Search NASA⌕ Search

SEARCH · Search NASA

Results for “impedance spectroscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Morphological Modulation of TiO 2 Nanotube via Optimal Anodization Condition for Solar Water Oxidation

With the depletion of fossil fuels and the rising global demand for energy, photoelectrochemical (PEC) water splitting presents a promising solution to avert an energy crisis. Titanium dioxide (TiO 2 ), an n -type semiconductor, has gained popularity as a photoanode due to its remarkable PEC properties. Nevertheless, inherent challenges such as a wide band gap (~3.2 eV), charge recombination, and slow oxygen evolution reaction (OER) rates at the surface limit its practical application by constraining light absorption. To overcome these limitations, we have developed TiO 2 nanotubes (NTs) using a facile anodization method. This study examines the impact of anodization growth parameters on solar water oxidation performance. Specifically, TiO 2 NTs with modified anodization time (referred to as TiO 2 -6) showed a 3.5-fold increase in photocurrent density compared to the as-grown TiO 2 NTs. Furthermore, electrochemical analyses, such as electrochemical impedance spectroscopy (EIS), indicated a significant decrease in charge transfer resistance following the adjustment of on-off anodization time. Additionally, the TiO 2 -6 photoanode demonstrated a higher electrochemically active surface area (ECSA) than other samples. Therefore, optimal nanostructuring parameters are crucial for enhancing the PEC properties of TiO 2 NTs. Overall, our findings offer valuable insights for fabricating high-quality TiO 2 NTs photoanodes, contributing to developing efficient PEC systems for sustainable energy production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Crosslinked Polyethyleneimine Gel Polymer Interface to Improve Cycling Stability of RFBs

Redox flow batteries are considered a promising technology for grid energy storage. However, capacity decay caused by crossover of active materials is a universal challenge for many flow battery systems, which are based on various chemistries. In this paper, using the vanadium redox flow battery as an example, we demonstrate a new gel polymer interface (GPI) consisting of crosslinked polyethyleneimine with a large amount of amino and carboxylic acid groups introduced between the positive electrode and the membrane. The GPI functions as a key component to prevent vanadium ions from crossing the membrane, thus supporting stable long-term cycling. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements were conducted to investigate the effect of GPI on the electrochemical properties of graphitic carbon electrodes (GCFs) and redox reaction of catholyte. X-ray photoelectron spectroscopy (XPS) and 1 H nuclear magnetic resonance (NMR) spectra demonstrated that the crosslinked GPI is chemically stable for 100 cycles without dissolution of polymers and swelling in the strong acidic electrolytes. Results from inductively coupled plasma mass spectrometry (ICP-MS), Fourier-transform infrared (FTIR) spectroscopy, and energy-dispersive X-ray (EDX) spectroscopy proved that the GPI is effective in maintaining the concentration of vanadium species in their respective half-cells, resulting in improved cycling stability because of it prevents active species from crossing the membrane and stabilizes the oxidation states of active species.

Lim, Hyung-Seok↗
DOE OSTI2024

High-current, high-voltage AlN Schottky barrier diodes

AlN Schottky barrier diodes with low ideality factor (<1.2), low differential ON-resistance (<0.6 mΩ cm 2 ), high current density (>5 kA cm −2 ), and high breakdown voltage (680 V) are reported. The device structure consisted of a two-layer, quasi-vertical design with a lightly doped AlN drift layer and a highly doped Al 0.75 Ga 0.25 N ohmic contact layer grown on AlN substrates. A combination of simulation, current–voltage measurements, and impedance spectroscopy analysis revealed that the AlN/AlGaN interface introduces a parasitic electron barrier due to the conduction band offset between the two materials. This barrier was found to limit the forward current in fabricated diodes. Further, we show that introducing a compositionally-graded layer between the AlN and the AlGaN reduces the interfacial barrier and increases the forward current density of fabricated diodes by a factor of 10 4 .

Quiñones, C. E. (ORCID:0000000192703747)↗
DOE OSTI2021

Mitigating CO 2 Corrosion of Natural Gas Steel Pipelines by Thermal Spray Aluminum Coatings

We report internal pipeline corrosion due to carbon dioxide (CO 2 ) is a major challenge facing the oil and gas industry. The objective of this study was to investigate the corrosion behavior of aluminum (Al)-based alloys as sacrificial coatings to protect pipelines in a CO 2 -saturated aqueous electrolyte (3.5 wt% NaCl) at 4 bar CO 2 partial pressure (3 bar) and 40°C. The corrosion resistance of Al-based alloys and thermal spray coatings was evaluated in an electrochemical reaction autoclave using electrochemical methods (potentiodynamic polarization, linear polarization resistance, and electrochemical impedance spectroscopy). Post-corrosion surface characterization was performed by scanning electron microscopy equipped with energy-dispersive x-ray spectroscopy. The obtained data show Al-based alloys demonstrated promising protection against CO 2 corrosion with no breakaway degradation issues.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Corrosion of Zinc Cold Spray Coatings in a Wet Sweet and Sour Gas Environment

Internal corrosion is a problem for steel pipelines transporting natural gas or CO 2 containing water and partial pressures of H 2 S higher than 0.3 kPa (0.05 psi). This work aims to mitigate internal corrosion in steel pipelines transporting natural gas containing H 2 S using cold spray coatings. Two types of the cold spray binary metallic coatings (zinc chromium [ZnCr]. zinc niobium [ZnNb]) were studied using electrochemical techniques: potentiodynamic polarization, linear polarization resistance, and electrochemical impedance spectroscopy. The corrosion resistance of cold spray coatings (ZnCr, ZnNb) was evaluated in an environment containing 4 bar CO 2 pressure, simulating the partial pressures found in gas transmission lines over a solution of 3.5 wt% NaCl heated to 40°C. A concentration of 0.003 M Na 2 S 2 O 3 ·5H 2 O, corresponding to H 2 S partial pressures around 0.079 bar (1.146 psi), was used to simulate sour conditions. Postcorrosion surface characterization was performed using a scanning electron microscope (SEM) equipped with an energy-dispersive x-ray spectroscope (EDS) and x-ray diffraction analysis. The data showed that the presence of 0.003 M Na 2 S 2 O 3 ·5H 2 O shifted the corrosion potential to more anodic values and decreased the corrosion current density. Both coatings showed similar behavior after 1 h of exposure in the CO 2 /H 2 S environment, indicating that similar electrochemical reactions were occurring on ZnNb and ZnCr. SEM images and EDS surface analyses for specimens showed a significant change in the surface chemical composition of carbon steel coated with ZnNb and ZnCr after 24 h of immersion. In the presence of thiosulfate (under sour conditions), the formation of corrosion product layers (ZnCO 3 and ZnS) on top of ZnNb and ZnCr coatings increased their corrosion resistance, which helped to reduce their corrosion by a factor of 2. Under a sweet environment, the corrosion rates for steel coated with cold spray coatings after 14 d of exposure are lower than that for galvanized steel by a factor of 5 due to the ZnCO 3 layer formed on top of the coatings. The ZnCO 3 layer formed on the steel surface acts as a physical barrier against corrosion by blocking the diffusion of corrosive species to the surface. No localized attack was observed. ZnCr Cold spray coating with defect showed promising corrosion protection against CO 2 corrosion (sweet corrosion) after 14 d of exposure to a CO 2 environment. Here, the scratch on the coating simulated damage created in service, and it was deep enough to expose the substrate material (steel). The formation of zinc oxide (ZnO) and zinc carbonate (ZnCO 3 ) on the scratch confirmed the cathodic protection of the steel by ZnCr and ZnNb coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Principles of Corrosion in Nuclear Systems: Theory and Analytical Methods

This article is meant to provide the reader with the fundamental electrochemistry necessary to critically evaluate the data and discussions in the articles on corrosion that follow. As such it has two main sections, theory and analytical methods. In the section on theory, a review of half cell reactions, cell potentials and the Nernst equation, and reference electrodes in nuclear systems are discussed. In addition, a review of the thermodynamics from room temperature to the PWR and kinetics of dissolution and passive film formation is also presented. In the section on analytical methods, we review the principles of potentiodynamic polarization, electrochemical impedance spectroscopy, and we introduce a more seldom used technique, Mott-Schottky analysis.

Lillard, R Scott↗
DOE OSTI2021

Novel Membrane-Based Corrosion Sensors For Operating In Natural Gas Pipelines

Membrane-based electrochemical sensors (MBES) provide an attractive option for real-time continuous humidity and corrosion rate measurements inside of natural gas pipelines. The MBES, can use electrochemical techniques such as linear polarization resistance and electrochemical impedance spectroscopy even when a conductive aqueous phase is intermittent or unavailable. We now present field-test performance data of our MBES operated inside a multiphase water and natural gas flow facility. The MBES measured internal corrosion and conductivity at the top, bottom, and side of the pipe spool. Tests were carried out with flow rates of 4.6, 9.1, and 18.3 m/s, temperatures of 21, 29, and 35 °C, and a pressure of 1000 psia. All sensors followed similar trends in open circuit potential, corrosion rate, and conductivity over time. Neither flow rate, temperature, nor build-up of metal-based solids on the sensor surfaces impacted the quality of the electrochemical measurements. The field-test results confirm that the membrane-based electrochemical sensors are suitable for monitoring internal corrosion of operational natural-gas pipelines.

Duffy, Timothy↗
DOE OSTI2021

Corrosion Behavior of Alloy Structural Steels in Catechol and Biomass-Derived Pyrolysis Oils

Electrochemical impedance spectroscopy (EIS) was used to assess the corrosion behavior of three steels, 2.25Cr-1Mo, 5Cr-1Mo and 9Cr-1Mo (UNS K21590, S50200 and K90941) in bio-oils and catechol, an organic constituent commonly found in bio-oils. Two types of biomass pyrolysis oils produced from selected forest residue feedstocks, classified as high-ash and high-moisture (HAHM) and low-ash and low-moisture (LALM) types and 10 wt.% catechol, were used to test the alloys. According to previous results, 10 wt.% catechol in a water and methanol mixture was corrosive to 2.25Cr-1Mo but not to 9Cr-1Mo, highlighting that increasing Cr content in the steels resulted in improved corrosion resistance. 5Cr-1Mo, a steel with an intermediate Cr content, was tested in catechol solutions to better estimate the critical value of Cr for corrosion resistance under these conditions. Also, the three alloys were tested in both HAHM and LALM bio-oils to assess corrosion susceptibility. For EIS measurements, a customized electrochemical setup was employed to minimize the ohmic path through the bio-oils. The corrosion susceptibility was evaluated by determining the resistance at the alloy-corrosive medium interface.

Jun, Jiheon↗
DOE OSTI2021

Evaluation of Corrosion Susceptibility of Structural Steels in Biomass Derived Pyrolysis Oil

Biomass derived pyrolysis oil is a promising renewable energy source. Due to the variety of biomass feedstocks, the bio-oils could contain a wide range of organic constituents which would provide unique corrosive environments for structural materials. A preliminary work exposed different classes of steels and stainless steels to selected organic constituents of biomass pyrolysis oils and found that corrosion susceptibility, assessed using electrochemical impedance spectroscopy (EIS), was prominent in the steels with Cr lower than 11 wt.%. Although this result suggests stainless steels will resist corrosion by certain organic constituents, it may not be sufficient to predict the corrosion performance in real bio-oils. Therefore, this study attempted electrochemical measurements on Cr-alloyed steels and stainless steels directly exposed to a biomass derived pyrolysis oil. To overcome the low conductivity of bio-oils, a customized Luggin capillary was designed to minimize the ohmic path in bio-oils. The results of this work will be reported.

Jun, Jiheon↗
DOE OSTI2021

Corrosion and Chemical Characterization of Bio-Oils from Biomass with Varying Ash and Moisture Contents

As part of the Feedstock Conversion Interface Consortium four samples of pine chips (all combinations of low and high moisture and ash content) were collected and processed for fast pyrolysis. The prepared biomass samples were liquefied at the National Renewable Energy Laboratory (NREL) using the fast pyrolysis process. Following some characterization of the bio-oils at NREL, the bio-oils were shipped to Oak Ridge National Laboratory (ORNL) for corrosion testing and further characterization.The content and composition of ash in each bio-oil was determined. Corrosion testing consisted of exposing selected metallic and elastomer samples for 1000 hr at 50°C and for longer times at room temperature as well as electrochemical impedance spectroscopy measurements to assess relative corrosivity of the bio-oils. Chemical characterization was conducted to identify the corrosive component of the bio-oils as well as to define the chemical differences among the oils. It was hypothesized that there could be a catalytic effect from the higher ash content in two of the biomass sources. Results of these characterization and corrosion studies will be reported.

Keiser, Jim↗
DOE OSTI2020

DOE-BU-26096-4

The infiltration of nanoparticle electrocatalysts into solid oxide fuel cell (SOFC) electrodes has been proven to produce a high density of electrochemically active sites, and reduce charge transfer polarization losses in SOFC electrodes. This is crucial for intermediate temperature operation, as these losses increase greatly at lower temperatures. Nickel-yttria stabilized zirconia (Ni-YSZ) cermets are low-cost, and exhibit excellent stability, but their main disadvantage stems from nickel coarsening and performance loss over their operational lifetimes. Infiltration of electrocatalyst nanoparticles has been shown to mitigate nickel coarsening and the consequent anode degradation. In this work, the effects of these infiltrants have been observed in a standard Ni-YSZ electrode. In addition to nickel, mixed ionic and electronic conducting (MIEC) phases have been infiltrated into Ni-YSZ scaffolds and their performance characterized using electrochemical impedance spectroscopy (EIS). Cross-sectional microscopy of fractured cells has been used to compare electrode microstructure and particle statistics. A model has been proposed to explain the origin of anode performance enhancement from nanoscale electrocatalysts.

Mo, Boshan↗
DOE OSTI2022

Electrochemical Corrosion of SIMFUEL: Effects of dissolved H2 and noble metal particles

This report describes the results from electrochemical corrosion tests that were conducted using simulated spent fuel (SIMFUEL) materials comprised of UO2 and surrogate fission products. Two SIMFUEL compositions were tested to quantify the effect of noble metal inclusions and dissolved H2 on the UO2 dissolution rate. One material consisted of UO2 with added lanthanide oxides (UO2 N) and the other consisted of UO2 with added lanthanide oxides and noble metals (UO2-H) at concentrations to simulate high burnup fuel. The electrochemical corrosion tests on the SIMFUEL materials were conducted in aqueous electrolyte solutions (pH 10) that were either saturated with air or purged with a H2/Ar gas mixture to maintain a constant dissolved H2 concentration. The results from electrochemical corrosion tests on SIMFUEL can be applied to qualitatively understand and also quantify the separate effects of water chemistry and fuel composition on the degradation behavior of the UO2 matrix. Open circuit potential (OCP) measurements on a SIMFUEL material of known composition (i.e., known fraction of NMPs at the fuel surface) immersed in a known solution chemistry (i.e., pH, Eh, [O2], [H2]) at known temperature provide qualitative insight into the degradation behavior of the UO2 matrix. If the OCP is above the threshold potential at which the oxidative dissolution of U(IV) to U(VI) occurs, the SNF is expected to degrade by oxidative processes under the experimental conditions. The net currents that are measured during potentiostatic tests, during which the surface potential of the SIMFUEL material is fixed by a potentiostat, can be used to quantify the UO2 degradation rate and optimize the rate constant values used in the Fuel Matrix Degradation Model (FMDM) for half reactions that occur on the SNF surface. Specifically, electrochemical measurements enable the estimation of the total anodic current at ECORR–which is the surface potential at which the total anodic and total cathodic currents are equal–so that the rate constant values for key reactions can be calculated. The open circuit potential measurements, potentiostatic tests, surface property measurements (scanning electron microscopy images and electrochemical impedence spectroscopy plots), and solution elemental composition analyses are being performed to update and optimize the FMDM. A case study is presented herein to show how electrochemical corrosion test results and accompanying characterization results for the UO2 N material in air-saturated solution can be used to validate the SNF surface reaction module of the FMDM. Future electrochemical tests will be conducted to provide quantitative information on the effects of NM content (burnup), H2 concentration, water chemistry, temperature, and galvanic couples with cladding and EBS alloys on UO2 degradation that can be used to improve the accuracy and functionality of the FMDM.

Thomas, Sara↗
DOE OSTI2023

Fundamentals of SrCoO 3-δ Based Oxygen Deficient Perovskites as Cathodes for Solid Oxide Fuel Cells

The local structure and oxygen stoichiometry in oxide systems have a profound impact on oxygen electrocatalysis encountered in metal-air batteries and solid oxide fuel cells (SOFCs). However, this knowledge is often obtained under conditions different from the real working conditions of the material, resulting in misinterpretation and misunderstanding. This PhD dissertation aims to obtain the structure and oxygen-stoichiometry information of a class of perovskite oxides under their real working conditions in solid oxide fuel cells. Several perovskite oxides were selected for the study: Sr 0.9 Y 0.1 CoO 3-δ (SYC10), Sr 0.9 Y 0.3 CoO 3-δ (SYC30), SrCo 0.9 Nb 0.1 O 3-δ (SCN10) and SrCo 0.9 Ta0.1O 3-δ (SCT10). The local crystal structure and oxygen stoichiometry of these materials were systematically characterized with in-situ neutron diffraction (ND). The oxygen stoichiometry was also measured by thermogravimetric analysis (TGA) and iodometric titration methods. To establish the correlation among structure, oxygen stoichiometry and oxygen reduction reaction (ORR) activity, high temperature electrochemical impedance spectroscopy, oxygen permeation and single cell testing were also performed. In chapter 2, SYC10 is described to have a more symmetrical structure and $V_o^{&middot;&middot;}$ distribution, and higher $V_o^{&middot;&middot;}$ concentration than SYC30. Molecular orbital energy analysis based on the local structure of the ORR-active Co1-polyhedra indicates SYC30 has a higher Fermi level relative to O-2p energy level in the active Co1-polyhedra, and thus a higher motional enthalpy for $V_o^{&middot;&middot;}$ migration. However, the ORR activity of Y-doped SrCoO 3-δ (SCO) are found uncompetitive with other popular catalysts. In chapter 3 and 4, systematic structural studies are presented for Nb and Ta-doped SCO, namely SCN10 and SCT10, respectively. The methodology of unrevealing the structure-activity relationships in chapter 2 is also found applicable to SYC10, SCN10 and SCT10 as presented in chapter 5. The electrochemical tests indicate that SCT10 is the best catalyst due to its excellent thermal and electrochemical stability. In chapter 6, SCT10 is evaluated in a real solid oxide fuel cell in the form of nanoscaled SCT10 layer coating on the commercial (La 0.6 Sr 0.4 ) 0.95 Co 0.2 Fe 0.8 O 3-δ (LSCF). The bilayer structured cathode shows excellent properties of coarsening-resistant, Sr-segregation-free and high ORR-activity.

Yang, Tianrang↗
DOE OSTI2023

Microstructural, Corrosion and Mechanical Characterization of Friction-Stir Welded Joints Between Aluminum and Magnesium Alloys

Friction Stir Welding (FSW) of Aluminum-Magnesium (Al-Mg) alloys has garnered increasing attention due to its wide-ranging applications in the automotive and aerospace industries. The microstructural, corrosion, and mechanical properties of FSW Al-Mg welds under selected conditions are critical factors that must be well-investigated to ensure their durability and performance. In this study, electrochemical tests, including Open Circuit Potential (OCP), Linear Polarization Resistance (LPR), Potentiodynamic Polarization Scan (PD), and Electrochemical Impedance Spectroscopy (EIS), have been used to analyze the corrosion resistance of these welds, along with weight loss measurements through cyclic corrosion testing (CCT) and surface evolution via SEM over an 8-week period. Mechanical properties are evaluated through microindentation, nanoindentation, fatigue, and lap-shear tests. The results of the electrochemical tests reveal that the corrosion properties of the center weld zone differ from those of the two base alloys. Indentation tests indicate that the weld zone behaves differently from the base alloys. Surprisingly, the lap shear strength did not decrease significantly even after 8 weeks of cyclic corrosion testing, indicating that the joint prevented any ingress of the electrolyte. Fatigue testing showed that applying an adhesive between the Al and Mg joint improved the fatigue life to some extent, although the corrosion resistance reduced due to the discontinuous bonding of the adhesive layer. Overall, these findings highlight the importance of investigating the corrosion and mechanical properties of FSW Al-Mg welds and provide valuable insights for future modeling works.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Effect of Minor Ce Additions on Corrosion Behavior of Experimental Pipeline Steel

Minor additions of rare earth elements (REEs) have been shown to improve various steel properties. In particular, Cerium (Ce), as a relatively abundant and inexpensive element, has received attention as a potentially beneficial minor alloying addition for a variety of steel applications, including pipelines materials. The objective of this work is to investigate the effect of Ce on corrosion performance of experimental high-strength pipeline steel. Electrochemical corrosion experiments were carried out on steel without and with 0.006, 0.018, and 0.03 wt.% of Ce in 3.5 wt.% NaCl saturated with CO2 at 20 oC. For comparison purposes, X100 carbon steel specimens machined from an experimental pipe with a yield strength of 731 MPa were tested under the same conditions. The electrochemical techniques employed included: potentiodynamic polarization (PDP), linear polarization resistance (LPR), and electrochemical impedance spectroscopy (EIS). In addition, post-corrosion surface characterization was performed using scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), while crystalline phases were determined by X-ray diffraction (XRD). The corrosion of base metal without Ce was lower (0.15 mm/y) compared to carbon steel X100 (0.9 mm/yr). The electrochemical results showed that adding Ce accelerates corrosion rates compared to base metal without Ce. No pitting corrosion of tested steel was detected.

Belarbi, Zineb↗
DOE OSTI2025

Faraday Slidedeck

Faraday is a data science and visualization platform for electrochemical impedance spectroscopy. The slide deck is a visual guide with high-level information pertaining to the background, theory, and development of the application.

data warehouse↗
DOE OSTI2025

Current interrupt method for calculating the electrochemical impedance in a solid oxide electrolysis stack

Here, in this work the time domain response of Solid Oxide Electrolysis Cells (SOEC) to a current interruption was transformed into the frequency domain using a carrier function Laplace transform, which is fit to the experimental data using a MATLAB Complex Nonlinear Least Squares (CNLS) solver. The hardware implementation, consisting principally of a high-speed switch and a fast-logging Analog to Digital Converter (ADC), was assembled and tested using a calibration module to assess the accuracy, repeatability, and speed of acquisition of the prototype device as compared against a calibrated commercial impedance spectrometer. Additionally, the current interrupt device and commercial FRA were used to acquire the impedance spectra of a four cell SOEC stack with a large, 300 cm 2 , active cell area.

SOEC↗
DOE OSTI2024

4 V Na Solid State Batteries Enabled by a Scalable Sodium Metal Oxyhalide Solid Electrolyte

All-solid-state sodium batteries (ASSSBs) are viable candidates for large scale energy storage that could vie with lithium. Ductile solid catholytes for such cells that can be prepared without extensive ball milling and directly paired with high voltage sodium cathodes are lacking, however. We report a new amorphous fast Na-ion conducting metal oxychloride that meets these criteria, synthesized through a scalable and low-cost route based on a spontaneous solid-state reaction with simple short mixing and 100 °C annealing. It has an ionic conductivity of 1.2 mS·cm–1 and low activation energy of 0.31 eV. Due to its dual O2–/Cl– framework, it exhibits a high anodic potential of 4 V vs Na+/Na and good chemical/electrochemical compatibility with high voltage sodium cathode materials. ASSSBs consisting of the oxychloride solid electrolyte paired with a high voltage P2–Na2/3Ni1/3Mn2/3O2 cathode showed stable long-term cycling with a 4.0 V vs Na3Sn cutoff potential and even to 4.3 V.

solid-state electrolyte, solid-state batteries, Nu↗