Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Reversible solid oxide cells: Early performance and microstructural evolution during electrolysis and switched mode operation

Incorporating more renewables into our energy mix will require a diversity of technological solutions. Reversible solid oxide cell systems (RSOCs) operating reversibly between fuel cell and electrolysis modes with high round-trip efficiencies offer one such solution. However, questions remain about the stability of the oxygen and fuel electrodes under reversible operation. Here, in this study, single cells with the configuration Ni-YSZ|YSZ|GDC10|NNO-NDC50|NNO are operated by reversible cycling under potentiostatic conditions. Test conditions are chosen to be representative of average stack conditions that are likely to be encountered during operation of a stack constructed of such cells. The results of reversible cycling over 500 h (21 cycles) are compared with operating the cells under potentiostatic conditions in the electrolysis-only mode (i.e., without cycling). Voltage-current density (DC), AC complex impedance spectroscopy, distribution of relaxation times (DRT) analysis, and scanning electron microscopy (SEM) indicate excellent reversibility and stability of the neodymium nickelate-based oxygen electrodes in both electrolysis and reversible cycling modes. Degradation behavior is attributed to the loss and coarsening of connected Ni particles in the fuel electrode, particularly in the active layer. However, reversible operation mitigates this degradation compared to operation in the electrolysis-only (SOEC-only) mode.

25 ENERGY STORAGE↗

Controlling swelling in mixed transport polymers through alkyl side-chain physical cross-linking

Semiconducting conjugated polymers bearing glycol side chains can simultaneously transport both electronic and ionic charges with high charge mobilities, making them ideal electrode materials for a range of bioelectronic devices. However, heavily glycolated conjugated polymer films have been observed to swell irreversibly when subjected to an electrochemical bias in an aqueous electrolyte. The excessive swelling can lead to the degradation of their microstructure, and subsequently reduced device performance. An effective strategy to control polymer film swelling is to copolymerize glycolated repeat units with a fraction of monomers bearing alkyl side chains, although the microscopic mechanism that constrains swelling is unknown. Here we investigate, experimentally and computationally, a series of archetypal mixed transporting copolymers with varying ratios of glycolated and alkylated repeat units. Experimentally we observe that exchanging 10% of the glycol side chains for alkyl leads to significantly reduced film swelling and an increase in electrochemical stability. Through molecular dynamics simulation of the amorphous phase of the materials, we observe the formation of polymer networks mediated by alkyl side-chain interactions. When in the presence of water, the network becomes increasingly connected, counteracting the volumetric expansion of the polymer film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dendrite Growth Morphology Modeling in Liquid and Solid Electrolytes

The main goal of this project is to develop a multi-scale modeling approach that connects micron-scale phase-field models and atomic-scale density functional theory (DFT)-based simulations via parameter- and relationship-passing in order to predict Li-metal dendrite morphology evolution, in both liquid and solid electrolytes. The key hypothesis of the DFT-informed phase-field multiscale modeling approach is that it can capture the electrochemical-mechanical driving forces and incorporate the roles of nano-meter-thin solid electrolyte interphase (SEI) in liquid electrolytes as well as of the microstructures of micro-meter-thick solid electrolytes (SEs) for all-solid-state batteries. In this project, we have formulated and implemented phase-field models to incorporate the electrochemical driving forces in liquid electrolytes and then incorporate mechanical driving forces to simulate dendrite growth in solid electrolytes with resolved microstructures. We have implemented two treatments for the SEI: an explicit model to include the microstructure of the SE or SEI in the phase field model and an implicit model to simulate the impact of nano-meter thick SEI in liquid electrolytes by varying the electrode/electrolyte interfacial properties. The key interfacial properties, including the electronic and ionic transport properties, the charge transfer reaction kinetics, and mechanical properties, were computed by DFT-based calculations. At the DFT-based model, one key advancement is to directly predict the charge transfer reaction kinetics at a complex Li/SEI/electrolyte interface by linking DFT with density functional tight binding (DFTB) calculations. As the main accomplishments, we have demonstrated two successful predictions in both solid electrolyte and liquid electrolyte based on this multiscale approach. The predicted intergranular Li dendrite growth in LLZO revealed the importance of trapped electrons at internal interfaces in the microstructure of LLZO. The predicted electroplating morphology of mossy Li and faceted Mg agreed well with experiments. The insights provided by the multiscale model and the model enabled electrolyte and SEI design will accelerate the development of Li-metal electrode for high energy density batteries, that meet DOE’s target on cell density (>350 Wh/kg) and cost below $100/kWhuse for EV applications.

25 ENERGY STORAGE↗

A very promising piezoelectric property of Ta{sub 2}O{sub 5} thin films. II: Birefringence and piezoelectricity

Birefringent and piezoelectric properties of Ta{sub 2}O{sub 5} ceramic thin films of monoclinic and trigonal structures were analyzed. The birefringence, observed by reflected polarized light microscopy, yields information on thin film microstructures, crystal shapes and sizes and on crystallographic orientations of grains of trigonal structure. Such an information was considered for investigating piezoelectric properties by laser Doppler vibrometry and by piezoresponse force microscopy. The vibration velocity was measured by applying an oscillating electric field between electrodes on both sides of a Ta{sub 2}O{sub 5} film deposited on a Si substrate which was pasted on an isolating mica sheet. In this case, it is shown that the vibration velocity results were not only from a converse piezoelectric effect, proportional to the voltage, but also from the Coulomb force, proportional to the square of the voltage. A huge piezoelectric strain effect, up to 7.6%, is found in the case of Ta{sub 2}O{sub 5} of trigonal structure. From an estimation of the electrical field through the Ta{sub 2}O{sub 5} thin film, this strain likely corresponds to a very high longitudinal coefficient d{sub 33} of several thousand picometers. Results obtained by piezoresponse force microscopy show that trigonal grains exhibit a polarization at zero field, which is probably due to stress caused expansion in the transition monoclinic-trigonal, presented in a previous article (part I). - Graphical abstract: Image of cross-polarized optical microscopy showing grains of trigonal structure embedded in the monoclinic phase (on the left); (a) mounting of the sample for Laser Doppler Vibrometry, sample constituted of several layers and its equivalent electrical circuit; (b) longitudinal displacements due to converse piezoelectric and Coulomb effects and corresponding piezoelectric strain-U{sub app.}. hystereses. Highlights: > A new Ta{sub 2}O{sub 5} trigonal phase is shown to be birefringent and piezoelectric. > This phase is related to a reversible transition with a monoclinic phase. > The piezoelectricity of this trigonal phase is of several thousands of pm/V. > It is compared to piezoelectricity of the monoclinic phase of several tens of pm/V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Production and characterization of atomized U-Mo powder by the rotating electrode process

In order to produce feedstock fuel powder for irradiation testing, the Idaho National Laboratory has produced a rotating electrode type atomizer to fabricate uranium-molybdenum alloy fuel. Operating with the appropriate parameters, this laboratory-scale atomizer produces fuel in the desired size range for the RERTR dispersion experiments. Analysis of the powder shows a homogenous, rapidly solidified microstructure with fine equiaxed grains. This powder has been used to produce irradiation experiments to further test adjusted matrix U-Mo dispersion fuel. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Impact of Interposer Microstructure on Ionic Transport in Liquid-Phase Bicarbonate Electrolysis

The electrochemical reduction of CO 2 (CO 2 RR) is a potentially scalable approach for converting captured carbon dioxide into value-added products. Conventional gas-phase electrolysis systems can suffer from carbonate crossover, which limits the efficiency of the system. Liquid-phase (bi)carbonate electrolysis using bipolar membrane electrode assemblies (BPMMEA) has emerged as a promising alternative. The interposer layer, a porous mass-transport material between the BPM and the catalyst, is an essential component of the MEA, as it allows evolved CO 2 to reach the catalyst surface for reaction. In the absence of this layer, evolved CO 2 generated by the pH swing process at the BPM can be converted back into (bi)carbonate (CO 2 recapture) due to the high bulk pH. Thus, clear design guidelines are needed to maximize CO 2 conversion, minimize CO 2 recapture in the catholyte, and improve energy efficiency. Here, the transport properties of the interposer are systematically characterized by X-ray tomography and symmetric-cell impedance spectroscopy to quantify porosity, tortuosity, and the resulting MacMullin number. We then examine the correlation between these material properties and the electrolyzer performance. We focus on characterizing two commercial porous membrane filters, mixed cellulose ester (MCE) and poly(ether sulfone) (PES).

CO2 electrolysis↗

Electrochemical Behavior of HVOF-Sprayed Amorphous and Nanocrystalline Fe-Based Fe{sub 73.13}Si{sub 11.12}B{sub 10.79}Cr{sub 2.24}C{sub 2.72} Composite Coatings

The present work describes a series of new amorphous and nanocrystalline composite coatings (composition: 87.6% Fe, 6.7% Si, 2.5% B, 2.5% Cr, 0.7% C in wt.%) on a mild steel substrate made by high-velocity oxy-fuel thermal spray at different feed rates of 20, 30 and 40 g/min. The microstructure characterization using scanning electron microscopy coupled with energy-dispersive spectroscopy shows uniform and adherent coatings of different thickness depending on the feed rate. The structure of the coating is composite in nature (mixture of amorphous and nanocrystalline phases) as confirmed by the x-ray diffraction and transmission electron microscopy. The hardness of the coating is almost 6-7 times than that of the substrate. Though polarization test of the coating demonstrates corrosion resistance in 3.5% NaCl solution similar to the substrate, the difference of corrosion potentials of the coatings and the substrate is largely negative (~ more than 200 mV against saturated calomel electrode) suggesting anodic nature of the coating as compared to the substrate resulting in sacrificial effect.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Carbon Coating Influence on the Formation of Percolating Electrode Networks for Silicon Anodes

Previous studies have demonstrated that chemical vapor deposition carbon coating on silicon (Si@C) can enhance the electrochemical performance of lithium-ion batteries with Si-based anodes. However, the underlying mechanisms contributing to this improvement have not been fully explored. Here, we address this knowledge gap by applying a suite of characterization methods to evaluate Si@C anodes prepared by reducing acetylene on ball-milled Si particles. Raman mapping measurements show that the C coating (<5 nm thick) enables a homogeneous Si and carbon distribution during the slurry casting process, thereby promoting Si utilization during cycling. The coating’s microstructure and morphology were evaluated using X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy, and neutron reflectivity experiments. Electrochemical impedance spectroscopy measurements upon cycling indicate that carbon coating also reduces the overall resistance as benchmarked against bare Si anodes. Galvanostatic cycling in half-cell studies revealed higher initial Coulombic efficiency and specific capacities with increasing carbon coating time. However, solid electrolyte interphase (SEI) investigations using XPS showed that the coated and uncoated samples have very similar characteristics, suggesting that the SEI may only play a minor role in enhancing the performance of Si@C. Full-cell evaluation of the Si electrodes was consistent with half-cell results relating to performance and SEI properties, further supporting the conclusion that electronic and ionic percolation, enabled by effective electrode manufacturing, are the dominant factors contributing to the favorable performance of Si@C.

25 ENERGY STORAGE↗

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗

Ionic conductivity and thermal stability of magnetron-sputtered nanocrystalline yttria-stabilized zirconia

Thermally stable, stoichiometric, cubic yttria-stabilized zirconia (YSZ) thin-film electrolytes have been synthesized by reactive pulsed dc magnetron sputtering from a Zr-Y (80/20 at. %) alloy target. Films deposited at floating potential had a <111> texture. Single-line profile analysis of the 111 x-ray diffraction peak yielded a grain size of approx20 nm and a microstrain of approx2% regardless of deposition temperature. Films deposited at 400 deg. C and selected bias voltages in the range from -70 to -200 V showed a reduced grain size for higher bias voltages, yielding a grain size of approx6 nm and a microstrain of approx2.5% at bias voltages of -175 and -200 V with additional incorporation of argon. The films were thermally stable; very limited grain coarsening was observed up to an annealing temperature of 800 deg. C. Temperature-dependent impedance spectroscopy analysis of the YSZ films with Ag electrodes showed that the in-plane ionic conductivity was within one order of magnitude higher in films deposited with substrate bias corresponding to a decrease in grain size compared to films deposited at floating potential. This suggests that there is a significant contribution to the ionic conductivity from grain boundaries. The activation energy for oxygen ion migration was determined to be between 1.14 and 1.30 eV.

36 MATERIALS SCIENCE↗

Electrochemistry-Induced Restructuring of Tin-Doped Indium Oxide Nanocrystal Films of Relevance to CO 2 Reduction

The electrochemical reduction of CO 2 into fuels using renewable electricity presents an opportunity to utilize captured CO 2 . Electrocatalyst development has been a primary focus of research in this area. This is especially true at the nanoscale, where researchers have focused on understanding nanostructure-property relationships. However, electrocatalyst structure may evolve during operation. Indium- and tin-based oxides have been widely studied as electrocatalysts for CO 2 reduction to formate, but evolution of these catalysts during operation is not well-characterized. Here, we report the evolution of nanoscale structure of precise tin-doped indium oxide nanocrystals under CO 2 reduction conditions. We show that sparse monolayer nanocrystal films desorb from the electrode upon charging, but thicker nanocrystal films remain, likely due to an increased number of physical contacts. Upon applying a cathodic voltage of –1.0 V vs RHE or greater, the original 10-nm diameter nanocrystals are no longer visible, and instead form a larger microstructural network. Elemental analysis suggests the network is an oxygen-deficient indium-tin metal alloy. We hypothesize that this morphological evolution is the result of nanocrystal sintering due to oxide reduction. Furthermore, these data provide insights into the morphological evolution of tin-doped indium oxide nanocrystal electrocatalysts under reducing conditions and highlight the importance of post-electrochemical structural characterization of electrocatalysts.

25 ENERGY STORAGE↗

Operating Stresses and their Effects on Degradation of LSM-Based SOFC Cathodes

The overall goals of the program were: To understand how selected operational parameters affect the performance of solid oxide fuel cells (SOFCs), with a focus on parameters affecting cathodes (air electrodes) comprised of lanthanum strontium manganite (LSM, (La 1-x Sr x ) 1-y MnO 3±δ ) and yttria-stabilized zirconia (YSZ, (Zr 1–z Y z )O 2±δ ). To relate the observed relationships between operational parameters and cell performance to the microstructural changes that can be observed in the cells after operation.

01 COAL, LIGNITE, AND PEAT↗

Effects of Ink Formulation on Construction of Catalyst Layers for High-Performance Polymer Electrolyte Membrane Fuel Cells

Rational design of catalyst layers in a membrane electrode assembly (MEA) is crucial for achieving high-performance polymer electrolyte membrane fuel cells. Establishing a clear understanding of the property (catalyst ink)–structure (catalyst layer)–performance (MEA) relationship lays the foundation for this rational design. Here, a synergistic approach was taken to correlate the ink formulation, the microstructure of catalyst layers, and the resulting MEA performance to establish such a property–structure–performance relationship. The solvent composition (n-PA/H 2 O mixtures) demonstrated a strong influence on the performance of the MEA fabricated with an 830-EW (Aquivion) ionomer, especially polarization losses of cell activation and mass transport. The performance differences were studied in terms of how the solvent composition affects the catalyst/ionomer interface, ionomer network, and pore structure of the resulting catalyst layers. The ionomer aggregates mainly covered the surface of catalyst aggregates acting as oxygen reduction reaction active sites, and the aggregate sizes of the ionomer and catalyst (revealed by ultrasmall angle X-ray scattering and cryo-transmission electron microscopy) were dictated by tuning the solvent composition, which in turn determined the catalyst/ionomer interface (available active sites). In n-PA/H 2 O mixtures with 50~90 wt % H 2 O, the catalyst agglomerates could be effectively broken up into small aggregates, leading to enhanced kinetic activities. The boiling point of the mixed solvents determined the pore structure of ultimate catalyst layers, as evidenced by mercury porosimetry and scanning electron microscopy. For mixed solvents with a higher boiling point, the catalyst–ionomer aggregates in the ink tend to agglomerate during the solvent evaporation process and finally form larger catalyst–ionomer aggregates in the ultimate catalyst layer, resulting in more secondary pores and thus lower mass transport resistance. Both the enlarged catalyst/ionomer interface and appropriate pore structure were achieved with the catalyst layer fabricated from an n-PA/H 2 O mixture with 90 wt % H 2 O, leading to the best MEA performance.

25 ENERGY STORAGE↗

Two types of diffusions at the cathode/electrolyte interface in IT-SOFCs

Analytical transmission electron microscopy, in particular with the combination of energy dispersive X-ray spectroscopy (EDX) and electron energy-loss spectroscopy (EELS), has been performed to investigate the microstructure and microchemistry of the interfacial region between the cathode (La{sub 0.6}Sr{sub 0.4}Co{sub 0.8}Fe{sub 0.2}O{sub 3}, LSCF) and the electrolyte (Gd-doped ceria, GDC). Two types of diffusions, mutual diffusion between cathode and electrolyte as well as the diffusion along grain boundaries, have been clarified. These diffusions suggest that the chemical stability of LSCF and GDC are not as good as previously reported. The results are more noteworthy if we take into consideration the fact that such interdiffusions occur even during the sintering process of cell preparation. - Graphical Abstract: Two types of diffusions, the mutual diffusion and the diffusion along grain boundaries, occurred at the cathode/electrolyte interface of intermediate temperature solid state fuel cells, during cell preparation. The mutual diffusion is denoted by black arrows and the diffusion along grain boundaries assigned by pink arrows. Highlights: > All the cations in cathode (LSCF) and electrolyte (GDC) can mutually diffuse into each other. > Diffusing elements will segregate at grain boundaries or triple junctions around the cathode/electrolyte interface. > Two types of diffusions, the mutual diffusion and diffusion along grain boundaries, have been clarified thereafter.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Activity Convergence between Continuous- and Pulsed-Deposition NiFe Hydroxide Anodes in Liquid Alkaline Electrolyzers

Improving the activity of anodes for the alkaline oxygen evolution reaction (OER) is of interest because of the importance of the reaction in electrochemical technology. There is an abundance of studies which confirm that NiFe hydroxide, often prepared by electrodeposition, is the most active catalyst for the alkaline OER. This relatively high level of confidence in the optimal OER catalyst chemistry suggests that exploration of methods which improve on features besides the chemistry of the films, such as their microstructure, could access new heights of activity. In this study, the possible benefits of pulsed current deposition relative to the conventional continuous current approach to the deposition of NiFe hydroxides were investigated. Pulsed deposition densified the film surfaces by preventing metal ion depletion at the electrode surface during film formation. The Fe content, redox reversibility, and OER activity were higher for the pulsed deposition films relative to their continuous deposition counterparts. Though pulsed deposition imparted a higher OER performance of the films compared to continuous deposition at the three-electrode level, this improved performance was not retained during electrolyzer operation. Rather, a convergence of the cell performance is seen irrespective of the deposition approach. This phenomenon was attributed to the way electrolyzer conditionsrelatively high temperature, base concentration, and current densitycan drive alternate mechanisms for observed performance.

08 HYDROGEN↗