Search NASA⌕ Search

SEARCH · Search NASA

Results for “dislocation density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Quantitative nanoscale tracking of oxygen vacancy diffusion inside single ceria grains by in situ transmission electron microscopy

Oxygen vacancy formation and migration in ceria is critical to its electrochemical and catalytic properties in systems for chemical and energy transformation, but its quantification is rather challenging especially at atomic-scale because of disordered distribution. Here we report a rational approach to track oxygen vacancy diffusion in single grains of pure and Sm-doped ceria at -20 °C to 160 °C using in situ (scanning) transmission electron microscopy ((S)TEM). To create a gradient in oxygen vacancy concentration, a small region (~30 nm in diameter) inside a ceria grain is reduced to the C-type CeO 1.68 phase by the ionization or radiolysis effect of a high-energy electron beam. The evolution in oxygen vacancy concentration is then mapped through lattice expansion measurement using scanning nano-beam diffraction or 4D STEM at a spatial resolution better than 2 nm; this allows direct determination of local oxygen vacancy diffusion coefficients in a very small domain inside pure and Sm-doped ceria at different temperatures. Further, the activation energies for oxygen transport are determined to be 0.59, 0.66, 1.12, and 1.27 eV for pure CeO 2 , Ce 0.94 Sm 0.06 O 1.97 , Ce 0.89 Sm 0.11 O 1.945 , and Ce 0.8 Sm 0.2 O 1.9 , respectively, implying that activation energy increases due to impurity scattering. The results are qualitatively supported by density functional theory (DFT) calculations. In addition, our in situ TEM investigation reveals that dislocations impede oxygen vacancy diffusion by absorbing oxygen vacancies from the surrounding areas and pinning them locally. With more oxygen vacancies absorbed, dislocations show extended strain fields with local tensile zone sandwiched between the compressed ones. Therefore, dislocation density should be reduced in order to minimize the resistance to oxygen vacancy diffusion at low temperatures.

36 MATERIALS SCIENCE↗

The influence of laser-induced nanosecond rise-time stress waves on the microstructure and surface chemical activity of single crystal Cu nanopillars

An apparatus and test procedure for fabrication and loading of single crystal metal nanopillars under extremely high pressures (>1 GPa) and strain rates (>10{sup 7} s{sup -1}), using laser-generated stress waves, are presented. Single-crystalline Cu pillars ({approx}1.20 {mu}m in tall and {approx}0.45 {mu}m in diameter) prepared via focused ion beam milling of Cu(001) substrates are shock-loaded using this approach with the dilatational stress waves propagating along the [001] axis of the pillars. Transmission electron microscopy observations of shock-loaded pillars show that dislocation density decreases and that their orientation changes with increasing stress wave amplitude, indicative of dislocation motion. The shock-loaded pillars exhibit enhanced chemical reactivity when submerged in oil and isopropyl alcohol solutions, due likely to the exposure of clean surfaces via surface spallation and formation of surface steps and nanoscale facets through dislocation motion to the surface of the pillars, resulting in growth of thin oxide films on the surfaces of the pillars.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low cycle fatigue behavior of AlSi10Mg(Cu) alloy at high temperature

Highlights: • The cyclic stress response of AlSi10Mg(Cu) alloy in LCF regime is temperature-dependent. • Precipitates transitions were observed after high temperature cycle loading. • Changes in the interaction mechanism between dislocations and nanoparticles lead to different cyclic stress responses. - Abstract: Low cycle fatigue (LCF) behavior of AlSi10Mg(Cu) alloy was investigated at 100 °C and 250 °C over a range of strain amplitude from 0.25% to 0.40%. Cycle stress response, hysteresis loops, fatigue life, as well as post-fatigue microstructure were studied in detail. Except 0.25%, the alloy performed cycle hardening behavior at 100 °C and softening behavior at 250 °C at any given strain amplitude, which corresponded well with the observed phenomena in hysteresis loops. At any given temperature, cyclic stress increases while fatigue life decreases with the increasing strain amplitude. The fatigue life of the studied alloy at 100 °C was higher than that at 250 °C under the same strain amplitude. Fractography indicated that most fatigue crack initiated from casting defects. The fatigue crack propagation was mainly characterized by fatigue striations and tear ridges in any conditions. Section inspection shows that the number of cracked eutectic Si increases with decreasing the temperature or increasing strain amplitude. Post-mortem transmission electron microscopy (TEM) investigations indicated that cyclic hardening behavior at 100 °C was due to the pinning effect of coherent precipitates (β″-Mg{sub 2}Si and GP zones). Most of tiny coherency precipitates and clusters transformed to large semi-coherency Q′ and β′-Mg{sub 2}Si precipitates after cyclic loading at 250 °C, leading to the sharp decrease of pinning number and dislocation density, which is a key reason for the cyclic softening. Another factor is that more dislocations can be activated and dislocation climb is easier at higher temperature.

36 MATERIALS SCIENCE↗

Discrete shear band plasticity through dislocation activities in body-centered cubic tungsten nanowires

Shear band in metallic crystals is localized deformation with high dislocation density, which is often observed in nanopillar deformation experiments. The shear band dynamics coupled with dislocation activities, however, remains unclear. Here, we investigate the dynamic processes of dislocation and shear band in body-centered cubic (BCC) tungsten nanowires via an integrated approach of in situ nanomechanical testing and atomistic simulation. We find a strong effect of surface orientation on dislocation nucleation in tungsten nanowires, in which {111} surfaces act as favorite sites under high strain. While dislocation activities in a localized region give rise to an initially thin shear band, self-catalyzed stress concentration and dislocation nucleation at shear band interfaces cause a discrete thickening of shear band. Our findings not only advance the current understanding of defect activities and deformation morphology of BCC nanowires, but also shed light on the deformation dynamics in other microscopic crystals where jerky motion of deformation band is observed.

36 MATERIALS SCIENCE↗

Containerless processing of single crystals in low-G environment

Experiments on containerless crystal growth from the melt were conducted during Skylab missions SL3 and SL4 (Skylab Experiment M-560). Six samples of InSb were processed, one of them heavily doped with selenium. The concept of the experiment is discussed and related to general crystal growth methods and their merits as techniques for containerless processing in space. The morphology of the crystals obtained is explained in terms of volume changes associated with solidification and wetting conditions during solidification. All samples exhibit extremely well developed growth facets. Analysis by X-ray topographical methods and chemical etching shows that the crystals are of high structural perfection. Average dislocation density as revealed by etching is of the order of 100 per sq cm; no dislocation clusters could be observed in the space-grown samples. A sequence of striations that is observed in the first half of the selenium-doped sample is explained as being caused by periodic surface breakdown.

Walter, H. U.↗

A strong fracture-resistant high-entropy alloy with nano-bridged honeycomb microstructure intrinsically toughened by 3D-printing

Strengthening materials via conventional “top-down” processes generally involves restricting dislocation movement by precipitation or grain refinement, which invariably restricts the movement of dislocations away from, or towards, a crack tip, thereby severely compromising their fracture resistance. In the present study, a high-entropy alloy Al0.5CrCoFeNi is produced by the laser powder-bed fusion process, a “bottom-up” additive manufacturing process similar to how nature builds structures, with the microstructure resembling a nano-bridged honeycomb structure consisting of a face-centered cubic (fcc) matrix and an interwoven hexagonal net of an ordered body-centered cubic B2 phase. While the B2 phase, combined with high-dislocation density and solid-solution strengthening, provides strength to the material, the nano-bridges of dislocations connecting the fcc cells, i.e., the channels between the B2 phase on the cell boundaries, provide highways for dislocation movement away from the crack tip. Consequently, the nature-inspired microstructure imparts the material with an excellent combination of strength and toughness.

36 MATERIALS SCIENCE↗

Synchrotron radiation x-ray topography and defect selective etching analysis of threading dislocations in GaN

The crystal quality of bulk GaN crystals is continuously improving due to advances in GaN growth techniques. Defect characterization of the GaN substrates by conventional methods is impeded by the very low dislocation density and a large scale defect analysis method is needed. White beam synchrotron radiation x-ray topography (SR-XRT) is a rapid and non-destructive technique for dislocation analysis on a large scale. In this study, the defect structure of an ammonothermal c-plane GaN substrate was recorded using SR-XRT and the image contrast caused by the dislocation induced microstrain was simulated. The simulations and experimental observations agree excellently and the SR-XRT image contrasts of mixed and screw dislocations were determined. Apart from a few exceptions, defect selective etching measurements were shown to correspond one to one with the SR-XRT results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Deformation and spallation of a magnesium alloy under high strain rate loading

We investigate deformation and damage of a magnesium alloy, AZ91, under high strain rate (similar to 10(5) s(-1)) loading via planar impact. The soft-recovered specimens are examined with electron back-scatter diffraction (EBSD). EBSD analysis reveals three types of twinning: {1012} extension, {10 (1) over bar1} contraction, and {10 (1) over bar1}-{10 (1) over bar2) double twinning, and their number density increases with increasing impact velocity. The extension twins dominate contraction and double twins in size and number. Dislocation densities of the recovered specimens are evaluated with x-ray diffraction, and increase with increasing impact velocity. X-ray tomography is used to resolve three-dimensional microstructure of shock-recovered samples. The EBSD and tomography results demonstrate that the second phase, Mg17Al12, plays an important role in both deformation twinning and tensile cracking. Deformation twinning appears to be a common mechanism in deformation of magnesium alloys at low, medium and high strain rates, in addition to dislocation motion. (C) 2016 Elsevier B.V. All rights reserved.

EBSD↗

Effect of slip transmission at grain boundaries in Al bicrystals

In this work, the effect of slip transfer on the deformation mechanisms of Al bicrystals was explored using a rate-dependent dislocation-based crystal plasticity model. Three different types of grain boundaries (GBs) were included in the model by modifying the rate of dislocation accumulation near the GB in the Kocks-Mecking law, leading to fully-opaque (dislocation blocking), fully-transparent and partially-transparent GBs. In the latter, slip transmission is only allowed in pairs of SS in neighbor grains that are suitably oriented for slip transfer according to the Luster-Morris parameter. Modifications of the GB character led to important changes in the deformation mechanisms at the GB. In general, bicrystals with fully-opaque boundaries showed an increase in the dislocation density near the GB, which was associated with an increase in the Von Mises stress. In contrast, the dislocation pile-ups and the stress concentration were less pronounced in the case of partially-transparent boundaries as the slip in one grain can progress into the next grain with some degree of continuity. No stress concentrations were found at these boundaries for fully-transparent boundaries, and there was continuity of strain across the boundary, which is not typical of most experimentally observed GBs. Simulations of ideal bicrystals oriented for favorable slip transfer on the most highly favored slip system in grains with high Schmid factors for slip transfer depends on the number of active SS in operation in the neighborhood and that most boundaries will lead to nearly opaque conditions while some boundaries will be transparent. Finally, the model was applied to a particular experimentally observed GB in which slip transfer was clearly operating indicating that the model predicted a nearly transparent GB.

36 MATERIALS SCIENCE↗

A study of damage-free in-situ etching of GaN in metalorganic chemical vapor deposition (MOCVD) by tertiarybutylchloride (TBCl)

This paper reports a study of the effect of NH 3 flow rate and reactor temperature on the tertiarybutylchloride (TBCl) etching of patterned GaN-on-sapphire templates. It is found that a reduced NH 3 flow rate and an elevated reactor temperature can eliminate islands or dots on the surface, while at the same time, enhance the etching around dislocations. TBCl etching was also performed on planar bulk GaN templates with much lower dislocation density. We find an atomically flat and layer-by-layer etching behavior within the region free of dislocations. Surface kinetics analysis reveals a short diffusion length of etching products. Room-temperature photoluminescence (PL) and x-ray photoelectron spectroscopy (XPS) measurements confirm that TBCl etching is capable of removing the damage and impurities induced by plasma etching without introducing additional damage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrogen diffusion in the elastic fields of dislocations in iron

The effect of dislocation stress fields on the sink efficiency thereof is studied for hydrogen interstitial atoms at temperatures of 293 and 600 K and at a dislocation density of 3 × 10{sup 14} m{sup –2} in bcc iron crystal. Rectilinear full screw and edge dislocations in basic slip systems 〈111〉(110), 〈111〉(112), 〈100〉(100), and 〈100〉(110) are considered. Diffusion of defects is simulated by means of the object kinetic Monte Carlo method. The energy of interaction between defects and dislocations is calculated using the anisotropic theory of elasticity. The elastic fields of dislocations result in a less than 25% change of the sink efficiency as compared to the noninteracting linear sink efficiency at a room temperature. The elastic fields of edge dislocations increase the dislocation sink efficiency, whereas the elastic fields of screw dislocations either decrease this parameter (in the case of dislocations with the Burgers vector being 1/2〈111〉) or do not affect it (in the case of dislocations with the Burgers vector being 〈100〉). At temperatures above 600 K, the dislocations affect the behavior of hydrogen in bcc iron mainly owing to a high binding energy between the hydrogen atom and dislocation cores.

74 ATOMIC AND MOLECULAR PHYSICS↗

The effect of temperature on the deformation structure of single crystal nickel based superalloys

Results for the temperature dependence of the yield and flow stress were obtained for the superalloys PWA 1480 and CMSX-2. An extended Copley-Kear (1967) model is used to predict flow stresses from the dislocation densities measured at different strains and temperatures. Differences found between the two superalloys include the development of their dislocation structure, their ductility, and their work hardening characteristics.

Dollar, M.↗

Examining the creep strengthening nanoprecipitation in novel highly reinforced heat resistant steels

Here we studied the creep strengthening nanoprecipitation in novel heat resistant steels strengthened by a high density of stable nanoprecipitates. The results show that the high number density of MX nanoprecipitates within the martensitic laths in these steels comes from the great amount of MX former elements present in their chemical compositions and the high dislocation density generated by the martensitic transformation that takes place during cooling after austenitization. These dislocations act as nucleation sites for these nanoprecipitates during the tempering applied after the austenitization and quenching. Atom probe tomography measurements show that these nanoprecipitates are rich in Nb, V, Cr and N for the HDSN1 and HDSN2 steels and V, Cr and N for the HDSN3 steel. The distribution of the nanoprecipitates within the martensitic laths suggests that the creep strengthening produced by the Nb, V, Cr and N nanoprecipitates in the HDSN1 and HDSN2 steels is more effective at pinning dislocations at high temperature than that obtained in the HDSN3 steel by the V, Cr and N nanoprecipitates. However, the high amount of W in the HDSN3 steel enhances the solid solution strengthening at high temperatures, resulting in a similar high temperature strength for all HDSN steels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Data-Driven Constitutive Model for the Inelastic Response of Metals: Application to 316H Steel

Here, predictions of the mechanical response of structural elements are conditioned by the accuracy of constitutive models used at the engineering length-scale. In this regard, a prospect of mechanistic crystal-plasticity-based constitutive models is that they could be used for extrapolation beyond regimes in which they are calibrated. However, their use for assessing the performance of a component is computationally onerous. To address this limitation, a new approach is proposed whereby a surrogate constitutive model (SM) of the inelastic response of 316H steel is derived from a mechanistic crystal plasticity-based polycrystal model tracking the evolution of dislocation densities on all slip systems. The latter is used to generate a database of the expected plastic response and dislocation content evolution associated with several instances of creep loading. From the database, a SM is developed. It relies on the use of orthogonal polynomial regression to describe the evolution of the dislocation content. The SM is then validated against predictions of the dead load creep response given by the polycrystal model across a range of temperatures and stresses. When the SM is used to predict the response of 316H during complex non monotonic loading, extrapolating to new loading conditions, it is found that predictions compare particularly well against those from the physics-based polycrystal model.

36 MATERIALS SCIENCE↗

Microstructural stability of tantalum-alloyed ferritic-martensitic steel with neutron irradiation to 7.4 dpa at ~490 °C

Specimens of a reduced-activation ferritic-martensitic steel, called CNA1, were irradiated to 7.4 displacements per atom at ~490 °C in the High Flux Isotope Reactor. Vickers hardness and tensile properties revealed consistent softening that is attributed to some recovery during irradiation, with reduced laths and dislocation density. Detailed microstructural characterization by transmission electron microscopy and energy dispersive x-ray spectroscopy showed radiation-induced dislocation loops, few cavities, and slight dissolution of M 23 C 6 and MX precipitates. Partial amorphization was only observed in M 23 C 6 precipitated in matrix. Transmutation somewhat destabilized M 23 C 6 and MX, with a stronger effect on the later one by noticeable depletion of Ta with enriched W, which is consistent with the transmutation calculations. The microstructural evolution and associated strength changes were discussed with the assistance of computational thermodynamics.

36 MATERIALS SCIENCE↗

Shear Deformation of Dry Polycrystalline Olivine Under Deep Upper Mantle Conditions using a Rotational Drickamer Apparatus (RDA)

Shear deformation experiments on dry hot-pressed polycrystalline San Carlos olivine have been conducted at 4.9-9.6 GPa, 1300-1870 K and strain rates of 0.6-7.4 x 10-5 s-1 using a rotational Drickamer apparatus (RDA) at a synchrotron facility. The stress was measured from the orientational dependence of lattice spacing for the (1 3 0), (1 3 1), (1 1 2), (1 2 2), (1 4 0) and (2 4 1) planes, as well as from the dislocation densities. Based on the mechanical and microstructural observations, we infer that deformation occurs by power-law creep involving dislocation glide and climb under high temperature conditions, whereas deformation is due to exponential creep through the Peierls mechanism at relatively low temperatures. In both regimes the strength of olivine at steady-state deformation at these pressures is much larger than those at lower pressures. The activation volumes V* is estimated to be not, vert, similar15-20 x 10-6 m3/mol for the power-law creep. Combined with the previous results under wet conditions, we present the recommended values of flow law parameters on olivine for power-law creep constrained by high-pressure deformation experiments.

43 PARTICLE ACCELERATORS↗

Crack tip microplasticity mediated by microstructure gradients

Abstract Traditional fracture theories infer damage at cracks (local field) by surveying loading conditions away from cracks (far field). This approach has been successful in predicting ductile fracture, but it normally assumes isotropic and homogeneous materials. However, myriads of manufacturing procedures induce heterogeneous microstructural gradients that can affect the accuracy of traditional fracture models. This work presents a microstructure‐sensitive finite element approach to explore the shielding effects of grain size and crystallographic orientation gradients on crack tip microplasticity and blunting. A dislocation density‐based crystal plasticity model conveys texture evolution, grain size effects, and directional hardening by computing the constraint from dislocation structures. The results demonstrate that the microstructure can act as a buffer between the local and far fields that affects the crack tip microplasticity variability. For nominal opening loading, grain size and texture affect the local ductility and induce a non‐negligible multiaxial plastic deformation. Furthermore, driving forces based on measuring displacements away from the crack tip are less affected by the microstructure, which suggests that traditional experimental methods smear out important crack tip variability.

Castelluccio, Gustavo M.↗

Tensile creep properties of a CrMnFeCoNi high-entropy alloy

Tensile creep tests were performed on a CrMnFeCoNi high-entropy alloy at temperatures from 1023 K to 1173 K. A uniform stress exponent 3.7 ± 0.1 was found across all temperatures. The apparent activation energies of creep under various applied stresses were determined to be around 230 kJ/mol and decrease with increasing stress, indicating a stress-assisted, thermally activated behavior. Steady-state creep microstructures feature no subgrain formation and high dislocation density within grains. Based on our results, the creep rate of CrMnFeCoNi is believed to be controlled by both dislocation-dislocation interactions and dislocation-lattice interactions.

36 MATERIALS SCIENCE↗