Search NASA⌕ Search

SEARCH · Search NASA

Results for “doping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Accelerated and heterogeneous corrosion of Cr-doped uranium nitride fuel pellets

The steam oxidation of Cr-doped UN fuel pellets is analyzed during sequential isothermal holds up to 720 °C. In situ neutron diffraction results show how Cr is accommodated in a secondary U 2 CrN 3 phase, leading to the formation of a duplex UN/U 2 CrN 3 microstructure. Under corrosion, the oxidation of the two phases begins at 400 °C for UN and 430 °C for U 2 CrN 3 , respectively. Because the UN phase is preferentially oxidized in the presence of U 2 CrN 3 , addition of Cr in UN based nuclear fuel is found to accelerate the corrosion rate. At 430 °C the oxidation of UN in the UN/U 2 CrN 3 microstructure is ~ 5 times faster than pure UN, increasing to ~19 times faster at 460 °C. The oxidation of U 2 CrN 3 produces UO 2 via the formation of two transient intermediate phases. In situ neutron diffraction enables oxidation processes of UN and U 2 CrN 3 components to be followed separately within the two-phase system.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

3D analysis of abnormal grain growth in calcia doped alumina in the presence of large pores

Abnormal grain growth has been previously found to increase with the inclusion of large pores (∼60 µm in diameter) in 80 ppm calcium doped alumina. However, the two-dimensional analysis could not accurately describe the proximity of the abnormal grains and pores to establish a correlation. This study uses laboratory-based diffraction contrast tomography and x-ray computed tomography to spatially map the pores and abnormal grains in 3D. A preference towards the formation of abnormal grains near large pores is found when compared to all potential sites. This finding supports that the pores may be a nucleation site for complexion transitions that promote abnormal grain growth. The growth of the abnormal grains in a subsequent heat treatment at 1600°C for 16 hrs was also studied. The elongation along the principal axes is similar for both small and large grains, again supporting that abnormal grain growth was facilitated by a complexion transition.

Abnormal grain growth↗
DOE OSTI2024

Microstructural evolution in doped high entropy alloys NiCoFeCr-3X (X=Pd/Al/Cu) under irradiation

Commonly studied equatomic single-phase FCC high entropy alloys based on 3d transition metals like NiCoFeCr do not provide adequate strength and radiation resistance at high doses for nuclear structural applications. In the current study, the major alloying effects like lattice distortion, ordering and clustering tendencies were investigated by adding low concentration of Pd, Al, or Cu respectively to study the doping effects on the ion irradiation response of NiCoFeCr alloy. The alloys were irradiated with 3 MeV Ni 2+ ions at 500 °C to a fluence of 1 × 10 17 /cm 2 at a beam flux of approximately 2.8 × 10 12 ions/cm 2 /s. The microstructural evolution upon irradiation i.e., formation of dislocation networks, radiation induced segregation and precipitation, and void formation were studied in detail. Further, post-irradiation characterization results showed that a Pd addition leads to a high void nucleation rate but controlled void growth, which may be attributed to increased lattice distortion. In Al added HEA, our microstructural analysis indicates that radiation induced ordered L1 2 precipitates do not affect void swelling significantly. Cu addition led to Cu precipitation that drastically suppressed dislocation density and void swelling of the alloy. Additionally, a model was developed to qualitatively describe the trend in void swelling of typical FCC alloys under ion irradiation. This model was able to qualitatively explain the suppression and reappearance of void swelling in ion irradiated alloys that generally occurs near the region with peak implanted ion concentration.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterization of EJ-270 and Ce-doped LiCAF scintillators for the development of high-rate neutron reflectometer detectors

The Second Target Station of the Spallation Neutron Source at Oak Ridge National Laboratory is anticipated to provide a neutron source with ∼20 times increase in peak brightness than the First Target Station. The neutron reflectometers currently in operation at the First Target Station need to be upgraded due to the increased neutron flux. A prototype neutron detector module based upon a pixelated scintillator array readout by silicon photomultipliers is being developed to address the high-rate challenge faced with future neutron reflectometer instruments at the Second Target Station. Two types of scintillator materials were considered for this detector development, i.e., 6 Li-loaded EJ-270 plastic scintillator and Ce-doped LiCAF single crystal. This paper reports the scintillator characterization results, including light yield, pulse shape discrimination performance, capability to detect thermal neutrons in a high γ-ray field, and γ-ray sensitivity. The number of photons produced per neutron capture by EJ-270 and LiCAF:Ce was measured to be 2176 ± 91 and 2651 ± 108, respectively. EJ-270 demonstrated a good capability to discriminate between neutrons and γ-rays by employing the commonly used charge comparison method (figure-of-merit: 1.13 ± 0.01 for an energy cut of 292–426 keVee) and a reasonable performance when using the time-over-threshold techniques; however, no discrimination was observed from LiCAF:Ce regardless of the pulse shape discrimination approaches utilized, making pulse height discrimination necessary for LiCAF:Ce to differentiate between neutrons and γ-rays. Both EJ-270 and LiCAF:Ce exhibited an acceptable capacity to detect thermal neutrons at high exposure rates up to approximately 584 mR/h. Furthermore, the γ-ray sensitivities measured with a 60 Co source at an exposure rate of around 1145 mR/h were determined to be (6.11 ± 0.87) × 10 −6 and (7.64 ± 1.08) × 10 −7 for EJ-270 and LiCAF:Ce, respectively.

EJ-270↗
DOE OSTI2026

Engineering acid-base active sites on an N-doped biochar catalyst for microwave-assisted biodiesel production from waste cooking oil

Acid-base bifunctional catalysts play a crucial role in converting high-free fatty acid (FFA) feedstocks into biodiesel by enabling the simultaneous esterification and transesterification of triglycerides in a single step, thereby minimizing saponification and streamlining the process. In this study, we report the design and development of a novel N-doped acid-base bifunctional biochar catalyst synthesized from renewable biomass precursors- glucose and chitosan. The catalyst’s acidic sites were introduced via surface functionalization with o-sulfobenzoic acid cyclic anhydride, grafting -SO₃H groups onto the carbon framework, while basic sites were generated from amine functionalities (-NH) derived from chitosan, yielding a robust and truly bifunctional surface. The catalyst was characterized and used for the microwave-assisted transesterification of waste cooking oil, and process optimization using response surface methodology (RSM-CCD) yielding a maximum biodiesel yield of 98.8 ± 0.4% under optimal conditions (methanol-to-oil molar ratio 20:1, catalyst loading 5.7 wt%, temperature 99 °C, and reaction time 46.6 min). The catalyst demonstrated good stability, maintaining a yield of 92.2 ± 0.4% after eight reuse cycles. A Life Cycle Assessment (LCA) conducted for 1 kg of biodiesel production revealed a global warming potential of 0.85 kg CO 2 eq and human toxicity potential of 1.59 kg 1,4-DB eq, with the largest environmental contributions arising from catalyst preparation and reuse. In conclusion, this work highlights a green and circular approach to biodiesel production, combining renewable catalyst design, waste feedstock utilization, and quantitative sustainability assessment to guide future developments in sustainable catalysis and biofuel engineering.

Bifunctional catalyst↗
DOE OSTI2024

Stabilizing alkaline fuel cells with a niobium-doped brookite titanium dioxide catalyst support

Anion-exchange membrane fuel cells represent a promising and scalable approach for hydrogen energy utilization. However, their development is hindered by the weak bonding between metal catalysts and carbon supports, along with challenges in fabricating electronically/ionically conductive electrodes. Here, we report a composite cathode of Nb-doped brookite TiO 2 nanorods that have robust stability when combined with Pt nanoscale catalysts in an alkaline fuel cell. The composite cathode, fabricated without the addition of an ionomer, delivers a power density of 419 mW cm −2 at a current density of 650 mA cm −2 and a voltage retention of 81% at 100 mA cm −2 after 25 h, substantially outperforming a cathode fabricated from commercial Pt/C. Further investigations of the chemical structure, anion exchange capacity, and mass transfer resistance reveal that a solvent residue derived from N-methylpyrrolidone plays an important role in charge transfer and mass transport in the alkaline fuel cell.

alkaline fuel cell↗
DOE OSTI2025

Ultrafast and Highly Mobile Photocarriers in Monolayer WSe 2 Doped by α-RuCl 3

We report an experimental investigation of photocarrier dynamics in a heterostructure formed by a WSe 2 monolayer stacked on a multilayer α-RuCl 3 flake. The samples were fabricated using mechanical exfoliation and dry transfer techniques. Photoluminescence measurements showed that the excitonic photoluminescence of WSe 2 is quenched by more than 3 orders of magnitude upon contact with α-RuCl 3 . Transient absorption measurements revealed an ultrashort photocarrier lifetime of 0.5 ps in the heterostructure. Spatially resolved transient absorption microscopy measurements were employed to probe the transport properties of these photocarriers, resulting in a room-temperature diffusion coefficient of 370 cm 2 s –1 , which is higher than the exciton diffusion coefficients of most previously studied 2D semiconductors. Furthermore, these results suggest that α-RuCl 3 -doped WSe 2 could be utilized in high-speed optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Heterogenous Integration of Boron-Doped p -Diamond with Monolayer n -MoS 2 for PN Junctions Operating at Room Temperature

Diamond has tremendous potential for power electronics, due to its superior thermal conductivity, large electric field strength, and high carrier mobilities. However, the absence of a reliable room temperature n-type transport has impeded any advancements in diamond-based electronics. Here, we circumvent this bottleneck by integrating n-type two-dimensional (2D) monolayers of molybdenum disulfide (MoS 2 ) with boron doped p-type single crystal diamond and demonstrate 2D/3D heterostructure-based PN junction diodes that operate at room temperature with excellent rectification characteristics. Our diodes achieve a maximum forward current density (J D ) of ∼4000 A/cm 2 , an ideality factor (η) value of ∼3.7, and a rectification ratio (RR) of 10 6 . We find that the origin of current rectification stems from the interlayer recombination of majority carriers driven by direct tunnelling (DT) and Fowler Nordheim (FN) tunnelling mechanisms. In conclusion, our demonstration can open new avenues for diamond-based power electronics through its integration with 2D materials.

2D/3D integration↗
DOE OSTI2025

Dual Feedstock Upcycling of α-Methylstyrene-Doped Poly(methyl methacrylate) and Biomass via the Telescope of Depolymerization and Diels–Alder Reaction

Nearly 90% of poly(methyl methacrylate) (PMMA) is not recycled and instead ends up in landfills. Conventional pyrolysis of PMMA recovers impure methyl methacrylate (MMA) with low economic value. Here, we present a telescoped dual upcycling strategy that integrates PMMA depolymerization, Diels–Alder cycloaddition, and aromatization to convert AMS-doped PMMA and biomass-derived 2,5-dimethylfuran (DMF) into 1,2,4-trimethylbenzene (pseudocumene), a valuable chemical feedstock. BBr 3 proved effective in promoting the challenging Diels–Alder reaction between MMA and DMF under high pressure of argon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Stability of Mn-Doped TiO 2 Thin-Film Anodes during Water Oxidation Reactions

Incorporating manganese atoms into TiO 2 has been shown to improve its activity for water oxidation. However, its activity has been observed to steadily degrade under constant applied potential, especially at more oxidizing applied potentials. Here, the compositional profile and electrochemical stability of Mn-doped TiO 2 (Mn:TiO 2 ) thin-film electrodes precisely fabricated by atomic layer deposition (ALD) were evaluated to elucidate the mechanisms of electrode degradation. Although ALD enables the deposition of Mn dopants throughout the film thickness, only Mn within 1.5 nm of the surface was observed to be redox active. Annealing Mn:TiO 2 films in air leads to the diffusion of Mn toward the electrode surface and oxidation of the Mn and alters the redox behavior. Annealing endows greater stability to Mn redox behavior but does not fully stabilize the water oxidation current, suggesting that the two electrochemical processes are not precisely correlated. In situ inductively coupled plasma mass spectrometry reveals that Mn is lost from Mn:TiO 2 films at potentials greater than 1.8 V vs RHE. However, the initial Mn loss is equivalent to less than a single ALD layer of MnO x . Longer-term constant potential experiments suggest that Mn is lost from up to 1 nm of the electrode surface but that this loss may account for only a portion of the diminished water oxidation activity.

atomic layer deposition↗
DOE OSTI2025

Electrochemical Behavior of Cerium at an Indium Tin-Doped Oxide Electrode in Acidic Media

The redox behavior and speciation of cerium at mesoporous thin films composed of nanoparticles of indium tin-doped oxide (nITO) electrodes were characterized in pH 4.8, 0.1 M acetate buffer and both 0.1 and 1 M HNO 3 using electrochemical techniques and X-ray photoelectron spectroscopy. Anodic deposition of ceria species from Ce(III) to the nITO electrode was achieved under all solvent conditions via spontaneous condensation of electrochemically generated ceric hydroxide species. In 1 M nitric acid, the rate of CeO 2 dissolution is on the same order as CeO 2 deposition, resulting in negligible amounts of CeO 2 electrodeposited at the nITO surface. The cathodic stripping of CeO 2 from the nITO substrate deposited in 0.1 M nitric acid or pH 4.8 acetate buffer follows a 2-step process where Ce(IV)-oxide is initially reduced to an unstable Ce(III)-oxide species that rapidly undergoes acid catalyzed dissolution to yield soluble Ce(III) (aq) . These findings provide a foundation for the pH and anodic potential controlled deposition of CeO 2 thin films to ITO substrates, which can aid in the development of materials composed of ceria. As a result, they can also be used to infer likely analogous actinide redox behavior and speciation at these electrodes.

Cerium↗
DOE OSTI2024

Photoreversible Color-Switching Cu-Doped TiO2 Nanoparticles for High-Contrast Rewritable Printing

Light-printable rewritable paper that can be used multiple times has attracted extensive attention because of its potential benefits in reducing environmental pollution and energy consumption. Developing rewritable paper with high black-to-colorless contrast, lasting legibility, and a fast response is fascinating but challenging. Here, we integrate the redox chemistry of Cu2+ ions into photoreductive TiO2 nanoparticles to produce Cu-doped TiO2 nanoparticles capable of highly photoreversible switching between colorless and black with excellent contrast and color stability. Incorporating such nanoparticles into hydroxyethyl cellulose produces a rewritable paper with the same appearance as that of conventional paper. More importantly, it demonstrates great features promising for practical applications, including high black-to-colorless contrast, fast light-printing (<20 s), long legible time (>3 days), high reversibility (>50 cycles), high resolution (90 μm), and large scale (A4 size) applicability.

Wang, Wenshou↗
DOE OSTI2026

Topological Hall Effect in Antiferromagnetic Co-Doped Fe 3 GaTe 2

Fe 3 GaTe 2 is van der Waals (vdW) ferromagnet with a Curie temperature T C ranging from 350 K to 380 K, followed upon cooling by a ferrimagnetic transition near room temperature. Substituting Fe with Co was previously reported to induce antiferromagnetism (AFM) at a Co fraction dependent Néel temperature TN. In this work, we confirm the overall phase diagram of the Fe 3-x Co x GaTe 2 series as a function of x and temperature via magnetization and electrical transport measurements. For x ≥ 0.6 the Hall effect is observed to mimic the magnetization as the AF ground state is suppressed by the external magnetic field via a metamagnetic transition, thus displaying an anomalous Hall response. At low temperatures, we also observe a pronounced topological Hall signal peaking at μ 0 H = 4 T, or within the metamagnetic transition region of fields. This observation points to the presence of magnetic field-induced chiral spin textures, such as skyrmions upon approaching magnetization saturation. Remarkably, magnetic force microscopy (MFM) reveals the emergence of nearly circular magnetic domains, with diameters on the order of 100–200 nm, within the antiferromagnetic phase. Here, a detailed analysis of the MFM images indicates that the topological Hall effect is closely linked to the field-induced stabilization of magnetic domain structures, likely exhibiting chiral textures. This observation suggests the possible formation of skyrmions already in the AFM phase, i.e., AFM skyrmions, that evolve into ferromagnetic (FM) ones upon increasing the magnetic field. Consequently, Co-doped Fe 3 GaTe 2 might provide a platform to investigate the transformation of skyrmions, initially coupled antiferromagnetically into ferromagnetic skyrmions, and to explore its impact on the topological and skyrmion Hall effects.

anomalous Hall effect↗
DOE OSTI2025

Nanometer-Scale Fullerene-Type Conjugated Covalent Cages Based on Triazine: Design, Doping with Li + , and H 2 /CO 2 Adsorption

Spherical and hollow molecular cages based on planar triazine (C 3 N 3 ) hubs and aromatic phenylene connectors have been developed. The cages exhibit topologies akin to C 20 , C 60 , and C 70 fullerenes with diameters that range from 2.3 to 4.9 nm. Apertures into the cage interiors are tuned by varying the aromatic connectors situated between the C 3 N 3 -units. The stabilities of the C 3 N 3 cages increase with size owing to reduced bending strain of planar nodes and connectors that make up the spherical aromatic networks. Doping of the cages with Li + reveals the capacity of the cages for significant adsorption of gaseous H 2 and CO 2 . The design of graphene-like spherical cages is also discussed.

DFT calculations↗
DOE OSTI2024

Epitaxial Core/Shell Nanocrystals of (Europium-Doped) Zirconia and Hafnia

A careful design of the nanocrystal architecture can strongly enhance the nanocrystal function. So far, this strategy has faced a synthetic bottleneck in the case of refractory oxides. Here we demonstrate the epitaxial growth of hafnia shells onto zirconia cores and pure zirconia shells onto europium-doped zirconia cores. The core/shell structures are fully crystalline. Upon shelling, the optical properties of the europium dopant are dramatically improved (featuring a more uniform coordination and a longer photoluminescence lifetime), indicating the suppression of nonradiative pathways. These results launch the stable zirconium and hafnium oxide hosts as alternatives for the established NaYF 4 systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Operando Characterization of Fe in Doped Ni x (Fe 1– x )O y H z Catalysts for Electrochemical Oxygen Evolution

Iron-doped nickel oxyhydroxides, Ni x (Fe 1– x )O y H z , are among the most promising oxygen evolution reaction (OER) electrocatalysts in alkaline environments. Although iron (Fe) significantly enhances the catalytic activity, there is still no clear consensus on whether Fe directly participates in the reaction or merely acts as a promoter. To elucidate the Fe’s role, we performed operando X-ray spectroscopy studies supported by DFT on Ni x (Fe 1– x )O y H z electrocatalysts. We probed the reversible changes in the structure and electronic character of Ni x (Fe 1– x )O y H z as the electrode potential is cycled between the resting (here at 1.10 V RHE ) and operational states (1.66 V RHE ). DFT calculations and XAS simulations on a library of Fe structures in various NiO y H z environments are in favor of a distorted local octahedral Fe(III)O 3 (OH) 3 configuration at the resting state with the NiO y H z scaffold going from α-Ni(OH) 2 to γ-NiOOH as the potential is increased. Under catalytic conditions, EXAFS and HERFD spectra reveal changes in p-d mixing (covalency) relative to the resting state between O/OH ligands and Fe leading to a shift from octahedral to square pyramidal coordination at the Fe site. XES measurements and theoretical simulations further support that the Fe equilibrium structure remains in a formal Fe(III) state under both resting and operational conditions. These spectral changes are attributed to potential dependent structural rearrangements around Fe. The results suggest that ligand dissociation leads to the C 4v symmetry as the most stable intermediate of the Fe during OER. This implies that Fe has a weakly coordinated or easily dissociable ligand that could serve to coordinate the O–O bond formation and, tentatively, play an active role in the Ni x (Fe 1– x )O y H z electrocatalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Emergence of low-energy spin waves in superconducting electron-doped cuprates

In order to fully utilize the technological potential of unconventional superconductors, an enhanced understanding of the superconducting mechanism is necessary. In the best performing superconductors, the cuprates, superconductivity is intimately linked with magnetism, although the details of this coupling remain elusive. Here, we address this gap by studying the electron-doped cuprate Nd 1.85 Ce 0.15 CuO 4−δ that has an antiferromagnetic ground state when synthesized and only becomes superconducting after a reductive annealing process. Using neutron spectroscopy, we show that the as-grown crystal exhibits a large spin pseudogap in the magnetic fluctuation spectrum. Annealing removes defects introduced by the commonly employed synthesis method and significantly reduces the spin pseudogap. While the spin pseudogap in the annealed sample likely arises from superconductivity, in the as-grown sample it results from the absence of long-wavelength spin waves. These results reveal a direct connection between defects, magnetism, and superconductivity, offering new insight into the mechanisms underlying high-temperature superconductivity and guiding the design of improved superconducting materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗