SEARCH · Search NASA

Results for “aviation fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 433 records · Page 24

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Preferential concentration of certain elements in smaller aerosols emitted from aircraft engines

Aerosols from aircraft engines were collected with an eight-stage cascade sampler for a period of 24 h. The aerosol samples from each stage were analyzed for their elemental composition using the proton-induced X-ray emission (PIXE) technique. Seventeen elements (Si, P, S, Cl, K, Ca, Ti, V, Fe, Ni, Cu, Zn, Br, Sr, Nb, Sn, and Pb) were positively identified and quantitated at each stage. Six elements (S, Ca, Fe, Zn, Sn, and Pb) showed a fractional concentration increase with decreasing aerosol size. Similar, but less well-defined, trends were also observed for V and Ni. Silicon and chlorine, on the other hand, showed an opposite trend. Neutron-activation analysis of bulk aerosol samples collected every 2 h over the same period showed a correlation between concentration of Si, Ca, V, Ti, Zn, Br, and Sn and the density of air traffic at the airport. Analysis of the aviation-fuel samples by PIXE indicates that major fractions of Pb, Sn, Br, Zn, Ni, Fe, V, Ca, and S observed in these aerosol studies come from the aircraft engine exhaust.

Jolly, R. K.↗

NASA NTRS1978

Environmental effects on composites for aircraft

A number of ongoing, long-term environmental effects programs for composite materials are evaluated. The flight service experience was evaluated for 142 composite aircraft components after more than 5 years and 1 million successful component flight hours. Ground-based outdoor exposures of composite material coupons after 3 years of exposure at 5 sites have reached equilibrium levels of moisture pickup which are predictable. Solar ultraviolet-induced material loss is discussed for these same exposures. No significant degradation was observed in residual strength for either stressed or unstressed specimens, or for exposures to aviation fuels and fluids.

Pride, R. A.↗

NASA NTRS1978

Interim results of long-term environmental exposures of advanced composites for aircraft applications

Interim results from a number of ongoing, long-term environmental effects programs for composite materials are reported. The flight service experience is evaluated for 142 composite aircraft components after more than five years and one million successful component flight hours. Ground-based outdoor exposures of composite material coupons after 3 years of exposure at five sites have reached equilibrium levels of moisture pickup which are predictable. Solar ultraviolet-induced material loss is discussed for these same exposures. No significant degradation has been observed in residual strength for either stressed or unstressed specimens, or for exposures to aviation fuels and fluids.

Pride, R. A.↗

NASA NTRS1980

Some advantages of methane in an aircraft gas turbine

Because liquid methane may be obtained from existing natural gas sources or produced synthetically from a range of other hydrocarbon sources (coal, biomass, shale, organic waste), it is considered as an aviation fuel in a simplified cycle analysis of the performance of a turboprop engine intended for operation at Mach 0.8 and 10,688 m altitude. Performance comparisons are given for four cases in which the turbine cooling air is either not cooled or cooled to -111, -222, and -333 K, and the advantages and problems that may be expected from direct use of the cryogenic fuel in turbine cooling are discussed. It is shown that while (1) methane combustion characteristics are appreciably different from those of Jet A fuel and will require the development of different combustor designs, and (2) the safe integration of methane cryotanks into transport aircraft structures poses a major design problem, a highly fuel-efficient turboprop engine fueled by methane appears to be feasible.

Graham, R. W.↗

NASA NTRS1982

The NASA MERIT program - Developing new concepts for accurate flight planning

It is noted that the rising cost of aviation fuel has necessitated the development of a new approach to upper air forecasting for flight planning. It is shown that the spatial resolution of the present weather forecast models used in fully automated computer flight planning is an important accuracy-limiting factor, and it is proposed that man be put back into the system, although not in the way he has been used in the past. A new approach is proposed which uses the application of man-computer interactive display techniques to upper air forecasting to retain the fine scale features of the atmosphere inherent in the present data base in order to provide a more accurate and cost effective flight plan. It is pointed out that, as a result of NASA research, the hardware required for this approach already exists.

Steinberg, R.↗

NASA NTRS1982

A preliminary intercomparison between numerical upper wind forecasts and research aircraft measurements of jet streams

During the past several years, research on the structure of extra-tropical jet streams has been carried out with direct measurements with instrumented research aircraft from the National Center for Atmospheric Research (NCAR). These measurements have been used to describe the wind, temperature, turbulence and chemical characteristics of jet streams. A fundamental question is one of assessing the potential value of existing operational numerical forecast models for forecasting the meteorological conditions along commercial aviation flight routes so as to execute Minimum Flight Time tracks and thus obtain the maximum efficiency in aviation fuel consumption. As an initial attempt at resolving this question, the 12 hour forecast output from two models was expressed in terms of a common output format to ease their intercomparison. The chosen models were: (1) the Fine-Mesh Spectral hemispheric and (2) the Limited Area Fine Mesh (LFM) model.

Shapiro, M. A.↗

NASA NTRS1986

Development of LC-13C NMR

This study involves the development of C-13 nuclear resonance as an on-line detector for liquid chromatography (LC-C-13 NMR) for the chemical characterization of aviation fuels. The initial focus of this study was the development of a high sensitivity flow C-13 NMR probe. Since C-13 NMR sensitivity is of paramount concern, considerable effort during the first year was directed at new NMR probe designs. In particular, various toroid coil designs were examined. In addition, corresponding shim coils for correcting the main magnetic field (B sub 0) homogeneity were examined. Based on these initial probe design studies, an LC-C-13 NMR probe was built and flow C-13 NMR data was obtained for a limited number of samples.

Dorn, H. C.↗

NASA NTRS1996

Experimental Characterization of Gas Turbine Emissions at Simulated Flight Altitude Conditions

NASA's Atmospheric Effects of Aviation Project (AEAP) is developing a scientific basis for assessment of the atmospheric impact of subsonic and supersonic aviation. A primary goal is to assist assessments of United Nations scientific organizations and hence, consideration of emissions standards by the International Civil Aviation Organization (ICAO). Engine tests have been conducted at AEDC to fulfill the need of AEAP. The purpose of these tests is to obtain a comprehensive database to be used for supplying critical information to the atmospheric research community. It includes: (1) simulated sea-level-static test data as well as simulated altitude data; and (2) intrusive (extractive probe) data as well as non-intrusive (optical techniques) data. A commercial-type bypass engine with aviation fuel was used in this test series. The test matrix was set by parametrically selecting the temperature, pressure, and flow rate at sea-level-static and different altitudes to obtain a parametric set of data.

GAS TURBINES↗

NASA NTRS2004

An Apparatus for Monitoring the Health of Electrical Cables

As with most elements of infrastructure, electrical wiring is innocuous; usually hidden away and unnoticed until it fails. Failure of infrastructure, however, sometimes leads to serious health and safety hazards. Electrical wiring fails when the polymeric (usually rubber) insulation material that sheathes the conductor gets embrittled with age from exposure to pressure, temperature or radiation cycling or when the insulation gets removed by the chafing of wires against each other. Miles of such wiring can be found in typical aircraft, with significant lengths of the wiring immersed in aviation fuel - a recipe for an explosion if a spark were to occur. Diagnosing the health of wiring is thus an important aspect of monitoring the health of aging aircraft. Stress wave propagation through wiring affords a quick and non-invasive method for health monitoring. The extent to which a stress wave propagating through the cable core gets attenuated depends on the condition of the surrounding insulation. When the insulation is in good condition - supple and pliable, there is more damping or attenuation of the waveform. As the insulation gets embrittled and cracked, the attenuation is likely to reduce and the waveform of the propagating stress wave is likely to change. The monitoring of these changes provides a potential tool to evaluate wiring or cabling in service that is not accessible for visual inspection. This experiment has been designed for use in an introductory mechanical or materials engineering instrumentation lab. Initial setup (after procuring all the materials) should take the lab instructor about 4 hours. A single measurement can be initiated and saved to disk in less than 3 minutes, allowing for all the students in a typical lab section to take their own data rather than share a single set of data for the entire class.

Pai, Devdas M.↗

NASA NTRS2011

Research Of Airborne Precision Spacing to Improve Airport Arrival Operations

In September 2004, the European Organization for the Safety of Air Navigation (EUROCONTROL) and the United States Federal Aviation Administration (FAA) signed a Memorandum of Cooperation to mutually develop, modify, test, and evaluate systems, procedures, facilities, and devices to meet the need for safe and efficient air navigation and air traffic control in the future. In the United States and Europe, these efforts are defined within the architectures of the Next Generation Air Transportation System (NextGen) Program and Single European Sky Air Traffic Management Research (SESAR) Program respectively. Both programs have identified Airborne Spacing as a critical component, with Automatic Dependent Surveillance Broadcast (ADS-B) as a key enabler. Increased interest in reducing airport community noise and the escalating cost of aviation fuel has led to the use of Continuous Descent Arrival (CDA) procedures to reduce noise, emissions, and fuel usage compared to current procedures. To provide these operational enhancements, arrival flight paths into terminal areas are planned around continuous vertical descents that are closer to an optimum trajectory than those in use today. The profiles are designed to be near-idle descents from cruise altitude to the Final Approach Fix (FAF) and are typically without any level segments. By staying higher and faster than conventional arrivals, CDAs also save flight time for the aircraft operator. The drawback is that the variation of optimized trajectories for different types and weights of aircraft requires the Air Traffic Controller to provide more airspace around an aircraft on a CDA than on a conventional arrival procedure. This additional space decreases the throughput rate of the destination airport. Airborne self-spacing concepts have been developed to increase the throughput at high-demand airports by managing the inter-arrival spacing to be more precise and consistent using on-board guidance. It has been proposed that the additional space needed around an aircraft performing a CDA could be reduced or eliminated when using airborne spacing techniques.

Barmore, Bryan E.↗

NASA NTRS2015

An Overview of 2014 SBIR Phase 1 and Phase 2 Air-Breathing Propulsion

NASA's Small Business Innovation Research (SBIR) program focuses on technological innovation by investing in development of innovative concepts and technologies to help NASA mission directorates address critical research needs for Agency programs. This report highlights nine of the innovative SBIR 2014 Phase I and Phase II projects that emphasize one of NASA Glenn Research Center's six core competencies-Air-Breathing Propulsion. The technologies cover a wide spectrum of applications such as development of X-ray computed tomography (CT) imaging method for the measurement of complex 3D ice shapes, phased array techniques for low signal-to-noise ratio wind tunnels, compact kinetic mechanisms for petroleum-derived and alternative aviation fuels, and hybrid electric propulsion systems for a multirotor aircraft. Each featured technology describes an innovation, technical objective, and highlights NASA commercial and industrial applications. This report provides as an opportunity for NASA engineers, researchers, and program managers to learn how NASA SBIR technologies could help their programs and projects, and lead to collaborations and partnerships between the small SBIR companies and NASA that would benefit both.

phased array technique for wind tunnels↗

NASA NTRS2013

Evaluation of the Terminal Area Precision Scheduling and Spacing System for Performance-Based Navigation Arrivals

The growth of global demand for air transportation has put increasing strain on the nation's air traffic management system. To relieve this strain, the International Civil Aviation Organization has urged all nations to adopt Performance-Based Navigation (PBN), which can help to reduce air traffic congestion, decrease aviation fuel consumption, and protect the environment. NASA has developed a Terminal Area Precision Scheduling and Spacing (TAPSS) system that can support increased use of PBN during periods of high traffic, while supporting fuel-efficient, continuous descent approaches. In the original development of this system, arrival aircraft are assigned fuel-efficient Area Navigation (RNAV) Standard Terminal Arrival Routes before their initial descent from cruise, with routing defined to a specific runway. The system also determines precise schedules for these aircraft that facilitate continuous descent through the assigned routes. To meet these schedules, controllers are given a set of advisory tools to precisely control aircraft. The TAPSS system has been evaluated in a series of human-in-the-loop (HITL) air traffic simulations during 2010 and 2011. Results indicated increased airport arrival throughput up to 10 over current operations, and maintained fuel-efficient aircraft decent profiles from the initial descent to landing with reduced controller workload. This paper focuses on results from a joint NASA and FAA HITL simulation conducted in 2012. Due to the FAA rollout of the advance terminal area PBN procedures at mid-sized airports first, the TAPSS system was modified to manage arrival aircraft as they entered Terminal Radar Approach Control (TRACON). Dallas-Love Field airport (DAL) was selected by the FAA as a representative mid-sized airport within a constrained TRACON airspace due to the close proximity of a major airport, in this case Dallas-Ft Worth International Airport, one of the busiest in the world. To address this constraint, RNAV routes and Required Navigation Performance with the particular capability known as Radius-to-Fix (RNP-RF) approaches to a short final were used. The purpose of this simulation was to get feedback on how current operations could benefit with the TAPSS system and also to evaluate the efficacy of the advisory tools to support the broader use of PBN in the US National Airspace System. For this NASA-FAA joint experiment, an Air Traffic Control laboratory at NASA Ames was arranged to simulate arrivals into DAL in Instrument Meteorological Conditions utilizing parallel dependent approaches, with two feeder positions that handed off traffic to one final position. Four FAA controllers participated, alternately covering these three positions. All participants were Full-Performance Level terminal controllers and members of the National Air Traffic Controllers Association. During the simulation, PBN arrival operations were compared and contrasted in three conditions. They were the Baseline, where none of the TAPSS systems TRACON controller decision support advisories were provided, the Limited Advisories, reflecting the existing but dormant capabilities of the current terminal automation equipment with providing a subset of the TAPSS systems advisories; numerical delay, landing sequence, and runway assignment information, and the Full Advisories, with providing the following in addition to the ones in the Limited condition; trajectory slot markers, timelines of estimated times of arrivals and sched

Performance based navigation↗

NASA NTRS2018

NASA Emissions Research Overview

NASA Aeronautics is advancing a variety of technologies toward the objective of reducing aviation fuel burn and emissions. Specifically, the Advanced Air Transport Technology Project under the Advanced Air Vehicles Program is investing in technologies such as small core engines, fuel-flexible combustors, and electrified aircraft propulsion, all of which offer potential for reduced fleet fuel usage and harmful emissions. This presentation will provide a brief overview of these technical approaches as well as a NASA Aeronautics budget outlook.

Heidmann, Jim↗

NASA NTRSDate not supplied

NASA Sustainable Flight National Partnership Panel

The National Aeronautics and Space Administration (NASA) Aeronautics Mission Directorate (ARMD) Hybrid Thermally Efficient Core (HyTEC) Project within the Advanced Air Vehicles Program (AAVP) is focused on accelerating the development of small-core turbofan engine technologies to advance the next entry into service (EIS) single-aisle aircraft having 25,000-35,000 lb. thrust class engines. The goal is to accelerate the development of key engine technologies with improvements in efficiency, durability, performance, and hybridization in order to meet the next EIS single-aisle aircraft expected in the 2030s. The HyTEC Project technology portfolio includes High Pressure Compressor, High Pressure Turbine, Advanced Materials, Hybrid Electric and Compact Combustor (includes operation with Sustainable Aviation Fuels (SAF)). The individual technologies were industry partner proposed and defined where HyTEC selected technologies to cost share with the industry partner. The first phase of the project has matured some and continues to mature numerous technologies to a Technology Readiness Level (TRL) 4-5, which will then be integrated into an advanced small core demonstration. The results of completed efforts have been successful, and projections toward project performance metrics of all Phase 1 technologies indicates significant progress toward meeting the requirements. The core demonstration will integrate many of these technologies into a large-scale ground demonstration that will take them to TRL 6 and enable industry to transition the technologies into the next single-aisle engine architecture. The demonstration goal is to meet the project performance metrics that signify a compact engine core with substantial efficiency and durability improvements over a year 2020 baseline. The core demonstration has been awarded with a cost-share partnership and will take place by the end of 2028.

Tony Nerone↗

DOE OSTI2023

Task 2.3: Continuous Counter-Current Chromatography

This task in the Separations Consortium focuses on the development of counter-current chromatography (CCC), which is an advanced liquid-liquid chromatography method. Today, CCC is primarily practiced in batch mode operation, but continuous operation will be required for at-scale deployment in a biorefinery setting. In this task, we are developing a continuous CCC process in collaboration with a company that builds CCC units. This work will be demonstrated on the biorefining challenge of lignin valorization. Specifically, we demonstrate use of continuous CCC for both monomer-monomer and monomer-oligomer separations in multiple lignin streams of relevance to the biorefining industry. Breakthroughs in this area would be useful for BETO goals in both sustainable aviation fuel and biochemicals production, including directly contributing to BETO's 2030 lignin valorization goal. Our approach includes developing new computational modeling approaches to optimize both batch and continuous CCC processes, experimental work to determine optimal solvent systems for multiple lignin streams sourced from BETO-funded projects and industrial collaborators, and techno-economic analysis and life cycle assessment to identify the most impactful areas to ultimately enable this approach in the biorefinery. This task overall will enable high-resolution, multi-component, continuous separations at scale, demonstrated on a grand challenge biorefining problem.

BIOMASS FUELS↗

DOE OSTI2023

Direct Conversion of Delignified Biomass into Non-Volatile Products Using Thermophilic Bacteria

Butyric acid (BA) can be used as a platform intermediate for diesel and sustainable aviation fuels (SAFs) as well as a precursor for diverse commodity chemicals for the production of polymers, fibers, solvents, and preservatives. This work presents a co-culture-based bioprocess for the production of BA from corn stover by two thermophilic bacteria, Clostridium thermocellum, a well-known efficient degrader of insoluble and oligomeric cellulosic substrates, and Clostridium thermobutyricum, a highly efficient BA producer from monomeric sugars. First, we tested the capability of C. thermocellum to deconstruct three different biomass streams from the NREL pilot plant pretreatment process -raw, deacetylated, and deacetylated and mechanically refined corn stover (DMR)-, and up to 82% solids deconstruction and 91% carbohydrate utilization were obtained when using DMR solids. Then, the sugar utilization and by-product formation capabilities on various substrates by C. thermobutyricum were compared to evaluate its potential as a co-culture partner for C. thermocellum. Model carbon sources -glucose and xylose- were compared to a mixture of substrates present in soluble DMR hydrolysate streams, and the highest cell density as well as the maximum BA titer (8.3 g/L) were observed on DMR hydrolysate. Finally, clostridial co-cultivations on DMR solids were performed to investigate the inoculation time for both organisms that enhances BA production; while C. thermocellum was always inoculated at the beginning of the cultivation, C. thermobutyricum was inoculated at 0, 36, or 72h. It was found that BA production begins immediately upon inoculation of C. thermobutyricum regardless of the inoculation time. However, higher solids deconstruction and carbohydrate utilization results (83.7 and 95.6%, respectively) were obtained when both organisms were inoculated at the beginning of the fermentation. Under those conditions, up to 2.6 g/L of BA were obtained from DMR solids after 120h of cultivation. This work provides relevant information for the sustainable production of BA using thermophilic bacteria.

bacterial co-culture↗

DOE OSTI2023

Using Life Cycle Assessment to Inform CBI Research Priorities

Life cycle assessment (LCA) is used within the Center for Bioenergy Innovation (CBI) to provide information about how feedstock agricultural practices, supply chain logistics, biorefinery operating parameters, and the slate of biofuels and products contribute to environmental impacts, and how CBI's research priorities can result in less impactful biofuel supply chains. This poster provides an overview of the LCA methodology used within CBI and focuses on data needs in general and from other CBI teams. Assumptions and simplifications within biofuel LCA studies are reviewed, including options for modeling multi-functional processes. Calculation details for life cycle environmental impacts used within CBI - global warming potential, cumulative energy demand, and the Available Water Remaining indicator - are presented, along with a discussion of carbon intensity as an alternative metric for evaluating sustainable aviation fuel and other biofuels. The process of interpreting impact results to guide research priorities is discussed, with examples drawn from CBI's upcoming manuscript on switchgrass yield and cell wall composition.

bioenergy↗

DOE OSTI2023

Butyric Acid Production from Delignified Corn Stover Using Thermophilic Bacterial Co-Cultures

Butyric acid (BA) is a valuable platform chemical in the food and pharmaceutical industries, and it is also a potential precursor for the production of biobutanol and sustainable aviation fuels (SAFs). BA is mainly synthesized from petroleum; thus, cost-effective, and sustainable alternatives for its production are attracting the interest of several sectors. The present work proposes a solids-to-acids bioprocess to produce BA from corn stover utilizing a co-culture that consists of two thermophilic bacteria, Clostridium thermocellum, a well-known efficient degrader of insoluble and oligomeric cellulosic substrates, and Clostridium thermobutyricum, a highly efficient BA producer from monomeric sugars. After initial proof of concept experiments, a series of optimization studies were carried out to evaluate the process limits of this co-culture. First, the co-cultivation of both microorganisms at different inoculum sizes in deacetylated and mechanically refined corn stover (DMR) was evaluated. No significant differences were found on the solids deconstruction and carbohydrates utilization among all the treatments. In addition, BA production was similar under all conditions, ranging between 2.1 and 2.4 g/L. Next, the deconstruction, and BA production capabilities of the co-culture at increased DMR solids contents (3, 4.5, and 6% (w/v)) were tested. Although no difference was observed in the solids deconstruction and carbohydrates utilization among treatments, BA production increased concomitantly to solids loading; the maximum values observed were 2.8, 3.6, and 6.2 g/L in the 3, 4.5, and 6% treatments, respectively. In fact, BA production did not reach its absolute maximum in the 6% treatment after 160 h of fermentation. Lastly, a fed-batch experiment was performed to investigate the co-culture capabilities and possible system constraints to achieve higher BA titers. Data on substrate modifications and product formation as well as on the growth of each microorganism will be shown. Results from this work demonstrate a promising bioprocess approach for the production of BA from lignocellulosic biomass using a thermophilic bacterial co-culture.

bacteria↗