Search NASA⌕ Search

SEARCH · Search NASA

Results for “carbon neutrality”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Annealing of radiation damage in low resistivity silicon solar cells

The reduction of the temperatures required to restore cell performance after irradiation was investigated with emphasis on the annealing characteristics of two groups of cells containing different amounts of oxygen and carbon. Examination of defect behavior in irradiated boron doped silicon leads to the tentative conclusion that further reduction in annealing temperature could be achieved by decreasing the carbon concentration and either neutralizing the divacancy and/or minimizing its formation as a result of irradiation. A significant reduction in the temperature required to remove radiation induced degradation in 0.1 ohm centimeter silicon solar cells was achieved.

Weinberg, I.↗
NASA NTRS1985

Ultraviolet spectra and chromospheres of R stars

Long-wavelength IUE spectra of 13 normal R stars and two hydrogen-deficient R0 supergiants were obtained. Early R stars are noted to have line spectra and levels of flux in the ultraviolet characteristic of G5-K2 III stars, whereas late R stars were observed to have colors and line spectra similar to late K and M stars, but with greatly enhanced strength of low-lying multiplets of neutral metals. Hydrogen-deficient carbon stars show readily apparent differences from the normal early R stars, reflecting their luminosity and somewhat higher temperatures. The lines of neutral metals in these stars are weakened, while those of ionized metals are strengthened.

Eaton, J. A.↗
DOE OSTI2021

Graphitized Biocarbon Derived from Hydrothermally Liquefied Low-Ash Corn Stover

Graphitized biocarbon can be utilized for energy storage applications such as supercapacitors. The scientific community have geared their attention to obtain such value-added product from abundantly available and low-cost biomass feedstock agricultural residues such as corn stover. Lignocellulosic components embedded within the cell wall of biomass substrates can provide a fine template for enhanced ion storage, transport, and rate capabilities, desirable for electrochemical storage. Presented is the utilization of homogenized low ash content corn stover milled and sieved to desired specifications, which underwent hydrothermal liquefaction in the presence of Ni-based catalytic salts at 275 o C. The hydrochar obtained by solid residue extracted from the reaction slurry was washed to acid neutral and subjected to catalytic activation using ZnCl 2 , followed by thermal annealing at 400 o C for morphological and pore size enhancement of the resulting biochar. Carbonization was performed on acid neutralized hydrochar at 850 °C to further enhance pore structures and increase graphitization for improved conductivity. Catalytic materials exhibited a specific capacitance of 316 F g -1 and held a 100% retention beyond 10,000 cycles. BET, Raman, XRD, cyclic voltammetry, chronopotentiometry, and EIS are discussed herein.

Biomass↗
DOE OSTI2026

Development and application of a low-noise, high-speed optical detector module for carbon density fluctuation measurements on Wendelstein 7-X

A low-noise, high-speed optical detector module is characterized and successfully commissioned for the measurement of high-frequency, low-intensity beam emission on Wendelstein 7-X (W7-X). An ultra-narrow bandpass optical filter is employed to selectively transmit the desired emission line while suppressing broadband plasma background emissions. Carbon density fluctuations are investigated by observing the carbon C-VI emission line (n = 8 → 7, λ ∼ 529 nm), arising from charge exchange (CX) between the neutral beam atoms and the intrinsic carbon population. Here, we present the characterization of the optical detector module and experimental measurements of carbon density fluctuations using available fibers on W7-X. The initial performance of the detector is presented in both active and passive CX measurements of intrinsic carbon density fluctuations. The low frequency dynamics of fluctuation is observed in response to the neutral beam and the pellet injection, demonstrating that the optical detector module is capable of providing a sufficient signal level with an adequate signal-to-noise ratio. In the upcoming OP2.4 campaign, this optical detector module will be adapted for use in a beam emission spectroscopy system by replacing the optical bandpass filter with one centered at 654 nm (90% transmission: 653–655.3 nm), which facilitates two-dimensional measurements of ion gyro-scale turbulence on W7-X.

Charge exchange recombination spectroscopy↗
NASA NTRS1994

Far-infrared emission line spectroscopy of planetary nebulae from the KAO

The main focus of the overall project was to study the properties of planetary nebulae using far-infrared emission lines. The observations were conducted with the 'cooled grating spectrometer' or CGS, a moderate-resolution echelle spectrometer designed and built at the Ames Research Center. During the first few years of the program, the emphasis was on emission lines of doubly-ionized oxygen and nitrogen ((O III) 52 and 88 microns, (N III) 57 microns), which arise in the ionized regions of the nebulae. Starting around 1989, our emphasis shifted to observing fine-structure lines of neutral oxygen and singly-ionized carbon ((O I) 63 and 145 microns, (C II) 157 microns), which arise from predominantly neutral material outside the ionized regions. This program was typically assigned one or two observing flights per year. Because these studies required obtaining a substantial sample of objects in order to reach meaningful conclusions, publication of comprehensive papers summarizing all of the results is still pending. However, numerous interim reports based on the airborne results as well as on closely-related supporting observations have been published during the grant period. The bibliographic information for these reports is given in the publications section. An overall summary of the planetary nebula results was presented at the Airborne Astronomy Symposium (20th Anniversary of the KAO) on 8 July 1994; reprints will be provided when available. In parallel with the planetary nebula study, we also observed the (O III) and (N III) lines in several H II regions, and attempted (unsuccessfully) to detect these lines in several old nova remnants and the supernova remnant Cassiopeia A.

Dinerstein, Harriet L.↗
DOE OSTI2023

Isotope dependence of transport in ST40 hot ion mode plasmas

The ST40 compact, high-field spherical tokamak, operating at 2.1 T and with 1.8 MW of neutral beam heating, achieved central carbon impurity ion temperatures in excess of 10 keV, surpassing their business milestone of 100 M °C (8.6 keV). The high temperature discharges were in the hot ion mode, with $T_i \gg T_e$, and they were achieved in both hydrogen and deuterium plasmas with deuterium neutral beam injection. In order to achieve the high temperature scenarios, careful wall conditioning and scenario optimization was carried out in $H^0 \rightarrow H^+$, $D^0 \rightarrow H^+$, and finally in $D^0 \rightarrow D^+$ plasmas. The TRANSP transport code was employed to study the dependence of confinement and transport on isotopic mass, and the conditions that led to the high measured central ion temperatures in the $D^0 \rightarrow H^+$ and $D^0 \rightarrow D^+$ plasmas. The kinetic profiles input into TRANSP were inferred from line-of-sight and limited radial measurements as well as consistency with a number of other experimental constraints. The TRANSP results first showed that the main species central ion temperature was only 0.5–1 keV lower than the measured carbon impurity temperature, and thus in the high performance plasmas also surpassed the 100 M °C level. TRANSP also showed that while the electron thermal conduction loss was dominant, reductions in central ion transport, and an effective decoupling of the ions from the electrons, led to an increase in central ion temperatures with increasing plasma mass. In fact, the associated confinement times exhibited a strong dependence on the isotopic mass of the thermal plasma. These preliminary results are foundations for dedicated experiments with full kinetic profile measurements on ST40 in the next run campaign.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2018

Simulating Forest Dynamics of Lowland Rainforests in Eastern Madagascar

Ecological modeling and forecasting are essential tools for the understanding of complex vegetation dynamics. The parametric demands of some of these models are often lacking or scant for threatened ecosystems, particularly in diverse tropical ecosystems. One such ecosystem and also one of the world's biodiversity hotspots, Madagascar's lowland rainforests, have disappeared at an alarming rate. The processes that drive tree species growth and distribution remain as poorly understood as the species themselves. We investigated the application of the process-based individual-based FORMIND model to successfully simulate a Madagascar lowland rainforest using previously collected multi-year forest inventory plot data. We inspected the model's ability to characterize growth and species abundance distributions over the study site, and then validated the model with an independently collected forest-inventory dataset from another lowland rainforest in eastern Madagascar. Following a comparative analysis using inventory data from the two study sites, we found that FORMIND accurately captures the structure and biomass of the study forest, with r(squared) values of 0.976, 0.895, and 0.995 for 1:1 lines comparing observed and simulated values across all plant functional types for aboveground biomass (tonnes/ha), stem numbers, and basal area (m(squared)/ha), respectively. Further, in validation with a second study forest site, FORMIND also compared well, only slightly over-estimating shade-intermediate species as compared to the study site, and slightly under-representing shade-tolerant species in percentage of total aboveground biomass. As an important application of the FORMIND model, we measured the net ecosystem exchange (NEE, in tons of carbon per hectare per year) for 50 ha of simulated forest over a 1000-year run from bare ground. We found that NEE values ranged between 1 and -1 t Cha(exp -1)year(exp -1), consequently the study forest can be considered as a net neutral or a very slight carbon sink ecosystem, after the initial 130 years of growth. Our study found that FORMIND represents a valuable tool toward simulating forest dynamics in the immensely diverse Madagascar rainforests.

Forest Productivity↗
DOE OSTI2024

Effects of the U.S. inflation reduction act on SMR economics

The U.S. Inflation Reduction Act (IRA) of 2022 provides a wide array of tax credits and other incentives for low-carbon energy. The technology-neutral clean generation production tax credit (PTC) (Section 45Y of the U.S. Internal Revenue Code) and the technology-neutral investment tax credit (ITC) (Section 48E) lower the net cost of new electricity generation projects with zero or negative greenhouse gas emission rates. We evaluate the impact of the IRA legislation—specifically the PTC and ITC—on the cost-competitiveness of small modular reactors (SMRs). We use the Argonne Low-carbon Energy Analysis Framework (A-LEAF) model to calculate the capacity factor of an SMR with a range of hypothetical variable operating and maintenance (O&M) costs in the Electric Reliability Council of Texas (ERCOT) electricity market. We selected ERCOT for market modeling because of its competitive structure, available data, and extensive use in prior literature. We use a discounted cash flow model to calculate the SMR’s net present value based on the market prices and capacity factors from A-LEAF, hypothetical ranges of capital and variable O&M costs, and other input parameters, with or without the IRA tax credits. We determine the SMR owner’s optimal choice of PTC or ITC for the hypothetical ranges of capital and variable O&M costs. We also evaluate potential shifts in the SMR owner’s optimal choice of PTC or ITC based on historical patterns of nuclear capital cost overruns in the United States. We also assess the sensitivity of our results to longer PTC period and electricity prices from the New England market, which tend to be higher than electricity prices in ERCOT. We find that even with the IRA tax credits, only SMRs with low capital and variable O&M costs would be economically feasible in the low-price ERCOT market scenario modeled. A longer PTC period and higher-price market such as New England, however, would significantly expand the economic feasibility of SMRs in the United States.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

A carbon-efficient bicarbonate electrolyzer

Carbon efficiency is one of the most pressing problems of carbon dioxide electroreduction today. While there have been studies on anion exchange membrane electrolyzers with carbon dioxide (gas) and bipolar membrane electrolyzers with bicarbonate (aqueous) feedstocks, both suffer from low carbon efficiency. In anion exchange membrane electrolyzers, this is due to carbonate anion crossover, whereas in bipolar membrane electrolyzers, the exsolution of carbon dioxide (gas) from the bicarbonate solution is the culprit. Here, we first elucidate the root cause of the low carbon efficiency of liquid bicarbonate electrolyzers with thermodynamic calculations and then achieve carbon-efficient carbon dioxide electroreduction by adopting a near-neutral-pH cation exchange membrane, a glass fiber intermediate layer, and carbon dioxide (gas) partial pressure management. We convert highly concentrated bicarbonate solution to solid formate fuel with a yield (carbon efficiency) of greater than 96%. A device test is demonstrated at 100 mA cm -2 with a full-cell voltage of 3.1 V for over 200 h.

42 ENGINEERING↗
DOE OSTI2021

Zinc–air batteries in neutral/near-neutral electrolytes

The need to fully utilize intermittent renewable energy and have energy security, large-scale batteries are necessary. The aqueous zinc–air battery (ZAB) is a promising potential candidate for its safety, low-cost, and theoretical capacity. This research on ZAB mainly focused on alkaline electrolytes. These are favored for their conductivity, but greatly reduce the stability of the battery by zinc corrosion from the hydrogen evolution reaction (HER), dendrite formation, and carbonate formation. To address these issues, recently neutral and near-neutral electrolytes have been applied to aqueous ZAB to suppress HER, dendrite formation, and minimize carbonate formation. These include the use of chloride-based, potassium nitrate, aqueous organic, solid-state electrolytes supplemented with additives to improve the performance and stability. This field is still young with significant opportunities available for research.

25 ENERGY STORAGE↗
DOE OSTI2022

Pedestal fluctuation measurements with charge exchange imaging at the DIII-D tokamak

A new high radial resolution 2D multichannel Charge eXchange Imaging (CXI) diagnostic is under development for deployment at DIII-D. Here, the diagnostic system will measure low-to-intermediate radial wavenumber carbon density fluctuations by observing the n = 8 – 7 (λ = 529.06 nm) C-VI emission line, resulting from charge exchange collisions between heating neutral beam atoms and the intrinsic carbon ion density. The new CXI diagnostic will provide measurements with ΔR ~ 0.4 cm to access higher k r instabilities (k r < 8 cm –1 ) predicted to arise in the steep-gradient region of the H-mode pedestal. The CXI system will feature 60 fiber bundles in a 12 × 5 arrangement, with each bundle consisting of four 1 mm fibers. A custom optical system has been designed to filter and image incoming signals onto an 8 × 8 avalanche photodiode array. Additionally, a novel electronics suite has been designed and commissioned to amplify and digitize the relatively low-intensity carbon signal at a 2 MHz bandwidth. Forward modeling results of the active C-VI emission suggest sufficient signal to noise ratios to resolve turbulent fluctuations. Prototype measurements demonstrate the ability to perform high frequency pedestal measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

CO 2 electrolysis to multicarbon products in strong acid

Carbon dioxide electroreduction (CO 2 R) is being actively studied as a promising route to convert carbon emissions to valuable chemicals and fuels. However, the fraction of input CO 2 that is productively reduced has typically been very low, <2% for multicarbon products; the balance reacts with hydroxide to form carbonate in both alkaline and neutral reactors. Acidic electrolytes would overcome this limitation, but hydrogen evolution has hitherto dominated under those conditions. We report that concentrating potassium cations in the vicinity of electrochemically active sites accelerates CO 2 activation to enable efficient CO 2 R in acid. We achieve CO 2 R on copper at pH <1 with a single-pass CO 2 utilization of 77%, including a conversion efficiency of 50% toward multicarbon products (ethylene, ethanol, and 1-propanol) at a current density of 1.2 amperes per square centimeter and a full-cell voltage of 4.2 volts.

Huang, Jianan Erick↗
NASA NTRS1990

Reflectance spectra of mafic silicate-opaque assemblages with applications to meteorite spectra

The addition of fine-grained magnetite to mafic silicate spectra can impart not only an overall blue slope, but also lower overall reflectance and band intensities. The reflectance spectra of the CO and CV magnetite-bearing carbonaceous chondrites are noted to exhibit many of these features; the low band depths of these meteorites suggest that an additional dark, neutral phase, such as ordered carbon, is present. Carbon + mafic silicate spectra possess a red overall slope at low amorphous carbon concentrations. The parent bodies of some of the darkest meteorites should exhibit spectral features attributable to mafic silicates.

Cloutis, Edward A.↗
NASA NTRS2021

First Observations from the SPICE EUV Spectrometer on Solar Orbiter

Aims. We present first science observations taken during the commissioning activities of the Spectral Imaging of the Coronal Environment (SPICE) instrument on the ESA/NASA Solar Orbiter mission. SPICE is a high-resolution imaging spectrometer operating at extreme ultraviolet (EUV) wavelengths. In this paper we illustrate the possible types of observations to give prospective users a better understanding of the science capabilities of SPICE. Methods. We have reviewed the data obtained by SPICE between April and June 2020 and selected representative results obtained with different slits and a range of exposure times between 5 s and 180 s. Standard instrumental corrections have been applied to the raw data. Results. The paper discusses the first observations of the Sun on different targets and presents an example of the full spectra from the quiet Sun, identifying over 40 spectral lines from neutral hydrogen and ions of carbon, oxygen, nitrogen, neon, sulphur, magnesium, and iron. These lines cover the temperature range between 20,000 K and 1 million K (10MK in flares), providing slices of the Sun’s atmosphere in narrow temperature intervals. We provide a list of count rates for the 23 brightest spectral lines. We show examples of raster images of the quiet Sun in several strong transition region lines, where we have found unusually bright, compact structures in the quiet Sun network, with extreme intensities up to 25 times greater than the average intensity across the image. The lifetimes of these structures can exceed 2.5 hours. We identify them as a transition region signature of coronal bright points and compare their areas and intensity enhancements. We also show the first above-limb measurements with SPICE above the polar limb in C III,O VI, and Ne VIII lines, and far off limb measurements in the equatorial plane in Mg IX, Ne VIII, and O VI lines. We discuss the potential to use abundance diagnostics methods to study the variability of the elemental composition that can be compared with in situ measurements to help confirm the magnetic connection between the spacecraft location and the Sun’s surface, and locate the sources of the solar wind. Conclusions. The SPICE instrument successfully performs measurements of EUV spectra and raster images that will make vital contributions to the scientific success of the Solar Orbiter mission

Sun: UV radiation↗
DOE OSTI2021

Tailoring Cementitious Materials Towards Value-Added Use of Large CO 2 Volumes

Hydraulic cements with alternative chemistries were developed for large-volume and value-added use of carbon dioxide. The hydraulic cements were processed using the energy-efficient mechanochemical technique at room temperature and atmospheric pressure. Carbon dioxide was captured directly from combustion emissions during processing. For this purpose, mechanochemical processing of hydraulic cements was accomplished under a flow of combustion emissions prior to the release of emissions to the atmosphere. The process removed a significant fraction of carbon dioxide from combustion emissions. The hydraulic cements captured carbon dioxide at about 10% of their weight. Two hydraulic cement chemistries were developed, and their mechanochemical processing was successfully scaled-up. The characteristic feature of one chemistry was its relatively low (near-neutral) pH where the integration of carbon dioxide yielded clear value. The second cement chemistry was based on alkali activation of industrial wastes. This chemistry could make value-added use of carbon dioxide, but it had to be refined to control the pH drop caused by CO 2 integration. These two cements render binding effects upon hydration by forming a combination of stable carbonates and aluminosilicates or phosphates. Efforts to develop cement chemistries based solely on carbonates were not successful. The mechanochemical process was found to integrate carbon dioxide into the alternative cement chemistries in the form of disordered and metastable carbonates. During hydration reactions, the disordered/metastable carbonates are either transformed into stable carbonate phases with desired binding efforts, or carbonates get integrated into the primary inorganic binders (hydrates). When compared with mechanochemical processing in pure carbon dioxide, mechanochemical processing in combustion emissions produced hydraulic cements with improved engineering properties. The mechanochemical process was scaled-up, and its variables as well as the raw materials formulations were optimized for implementation at pilot scale. Scale-up was found to enhance the carbon capture potential and the engineering qualities of the resulting hydraulic cements. This was because scale-up raises the intensity of mechanical energy input to raw materials. Certain mechanochemical phenomena cannot be induced, irrespective of the cumulative mechanical energy input, unless the intensity of impact is raised above a minimum level that cannot be achieved in laboratory-scale implementation of the process. Due to this effect, the duration of the mechanochemical process as well as its energy demand could be reduced significantly (by an order of magnitude) upon transition from laboratory to pilot scale, with the hydraulic cements produced at pilot scale offering engineering properties that were superior to those realized in laboratory-scale mechanochemical processing. The hydraulic cements produced at pilot scale via mechanochemical processing under a flow of combustion emissions were thoroughly characterized. They were found to meet standard requirements for ‘General Use’ hydraulic cements. They were compatible with the industrial-scale concrete production and construction practices that are used with the currently prevalent hydraulic cements. The new hydraulic cements with integrated carbon dioxide were found to offer distinct advantages over the currently prevalent Portland cement in terms of net carbon footprint and energy content. The combined raw materials and energy costs of the new hydraulic cements are competitive, and major cost savings can be realized because of the simplified production process that significantly lowers the capital investment in cement production plants. Mechanochemical processing of the new hydraulic cements under a flow of combustion emissions can be implemented using some existing components of cement manufacturing plants; this facilitates adoption of the technology by the cement industry.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Initial assessment of alternative carbon fiber geometries for design of cost-effective compressive performance: Size effect studies

Carbon fiber provides opportunity to reduce weight in structural composites, including wind turbine blades, due to the material's superior specific stiffness and specific strength compared to alternatives. Despite these advantages, cost and compressive performance are considered weaknesses for carbon fiber products available today. Studies to produce low-cost carbon fiber alternatives, including the use of textile-derived precursor systems, have shown progress and merit through the DOE/ORNL low-cost carbon fiber initiatives. Here, this work focuses on enabling increases in compressive strength through design of the carbon fiber geometry, applicable to both textile and conventional precursor systems, while also providing opportunities to reduce carbon fiber processing costs. Fiber-resin interface and fiber alignment are among the most frequently cited factors controlling composite compressive performance. However, it is believed that there is opportunity in traditionally unexplored routes to increasing compressive strength through alteration of the carbon fiber geometry by increasing the fiber area moment of inertia and/or the fiber perimeter and interfacial area. This paper presents initial results from manufacturing carbon fiber materials to assess the impacts of carbon fiber size on tested composite compressive performance with projected neutral or even beneficial impact on fiber and composite manufacturing economics. Carbon fiber systems with increasing size illustrate a favorable correlation for compressive performance greater than predicted from a micromechanical failure model. The manufacturing and mechanical test results support the hypothesis of this work that alterations to fiber geometry can be used to produce improvements of the compressive strength of carbon fiber reinforced polymers and provide incentive for related work in designing alternative shapes to further enhance compressive performance.

42 ENGINEERING↗
DOE OSTI2022

Drivers of Decadal Carbon Fluxes Across Temperate Ecosystems

Long-running eddy covariance flux towers provide insights into how the terrestrial carbon cycle operates over multiple timescales. Here, we evaluated variation in net ecosystem exchange (NEE) of carbon dioxide (CO 2 ) across the Chequamegon Ecosystem-Atmosphere Study AmeriFlux core site cluster in the upper Great Lakes region of the USA from 1997 to 2020. The tower network included two mature hardwood forests with differing management regimes (US-WCr and US-Syv), two fen wetlands with varying levels of canopy sheltering and vegetation (US-Los and US-ALQ), and a very tall (400 m) landscape-level tower (US-PFa). Together, they provided over 70 site-years of observations. The 19-tower Chequamegon Heterogenous Ecosystem Energy-balance Study Enabled by a High-density Extensive Array of Detectors 2019 campaign centered around US-PFa provided additional information on the spatial variation of NEE. Decadal variability was present in all long-term sites, but cross-site coherence in interannual NEE in the earlier part of the record became weaker with time as non-climatic factors such as local disturbances likely dominated flux time series. Average decadal NEE at the tall tower transitioned from carbon source to sink to near neutral over 24 years. Respiration had a greater effect than photosynthesis on driving variations in NEE at all sites. Declining snowfall offset potential increases in assimilation from warmer springs, as less-insulated soils delayed start of spring green-up. Higher CO 2 increased maximum net assimilation parameters but not total gross primary productivity. Stand-scale sites were larger net sinks than the landscape tower. Clustered, long-term carbon flux observations provide value for understanding the diverse links between carbon and climate and the challenges of upscaling these responses across space.

54 ENVIRONMENTAL SCIENCES↗