SEARCH · Search NASA

Results for “Moderator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Erosion in radial inflow turbines. Volume 4: Erosion rates on internal surfaces

An analytic study of the rate at which material is removed by ingested dust impinging on the internal surfaces of a typical radial inflow turbine is presented. Results show that there are several regions which experience very severe erosion loss, and other regions that experience moderate levels of erosion loss: (1) the greatest amount of material loss occurs on the trailing edges of the nozzle blades where very high velocity, moderate angle impacts occur. The tip regions of ductile materials are also subjected to serious levels of erosion loss; (2) moderate amounts of erosion occur near the end of the scroll and on a few of the nozzle blades near this location. Results are presented in the form of surface contours that exist on the scroll and blade surfaces after continuous particulate ingestion with time.

Clevenger, W. B., Jr.↗

NASA NTRS1977

Influence of residual stresses on the tensile strength of composite-metal sandwich laminates

The tensile strength of boron-epoxy/aluminum sandwich laminates is discussed relative to the residual thermal stresses generated by curing and bonding at elevated temperatures. It is shown that the sandwich laminates investigated exhibit three dinstinct modes of failure, depending upon the fiber orientation of the composite. Sandwich laminates with moderate to high percentage of 0-deg fibers exhibit early failures initiated by edge effect; laminates with moderate to high percentage of 90-deg fibers fail according to a first-ply failure criterion; laminates with moderate to high percentages of plus or minus 45 deg plies fail at strains equal to or greater than the failure strain of the corresponding all-composite laminate.

Herakovich, C. T.↗

NASA NTRS1982

Silicon solar cell process development, fabrication and analysis

For UCP Si, randomly selected wafers and wafers cut from two specific ingots were studied. For the randomly selected wafers, a moderate gettering diffusion had little effect. Moreover, an efficiency up to 14% AMI was achieved with advanced processes. For the two specific UCP ingots, ingot #5848-13C displayed severe impurity effects as shown by lower 3sc in the middle of the ingot and low CFF in the top of the ingot. Also the middle portions of this ingot responded to a series of progressively more severe gettering diffusion. Unexplained was the fact that severely gettered samples of this ingot displayed a negative light biased effect on the minority carrier diffusion length while the nongettered or moderately gettered ones had the more conventional positive light biased effect on diffusion length. On the other hand, ingot C-4-21A did not have the problem of ingot 5848-13C and behaved like to the randomly selected wafers. The top half of the ingot was shown to be slightly superior to the bottom half, but moderate gettering helped to narrow the gap.

Iles, P. A.↗

NASA NTRS1984

Boron cosmochemistry

The assumption that boron is a moderately volatile element is examined. It was demonstrated that interior pieces of chondrites contain significantly less boron than had been thought to be indigenous to this type of meteorite. The mean and range of boron abundances in 16 internal pieces of 10 chondrites were significantly smaller than in 126 pieces of 40 chondrites with unknown terrestrial histories. A new value of the cosmic abundance of boron was determined using the geometric average of the results from interior pieces of 10 chondrites. Based upon the thermodynamic assessment of the cosmochemical properties of boron by Cameron, et al. Anders and Ebihara assumed that boron was a moderately volatile element. They renormalized the data of Curtis et al. to a chondrule free basis and thus inferred that the cosmic abundance of boron was about 3 times greater than that proposed by Curtis, et al. To resolve these differences in data, the relative abundances of several elements including boron were measured in 38 carefully prepared interior pieces of 26 different chondrites. Correlation between boron and sulfur abundances, indicate that, contrary to the conclusions of Cameron, et al., boron is not a moderately volatile element.

Curtis, D. B.↗

NASA NTRS1985

Environmental tests of metallization systems for terrestrial photovoltaic cells

Seven different solar cell metallization systems were subjected to temperature cycling tests and humidity tests. Temperature cycling excursions were -50 deg C to 150 deg C per cycle. Humidity conditions were 70 deg C at 98% relative humidity. The seven metallization systems were: Ti/Ag, Ti/Pd/Ag, Ti/Pd/Cu, Ni/Cu, Pd/Ni/Solder, Cr/Pd/Ag, and thick film Ag. All metallization systems showed a slight to moderate decrease in cell efficiencies after subjection to 1000 temperature cycles. Six of the seven metallization systems also evidenced slight increases in cell efficiencies after moderate numbers of cycles, generally less than 100 cycles. The copper based systems showed the largest decrease in cell efficiencies after temperature cycling. All metallization systems showed moderate to large decreases in cell efficiencies after 123 days of humidity exposure. The copper based systems again showed the largest decrease in cell efficiencies after humidity exposure. Graphs of the environmental exposures versus cell efficiencies are presented for each metallization system, as well as environmental exposures versus fill factors or series resistance.

Alexander, P., Jr.↗

NASA NTRS1985

Electrets and plant fluorometers used in field studies to measure hydrogen chloride produced during Space Shuttle launches

The results of the field tests of two monitoring device techniques, electrets and plant fluorometers are analyzed in order to determine the environmental effects of launch by-products and the extent of these effects. The STS launches are used because the Shuttle emits 2 1/2 times more HCl than any previous systems, it produces a voluminous ground cloud and, most important, it produces near field HCl deposition and revolatilization, far-field acid washout/rainout, and gaseous HCl diffusion. Field evaluations of electrets at STS-5, STS-6, and STS-8 have shown that qualitative assessments can be made for areas lightly or moderately impacted by gaseous and aerosol HCl. Field evaluation of the plant productivity fluorometer at STS-8 has shown that this system is also useful for qualitative assessment in areas lightly, moderately, or heavily affected by gaseous and aerosol HCl. Quantitative prediction of HCl may be possible in lightly and moderately affected areas, given deposition rates correlation.

Milligan, J. E.↗

NASA NTRS1989

Antiproton powered propulsion with magnetically confined plasma engines

Matter-antimatter annihilation releases more energy per unit mass than any other method of energy production, making it an attractive energy source for spacecraft propulsion. In the magnetically confined plasma engine, antiproton beams are injected axially into a pulsed magnetic mirror system, where they annihilate with an initially neutral hydrogen gas. The resulting charged annihilation products transfer energy to the hydrogen propellant, which is then exhausted through one end of the pulsed mirror system to provide thrust. The calculated energy transfer efficiencies for a low number density (10(14)/cu cm) hydrogen propellant are insufficient to warrant operating the engine in this mode. Efficiencies are improved using moderate propellant number densities (10(16)/cu cm), but the energy transferred to the plasma in a realistic magnetic mirror system is generally limited to less than 2 percent of the initial proton-antiproton annihilation energy. The energy transfer efficiencies are highest for high number density (10(18)/cu cm) propellants, but plasma temperatures are reduced by excessive radiation losses. Low to moderate thrust over a wide range of specific impulse can be generated with moderate propellant number densities, while higher thrust but lower specific impulse may be generated using high propellant number densities. Significant mass will be required to shield the superconducting magnet coils from the high energy gamma radiation emitted by neutral pion decay. The mass of such a radiation shield may dominate the total engine mass, and could severely diminish the performance of antiproton powered engines which utilize magnetic confinement. The problem is compounded in the antiproton powered plasma engine, where lower energy plasma bremsstrahlung radiation may cause shield surface ablation and degradation.

Lapointe, Michael R.↗

NASA NTRS1990

Cloud altitude determination from infrared spectral radiances

The CO2 slicing method is generally recognized as the most accurate means of inferring cloud altitude from passive infrared radiance observations. The method is applicable to semi-transparent and broken clouds. During the cirrus FIRE and COHMEX field experiments, CO2 channel radiance data suitable for cloud altitude specification were achieved from moderate spectral resolution satellite sounders (NOAA-TOVS and GOES-VAS) and from a High spectral resolution Interferometer Spectrometer (HIS) flown on the NASA U2/ER2 aircraft. Also aboard the ER2 was a down-looking active lidar unit capable of providing cloud top pressure verifications with high accuracy. A third instrument, the Multispectral Atmospheric Mapping Sensor (MAMS) provided 50 meter resolution infrared window data which is used wtih radiosonde data to verify the heights of middle and low level clouds. Comparisons of lidar and MAMS/radiosonde ground truth cloud heights are made with those determined from: high resolution (0.5/cm) HIS spectra, HIS spectra degraded to the moderate resolution (15/cm) of the VAS/TOVS instruments, and spectrally averaged HIS radiances for individual pairs of VAS spectral channels. The results show that the best results are achieved from high resolution spectra; the RMS difference with the ground truth is 23 mb. The RMS differences between the infrared radiance determination and ground truth increase by 35 percent when the spectral resolution is degraded to the moderate spectral resolution of the VAS/TOVS instruments and by 52 to 183 percent, depending upon channel combinations, when only two spectral channels at VAS/TOVS spectral resolution are used.

Smith, William L.↗

NASA NTRS1991

Unified aeroacoustics analysis for high speed turboprop aerodynamics and noise. Volume 5: Propagation of propeller tone noise through a fuselage boundary layer

An analysis of tone noise propagation through a boundary layer and fuselage scattering effects was derived. This analysis is a three dimensional and the complete wave field is solved by matching analytical expressions for the incident and scattered waves in the outer flow to a numerical solution in the boundary layer flow. The outer wave field is constructed analytically from an incident wave appropriate to the source and a scattered wave in the standard Hankel function form. For the incident wave, an existing function - domain propeller noise radiation theory is used. In the boundary layer region, the wave equation is solved by numerical methods. The theoretical analysis is embodied in a computer program which allows the calculation of correction factors for the fuselage scattering and boundary layer refraction effects. The effects are dependent on boundary layer profile, flight speed, and frequency. Corrections can be derived for any point on the fuselage, including those on the opposite side from the source. The theory was verified using limited cases and by comparing calculations with available measurements from JetStar tests of model prop-fans. For the JetStar model scale, the boundary layer refraction effects produce moderate fuselage pressure reinforcements aft of and near the plane of rotation and significant attenuation forward of the plane of rotation at high flight speeds. At lower flight speeds, the calculated boundary layer effects result in moderate amplification over the fuselage area of interest. Apparent amplification forward of the plane of rotation is a result of effective changes in the source directivity due to boundary layer refraction effects. Full scale effects are calculated to be moderate, providing fuselage pressure amplification of about 5 dB at the peak noise location. Evaluation using available noise measurements was made under high-speed, high-altitude flight conditions. Comparisons of calculations made of free field noise, using a current frequency-domain propeller noise prediction method, and fuselage effects using this new procedure show good agreement with fuselage measurements over a wide range of flight speeds and frequencies. Correction factors for the JetStar measurements made on the fuselage are provided in an Appendix.

Magliozzi, B.↗

NASA NTRS1991

Particle bed reactor nuclear rocket concept

The particle bed reactor nuclear rocket concept consists of fuel particles (in this case (U,Zr)C with an outer coat of zirconium carbide). These particles are packed in an annular bed surrounded by two frits (porous tubes) forming a fuel element; the outer one being a cold frit, the inner one being a hot frit. The fuel element are cooled by hydrogen passing in through the moderator. These elements are assembled in a reactor assembly in a hexagonal pattern. The reactor can be either reflected or not, depending on the design, and either 19 or 37 elements, are used. Propellant enters in the top, passes through the moderator fuel element and out through the nozzle. Beryllium used for the moderator in this particular design to withstand the high radiation exposure implied by the long run times.

Ludewig, Hans↗

NASA NTRS1992

Assessment of Potential Aerodynamic Benefits from Spanwise Blowing at the Wing Tip

A comprehensive set of experimental and analytical investigations have been conducted to assess the potential aerodynamic benefits from spanwise blowing at the tip of a moderate aspect ratio, swept wing. An analytical model has been developed to simulate a jet exhausting from the wing tip. An experimental study of a subsonic jet exhausting from the wing tip was conducted to investigate the effect of spanwise blowing from the tip on the aerodynamic characteristics of a moderate aspect ratio, swept wing. Wing force and moment data and surface pressure data were measured at Mach numbers up to 0.72. Results indicate that small amounts of blowing from small jets increase the lift curve slope a small amount, but have no effect on drag. Larger amounts of blowing from longer jets blowing increases lift near the tip and reduce drag at low Mach numbers. These benefits decrease with increasing Mach number, and vanish at Mach 0.5. A Navier-Stokes solver with modified boundary conditions at the tip was used to extrapolate the results to a Mach number of 0.72. With current technology and conventional wing shapes, spanwise blowing at the wing tip does not appear to be a practical means of reducing drag of moderate aspect ratio wings at high subsonic Mach numbers.

Mineck, Raymond Edward↗

NASA NTRS1993

Probing the extent and content of low ionization gas in galaxies: QSO absorption and HI emission

The small projected separations of some QSO's and low-redshift galaxies provide unique opportunities to study the extent and content of gas in galaxies through observation of absorption in the QSO spectra. Observations of these systems provide valuable information on the connection between the absorbing gas and the galaxy, as well as detailed information on the morphology and environment of the galaxy itself. While there is direct evidence that galaxies can produce the intervening-type QSO absorption lines, over the past decade, the study of such 'QSO-galaxy pairs' (at low redshift) has been considered unsuccessful because new detections of absorption were seldom made. A fundamental problem concerning the relation between these low-redshift systems and those seen at moderate to high redshift remains unresolved. Direct and indirect measures of galaxy absorption cross sections at moderate to high redshifts (z is approximately greater than 20.5) are much larger than the optical and HI sizes of local galaxies. However, direct comparison of the low and moderate to high redshift systems is difficult since different ions are observed in different redshift regimes. Observations are presented for a new sample of QSO-galaxy pairs. Nine new QSO's which shine through nearby galaxies (on the sky-plane) were observed to search for CaII absorption in the QSO spectra at the foreground galaxy redshifts.

Womble, Donna S.↗

NASA NTRS1940

Wind-tunnel investigation of an NACA 23030 airfoil with various arrangements of slotted flaps

AN investigation was made of a large-chord NACA 23030 airfoil with a 40- and a 25.66 percent-chord slotted flap to determine the section aerodynamic characteristics of the airfoil affected by flap chord, slot shape, flap position, and flap deflection. The flap positions for maximum lift, the position for minimum drag at moderate and high lift coefficients, and the complete section aerodynamic characteristics of selected optimum arrangements are given. Envelope polar of various flap arrangements are included. The relative merits of slotted flaps of different chords on the NACA 23030 airfoil are discussed, and a comparison is made of each flap size with a corresponding flap size on the NACA 23021 and 23012 airfoils. The lowest profile drags at moderate lift coefficients were obtained with an easy entrance to the slot. The 25.66-percent-chord slotted flap gave lower drag than the 40-percent-chord flap for lift coefficients less than 1.8, but the 40-percent-chord flap gave considerably lower drag for lift coefficients. The drag coefficients at moderate and high lift coefficients were greater with both sizes of flap on the NACA 23030 airfoil than on either the NACA 23021 or the NACA 23012 airfoil. The maximum lift coefficient for the deflections tested with either flap was practically independent of airfoil.

Recant, I G↗

NASA NTRS1947

A Method for Calculating the Heat Required for Windshield Thermal Ice Prevention Based on Extensive Flight Tests in Natural Icing Conditions

An equation is presented for calculating the heat flow required from the surface of an internally heated windshield in order to prevent the formation of ice accretions during flight in specified icing conditions. To ascertain the validity of the equation, comparison is made between calculated values of the heat required and measured values obtained for test windshields in actual flights in icing conditions. The test windshields were internally heated and provided data applicable to two common types of windshield configurations; namely the V-type and the type installed flush with the fuselage contours. These windshields were installed on a twin-engine cargo airplane and the icing flights were conducted over a large area of the United States during the winters of 1945-46 and 1946-47. In addition to the internally heated windshield investigation, some test data were obtained for a windshield ice-prevention system in which heated air was discharged into the windshield boundary layer. The general conclusions resulting from this investigation are as follows: 1) The amount of heat required for the prevention of ice accretions on both flush- and V-type windshields during flight in specified icing conditions can be calculated with a degree of accuracy suitable for design purposes. 2) A heat flow of 2000 to 2500 Btu per hour per square foot is required for complete and continuous protection of a V-type windshield in fight at speeds up to 300 miles per hour in a moderate cumulus icing condition. For the same degree of protection and the same speed range, a value of 1000 Btu per hour per square foot suffices in a moderate stratus icing condition. 3) A heat supply of 1000 Btu per hour per square foot is adequate for a flush windshield located well aft of the fuselage stagnation region, at speeds up to 300 miles per hour, for flight in both stratus and moderate cumulus icing conditions. 4) The external air discharge system of windshield thermal ice prevention is thermally inefficient and requires a heat supply approximately 20 times that required for an internal system having the same performance.

ICE FORMATION↗

NASA NTRS1995

Thermal emission from particulate surfaces: A comparison of scattering models with measured spectra

Emissivity spectra of particulate mineral samples are highly dependent on particle size when that size is comparable to the wavelength of light emitted (5-50 micrometers for the midinfrared). Proper geologic interpretation of data from planetary infrared spectrometers will require that these particle size effects be well understood. To address this issue, samples of quartz powders were produced with narrow, well-characterized particle size distributions. Mean particle diameters in these samples ranged from 15 to 227 micrometers. Emission spectra of these powders allow the first detailed comparison of the complex spectral variations with particle size observed in laboratory data with the predictions of radiative transfer models. Four such models are considered here. Hapke's relectance theory (converted to emissivity via Kirchoff's law) is the first model tested. Hapke's more recently published emission theory is also employed. The third model, the 'Mie/Conel' model, uses Mie single scattering with a two-stream approximation for multiple scattering. This model, like the first, is a converted reflec- tance model. Mie scattering assumes particles are both spherical and well separated, which is not true for the quartz powders, but includes diffraction effects. The fourth model uses the Mie solution for single scattering by spheres and inputs those results into the multiple scattering formalism of Hapke's emission theory. The results of the four models are considered in relation to the values of the optical constants n and k. We have grouped these as class 1 (k large), class 2 (k moderate, n is approximately 2), class 3 (k small, n is approximately 2), and class 4 (k small, n is approximately 1). In general, the Mie/Hapke hybrid model does best at predicting variations with grain size. In particular, it predicts changes of the correct pattern, although incorrect magnitude, for class 1 bands, where large increases in emissivity with decreasing grain size are observed. This model also does an excellent job on moderate (class 2) and very weak and intraband (class 3) regions, and correctly predicts the emission maximum and its invariance with grain size near the Christiansen frequency (class 4). The Mie/Hapke hybrid model also has the fewest free parameters of the four models examined, while maintaining the most physical treatment of the radiative transfer. The Mie/Conel model performs as well as the Mie/Hapke hybrid model in strong bands (class 1) but does not accurately model the behavior of moderate (class 2) and very weak (class 3) bands.

Moersch, J. E.↗

NASA NTRS1996

Mobile Propagation Results from Using the ACTS Mobile Terminal

NASA's Advanced Communications Technology Satellite (ACTS) provides an ideal spaced-based platform for analyzing the Ka-band mobile satellite channel. This paper reports on the results of the Ka-band mobile propagation analysis campaign using the ACTS Mobile Terminal (AMT) developed by the Jet Propulsion Laboratory (JPL). The objectives of the mobile propagation experiments were to measure and analyze the fading characteristics of the Ka-band channel. The analysis involved examining pilot tone tests in three environments: lightly shadowed suburban, moderately shadowed suburban, and heavily shadowed suburban. The results indicate that Ka-band pilot tones experience significant multipath and fading effects. It may be possible to design link margins to provide reliable service for the lightly shadowed suburban environment at Ka-band. However, for areas with moderate and heavy shadowing, the link margin required to realize reliable communications with 99% availability is excessive (26 dB for moderate shadowing, and greater then 30 dB for heavy shadowing). An alternate approach would be to use shadowing/fading countermeasures (e.g., interleaved error control coding and antenna diversity). Such mitigation techniques, necessary for reliable Ka-band mobile communication within a suburban environment, are currently being considered within the NASA program.

Pinck, Deborah↗

NASA NTRS1996

Building the Traffic, Navigation, and Situation Awareness System (T-NASA) for Surface Operations

We report the results of a part-task simulation evaluating the separate and combined effects of an electronic moving map display and newly developed HUD symbology on ground taxi performance, under moderate- and low-visibility conditions. Twenty-four commercial airline pilots carried out a series of 28 gate-to-runway taxi trials at Chicago O'Hare. Half of the trials were conducted under moderate visibility (RVR 1400 ft), and half under low visibility (RVR 700 ft). In the baseline condition, where navigation support was limited to surface features and a Jeppesen paper map, navigation errors were committed on almost half of the trials. These errors were virtually abolished when the electronic moving map or the HUD symbology was available; in addition, compare, the baseline condition, both forms of navigation aid yielded an increase in forward taxi speed. The speed increase was greater for HUD than the electronic moving map, and greater under low visibility than under moderate visibility. These results suggest that combination of electronic moving map and HUD symbology has the potential to greatly increase the efficiency of ground operations, particularly under low-visibility conditions.

McCann, Robert S.↗

NASA NTRS1994

Variation of Great Lakes Water Levels Derived from Geosat Altimetry

A technique for using satellite radar altimetry data to estimate the temporal variation of the water level in moderate to large lakes and enclosed seas is described. Great Lakes data from the first 2 years of the U.S. Navy's Geosat Exact Repeat Mission (November 1986 to November 1988), for which there is an improved orbit, are used to demonstrate the technique. The Geosat results are compared to the lake level data collected by the Great Lakes Section, National Ocean Service, National Oceanic and Atmospheric Administration, and are found to reproduce the temporal variations of the five major lakes with Root-Mean-Square error (RMS) ranging from 9.4 to 13.8 cm and a combined average of 11.1 cm. Geosat data are also analyzed for Lake St. Clair, representing a moderate-sized lake, with a resulting rms of 17.0 cm. During this study period, the water level in the Great Lakes varied in a typical annual cycle of about 0.2 m (0.5 in for Lake Ontario) superimposed on a general decline of approximately 0.5 m. The altimeter data reproduced the general decline reasonably well for all the lakes, but the annual cycle was obscured in some lakes due to systematic errors in the altimeter data. Current and future altimetry missions will have markedly improved accuracy which will permit many moderate (25 km diameter) or larger lakes or enclosed seas to be routinely monitored.

Morris, Charles S.↗