Search NASA⌕ Search

SEARCH · Search NASA

Results for “sample thickness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Magnification Determination for AGHCF Metallographic Images

Metallographic images generated in the Alpha Gamma Hot Cell Facility (AGHCF) have been used for quantitative and qualitative characterization of irradiated metallic fuel pins. Individual high-magnification images (micrographs) contained in AGHCF file folders and experimental notebooks are in the form of polaroid photographs labeled with AGHCF identification number, magnification, and surface condition (as-polished or etched). Low magnification composite images (photomosaics) are also available for fuel cross sections, for radial strips from the fuel center to the cladding outer diameter, and for circumferential strips of the cladding and outer fuel region. The individual images do not have scale bars. Only a few of the composite images contain scale bars. The purpose of this work is to describe and apply methods for checking the magnification (50X to 500X) of individual images and for determining the magnification (~25X to ~100X) of composite images. The metallographic images used to verify and/or determine magnification were generated during the 1989 to 1993 timeframe for cross sections of U-10Zr/HT9 fuel rods irradiated in EBR-II and for cross sections of irradiated U-10Zr/HT9 fuel-rod samples following elevated-temperature tests conducted in the out-of-pile AGHCF Fuel Behavior Test Apparatus (FBTA). Procedures are documented in the AGHCF Operations Manual for preparation of metallographic samples, for calibration verification, and for constructing composites from individual images. Calibration verification of magnification was performed at least semiannually. One standard used for calibration verification was a glass slide with vertical lines indicating distances of 1 mm, 0.1 mm and 0.01mm. Guidance is provided in the current work for determining magnification from images of the standard. In addition to the periodic calibration verification, consistency checks are recommended to verify the magnification of images taken between the routine calibration verifications. For cladding samples with or without significant fuel-cladding chemical interaction (FCCI), images taken at different magnifications (e.g., 150X and 200X) of the unaffected cladding thickness can be compared. This process is independent of changes in cladding thickness due to swelling and creep. For images taken at only one magnification of cladding regions with no FCCI, the cladding thickness determined from the images may be compared to the nominal as-built cladding thickness (15.0 ± 0.5 mils for examples used in current work)). This procedure works best for cladding that has not experienced significant swelling and/or creep (e.g., ≤2% circumferential strain at the cladding outer surface). Composite images were constructed by pasting together higher magnification images and photographing the composite to generate a negative from which the hard-copy photograph was developed. The primary purpose of the composite images was to identify interesting areas of the fuel and cladding for imaging at higher magnification. However, procedures are recommended in the current work for determining composite magnifications to allow quantitative characterization of the fuel. Composites are not recommended for determining cladding thickness or FCCI depth because magnifications are too low (generally ≤110X) and image contrast is low. Fuel cross-section composites were created by pasting together 50X or 75X images. The nominal magnification for the photographed fuel cross-section composites is 25.4X. A more precise magnification can be determined by comparing the average cladding outer diameter measured from the composite to the average cladding outer diameter measured by profilometry. Radial-strip composites were constructed by pasting together high-magnification (150X or 250X) images. The nominal magnification of radial-strip composites photographs is about 100X. A more precise method for determining the magnification of radial strips is to compare the cladding thick

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Investigating the vertical distribution of the disk as a function of radial action

As heating processes can broaden the distributions of radial actions and the vertical distributions of the Galactic disks, we investigate the vertical distribution of the Galactic disks as a function of radial action based on Apache Point Observatory Galactic Evolution Experiment (APOGEE) and Gaia data in order to deepen our understanding of the formation and heating history of the Galactic disks. The vertical distributions of the thin and thick Galactic disks defined in the chemical plane were fitted with a simple exponential function with a free parameter of scale height in different radial action ranges. Therefore, we were able to analyze the scale height as a function of radial action for different disk populations. We find that the distributions of radial action for both the thin and thick disks can be approximately described by pseudo-isothermal distributions, which give a statistical measurement for the temperature of the disk as indicated by the mean radial action of the star sample. Estimations of the scale heights in different radial action ranges for these pseudo-isothermal distributions of the disks seem to show fixed relationships between radial action J R and scale height h. We describe these relationships with a two-parameter function of h = √(J R /a)+b, where a and b are free parameters. When testing with a three-parameter function of h = α √(J R /a)+b, we find that this two-parameter function describes the thin disk well, but we note the function should be used with care for the thick disk. When comparing the best-fit relationships between the inner and outer disk for both of the thin and thick disks, we find that the relationships are nearly the same for the thin disks but are different for the thick disks. The inner thick disk shows a nearly flattened relationship, while the outer thick disk presents a gradually increasing relationship. This work highlights an alternative way to unveil the heating history of the disks by investigating the relationship between scale height and radial action, as these relationships encode the formation and heating history of the Galactic disks.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Epitaxial (Al x Ga 1-x-y In y ) 2 O 3 Alloys Lattice Matched to Monoclinic Ga 2 O 3 Substrates

We have epitaxially stabilized a series of monoclinic (Al x Ga 1-x-y In y ) 2 O 3 alloys by careful choice of molecular beam epitaxy growth conditions, which balance alloy growth with suboxide desorption. The films are pseudomorphic to (010) β-Ga 2 O 3 substrates at thicknesses up to 150 nm with compositions ranging from (Al 0.01 Ga 0.83 In 0.16 ) 2 O 3 to (Al 0.24 Ga 0.75 In 0.03 ) 2 O 3 . The absorption edge shifts from approximately 4.62-5.14 eV with coincidently increasing Al and decreasing In mole fractions. J-V measurements reveal an increase in resistivity over four orders of magnitude with a maximum value of 4.2 x 10 5 Ω-cm for (Al 0.17 Ga 0.76 In 0.07 ) 2 O 3 , which has nearly identical lattice parameters (both in-plane and out-of-plane) to the underlying β-Ga 2 O 3 . Scanning transmission electron microscopy of this sample reveals a mostly uniform and single crystalline film, though we identify areas of non-uniform In incorporation and some γ-phase inclusions. This work demonstrates the feasibility of thick layers lattice-matched to β-Ga 2 O 3 with increased bandgap compared to phase-separation limited (Al,Ga) 2 O 3 . These alloys can enable higher bandgap epitaxial dielectrics and high sheet charge density transistors by increasing the conduction band offset with respect to β-Ga 2 O 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure

Swings in pH can be achieved by electrically polarizing a bipolar membrane (BPM) to drive water dissociation at the BPM junction for electrochemical conversion and separation processes. BPM junction design is critical to tailor performance for specific applications; however, characterization techniques capable of resolving the nanometer scale physical structure of the junction are limited. We present sample preparation, imaging, and analysis workflows that are adaptable to a variety of BPM junction architectures. Atomic force microscopy produces BPM junction images with nanometer scale lateral resolution for samples with and without a graphene oxide water dissociation catalyst in the junction. Subsequent image segmentation and analysis quantify line edge roughness and catalyst layer thickness as descriptors of junction structure. Comparison of pre- and post-electrodialysis junctions suggests electric field-induced alignment of catalyst particles during electrodialysis. This characterization workflow can inform manufacturing protocols, computational modeling, and failure mode analysis for next-generation BPMs.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Characterization of a 1D-imaging high-energy x-ray backlighter driven by the National Ignition Facility Advanced Radiographic Capability laser

Plastic deformation of samples compressed to Mbar pressures at high strain rates at the National Ignition Facility (NIF) forms the basis of ongoing material strength experiments in conditions relevant to meteor impacts, geophysics, armor development, and inertial confinement fusion. Hard x-ray radiography is the primary means of measuring the evolution of these samples, typically employing a slit-collimated high-Z microdot driven by the NIF laser to generate >40 keV x rays [E. Gumbrell et al., Rev. Sci. Instrum. 89, 10G118 (2018) and C. M. Huntington et al., Rev. Sci. Instrum. 89, 10G121 (2018)]. Alternatively, a dysprosium “micro-flag” target driven by the Advanced Radiographic Capability laser (~2 kJ, 10 ps) can deliver significantly higher spatiotemporal resolution [M. P. Hill et al., Rev. Sci. Instrum. 92, 033535 (2021)], especially in high-opacity samples. Here, initial experiments revealed problematic brightness and spectral gradients from this source, but by radiographing a set of diamond-turned, 105 µm-thick Pb test objects and supported by simulations using the 3D Monte Carlo code GEANT4, these geometry-dependent gradients across the field of view are quantified and mitigation strategies are assessed. In addition to significantly enhancing the modulation transfer function compared to the existing system, image stacking from multiple layers of image plate is shown to almost double the signal to noise ratio that will reduce uncertainties in future dynamic strength experiments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Spatially correlated incommensurate lattice modulations in an atomically thin high-temperature Bi 2.1 Sr 1.9 CaCu 2.0 O 8+y superconductor

Strong variations in superconducting critical temperatures in different families of the cuprate perovskites, even with similar hole doping in their copper-oxygen planes, suggest the importance of lattice modulation effects. The one-dimensional incommensurate lattice modulation (ILM) of Bi 2 Sr 2 CaCu 2 O 8+y , with the average atomic positions perturbed beyond the unit cell6, offer s an ideal test ground for studying the interplay between superconductivity and the long-range incommensurate lattice fluctuations. Here we report Scanning nano X-ray Diffraction (SnXRD) imaging of incommensurate lattice modulations in Bi 2 Sr 2 CaCu 2 O 8+y Van der Waals heterostructures of thicknesses down to two-unit cells. Using SnXRD, we probe that the long-range and short-range incommensurate lattice modulations in bulk sample surface with spatial resolution below 100 nm. We find that puddle-like domains of ILM of size uniformly evolving with dimensionality. In the 2-unit cell thin sample, it is observed that the wavevectors of the long- and short-range orders become anticorrelated with emerging spatial patterns having a directional gradient. The emerging patterns, originated by tiny tuning of lattice strain, induce static mesoscopic charge density waves. Finally, our findings thus demonstrate that the strain can be used to tune and control the electromagnetic properties of two-dimensional high-temperature superconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The Global Structure of the Milky Way’s Stellar Halo Based on the Orbits of Local Metal-poor Stars

We analyze the global structure of the Milky Way (MW)'s stellar halo, including its dominant subcomponent, Gaia-Sausage-Enceladus (GSE). The method for reconstructing the global distribution of this old stellar component is to employ the superposition of the orbits covering the large MW's space, where each of the orbit-weighting factors is assigned following the probability that the star is located at its currently observed position. The selected local, metal-poor sample with [Fe/H] <–1, using Gaia Early Data Release 3 and Sloan Digital Sky Survey Data Release 16, shows that the global shape of the halo is systematically rounder at all radii in more metal-poor ranges, such that an axial ratio, q, is nearly 1 for [Fe/H] <–2.2 and ~0.7 for –1.4 < [Fe/H] < –1.0. It is also found that a halo in the relatively metal-rich range of [Fe/H] >–1.8 actually shows a boxy/peanut-like shape, suggesting a major merger event. The distribution of azimuthal velocities shows a disk-like flattened structure at –1.4 < [Fe/H] < –1.0, which is thought to be the metal-weak thick disk. For the subsample of stars showing GSE-like kinematics, at [Fe/H] >–1.8, its global density distribution has an axis ratio of 0.9, which is more spherical than the general halo sample, and an outer ridge at r ~ 20 kpc. This spherical shape is consistent with the features of accreted halo components, and the ridge suggests that the orbit of GSE's progenitor had an apocenter of ~20 kpc. Implications for the formation of the stellar halo are also presented.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

The Stellar Velocity Distribution Function in the Milky Way Galaxy

The stellar velocity distribution function in the solar vicinity is reexamined using data from the Sloan Digital Sky Survey Apache Point Observatory Galactic Evolution Experiment (APOGEE) survey’s DR16 and Gaia DR2. By exploiting APOGEE’s ability to chemically discriminate with great reliability the thin-disk, thick-disk, and (accreted) halo populations, we can, for the first time, derive the three-dimensional velocity distribution functions (DFs) for these chemically separated populations. We employ this smaller but more data-rich APOGEE+Gaia sample to build a data-driven model of the local stellar population velocity DFs and use these as basis vectors for assessing the relative density proportions of these populations over the 5 < R < 12 kpc and −1.5 < z < 2.5 kpc range as derived from the larger, more complete (i.e., all-sky, magnitude-limited) Gaia database. We find that 81.9% ± 3.1% of the objects in the selected Gaia data set are thin-disk stars, 16.6% ± 3.2% are thick-disk stars, and 1.5% ± 0.1% belong to the Milky Way stellar halo. We also find the local thick-to-thin-disk density normalization to be ρ {sub T}(R {sub ⊙})/ρ {sub t}(R {sub ⊙}) = 2.1% ± 0.2%, a result consistent with, but determined in a completely different way from, typical star-count/density analyses. Using the same methodology, the local halo-to-disk-density normalization is found to be ρ {sub H}(R {sub ⊙})/(ρ {sub T}(R {sub ⊙}) + ρ {sub t}(R {sub ⊙})) = 1.2% ± 0.6%, a value that may be inflated due to the chemical overlap of halo and metal-weak thick-disk stars.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Microstructure Experiments-Enabled MARMOT Simulations of SiC/SiC-based Accident Tolerant Nuclear Fuel System

We have undertaken an experimental-computational project that addresses a few key technology gaps associated with the use of SiC/SiC composites for light water reactor fuel cladding. Two principal endeavors in this project are to assess the irradiation-induced microstructural changes and swelling in SiC/SiC composites, and to characterize and model the porous oxide surface layer (when exposed to steam) along SiC recession that is detrimental to the clad integrity under accident conditions. The project tasks are: (i) ion irradiation and characterization (University of Tennessee, Knoxville), (ii) mechanical tests and analysis (University of South Carolina), (iii) steam exposure tests (Oak Ridge National Laboratory), (iv) electron microscopy and spectroscopic characterization (NC State University), (v) x-ray microscopy and reconstruction (University of South Carolina and NC State University), (vi) phase field modeling and simulations (NC State University and Idaho National Laboratory). The effects of 10 MeV Au ion irradiation at 350°C on the microstructure evolution in SiC/SiC composites are investigated at doses up to 400 displacements per atom (dpa) at the University of Tennessee, Knoxville. Atomic force microscopy and optical profilometry reveal irradiation induced axial and radial shrinkage of the fibers for doses greater than 10 dpa. Based on detailed electron microscopy characterization, the primary cause of the fiber shrinkage is attributed to irradiation-induced loss of carbon packets. Additionally, the multilayer PyC interface is observed to portray high resistance to irradiation damage. The mechanical response and failure mechanisms of un-irradiated samples is also assessed through loading tests and X-ray imaging at the University of South Carolina. Steam exposure tests are performed at the Oak Ridge National Laboratory in a facility that represents a reactor pressure vessel under a loss-of-coolant-accident scenario. The samples that are analyzed methodically in this report are tested for 32/31 hours at 1200°C with a velocity of 0.25 cm/s for the pressures: 0.1 MPa, 0.45 MPa, 0.92 MPa and 1.38 MPa. Scanning/transmission electron microscopy analysis conducted at the NC State University (NCSU) shows that the oxide layer thickness increases with the steam pressure. While the oxide layer is crystalline (α- cristobalite) for the pressures 0.45 MPa, 0.92 MPa and 1.38 MPa, the layer is amorphous at 0.1 MPa. Results from Raman spectroscopy have also confirmed the formation of α-cristobalite phase of SiO₂. The abrupt increase in the integrated Raman intensity ratio between steam pressures 0.1 and 0.45 MPa suggests the onset of accelerated crystallization. Non-destructive three dimensional X-ray microscopy/tomography (XCT) and computational image processing techniques are employed by the University of South Carolina to probe the porous oxidation features on SiC samples at varying pressures. Interestingly, most pores are observed to be located away from the surface as well as the oxide-SiC interface. The average oxide layer thickness assessed from the XCT analysis is seen to be in excellent agreement with the values determined through scanning electron microscopy analysis for the highest pressures where the oxide layer is relatively more uniform. A phase-field model developed by the NC State University and Idaho National Laboratory for simulating oxidation of SiC by steam captures the paralinear kinetics of SiC oxidation with a high degree of fidelity. Results from quasi-one-dimensional and two dimensional simulations show that the pores with oxidizing species lead to a higher volatilization rate. These simulations indicate that the enhanced apparent volatilization rates at higher pressures observed in experiments can be rationalized by the increased volatilization from the pores. The project team has also successfully developed the capability to import images from experiments for realistic evolution of the oxidizing microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Constraints on White Dwarf Hydrogen Layer Masses Using Gravitational Redshifts

The hydrogen envelope is the outermost layer of a DA white dwarf; it makes up the entirety of the stellar photosphere, and yet its typical extent is difficult to model theoretically and remains poorly observationally constrained. As a result, hydrogen envelope mass is a substantial source of systematic uncertainty in the physical properties of white dwarfs, including overall masses and cooling ages. In this work, we fit a Gaussian mixture model to gravitational redshifts from high-resolution spectroscopy, paired with radius measurements from Gaia BP/RP spectra, to measure the mass–radius relation for a sample of 468 white dwarfs. Our results are in excellent agreement with the predicted mass–radius relations of state-of-the-art evolutionary models, including those from the MESA Isochrones and Stellar Tracks (MIST) library. We find that mass–radius relations such as those from MIST that assume a thick and mass-dependent hydrogen envelope are preferred by the observed probability density function over models that assume a hydrogen envelope of constant mass. Proper treatment of the evolution of white dwarf progenitors is thus important for accurately modeling the mass–radius relation. Our results indicate that gravitational redshift measurements of large samples of white dwarfs in wide binaries are promising probes of the hydrogen envelope masses of DA white dwarfs.

Astronomy and AstroPhysics↗
DOE OSTI2024

Scanning SQUID study of ferromagnetism and superconductivity in infinite-layer nickelates

Infinite-layer nickelates R 1-x Sr x NiO 2 (R = La, Pr, Nd) are a class of superconductors with structural similarities to cuprates. Although long-range antiferromagnetic order has not been observed for these materials, magnetic effects such as antiferromagnetic spin fluctuations and spin-glass behavior have been reported. Different experiments have drawn different conclusions about whether the pairing symmetry is s or d wave. In this paper, we applied a scanning superconducting quantum interference device (SQUID) to probe the magnetic behavior of film samples of three infinite-layer nickelates (La 0.85 Sr 0.15 NiO 2 , Pr 0.8 Sr 0.2 NiO 2 , and Nd 0.775 Sr 0.225 NiO 2 ) grown on SrTiO 3 (STO), each with a nominal thickness of 20 unit cells. In all three films, we observed a ferromagnetic background. We also measured the magnetic susceptibility above the superconducting critical temperature in Pr 0.8 Sr 0.2 NiO 2 and La 0.85 Sr 0.15 NiO 2 and identified a non-Curie-Weiss dynamic susceptibility. Both magnetic features are likely due to NiO x nanoparticles. We investigated superconductivity in Pr 0.8 Sr 0.2 NiO 2 and Nd 0.775 Sr 0.225 NiO 2 , which exhibited inhomogeneous diamagnetic screening. The superfluid density inferred from the diamagnetic susceptibility in relatively homogeneous regions shows T-linear behavior in both samples. Finally, we observed superconducting vortices in Nd 0.775 Sr 0.225 NiO 2 . We determined a Pearl length of 330 µm for Nd 0.775 Sr 0.225 NiO 2 at 300 mK, both from the strength of the diamagnetism and from the size and shape of the vortices. These results highlight the importance of considering NiO x particles when interpreting experimental results for these films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Separation of Artifacts from Spin–Torque Ferromagnetic Resonance Measurements of Spin–Orbit Torque for the Low–Symmetry Van der Waals Semi–Metal ZrTe 3

Spin-orbit torques generated by exfoliated layers of the low-symmetry semi-metal ZrTe 3 are measured using the spin-torque ferromagnetic resonance (ST-FMR) technique. When the ZrTe 3 has a thickness greater than about 10 nm, artifacts due to spin pumping and/or resonant heating can cause the standard ST-FMR analysis to overestimate the true magnitude of the torque efficiency by as much as a factor of 30, and to indicate incorrectly that the spin-orbit torque depends strongly on the ZrTe 3 layer thickness. Artifact-free measurements can still be achieved over a substantial thickness range by the method developed recently to detect ST-FMR signals in the Hall geometry as well as the longitudinal geometry. ZrTe 3 /Permalloy samples generate a conventional in-plane anti-damping spin torque efficiency ξ$^{FL}_{∥}$ = 0.014 ± 0.004, and an unconventional in-plane field-like torque efficiency |ξ$^{FL}_{∥}$| = 0.003 ± 0.001. As a result, the out-of-plane anti-damping torque is negligible. It is suggested that artifacts similarly interfere with the standard ST-FMR analysis for other van der Waals samples thicker than about 10 nm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Characterization of fluidized bed chemical vapor deposition ZrC coatings on PyC/YSZ kernels deposited under differing conditions

In this study, coated fuel particle architectures with ZrC coatings are candidate fuels for advanced power reactors and space nuclear propulsion (SNP) concepts. Owing to its relevance to SNP, the composition, microstructure, and mechanical properties of eight ZrC coatings prepared by fluidized bed chemical vapor deposition were evaluated. Evaluation by SEM and EBSD showed that all grains were columnar. Across the various examined samples, minor axis diameters varied between 0.3 and 1.1 μm, and major axis diameters varied between 0.4 and 2.3 μm. Major and minor diameters increased with thickness particularly at higher deposition temperatures in which the major grain axis (from an ellipse fit to the grain shape) increased by 2.5 μm over the entire coating. Coatings with higher reactive gas flows and Zr/C concentrations closer to 1 were observed to contain nanocrystalline graphite deposits. Reactive gas flow doubling led to increases in coating thickness from around 10–15 μm to around 22–27 μm.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

ATLAS-MAP: An Automated Test Station for Gated Electronic Transport Measurements

The diversification of electronic materials in devices provides a strong incentive for methods to rapidly correlate device performance with fabrication decisions. In this work, we present a low-cost automated test station for gated electronic transport measurements of field-effect transistors. Utilizing open-source PyMeasure libraries for transparent instrument control, the “ATLAS-MAP” system serves as a customizable interface between sourcemeters and samples under test and is programmed to conduct transfer curve and van der Pauw methods with static and sweeping gate voltages. Zinc oxide transistors of variable thickness (5, 10, and 20 nm) and channel size (50 μm to 3 mm, of equal length and width) were fabricated to validate the design. Standardization of testing procedures and raw data formatting enabled automated data analysis. A detailed list of parts and code files for the system are provided.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Canted standing spin-wave modes of permalloy thin films observed by ferromagnetic resonance

Non-collinear spin structures in materials that combine perpendicular and in-plane magnetic anisotropies are of great technological interest for microwave and spin wave-assisted magnetization switching. [Co/Pt] multilayers are well-known perpendicular anisotropy materials that have the potential to pin the magnetization of a soft magnetic layer, such as permalloy (Py), that has in-plane anisotropy, thereby forming a magnetic exchange spring. Here we report on multilayered [Co/Pt]/Pt/Py films, where an additional ultrathin Pt spacer has been included to control the coupling between the sub-units with in-plane and perpendicular magnetic anisotropy. Vector network analyser (VNA)-ferromagnetic resonance (FMR) measurements were made to obtain a complete picture of the resonant conditions, while the dynamical response of the sub-units was probed by synchrotron-based element- and phase selective x-ray detected FMR (XFMR). For all samples, only slight pinning of the dynamic magnetization of the Py by the [Co/Pt] was noted, and the FMR results were dominated by the 50 nm thick Py layer. Out-of-plane VNA-FMR maps reveal the presence of additional modes, e.g. a perpendicular standing spin-wave (PSSW) state. However, as the magnetic field is reduced below the saturation field, the PSSW state morphs continuously through a series of canted standing spin-wave (CSSW) states into a horizontal standing spin-wave (HSSW) state. The PSSW, CSSW and HSSW states are well described using a multilayer model of the Py film. The observation of CSSW modes is of particular relevance to microwave assisted magnetic recording, where microwave excitation stimulates precession of a soft layer canted out of plane by a pulsed magnetic field.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Greybox Thermal Parameter Identification of Electric Machine Stators

The parameters of electric machine thermal equivalent circuit networks are difficult to predict due to material and manufacturing uncertainties. In this paper, a Greybox system identification approach is used to identify parameters of electric machine stator lumped parameter thermal networks (LPTNs). LPTNs provide a low order, computationally efficient, dynamic model of temperatures at specific locations. Second and third order LPTN model structures are defined as state space equations with stator thermal parameters to be identified. To test the Greybox electric machine stator thermal system identification, five stator motorette prototypes were constructed with controlled variations in slot fill and slot liner thickness. The variation in the motorette thermal parameters and thermal time constants are detected using the Greybox identification. Special attention is given to the impact of sampling rate and Greybox data record length on parameter estimation accuracy.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Oxygen Vacancies in Niobium Pentoxide as a Source of Two-Level System Losses in Superconducting Niobium

We identify a major source of quantum decoherence in three-dimensional superconducting radio-frequency (SRF) resonators and two-dimensional transmon qubits composed of oxidized niobium: oxygen vacancies in the niobium pentoxide, which drive two-level system (TLS) losses. By probing the effect of sequential in situ vacuum-baking treatments on the rf performance of bulk Nb SRF resonators and on the oxide structure of a representative Nb sample using TOF SIMS, we find a nonmonotonic evolution of cavity quality factor Q0, which correlates with the interplay of Nb2O5 vacancy generation and oxide-thickness reduction. We localize this effect to the oxide itself and present the insignificant role of diffused interstitial oxygen in the underlying Nb by regrowing the oxide via wet oxidation, which reveals a mitigation of aggravated TLS losses. We hypothesize that such vacancies in the pentoxide serve as magnetic impurities and are a source of TLS-driven rf loss.

Bafia, Daniel P. [Fermilab]↗
DOE OSTI2020

The use of U3Si2/Al dispersion fuel for high power research reactors

In order to investigate the irradiation performance of U3Si2/Al dispersion fuel at relatively aggressive reactor conditions, compared to how this fuel is typically used in a research or test reactor, post irradiation examination was performed on two fuel plates that were irradiated at ~270 W/cm2 average surface heat flux and to a maximum local burnup greater than 8 × 1021 fissions/cm3 in the Advanced Test Reactor as part of the RERTR-8 experiment. As part of the non-destructive examinations that were performed on both fuel plates, detailed thickness measurements using a high-fidelity measurement bench were performed on one fuel plate and a segment of the second fuel plate. This paper provides the first reported results of such high-resolution thickness measurements for U3Si2/Al dispersion fuel plates, containing primarily the U3Si2 fuel phase, irradiated at such power levels to high burnup. For destructive examination using optical metallography, samples were generated from both irradiated plates. Localized regions of high swelling (characteristic of internal blistering) were observed on the surface of both fuel plates, suggesting that the performance limits had been reached for each plate. Destructive examinations showed that the fuel particles that are primarily U3Si2, which become amorphous during irradiation, in both plates contained relatively large fission gas bubbles with evidence of fission gas bubble interconnection.

Wachs, Daniel M.↗