeability is limited by the formation of lithium dendrites that lead to internal short circuits and catastrophic cell failure. Mitigating dendrites through uniform current distribution at the current collector is a promising solution to enabling long cycle life of lithium metal electrodes. Here, the impact of copper crystal orientation and roughness on electrochemically deposited lithium morphology is studied. For 50 cycles, the capacity retention from greatest to least followed polycrystalline copper 95 ± 1 % (MC-PC) ≥ 94.55 ± 0.01 % Cu (110) > 93.0 ± 0.4 % Cu(111) > 75.8 ± 0.1 % Cu(100). Cu(100) performed the worst in all cases with shorts occurring frequently before reaching 50 cycles. Cryo-scanning electron microscopy images showed that after 50 cycles, MC-PC Cu had the best lithium morphology, but at early cycles, Cu(111) formed the densest lithium layer. MC-PC Cu had the most uniform lithium nucleation which may have been caused by increased roughness relative to the single crystal samples. When polycrystalline Cu (F-PC) roughness was systematically controlled, the cumulative Coulombic efficiency increased from about 0.3–0.5 with increasing roughness from an Ra of about 10–40 nm. Lastly, plating rates were studied. Slower rates of 0.25 mA/cm 2 exhibited denser lithium morphology in all cases as compared to 0.5 and 1.0 mA/cm 2 , but the relative porosity of Li deposited on the different current collectors depended on the rate applied.

Copper↗
DOE OSTI2026

Combustion-assisted ink-jet printing of nuclear targets

Advances in target fabrication are critical to high-precision measurements in nuclear physics. This work details the preparation of patterned CeO 2 and ThO 2 architectures and thin-film targets via ink-jet deposition of combustible solutions. The produced targets were characterized by scanning electron microscopy (SEM), and by alpha-particle spectroscopy for radioactive targets to determine densities. Ink jet printing of the targets, used both ethanol and 2-methoxyethanol as solvents, with cerium or thorium nitrate as the oxidizer and acetylacetone as the fuel. Additionally, we found that the distance between each droplet dispersion (step size) played the most significant role in determining the final pattern uniformity and thickness. A 50 μm step size leads to relatively thick targets with a density of 350 μg/cm 2 . Significant overlap in droplet sizes leads to a heterogeneous target with an undesirable cracked surface structure. In contrast, 150 μm spacing yields thinner (20 μg/cm 2 ) patterned structures with excellent surface coverage. This method of Ink-jet printing provides a straightforward, scalable, and high-efficiency pathway to prepare custom made, high-quality targets for nuclear physics experiments.

CeO2↗
DOE OSTI2024

Spark plasma sintering of fuel meats for U 3 O 8 based dispersion fuels

Research and test reactors often use dispersion-type fuel due to its increased thermal conductivity and burn-up capabilities compared to conventional fuel. Al-U 3 O 8 (aluminumtriuranium octaoxide) dispersion fuels have several advantages over their competitors, such as higher service temperature and better stability of oxygen stoichiometry. However, the two-step fabrication of dispersion fuel causes undesirable porosity in cold-pressed fuel meats that is preserved in co-extruded fuel plates. To combat this, spark plasma sintering (SPS) was used for the fabrication of Al-15, 20, and 30 vol% U 3 O 8 and 8 and 12 vol% Mo-U 3 O 8 fuel meats for the Al-U 3 O 8 time. The in situ SPS data was used to construct and validate Master Sintering Curves (MSCs) with accuracies in Al fuels at 0.02 g/cm 3 , and Mo fuels at 0.07 and 0.17 g/cm 3 . The as-sintered fuel meats were characterised using x-ray diffraction (XRD) and scanning electron microscopy (SEM) to understand chemical and physical changes following the SPS process. The pellets exhibited very high relative densities, the U 3 O 8 was observed to undergo reduction to UO 2 .

Aluminium↗
DOE OSTI2025

Design of novel refractory equiatomic multi-principal elemental alloys based on Mo-Nb-Ti system for Gen IV reactor applications

Excellent irradiation damage resistance demonstrated by multi-principal elemental alloys (MPEAs) has sparked significant interest among researchers, prompting exploration into their vast compositional space, to validate their suitability for nuclear applications. A combined approach of thermodynamic and empirical parameters calculations alongside CALPHAD (CALculation of PHAse Diagrams) for phase formation predictions enable high-throughput material selection for sophisticated applications like nuclear, overcoming laborious and time-consuming experiments. Key thermodynamic and empirical parameters for eight novel equiatomic MPEAs, based on seven low thermal neutron cross section refractory elements, for predicting phase formation were calculated, and equilibrium and non-equilibrium simulations in CALPHAD were employed to comprehensively model the systems. Pseudo binary phase diagram simulations showed that Zr, V or equiatomic CrV additions to the base MoNbTi alloy (MoNbTi-Zr, MoNbTi-V and MoNbTi-CrV alloys) favor the formation of isomorphous body-centered cubic (BCC) phase at high temperatures, while Cr, Al, equiatomic ZrV, or equiatomic CrAl additions (MoNbTi-Cr, MoNbTi-Al, MoNbTi-ZrV or MoNbTi-CrAl alloys) limit the solubility of them. Equilibrium CALPHAD simulations at 750 oC were consistent with XRD results on MoNbTi, MoNbTiZr and MoNbTiCr alloys, and partially for others. Notably, elemental segregation observed in the backscattered electron (BSE) scanning electron microscopy (SEM) images of the alloys was accurately simulated through non-equilibrium Scheil solidification calculations in CALPHAD, further verified by experiments. The precipitation of TiCr2 Laves phase in Cr containing MoNbTiCr and MoNbTiCrAl was accurately predicted while discrepancies were noted in MoNbTiCrV. The equilibrium simulations also provided insights into phase compositions at specific temperatures offering a pathway for tailoring the desired microstructure and properties of these systems. Empirical parameters calculations successfully predicted random solid solution in the base MoNbTi alloy, and with an exception in MoNbTiV and MoNbTiAl, predicted intermetallic precipitation in the rest, especially, Laves phase precipitation in Cr containing alloys.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

ROADRUNNER uranium nitride MiniFuel: Experimental design, fabrication and pre-irradiation baseline characterization for accelerated burnup testing

Uranium nitride (UN) is a promising fuel candidate for advanced reactor systems owing to its high uranium density and thermal conductivity; however, its qualification remains constrained by the scarcity of well-controlled irradiation performance data. Here, to address this limitation, the ROADRUNNER (Research On ADvancing the peRformance of UraNium Nitrides in Extreme enviRonments) campaign employs the MiniFuel platform in the High Flux Isotope Reactor (HFIR) to enable accelerated burnup irradiation testing under tightly controlled and largely isothermal conditions. This paper presents the experimental design, fuel fabrication, and pre-irradiation baseline characterization of the ROADRUNNER UN MiniFuel campaign. Thirty-six UN minidisc specimens were fabricated with systematically varied as-fabricated density (86–96% of theoretical density), carbon impurity content (961–5240 ppm), oxygen content (≤ ∼2000 ppm), and grain size (2.5–24 μm). The irradiation matrix spans nominal fuel temperatures of 873 K, 1173 K, and 1473 K and target burnups of 3.75%, 6.0%, and 7.5% fissions per initial metal atom (FIMA). Neutronic and thermal analyses were performed to define specimen-specific burnup accumulation and temperature histories, establishing the boundary conditions for subsequent in-pile behavior. Comprehensive pre-irradiation characterization—including dimensional metrology, density verification, impurity analysis, X-ray diffraction, Raman spectroscopy, scanning electron microscopy, X-ray computed tomography, and confocal profilometry—provides a detailed baseline for post-irradiation examination. Pre-irradiation data were further used to generate predictive estimates of fission gas release and swelling using existing empirical correlations. This quantitative comparison reveals substantial inter-model divergence at intermediate and elevated temperatures that exceeds propagated input uncertainties, highlighting structural gaps in the historical irradiation database. The ROADRUNNER irradiation campaign is currently underway in HFIR, with initial firs cycle completed in late 2025 and remaining targets scheduled through 2027. The experimental design and baseline dataset presented here establish the framework needed to interpret forthcoming post-irradiation measurements and to provide discriminating data for the validation and refinement of physics-based UN fuel performance models.

Lopes, Denise Adorno [Oak Ridge National Laborator↗
DOE OSTI2025

Effect of 3D-printed surface textures on wear mechanism in 3-body abrasion of soil

This study systematically investigates the enhancement of wear resistance in 3D printed surface textures through both experimental and theoretical approaches. Three distinct surface morphologies (Smooth Surface, Surface with uniformly distributed Pits, and Surface with uniformly distributed Bumps) were fabricated using High-Impact Polystyrene, where the meso-scale textures were precisely controlled through the 3D printing process. Wear behavior was evaluated using a 3-body wear tester in an abrasive particle environment, analyzing the influence of surface textures under various operating conditions. Systematic wear tests revealed that optimally designed surface textures achieved a remarkable 77 % reduction in wear compared to the worst-performing sample. The wear mechanisms were comprehensively characterized through weight loss measurements, Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS) analyses, elucidating the surface morphology changes and their interaction with wear particles. Notably, the study identified how the geometric characteristics of surface textures influence the movement of wear particles and the distribution of contact stresses. Discrete element method simulations corroborated the experimental findings, providing theoretical validation for the enhanced wear resistance of the optimal structure. The high correlation between simulated wear patterns and experimental results validates the reliability of the proposed design methodology. In conclusion, these results demonstrate that 3D printed surface texturing offers a cost-effective and scalable approach to significantly improve wear resistance in engineering applications, presenting a practical alternative to conventional, high-cost surface engineering methods.

3-body abrasion↗
DOE OSTI2026

Conversion of real-world aluminum scrap streams into high-performance Al–Mg–Si–Cu automotive alloys using shear assisted processing and extrusion

The conversion of post-consumer aluminum (Al) scrap into usable Al alloys without adding primary Al is challenging because of excess impurities. In this work, >99% post-consumer Twitch, used beverage cans (UBCs), and remelt scrap ingots (RSIs) were used as feedstock materials. As-cast and solution heat-treated feedstock billets were extruded using Shear Assisted Processing and Extrusion (ShAPE) at ~510°C, followed by press quenching. To explore the development of the microstructure, texture, and underlying mechanisms and how they contribute to the overall strengthening in as-extruded and artificially aged samples, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) were used to collect microstructure and texture data. The enhanced strength and ductility were corroborated with the microstructural features and crystallographic texture. Simple shear $\textrm{A}/\bar{\textrm{A}}$, $\textrm{A}_1^*/\textrm{A} _2^*$ texture components along with weak $\textrm{C}$ and $\textrm{B}/\bar{\textrm{B}}$ texture components were formed during extrusion; the texture was strengthened after heat treatment. The refined second-phase particles helped to retain the deformed microstructure and texture. The contributions of dislocation and precipitate strengthening were maximized when billets were solution-heat-treated prior to extrusion. This is attributed to the formation of effective supersaturated solid solutions during the ShAPE process, which precipitate out during the peak age treatment. Overall, the highest yield strength of 305 MPa, ultimate tensile strength of 350 MPa, and elongation of 12% were achieved in artificially aged samples, which are comparable to those of Al 6082-T6.

Al alloy↗
DOE OSTI2024

Computational thermodynamics-guided alloy design and phase stability in CoCrFeMnNi-based medium-and high-entropy alloys: An experimental-theoretical study

A computational thermodynamics approach has been employed to design CoCrFeMnNi-based medium- and high-entropy alloys (M/HEAs) with systematically varied compositions (Co(( 80-X )/ 2 )Cr(( 80-X )/ 2 )Fe X Mn 10 Ni 10 with x = 30, 40, and 50 at.%) and phase stability. Since the formation of sigma phase, usually brittle and undesirable, is a common concern, when this class of alloys is subjected to elevated temperatures (600–1000 °C), predicting its formation becomes essential. Thus, its formation and the phase equilibria were studied using the CALPHAD method, and two empirical methods, namely, valence electron concentration (VEC) and paired sigma-forming element (PSFE). Isothermal aging treatments at 900–1100 °C for 20 h were performed, since CALPHAD and VEC/PSFE predictions diverged. Both prediction methods were compared with experimental characterization by a combination of scanning electron microscopy and high-energy synchrotron X-ray diffraction. In conclusion, the predictions from the VEC/PSFE and CALPHAD calculations (depending on the database used) were shown to be quite accurate.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Corrosion protection of mild steel by superhydrophobic magnetite coating

Corrosion-resistant hydrophobic magnetite coatings on mild steel surfaces were developed by immersion method. The effect of steel surface roughness (R a ) on its hydrophobicity was systematically studied using contact angle measurement (CAM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The corrosion resistance of hydrophobic magnetite coatings was evaluated using a potentiodynamic polarization test. The durability of the coatings was assessed in air, tap water, and 3.5 wt% NaCl environments. Hydrophobic magnetite coating with a water contact angle of 146-152° showed excellent resistance to corrosion, longevity in atmospheric air, and significant self-cleaning properties. The primary focus of this study was to develop a quick and simple immersion technique to create hydrophobic surfaces on mild steel. Finally, results suggest that surface roughness plays a significant role in surface hydrophobicity, and enhancing the hydrophobicity of mild steel improves its corrosion resistance.

36 MATERIALS SCIENCE↗