SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Turbojet engine characteristics, control systems, thrust augmentation, and inlet design studies for supersonic flight propulsion
Method of comparing inlet performance and weight compromises for supersonic transport
Force and pressure-recovery characteristics of a nacelle-type conical-spike inlet with a fixed-area bypass located in the top or bottom of the diffuser are presented for flight Mach numbers of 1.6, 1.8, and 2.0 for angles of attack from 0 degrees to 9 degrees. Top or bottom location of the bypass did not have significant effects on diffuser pressure-recovery, bypass mass-flow ratio, or drag coefficient over the range of angles of attack, flight Mach numbers, and stable engine mass-flow ratios investigated. A larger stable subcritical operating range was obtained with the bypass on the bottom at angles of attack from 3 degrees to 9 degrees at a flight Mach number of 2.0. At a flight Mach number of 2.0, the discharge of 14 percent of the critical mass flow of the inlet by means of a bypass increased the drag only one-fifth of the additive drag that would result for equivalent spillage behind an inlet normal shock without significant reductions in diffuser pressure recovery.
The combustion performance, and particularly the phenomenon of altitude operational limits, was studied by operating the annular combustor of a turbojet engine over a range of conditions of air flow, inlet pressure, inlet temperature, and fuel flow. Information was obtained on the combustion efficiencies, the effect on combustion of inlet variables, the altitude operational limits with two different fuels, the pressure losses in the combustor, the temperature and velocity profiles at the combustor outlet, the extent of afterburning, the fuel-injection characteristics, and the condition of the combustor basket.
Axisymmetric double cone external compression inlet in transonic range - drag components at detached shock conditions
Low cowl drag, external compression inlet with subsonic dump diffuser for high Mach number application
Turbofan engine used for evaluating air jets as steady state inlet flow distortion device
A study of a 20 degree and a 25 degree half-angle high mass-flow ratio conical supersonic inlet was made on a 16-inch ram jet in the 8- by 6-foot supersonic tunnel. A greater range of stable subcritical operation was obtained with the low mass-flow ratio inlets; a greater range was obtained with the 25 degree than with the 20 degree half-angle low mass-flow ratio inlet. The high mass-flow ratio inlet had the least drag.
Effect of variation of combustion chamber length and inlet temperature on low pressure-loss sea level afterburner
Supersonic wind tunnel test of underslung scoop inlet on body of revolution
Explore the source record for details and available documents.
Performance characteristics of underslung vertical wedge inlet with porous suction at Mach numbers of 0.63 and 1.5 to 2.0
Axisymmetric external compression double cone inlet - mach 3 to 0.8 - pressure recovery, mass flow ratio, cowl pressure and additive drag
Performance of internal contraction, axisymmetric inlet with isentropic compression surfaces on cowl and centerbody at Mach 2.0 to 2.7
Performance of four experimentally investigated axially symmetric spike-type nose inlets is compared on basis of ram-jet-engine aircraft range and operational problems. At design conditions, calculated peak engine efficiencies varied 25 percent from the highest value which indicates importance of inlet design. Calculations for a typical supersonic aircraft indicate possible increase in range if engine is flown at moderate angle of attack and result in engine lift utilized. For engines with fixed exhaust nozzle, propulsive thrust increases with increasing heat addition in subcritical flow region in spite of increasing additive drag. For the perforated inlet there is a range of increasing total-temperature ratios in subcritical flow region that does not yield an increase in propulsive thrust. Effects of inlet characteristics on speed stability of a typical aircraft for three types of fuel control is discussed.
Changing the flow rate of reactants being injected into a rotating detonation combustor (RDC) results in interesting behavior of the system. Prior studies have found that an increase in mass flow rate gradually increases the detonation wave speed before splitting the wave into multiple fronts. Here, the focus of this study is in understanding the physics of such behavior through a combination of experiments and numerical simulations. For this purpose, the axial air inlet-based RDC geometry is used. In the experiments, the wave velocity increased similar to prior studies. Corresponding full-scale simulations show that increase in mass flow rate by increasing pressure of the feed plenums shortens the recovery time of the injectors. This causes a more uniform fuel–air mixture to form prior to the arrival of the detonation wave. As a result, a more ideal detonation is observed, which leads to an increased wave velocity. Details of the detonation structure and variation with mass flow rate are analyzed. The presence and variation of the different deflagration zones in such non-premixed RDCs are also discussed.
An experimental investigation was made at Mach number 1.90 of the performance of a series of perforated convergent-divergent supersonic diffusers operating with initial boundary layer, which was induced and controlled by lengths of cylindrical inlets affixed to the diffusers. Supercritical mass-flow and peak total-pressure recoveries were decreased slightly by use of the longest inlets (4 inlet diameters in length). Combinations of cylindrical inlets, perforated diffusers, and subsonic diffuser were evaluated as simulated wind tunnels having second throats. Comparisons with noncontracted configurations of similar scale indicated conservatively computed power reductions of 25 percent.
A study was conducted to determine the effect of chord size on air cooled turbine blades. In the preliminary design phase, eight turbine blade cooling configurations in 0.75-in., 1.0-in., and 1.5-in. chord sizes were analyzed to determine the maximum turbine inlet temperature capabilities. A pin fin convection cooled configuration and a film-impingement cooled configuration were selected for a final design analysis in which the maximum turbine inlet temperature was determined as a function of the cooling air inlet temperature and the turbine inlet total pressure for each of the three chord sizes. The cooling air flow requirements were also determined for a varying cooling air inlet temperature with a constant turbine inlet temperature. It was determined that allowable turbine inlet temperature increases with increasing chord for the convection cooled and transpiration cooled designs, however, the film-convection cooled designs did not have a significant change in turbine inlet temperature with chord.