Results for “TIP SPEED” — Page 27

NASA NTRS1984

Annoyance caused by propeller airplane flyover noise

Laboratory experiments were conducted to provide information on quantifying the annoyance response of people to propeller airplane noise. The items of interest were current noise metrics, tone corrections, duration corrections, critical band corrections, and the effects of engine type, operation type, maximum takeoff weight, blade passage frequency, and blade tip speed. In each experiment, 64 subjects judged the annoyance of recordings of propeller and jet airplane operations presented at d-weighted sound pressure levels of 70, 80, and 90 dB in a testing room which simulates the outdoor acoustic environment. The first experiment examined 11 propeller airplanes with maximum takeoff weights greater than or equal to 5700 kg. The second experiment examined 14 propeller airplanes weighting 5700 kg or less. Five jet airplanes were included in each experiment. For both the heavy and light propeller airplanes, perceived noise level and perceived level (Stevens Mark VII procedure) predicted annoyance better than other current noise metrics.

Mccurdy, D. A.↗

NASA NTRS1984

Hover test of a full-scale hingeless rotor

The performance and aeroelastic stability in hover of a 9.8-m diameter, hingeless helicopter rotor system was evaluated. Rotor performance and inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients (CT/sigma) between 0.0 and 0.12. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Good agreement is shown between experimental performance data and predicted performance. The influence of different aerodynamic inflow models on predicting damping levels is also shown. The best correlation with experimental stability data was obtained when a dynamic inflow model was used instead of static or quasistatic inflow models. Comparison with other full scale, hingeless rotor data in hover is presented. The hingeless rotor data and data from a full scale, bearingless main rotor test performed on the same general purpose test apparatus were compared. Although the bearingless rotor was more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown. At low thrust levels the bearingless main rotor is less damped than the hingeless rotor.

Warmbrodt, W.↗

NASA NTRS1984

The application of LQR synthesis techniques to the turboshaft engine control problem

A power turbine governor was designed for a recent-technology turboshaft engine coupled to a modern, articulated rotor system using Linear Quadratic Regulator (LQR) and Kalman Filter (KF) techniques. A linear, state-space model of the engine and rotor system was derived for six engine power settings from flight idle to maximum continuous. An integrator was appended to the fuel flow input to reduce the steady-state governor error to zero. Feedback gains were calculated for the system states at each power setting using the LQR technique. The main rotor tip speed state is not measurable, so a Kalman Filter of the rotor was used to estimate this state. The crossover of the system was increased to 10 rad/s compared to 2 rad/sec for a current governor. Initial computer simulations with a nonlinear engine model indicate a significant decrease in power turbine speed variation with the LQR governor compared to a conventional governor.

Pfeil, W. H.↗

NASA NTRS1982

Turbofan noise generation. Volume 2: Computer programs

The use of a package of computer programs developed to calculate the in duct acoustic mods excited by a fan/stator stage operating at subsonic tip speed is described. The following three noise source mechanisms are included: (1) sound generated by the rotor blades interacting with turbulence ingested into, or generated within, the inlet duct; (2) sound generated by the stator vanes interacting with the turbulent wakes of the rotor blades; and (3) sound generated by the stator vanes interacting with the velocity deficits in the mean wakes of the rotor blades. The computations for three different noise mechanisms are coded as three separate computer program packages. The computer codes are described by means of block diagrams, tables of data and variables, and example program executions; FORTRAN listings are included.

Ventres, C. S.↗

NASA NTRS1984

An experimental investigation of the parallel blade-vortex interaction

A scheme for investigating the parallel blade vortex interaction (BVI) has been designed and tested. The scheme involves setting a vortex generator upstream of a nonlifting rotor so that the vortex interacts with the blade at the forward azimuth. The method has revealed two propagation mechanisms: a type C shock propagation from the leading edge induced by the vortex at high tip speeds, and a rapid but continuous pressure pulse associated with the proximity of the vortex to the leading edge. The latter is thought to be the more important source. The effects of Mach number and vortex proximity are discussed.

Caradonna, F. X.↗

NASA NTRS1983

Energy efficient engine. Fan and quarter-stage component performance report

The fan configuration for the general Electric/NASA Energy Efficient Engine was selected following an extensive preliminary design study. The fan has an inlet radius ratio of 0.342 and a specific flowrate of 208.9 Kg/sec/sq. m (42.8 1bm/sec/sq. ft). The design corrected tip speed is 411.5 m/sec (1350 ft/sec) producing a bypass flow total-pressure ratio of 1.65 and a core flow total-pressure ratio of 1.6. The design bypass ratio is 6.8. The aerodynamic design point corresponds to the maximum climb power setting at Mach 0.8 and 10.67 Km (35,000 ft) altitude. The fully-instrumented fan component was tested in the Lynn Large Fan Test Facility in 1981. The overall performance results, reported herein, showed excellent fan performance with the fan meeting all of its component test goals of flow, efficiency and stall margin.

Cline, S. J.↗

NASA NTRS1986

Scaling of helicopter main rotor noise in hover

A 2.1-m-diam, one-sixth-scale model helicopter main rotor was tested in hover at the NASA Ames Outdoor Aerodynamic Research Facility. It had previously been tested in hover in the NASA Ames 40- by 80-Foot Wind Tunnel test section. The primary objective of the tests was to obtain acoustic and performance data on a medium-scale rotor at various thrust coefficients and tip Mach numbers to compare to similar existing data on a full-scale helicopter main rotor. Information is presented on the effects of thrust- and tip-speed variation, the effects of boundary-layer trip strips, and the effects of wind conditions. In addition, a preliminary evaluation of the scaling of helicopter main-rotor noise in hover is presented. A secondary objective was to contribute to a data base that will permit the estimation of facility effects on acoustic testing.

Kitaplioglu, C.↗

NASA NTRS1984

An experimental investigation of the parallel blade-vortex interaction

A scheme for investigating the parallel blade vortex interaction (BVI) has been designed and tested. The scheme involves setting a vortex generator upstream of a nonlifting rotor so that the vortex interacts with the blade at the forward azimuth. The method has revealed two propagation mechanisms: a type C shock propagation from the leading edge induced by the vortex at high tip speeds, and a rapid but continuous pressure pulse associated with the proximity of the vortex to the leading edge. The latter is thought to be the more important source. The effects of Mach number and vortex proximity are discussed.

Caradonna, F. X.↗

NASA NTRS1984

Hover test of a full-scale hingeless rotor

The performance and aeroelastic stability in hover of a 9.8-m diameter, hingeless helicopter rotor system was evaluated. Rotor performance and inplane damping data were obtained for rotor operation beteen 350 and 425 rpm for thrust coefficients (CT/sigma) between 0.0 and 0.12. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Good agreement is shown between experimental performance data and predicted performance. The influence of different aerodynamic inflow models on predicting damping levels is also shown. The best correlation with experimental stability data was obtained when a dynamic inflow model was used instead of static or quasistatic inflow models. Comparison with other full scale, hingeless rotor data in hover is presented. The hingeless rotor data and data from a full scale, bearingless main rotor test performed on the same general purpose test apparatus were compared. Although the bearingless rotor was more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown. At low thrust levels the bearingless main rotor is less damped than the hingeless rotor.

Warmbrodt, W.↗

NASA NTRS1985

The application of LQR synthesis techniques to the turboshaft engine control problem

A power turbine governor was designed for a recent-technology turboshaft engine coupled to a modern, articulated rotor system using Linear Quadratic Regulator (LQR) and Kalman Filter (KF) techniques. A linear, state-space model of the engine and rotor system was derived for six engine power settings from flight idle to maximum continuous. An integrator was appended to the fuel flow input to reduce the steady-state governor error to zero. Feedback gains were calculated for the system states at each power setting using the LQR technique. The main rotor tip speed state is not measurable, so a Kalman Filter of the rotor was used to estimate this state. The crossover of the system was increased to 10 rad/s compared to 2 rad/sec for a current governor. Initial computer simulations with a nonlinear engine model indicate a significant decrease in power turbine speed variation with the LQR governor compared to a conventional governor.

Pfeil, W. H.↗

NASA NTRS1986

Helicopter rotor and engine sizing for preliminary performance estimation

Methods are presented for estimating some of the more fundamental design variables of single-rotor helicopters (tip speed, blade area, disk loading, and installed power) based on design requirements (speed, weight, fuselage drag, and design hover ceiling). The well-known constraints of advancing-blade compressibility and retreating-blade stall are incorporated into the estimation process, based on an empirical interpretation of rotor performance data from large-scale wind-tunnel tests. Engine performance data are presented and correlated with a simple model usable for preliminary design. When approximate results are required quickly, these methods may be more convenient to use and provide more insight than large digital computer programs.

Talbot, P. D.↗

NASA NTRS1987

Design and performance of controlled-diffusion stator compared with original double-circular-arc stator

The capabilities of two stators, one with controlled-diffusion (CD) blade sections and one with double-circular-arc (DCA) blade sections, were compared. A CD stator was designed and tested that had the same chord length but half the blades of the DCA stator. The same fan rotor (tip speed, 429 m/sec; pressure ratio, 1.65) was used with each stator row. The design and analysis system is briefly described. The overall stage and rotor performances with each stator are compared, as are selected blade element data. The minimum overall efficiency decrement across the stator was approximately 1 percentage point greater with the CD balde sections than with the DCA blade sections.

Gelder, Thomas F.↗

NASA NTRS1987

Cruise noise of the 2/9th scale model of the Large-scale Advanced Propfan (LAP) propeller, SR-7A

Noise data on the Large-scale Advanced Propfan (LAP) propeller model SR-7A were taken in the NASA Lewis Research Center 8 x 6 foot Wind Tunnel. The maximum blade passing tone noise first rises with increasing helical tip Mach number to a peak level, then remains the same or decreases from its peak level when going to higher helical tip Mach numbers. This trend was observed for operation at both constant advance ratio and approximately equal thrust. This noise reduction or, leveling out at high helical tip Mach numbers, points to the use of higher propeller tip speeds as a possible method to limit airplane cabin noise while maintaining high flight speed and efficiency. Projections of the tunnel model data are made to the full scale LAP propeller mounted on the test bed aircraft and compared with predictions. The prediction method is found to be somewhat conservative in that it slightly overpredicts the projected model data at the peak.

Dittmar, James H.↗

NASA NTRS1986

The role of wind tunnel models in helicopter noise research

A study was conducted to determine the applicability of using small-scale powered helicopter models operating in nonanechoic wind tunnels to predict the sound pressure levels of full-scale rotor harmonic noise components. The investigation included noise generation due to high-tip-speed effects, tandem-rotor blade/vortex interactions, single rotors operating on test towers, and the interaction between main rotor vortices and tail rotors. In all cases it was found that the pressure time history waveforms characteristic of different noise-generating mechanisms were properly reproduced by the models. Corrections for microphone locations, acoustical reverberation, and tunnel wind velocity were developed. Application of these corrections to the model data were found to yield satisfactory correlation with full-scale sound pressure levels except for the isolated single rotor, where highly transient data, both model and full-scale, recluded good agreement of absolute values.

Sternfeld, H., Jr.↗

NASA NTRS1988

Coupled Aerodynamic/Acoustical Predictions For Turboprops

Report discusses use of coupled aerodynamic/ and acoustical computer codes to predict noise emitted by turbopropeller blades turning at supersonic tip speeds. To predict noise field, existing turboprop-noise computer code by Farassat modified to accept blade-pressure inputs from three-dimensional turbofan aerodynamical computer code by Denton.

Clark, Bruce J.↗

NASA NTRS1988

Regressed relations for forced convection heat transfer in a direct injection stratified charge rotary engine

Currently, the heat transfer equation used in the rotary combustion engine (RCE) simulation model is taken from piston engine studies. These relations have been empirically developed by the experimental input coming from piston engines whose geometry differs considerably from that of the RCE. The objective of this work was to derive equations to estimate heat transfer coefficients in the combustion chamber of an RCE. This was accomplished by making detailed temperature and pressure measurements in a direct injection stratified charge (DISC) RCE under a range of conditions. For each specific measurement point, the local gas velocity was assumed equal to the local rotor tip speed. Local physical properties of the fluids were then calculated. Two types of correlation equations were derived and are described in this paper. The first correlation expresses the Nusselt number as a function of the Prandtl number, Reynolds number, and characteristic temperature ratio; the second correlation expresses the forced convection heat transfer coefficient as a function of fluid temperature, pressure and velocity.

Lee, Chi M.↗

NASA NTRS1988

Impact of ETO propellants on the aerothermodynamic analyses of propulsion components

The operating conditions and the propellant transport properties used in Earth-to-Orbit (ETO) applications affect the aerothermodynamic design of ETO turbomachinery in a number of ways. Some aerodynamic and heat transfer implications of the low molecular weight fluids and high Reynolds number operating conditions on future ETO turbomachinery are discussed. Using the current SSME high pressure fuel turbine as a baseline, the aerothermodynamic comparisons are made for two alternate fuel turbine geometries. The first is a revised first stage rotor blade designed to reduce peak heat transfer. This alternate design resulted in a 23 percent reduction in peak heat transfer. The second design concept was a single stage rotor to yield the same power output as the baseline two stage rotor. Since the rotor tip speed was held constant, the turbine work factor doubled. In this alternate design, the peak heat transfer remained the same as the baseline. While the efficiency of the single stage design was 3.1 points less than the baseline two stage turbine, the design was aerothermodynamically feasible, and may be structurally desirable.

Civinskas, K. C.↗

NASA NTRS1987

Cruise noise of the 2/9 scale model of the Large-scale Advanced Propfan (LAP) propeller, SR-7A

Noise data on the Large-scale Advanced Propfan (LAP) propeller model SR-7A were taken in the NASA Lewis Research Center 8 x 6 foot Wind Tunnel. The maximum blade passing tone noise first rises with increasing helical tip Mach number to a peak level, then remains the same or decreases from its peak level when going to higher helical tip Mach numbers. This trend was observed for operation at both constant advance ratio and approximately equal thrust. This noise reduction or, leveling out at high helical tip Mach numbers, points to the use of higher propeller tip speeds as a possible method to limit airplane cabin noise while maintaining high flight speed and efficiency. Projections of the tunnel model data are made to the full scale LAP propeller mounted on the test bed aircraft and compared with predictions. The prediction method is found to be somewhat conservative in that it slightly overpredicts the projected model data at the peak.

Dittmar, James H.↗