Search NASA⌕ Search

SEARCH · Search NASA

Results for “transient testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Applications of Similarity Analysis of Reactivity-initiated Accident Experiments in TREAT

Experimental testing capabilities have been created to perform reactivity-initiated accident experiments in the Transient Reactor Test Facility for fuel safety testing of Accident Tolerant Fuel concepts and to extend the burnup limits for our current light water reactor fuel designs. Completely prototypic test conditions are not possible and compromises naturally have to be made. To date, the representativity of the small scale safety testing to a similar event in a commercial reactor is made by comparing a few specific phenomena of interest. The goal of this work is to apply similarity analysis as another metric to judge the representativity of in-pile safety tests to full-scaled accident scenario.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The performance of cable braids and terminations to lightning induced transients

The latest specification detailing the test waveforms for indirect lightning transients as applied to aircraft wiring systems specify very high voltages and currents. Although considerable data exists for measuring cable screen leakage using such methods as surface transfer impedance and bulk cable injection, there is little data on the likely core transient level that is likely to be induced from these threats. In particular, the new Waveform 5 at very high current levels (10 kA) is reputed to cause severe cable damage. A range of representative cables were made with various screen termination techniques and screening levels. These were tested first to determine their relative screening performance and then they were subjected to lightning transient testing to all the specified waveforms. Core voltages were measured for each test. Tests were also performed on bundles with fewer wires to determine the failure criteria with Waveform 5 and these tests also include flat conductor cables. The test showed that correctly terminated cable bundles performed well in all the tests and would provide a high level of protection to the electronic systems. The use of overbraides, provided the individual screens are well terminated, appears to be unnecessary.

Crofts, David↗

Development of Hydrologic Characterization Technology of Fault Zones

Through an extensive literature survey we find that there is very limited amount of work on fault zone hydrology, particularly in the field using borehole testing. The common elements of a fault include a core, and damage zones. The core usually acts as a barrier to the flow across it, whereas the damage zone controls the flow either parallel to the strike or dip of a fault. In most of cases the damage zone isthe one that is controlling the flow in the fault zone and the surroundings. The permeability of damage zone is in the range of two to three orders of magnitude higher than the protolith. The fault core can have permeability up to seven orders of magnitude lower than the damage zone. The fault types (normal, reverse, and strike-slip) by themselves do not appear to be a clear classifier of the hydrology of fault zones. However, there still remains a possibility that other additional geologic attributes and scaling relationships can be used to predict or bracket the range of hydrologic behavior of fault zones. AMT (Audio frequency Magneto Telluric) and seismic reflection techniques are often used to locate faults. Geochemical signatures and temperature distributions are often used to identify flow domains and/or directions. ALSM (Airborne Laser Swath Mapping) or LIDAR (Light Detection and Ranging) method may prove to be a powerful tool for identifying lineaments in place of the traditional photogrammetry. Nonetheless not much work has been done to characterize the hydrologic properties of faults by directly testing them using pump tests. There are some uncertainties involved in analyzing pressure transients of pump tests: both low permeability and high permeability faults exhibit similar pressure responses. A physically based conceptual and numerical model is presented for simulating fluid and heat flow and solute transport through fractured fault zones using a multiple-continuum medium approach. Data from the Horonobe URL site are analyzed to demonstrate the proposed approach and to examine the flow direction and magnitude on both sides of a suspected fault. We describe a strategy for effective characterization of fault zone hydrology. We recommend conducting a long term pump test followed by a long term buildup test. We do not recommend isolating the borehole into too many intervals. We do recommend ensuring durability and redundancy for long term monitoring.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

FUEL PERFORMANCE SIMULATION OF HIGH BURNUP FUELS IN PLANNED INTEGRAL DESIGN BASIS ACCIDENT EXPERIMENTS

High burnup (HBu) fuel rods from the Byron Nuclear Generating Station (BNGS) were recently received at Idaho National Laboratory (INL) to support a variety of planned Nuclear Energy fuel cycle R&D objectives ranging from fuel performance, fuel recycle, and spent fuel research topics. Among these R&D activities, these fuel rods will be the subjects of multiple in-pile experiment programs at the Transient Reactor Test (TREAT) facility as well as detailed characterization and testing in the hot cells at INL and Oak Ridge National Laboratory (ORNL). TREAT RIA experiments are planned for the Nuclear Energy Agency Framework for Irradiation Experiments (FIDES) Joint Experimental Program called High burnup Experiments in Reactivity Initiated Accident (HERA) program. TREAT and ORNL-furnace LOCA experiments are part of the Department of Energy (DOE) Advanced Fuels Campaign (AFC) program U.S. consensus LOCA test plan, and the in-pile experiments have also been proposed in a FIDES project called Loss of Coolant-High Burnup (LOC-HBu). The results of these test programs will provide crucial data about safety performance enabling extended licensable burnup limits for these fuels. The purpose of this paper is to document fuel performance computational simulations of the BNGS fuel using the Bison code. The detailed assessments include (1) the irradiation history of the fuel to provide prediction of as-run fuel conditions and (2) extending the irradiated fuel conditions into the as-designed experiment conditions for the HERA-HBu RIA experiments and for the LOC-HBu LOCA experiments. The results of these assessments will inform post-irradiation examinations (PIE) of the BNGS parent rods and detailed final design of the planned experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FUEL PERFORMANCE SIMULATION OF HIGH BURNUP FUELS IN PLANNED INTEGRAL DESIGN BASIS ACCIDENT EXPERIMENTS

High burnup (HBu) fuel rods from the Byron Nuclear Generating Station (BNGS) were recently received at Idaho National Laboratory (INL) to support a variety of planned Nuclear Energy fuel cycle R&D objectives ranging from fuel performance, fuel recycle, and spent fuel research topics. Among these R&D activities, these fuel rods will be the subjects of multiple in-pile experiment programs at the Transient Reactor Test (TREAT) facility as well as detailed characterization and testing in the hot cells at INL and Oak Ridge National Laboratory (ORNL). TREAT RIA experiments are planned for the Nuclear Energy Agency Framework for Irradiation Experiments (FIDES) Joint Experimental Program called High burnup Experiments in Reactivity Initiated Accident (HERA) program. TREAT and ORNL-furnace LOCA experiments are part of the Department of Energy (DOE) Advanced Fuels Campaign (AFC) program U.S. consensus LOCA test plan, and the in-pile experiments have also been proposed in a FIDES project called Loss of Coolant-High Burnup (LOC-HBu). The results of these test programs will provide crucial data about safety performance enabling extended licensable burnup limits for these fuels. The purpose of this paper is to document fuel performance computational simulations of the BNGS fuel using the Bison code. The detailed assessments include (1) the irradiation history of the fuel to provide prediction of as-run fuel conditions and (2) extending the irradiated fuel conditions into the as-designed experiment conditions for the HERA-HBu RIA experiments and for the LOC-HBu LOCA experiments. The results of these assessments will inform post-irradiation examinations (PIE) of the BNGS parent rods and detailed final design of the planned experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Object-oriented approach for gas turbine engine simulation

An object-oriented gas turbine engine simulation program was developed. This program is a prototype for a more complete, commercial grade engine performance program now being proposed as part of the Numerical Propulsion System Simulator (NPSS). This report discusses architectural issues of this complex software system and the lessons learned from developing the prototype code. The prototype code is a fully functional, general purpose engine simulation program, however, only the component models necessary to model a transient compressor test rig have been written. The production system will be capable of steady state and transient modeling of almost any turbine engine configuration. Chief among the architectural considerations for this code was the framework in which the various software modules will interact. These modules include the equation solver, simulation code, data model, event handler, and user interface. Also documented in this report is the component based design of the simulation module and the inter-component communication paradigm. Object class hierarchies for some of the code modules are given.

Curlett, Brian P.↗

Sensitivity Analysis of Transient Critical Heat Flux by RIA Under High-Pressure Flow Boiling Conditions in TRTL

A reactivity-initiated accident (RIA) is a design-basis accident under which critical heat flux (CHF) is likely to be exceeded. The operational margin for RIAs is currently determined using steady-state CHF lookup tables, which provide conservative estimates relative to transient CHF phenomena. The Transient Reactor Test Loop (TRTL) facility at Oregon State University is capable of performing out-of-pile rapid heating experiments representative of a RIA at conditions representative of a pressurized water reactor (PWR). Here, to further our understanding of and ability to predict transient CHF under PWR conditions, we performed a sensitivity analysis on a RELAP5-3D model of the TRTL facility coupled to the RAVEN code framework to define a proposed experimental test matrix to be performed at the TRTL facility. We then implemented a flow boiling CHF correlation into RELAP5-3D and performed a secondary sensitivity analysis inspecting the impact of the built-in RELAP5-3D CHF and heat transfer multipliers on both the prediction of CHF and key safety parameters, such as peak cladding temperature and heat flux. The results show that the multiplier with the highest influence toward the prediction of CHF occurrence and the safety parameters is the transient CHF multiplier. Operational performance envelopes have been developed for each of the test matrix cases and will be used for validation once the experiments are performed. The TRTL facility is currently performing shakedown testing to verify system performance prior to proceeding with the experimental campaign. Restart testing results include pump curve restart testing, pressure tests, and heater rod thermocouple transients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Recrystallization driven softening and heating rate dependencies of FeCrAl nuclear fuel cladding during accident transients

A refined understanding of FeCrAl cladding behavior during rapid transients is critical for its potential deployment in light-water reactors. Current assessments focus on transient burst testing metrics such as balloon geometry, burst temperature, and hoop stress, often used as proxies for simpler conventional tensile properties. However, directly correlating isothermal tensile and creep data with accident transient scenarios remains a challenge, although it is essential for high fidelity model development. Recent modeling based on tensile tests up to 800 °C, conducted with both immediate loading and a 10-minute soak, showed that immediate loading better predicts experimental burst temperatures, indicating a thermal softening effect. Building upon this observation, the current study connects transient performance, microstructural evolution, and high-temperature tensile properties by leveraging results from C26M claddings burst tests performed at heating rates of 1–50 °C/s and hoop stresses from 25 to 100 MPa. At 25 MPa, rupture temperatures varied by only 6 °C, but at 100 MPa, the difference reached 116 °C, with faster heating yielding higher burst temperatures. Microstructural analysis identified recrystallization as the primary cause of heating rate-dependent softening, eliminating prior cold-working. In-situ thermomechanical data linked ballooning onset to localized instabilities, similar to ultimate tensile strength behavior in conventional tensile tests. High heating rates correlated with immediate loading tensile data, while lower rates matched soaked data. Furthermore, by linking burst performance to microstructural evolution and tensile properties, this work provides a foundation for more accurate modeling of FeCrAl claddings and potentially other Fe-based materials under accident conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Lifetime Reliability Prediction of Ceramic Structures Under Transient Thermomechanical Loads

An analytical methodology is developed to predict the probability of survival (reliability) of ceramic components subjected to harsh thermomechanical loads that can vary with time (transient reliability analysis). This capability enables more accurate prediction of ceramic component integrity against fracture in situations such as turbine startup and shutdown, operational vibrations, atmospheric reentry, or other rapid heating or cooling situations (thermal shock). The transient reliability analysis methodology developed herein incorporates the following features: fast-fracture transient analysis (reliability analysis without slow crack growth, SCG); transient analysis with SCG (reliability analysis with time-dependent damage due to SCG); a computationally efficient algorithm to compute the reliability for components subjected to repeated transient loading (block loading); cyclic fatigue modeling using a combined SCG and Walker fatigue law; proof testing for transient loads; and Weibull and fatigue parameters that are allowed to vary with temperature or time. Component-to-component variation in strength (stochastic strength response) is accounted for with the Weibull distribution, and either the principle of independent action or the Batdorf theory is used to predict the effect of multiaxial stresses on reliability. The reliability analysis can be performed either as a function of the component surface (for surface-distributed flaws) or component volume (for volume-distributed flaws). The transient reliability analysis capability has been added to the NASA CARES/ Life (Ceramic Analysis and Reliability Evaluation of Structures/Life) code. CARES/Life was also updated to interface with commercially available finite element analysis software, such as ANSYS, when used to model the effects of transient load histories. Examples are provided to demonstrate the features of the methodology as implemented in the CARES/Life program.

Nemeth, Noel N.↗

Gearbox Reliability Collaborative Update (Presentation)

Understand and isolate sources of gearbox failures; Improve understanding of internal loads and response; Normal operation and transients; Improve analysis tools to accurately simulate response; Improve ability to reproduce field response in dyno testing; Evaluate how CM augments design and O&M.

17 WIND ENERGY↗

Trends in shuttle entry heating from the correction of flight test maneuvers

A new technique was developed to systematically expand the aerothermodynamic envelope of the Space Shuttle Protection System (TPS). The technique required transient flight test maneuvers which were performed on the second, fourth, and fifth Shuttle reentries. Kalman filtering and parameter estimation were used for the reduction of embedded thermocouple data to obtain best estimates of aerothermal parameters. Difficulties in reducing the data were overcome or minimized. Thermal parameters were estimated to minimize uncertainties, and heating rate parameters were estimated to correlate with angle of attack, sideslip, deflection angle, and Reynolds number changes. Heating trends from the maneuvers allow for rapid and safe envelope expansion needed for future missions, except for some local areas.

Hodge, J. K.↗

Select Transient Metallic Fuel Bison Benchmarks

To explore the current capabilities of Bison with respect to transient metallic fuel modeling, four transient experiments are compared with their respective Bison model. The four experiments are the OPT-1 experiment of the Experimental Breeder Reactor II~(EBR-II) and the M5, M6, and M7 experiments of the Transient Reactor Test facility (TREAT). Each benchmark is a 2D-RZ geometry of a single pin employing coupled multiphysics. Bison models of the benchmark agree well and illustrate areas needing development. The areas of suggested development deal with better material models, better coolant channel module for transients, proper treatment of material melting, improved feedback with failure models, and an ability to set initial conditions from post irradiation examination (PIE) data. Two Fast Flux Test Facility (FFTF) pins are also modeled with M7 transient conditions to illustrate Bison being applied to investigate potential experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TREAT Modeling and Simulation Strategy

This report summarizes a four-phase process used to describe the strategy in developing modeling and simulation software for the Transient Reactor Test Facility. The four phases of this research and development task are identified as (1) full core transient calculations with feedback, (2) experiment modeling, (3) full core plus experiment simulation and (4) quality assurance. The document describes the four phases, the relationship between these research phases, and anticipated needs within each phase.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Numerical Modeling of Helium Pressurization System of Propulsion Test Article (PTA)

A transient model of the Propulsion Test Article (PTA) Helium Pressurization System was developed using the Generalized Fluid System Simulation Program (GFSSP). The model included feed lines from the facility interface to the engine purge interface and Liquid Oxygen (LOX) and Rocket Propellant 1 (RP-1) tanks, the propellant tanks themselves including ullage space and propellant feed lines to their respective pump interfaces. GFSSP's capability was extended to model a control valve to maintain ullage pressure within a specified limit and pressurization processes such as heat transfer between ullage gas, propellant and the tank wall. The purpose of the model is to predict the flow system characteristics in the entire pressurization system during 80 seconds of lower feed system priming, 420 seconds of fuel and LOX pump priming and 150 seconds of engine firing. Subsequent to the work presented here, the PTA model has been updated to include the LOX and RP-1 pumps, while the pressurization option itself has been modified to include the effects of mass transfer. This updated model will be compared with PTA test data as it becomes available.

Steadman, Todd↗

Evaluation of oxygenation in the surface layers of biological tissues based on diffuse optical spectroscopy with automated calibration of measurements

To assess the oxygen saturation (oxygenation) in the surface layers of biological tissues (at a depth of 4 mm), a compact system based on diffuse optical spectroscopy (DOS) with reflective measurement geometry in the wavelength range of 520 – 590 nm is proposed. The experimental DOS device is based on a broadband LED source of probe radiation and a spectrometer using a fibre-optic radiation delivery system. To calculate the oxygenation, an original method is proposed based on measuring the intensity of scattered light at four different locations of the source and receiver on the surface of the object under study (four-measurement method). The developed method allows for the device hardware parameters (optical contact with the tissue, transient characteristics of the radiation delivery system) and does not require any additional calibration measurements. The results of testing the DOS system using the four-measurement method for monitoring the oxygen saturation of tissues during the artificial occlusion of the blood vessels agree with the published data of other research teams. (paper)

60 APPLIED LIFE SCIENCES↗

NWTC Controllable Grid Interface (Fact Sheet)

NREL's Controllable Grid Interface tests wind turbines off-line from the grid, verifies compliance with standards, and provides grid operators with the performance information they need for a faction of the time and cost it would take to test the turbine in the field.

17 WIND ENERGY↗

Stochastic joint inversion of hydrogeophysical data for salt tracer test monitoring and hydraulic conductivity imaging

The assessment of hydraulic conductivity of heterogeneous aquifers is a difficult task using traditional hydrogeological methods (e.g., steady state or transient pumping tests) due to their low spatial resolution. Geophysical measurements performed at the ground surface and in boreholes provide additional information for increasing the resolution and accuracy of the inverted hydraulic conductivity field. We used a stochastic joint inversion of Direct Current (DC) resistivity and Self-Potential (SP) data plus in situ measurement of the salinity in a downstream well during a synthetic salt tracer experiment to reconstruct the hydraulic conductivity field between two wells. The pilot point parameterization was used to avoid over-parameterization of the inverse problem. Bounds on the model parameters were used to promote a consistent Markov chain Monte Carlo sampling of the model parameters. To evaluate the effectiveness of the joint inversion process, we compared 8 cases in which the geophysical data are coupled or not to the in situ sampling of the salinity to map the hydraulic conductivity. We first tested the effectiveness of the inversion of each type of data alone (concentration sampling, self-potential, and DC resistivity), and then we combined the data two by two. We finally combined all the data together to show the value of each type of geophysical data in the joint inversion process because of their different sensitivity map. We also investigated a case in which the data were contaminated with noise and the variogram unknown and inverted stochastically. The results of the inversion revealed that incorporating the self-potential data improves the estimate of hydraulic conductivity field especially when the self-potential data were combined to the salt concentration measurement in the second well or to the time-lapse cross-well electrical resistivity data. Various tests were also performed to quantify the uncertainty in the inverted hydraulic conductivity field.

54 ENVIRONMENTAL SCIENCES↗

A 15,000-hour cyclic endurance test of an 8-centimeter-diameter electron bombardment mercury ion thruster

A laboratory model 8 cm thruster with improvements to minimize ion chamber erosion and peeling of sputtered metal was subjected to a cyclic endurance test for 15,040 hours and 460 restarts. A charted history of several thruster operating variables and off-normal events are shown in 600-hour segments at three points in the test. The transient behavior of these variables during a typical start-stop cycle is presented. Finding of the post-test inspection confirmed most of the expected results. Charge exchange ions caused normal accelerator grid erosion. The workability of the various design features was substantiated, and attainable improvements in propellant utilization efficiency should significantly reduce accelerator erosion.

Nakanishi, S.↗